Search
Filters
total: 945
filtered: 762
Search results for: NANOHYDROXYAPATITE COATINGS
-
Bio-based semi-aromatic polyesters for coating applications
PublicationLinear and branched bio-based semi-aromatic (co)polyesters were evaluated as resins for solvent-basedand powder coatings. Dimethyl-2,5-furandicarboxylate (DMF), 2,3-butanediol and various multifunc-tional comonomers were used to synthesize amorphous hydroxyl-end-capped (co)polyesters. The resinswere cross-linked using the -caprolactam blocked trimer of isophorone diisocyanate. Both the solvent-based and powder coatings proved to...
-
The Creation of an Antimicrobial Coating on Contact Lenses by The Use of Nanocopper
PublicationThe aim of the research was to creation an antimicrobial coating on contact lens and examine the ability of copper nanoparticles to decrease microbial adhesion and prevent the growth of bacteria. The creation was based on the immersion method in solution with dispersed nanoparticles of copper at concentration 200 pm. There were evaluated follows factors: time of immersion and base to dispersed nanoparticles. Three solutions: ethyl...
-
Ultrasonic-assisted Electrodeposition of Cu-Sn-TiO2 Nanocomposite Coatings with Enhanced Antibacterial Activity
PublicationCopper-based coatings are known for their high antibacterial activity. In this study, nanocomposite Cu–Sn–TiO2 coatings were obtained by electrodeposition from an oxalic acid bath additionally containing 4 g/dm3 TiO2 with mechanical and ultrasonic agitation. Ultrasound treatment was performed at 26 kHz frequency and 32 W/dm3 power. The influence of agitation mode and the current load on the inclusion and distribution of the TiO2...
-
Mechanical Behavior of Bi-Layer and Dispersion Coatings Composed of Several Nanostructures on Ti13Nb13Zr Alloy
PublicationTitanium implants are commonly used because of several advantages, but their surface modification is necessary to enhance bioactivity. Recently, their surface coatings were developed to induce local antibacterial properties. The aim of this research was to investigate and compare me-chanical properties of three coatings: multi-wall carbon nanotubes (MWCNTs), bi-layer composed of an inner MWCNTs layer and an outer TiO2 layer, and...
-
Functionalization of graphene oxide coatings with phosphorus atoms and their corrosion resistance in sodium chloride environment
PublicationIn this work, we compared corrosion resistance of graphene oxide, and phosphorus functionalized reduced graphene oxide coatings obtained as a result of electrophoretic deposition on the copper substrate. Doping graphene oxide with phosphorus atoms was performed by a hydrothermal method in the presence of different amounts of phosphoric acid. Structural studies confirmed the insertion of phosphorus atoms into the graphene oxide...
-
Effect of MAO coatings on cavitation erosion and tribological properties of 5056 and 7075 aluminum alloys
PublicationTwo ceramic coatings have been applied on 5056 and 7075 aluminum alloy by microarc oxidation (MAO) technology. The mass losses, surface morphologies and the phase constituents of the MAO coatings before and after cavitation tests were examined by means of digital scales, scanning electron microscopy (SEM) and X-ray diffraction (XRD), respectively. In order to assess the impact of the mechanical properties of the surface layer on...
-
Influence of Two-Stage Anodization on Properties of the Oxide Coatings on the Ti–13Nb–13Zr Alloy
PublicationThe increasing demand for titanium and its alloys used for implants results in need of such innovative surface treatment that may jointly increase corrosion resistance and biocompatibility, and demonstrate antibacterial protection at no cytotoxicity. The purpose of this research was to characterize the effect of two-stage anodization, performed for 30 min in phosphoric acid, at the presence of hydrofluoric acid in the second stage....
-
Increase in wear resistance of nickel plasma coatings under traditional and combined treatment conditions
Publication -
Assessment of phase stability and in vitro biological properties of hydroxyapatite coatings composed of hexagonal rods
Publication -
Use of electrochemical methods to examine different surface preparation methods for organic coatings on steel
PublicationObróbka strumieniowo - ścierna jest jedną z powszechnie stosowanych metod przygotowania powierzchni. Wśród nowoczesnych metod coraz większe zainteresowanie wzbudza przygotowanie powierzchni wodą pod wysokim ciśnieniem (z ang. waterjetting). W porównaniu z konwencjonalnymi metodami ''waterjetting'' jest nowoczesną oraz przyjazną środowisku metodą. W literaturze brakuje informacji na temat skuteczności owej metody do zastosowań...
-
Chapter 14 : A new concept of highly porous bioactive titanium alloys with hydroxyapatite coatings
PublicationPrzedstawiono koncepcję biomateriału o wysokiej bioaktywności i odporności na korozję. Omówiono metody wytwarzania porowatych stopów tytanu, techniki utleniania, techniki nakładania porowatego hydroksyapatytu, nakładanie bioaktywnych polimerów, metody badan i modelowania struktur porowatych.
-
Non-destructive inspection of anti-corrosion protective coatings using optical coherent tomography
PublicationW artykule przedstawiono zastosowanie optycznej tomografii koherentnej (OCT) do badania antykorozyjnych powłok ochronnych. Omówiono właściwości optycznej interferometrii niskokoherentnej jako zastosowanej metody pomiarowej, opisano budowę pomiarowego systemu OCT, zbudowanego w Katedrze Metrologii i Optoelektroniki WETI PG. Przy pomocy zrealizowanego systemu przebadano grupę powierzchni metalicznych pokrytych różnymi powłokami antykorozyjnymi....
-
Corrosion behaviour of Cr coatings deposited from Cr(III) formate - urea electrolytes
PublicationPowłoki chromowe były otrzymane z elektrolitów Cr(III) zawierających odpowiednie ligandy, zapewniające ich dobry wygląd. Zbadano wpływ hydrazyny oraz hydrohylo aminofosfatu na właściwości korozyjne Cr otrzymanego z kąpieli mocznikowo-formaldehydowych Cr(III). Właściwości warstw testowano przy pomocy metody EIS rejestrując widma impedancyjne dla próbek o różnych czasach ekspozycji w zakwaszonym roztworze siarczanowym ( pH 2,6) stosując...
-
Engineering and Manufacturing Technology of Green Epoxy Resin Coatings Modified with Recycled Fine Aggregates
Publication -
Development of multilayer coatings for forming dies and tools of aluminium alloy from liquid state
Publication -
Impact of chitosan/noble metals-based coatings on the plasmochemically activated surface of NiTi alloy
Publication -
The Problems of Application of PVD/CVD Thin Hard Coatings for Heavy-Loaded Machine Components
Publication -
UV Curable Coatings Based on Urethane Acrylates Containing Eugenol and Evaluation of Their Antimicrobial Activity
Publication -
Effect of chemical composition on corrosion and wear behaviour of the composite Ni-Fe-Al2O3 coatings.
PublicationPrzedstawiono wyniki badań powłoki kompozytowej otrzymanej przez osadzanie katodowe galwaniczne w roztworze zawierającym sole niklu, żelaza oraz cząstki ceramiki Al2O3 o różnej wielkości i stężeniu. Wykazano, że charakterystyka ceramiki posiada wpływ na szybkość korozji i zużycia ściernego. W szczególności, zawartość ceramiki wpływa dodatnio na odporność na zużycie ścierne, ale nieco obniża odporność na zużycie korozyjne.
-
Weathering Resistance of Waterborne Polyurethane Coatings Reinforced with Silica from Rice Husk Ash
Publication -
Evaluating the performance of organic coatings under mechanical stress using electrochemical impedance spectroscopy
PublicationMimo, iż znaczna liczba konstrukcji zabezpieczanych przy pomocy powłok poddawana jest cyklicznym naprężeniom mechanicznym, czynnik ten wydaje się być niedoceniany jako przyczyniający się do przyspieszonego niszczenia organicznych układów powłokowych. Celem pracy było zweryfikowanie czy powtarzające się naprężenia mechaniczne stanowią istotny element wpływający na skrócenie czasu eksploatacji systemów powłokowych. W tym celu układ:...
-
Mechanical Behavior of Bi-Layer and Dispersion Coatings Composed of Several Nanostructures on Ti Substrate
PublicationThree coatings suitable for biomedical applications, including the dispersion coating composed of multi-wall carbon nanotubes (MWCNTs), MWCNTs/TiO2 bi-layer coating, and MWCNTs-Cu dispersion coating, were fabricated by electrophoretic deposition (EPD) on Ti Grade II substrate. Optical microscopy, scanning electron microscopy, energy-dispersive X-ray spectroscopy, and nanoindentation were applied to study topography, chemical, and...
-
Nanocrystalline CVD Diamond Coatings on Fused Silica Optical Fibres: Optical Properties Study
Publicationpre-treatment by dip coating in two detonation nanodiamond (DND) seeding media has been studied. The DND suspension in ethyl alcohol and dispersion of DND in dimethyl sulfoxide (DMSO) with polyvinyl alcohol (PVA) were chosen for the seeding purpose. The grain size distribution of nanodiamond particles in both seeding media was kept at the same level (approximately 1050 nm). After the seeding nanocrystalline diamond lms were deposited...
-
Wear of Ultra-thin DLC or Tungsten-modified DLC Coatings under Reciprocating Sliding
PublicationIn the paper results are presented from tests in reciprocating sliding of self mated specimens of DLC and tungsten modified DLC coatings on stainless steel substrate. The contact geometry chosen for the research task was ball on flat. The contacts were lubricated either with distilled water or medical saline solution. Results are presented with regard to wear resistance as a function of material type and lubricant used.
-
Thermal Barrier Coatings for High-Temperature Performance of Nickel-Based Superalloys: A Synthetic Review
Publication -
Characteristics of hybrid chitosan/phospholipid-sterol, peptide coatings on plasma activated PEEK polymer
Publication -
Cyclic behavior of FeCoCrNiMn high entropy alloy coatings produced through cold spray
PublicationeCoCrNiMn high entropy alloy powders were employed to produce coatings on carbon steel through high pressure cold spray (at 1100 °C and 7 MPa in temperature and pressure respectively). X-ray diffraction of the sprayed material revealed a dense coating with the retention of the original crystallographic structure. Once splatted, particles revealed high flattening ratio with consequent excellent adhesion of the coating to the substrate....
-
New Transparent Flame-Retardant (FR) Coatings Based on Epoxy-Aluminum Hypophosphite Nanocomposites
PublicationThe present study investigated the flame-retardant (FR) effect of transparent epoxy coating containing aluminum hypophosphite (AHP) nanoparticles (NPs) on polylactic acid (PLA) sheets used as a typical model of combustible polymeric material. First, AHP NPs (≤60 nm) were prepared by a specific two-stage wet milling process and deeply analyzed (morphology, thermal/mechanisms of degradation under nitrogen and air). The thermal properties...
-
Multilayer coatings based on cerium oxide and manganese cobaltite spinel for Crofer22APU SOC interconnects
PublicationThe current state of the art steel interconnect coating materials are based on critical raw material - Co-oxide spinels. Replacing Co-oxide spinels with alternative, abundant materials can reduce the dependence on the critical raw materials. Cobalt-free coatings with the general formula Mn2-xCuFexO4, where x = 0, 0.1, 0.3, were electrophoretically deposited on a ferritic stainless-steel support and evaluated. Prior to deposition,...
-
Research of chitosan coatings deposited by electrophoretic deposition method at various voltage and time parameters
PublicationThe aim of this research is to estimate the electrophoretic deposition main parameters, such as voltage and time duration, that will provide optimal characteristics of the surface layer. Chitosan coatings were synthesized on biomedical Ti13Zr13Nb alloys at 20 V and 30 V and with deposit times of 2min, 5 min, 10 min, and 15 min. Evaluation of the coating was performed by using Scanning Electron Microscope (SEM), Energy-Dispersive...
-
FRP-based reinforcement coatings of steel with application prospects in ships and offshore structures: a review
PublicationLatest research on novel FRP-based anti-corrosion structural coatings (for enhancing structural capacity and strengthening the coating layer) is discussed with application prospects for ships and offshore structures. In the marine environment, structures constantly face corrosion and fatigue cracks. Combining this with high operational and wave loads, it might cause a structural collapse. Recently, polymer composites have been...
-
Performance of zinc-rich coatings evaluated using AFM-based electrical properties imaging
PublicationThe paper presents the results of investigation of polyvinyl zinc-rich coating exposed to 97% relativehumidity atmosphere for 40 days. Condition of the coating and evolution of its protective properties weredetermined with the novel AFM-based approach capable of providing surface profiles, local dc currentmaps as well as local impedance spectra. The proposed technique allowed insight into the local changesof coating topography...
-
Impedance monitoring of corrosion degradation of plasma electrolytic oxidation coatings (PEO) on magnesium alloy
PublicationImpedance technique based on continuous multisinusoidal current perturbation was used to explain degradation process of plasma electrolytic oxidation coatings (PEO) on magnesium alloy. An obtained impedance spectrum was fitted by electrical equivalent circuit to describe properties of conversion layer on magnesium alloy. Additionally, galvanostatic mode maintained during experiment, with DC current equal to zero, allowed to achieve...
-
Arch bridges under test loadings
PublicationThis paper illustrates experience in arch bridges test loadings of the research team of Department of Structural Mechanics and Bridge Structures from the Gdansk University of Technology. The presented calculations results constist the analysis of spatial construction schemes made using the finite elements method (FEM) and its comparison to the field studies. Arch bridges with the longest spans, visualisation of the computational...
-
MOBILITY OF SHALE DRILL CUTTINGS CONSTITUENTS
PublicationThis study focuses on the abundance and mobility of metals and trace elements from shale drill cuttings into the water, being the main component of hydraulic fracturing fluid. The relationship between composition of the shale rock and the potential element release during standard water-based leaching tests was characterized by means of X-Ray Fluorescence spectroscopy (XRF). The XRF analysis confirmed the assumption of shales constituents...
-
Comparative tests of the wall thickness effect of a glass-reinforced thermosetting plastic coating with a non-circular cross section in a soil-coating object for economic aspect
PublicationCulvert structures made of plastics are employed extensively in the construction of new facilities as well as the renovation of existing ones. Due to the high costs of materials required for the manufacturing of these goods, the objective of this research is focused to lessen the thickness of the walls, which may, on the other hand, result in a reduction in the stiffness of the system. In the course of the testing, the structure...
-
Modified Manganese Phosphate Conversion Coating on Low-Carbon Steel
PublicationConversion coatings are one of the primary types of galvanic coatings used to protect steel structures against corrosion. They are created through chemical reactions between the metal surface and the environment of the phosphating. This paper investigates the impact that the addition of new metal cations to the phosphating reaction environment has on the quality of the final coating. So far, standard phosphate coatings have contained...
-
Identification and localization of organic coating degradation onset by impedance imaging
Publication -
Assessment of organic coating degradation via local impedance imaging
PublicationThe paper presents a new approach to organic coating condition evaluation at micrometer scale using localized impedance measurements. It is based on atomic force microscopy (AFM) in contact mode. Impedance is measured between conductive AFM tip and metal substrate covered with organic coating. A single-frequency voltage perturbation signal is applied between the electrodes and current response signal is registered. As the tip is...
-
Current trends in solid-phase microextraction (SPME) fibre catings
PublicationThis critical review presents information on known and innovative approaches to the manufacture of fibre coatings used in solid-phase microextraction (SPME). The properties, advantages and drawbacks of the different types of commercially available SPME fibre coatings are discussed in detail, as are those of novel types of coatings and the methodologies of their preparation. The applications of fibre coatings in the solid-phase...
-
Damage Development on the Surface of Nickel Coating in the Initial Period of Erosion
PublicationThe common occurrence of the phenomenon of cavitation in many industries and the multitude of factors affecting the resistance to cavitation erosion of used materials contribute to the search for methods and appropriate parameters of coating application that are able to minimize the effects of erosion. To determine the validity of the developed application parameters and the method used, cavitation studies and microscopic observations...
-
Measurements of the optical and thermal properties of the 2D black phosphorus coating
PublicationBlack phosphorus is a 2D material, which properties are still being discovered. In this paper, the sensitivity to the temperature of a few-layer black phosphorus coating deposited, on the surface of a microsphere-based fiber-optic sensor, by a dip-coating method is presented. The coating was investigated after 2, 3, and 5 deposition cycles and during temperature growth from 50 °C to 300 °C in an interferometric setup. The intensity...
-
Biological and mechanical research of titanium implants covered with bactericidal coating
PublicationThe paper concerns the biological and mechanical properties of titanium implants with an antibacterial coating. The Ti13Zr13Nb alloy samples were coated with hydroxyapatite (HAp) coatings using the electrophoretic deposition technique (EPD). Subsequently, the surface of the samples was modified with silver, copper, and nickel nanoparticles by the immersion method. Different titanium sample types (i.e. HAp-only and nanometals-enriched...
-
Selection of Organic Coating Systems for Corrosion Protection of Industrial Equipment
PublicationThe most important element of corrosion protection in industrial conditions is the protective coating system. However, selecting the right coating can often be a real problem due to the sheer number of coating manufacturers and their products on the market. A quantitative approach based on the data mining technique used to analyze the obtained multi-site exposure data has been proposed. This was demonstrated by the example of the...
-
Corrosion degradation of spacers – examination of changes in bone cement coating.
PublicationSpacer is a special implant used at the time of infection after endoprosthetic surgery. It consists of a metal core and bone cement coating with an antibiotic. In the human body spacers are exposed to degradation processes. This paper looks at the effect of corrosion on spacers. Electrochemical corrosion tests were performer on titanium pins with bone cement coating in two solutions: Ringer’s solution and artificial...
-
Analysis of compressive forces in CFGFT cylindrical pillars and their coatings using laboratory tests and metric spaces
PublicationThe article discusses compressive forces tests in composite-concrete pillars with the use of laboratory active experiment including the factors and properties of materials which have a significant impact on the test results and their repeatability. A polymer composite based on glass fiber reinforced resin with different fiber beam angles (20, 55 and 85) was used as a buffer/coat of the pole. Due to the problems with direct comparison...
-
The Morphology, Structure, Mechanical Properties and Biocompatibility of Nanotubular Titania Coatings before and after Autoclaving Process
PublicationThe autoclaving process is one of the sterilization procedures of implantable devices. Therefore, it is important to assess the impact of hot steam at high pressure on the morphology, structure, and properties of implants modified by nanocomposite coatings. In our works, we focused on studies on amorphous titania nanotubes produced by titanium alloy (Ti6Al4V) electrochemical oxidation in the potential range 5–60 V. Half of the...
-
An attempt to mechanistically explain the viscoelastic behavior of transparent epoxy/starch-modified ZnO nanocomposite coatings
PublicationThe effects of bare and starch-modified ZnO (ZnO-St) nanoparticles on viscoelastic and mechanical properties are studied by dynamic mechanical and tensile analyses. Transparent epoxy-based nanocomposite films are prepared by incorporating bare or starch-modified ZnO particles into the epoxy matrix. The results demonstrated that ZnO particles hindered the curing reactions and hence the final properties of the cured epoxy. As a result,...
-
Effect of Functionalization of Reduced Graphene Oxide Coatings with Nitrogen and Sulfur Groups on Their Anti-Corrosion Properties
PublicationElectrophoretic production of anticorrosion carbonaceous coatings on copper could be successfully performed by anodic oxidation of negatively charged graphene platelets suspended in an aqueous solution. The various platelets were synthesized by Hummer’s method followed by a hydrothermal reduction in the presence of NH4SCN which was expected to substitute some parts of graphene structure with nitrogen and sulfur groups. X-ray photoelectron...
-
Electrophoretic Deposition of Chitosan/Eudragit E 100/AgNPs Coatings for Controlled Release of Antibacterial Substance
PublicationThe development of bacterial infection of the tissues surrounding an implant is one of the leading causes of implant surgery failure. In order to prevent the deposition of bacteria on the implant surface and the formation of biofilm, coatings that exhibit antibacterial properties are manufactured. However, the problem is the controlled release of the therapeutic substance from the coating over the extended life of the implant [1],...