Filters
total: 990
filtered: 721
-
Catalog
Chosen catalog filters
Search results for: SIOC CERAMIC
-
Nonlinear electrical properties of glass-ceramics nanocomposites containing ferroelectric nanocrystallites of Bi2VO5.5
PublicationNonlinear A.C. impedance measurements were conducted in the 50BiV-50SrBAlO nanocomposite as a function of frequency, temperature and A.C. voltage. This material is ferroelectric below temperature of 730 K, and above 730 K is a good ion-conductor. For this nanocomposite a low A.C. voltage of 1 V rms is enough to observe high nonlinearities. The origin of these nonlinear effects depends on the temperature and frequency. In the high...
-
Fabrication and Structural Properties of LaNb 1‐x As x O 4 Ceramics
PublicationLanthanum niobate substituted with arsenic was synthesized by three methods: solid state reaction from binary oxides and two different methods combining co-precipitation and solidstate reaction. In the first of the combined methods LaNb1- xAsxO4 was synthesized from LaAsO4, obtained from coprecipitation method, and lanthanum and niobium oxides. In the second LaNbO4 was first synthesized from binary oxides and then mixed with LaAsO4...
-
INFLUENCE OF BISMUTH CONTENT ON COMPLEX IMMITTANCE CHARACTERISTICS OF PRESSURELESS SINTERED BiNbO4 CERAMICS
PublicationGoal of the present research was to study immittance properties of BiNbO4 ceramics fabricated by the solid state reaction route followed by pressureless sintering. Four sets of samples were examined, namely the one fabricated from the stoichiometric mixture of oxides, viz. Bi2O3 and Nb2O5 as well as the ones with an excess of 3%, 5% and 10% by mole of Bi2O3. The immittance properties were studied by impedance spectroscopy. Measurements...
-
Material Design and Optimisation of Electrochemical Li-Ion Storage Properties of Ternary Silicon Oxycarbide/Graphite/Tin Nanocomposites
PublicationIn this work, we present the characterization and electrochemical performance of various ternary silicon oxycarbide/graphite/tin (SiOC/C/Sn) nanocomposites as anodes for lithium-ion batteries. In binary SiOC/Sn composites, tin nanoparticles may be produced in situ via carbothermal reduction of SnO2 to metallic Sn, which consumes free carbon from the SiOC ceramic phase, thereby limiting the carbon content in the final ceramic nanocomposite....
-
Structural, thermal and photocatalytic properties of composite materials SiO2/TiO2/C
Publication -
Mechanical properties cement based composites modified with nano-Fe3O4/SiO2
Publication -
Electronic conductivity in the SiO2–PbO–Fe2O3 glass containing magnetic nanostructures
Publication -
The structure of Pb-PbO-SiO2 glass via molecular dynamics simulation
PublicationPraca poświęcona jest badaniom struktury blisko i średniozasięgowej częściowo zredukowanego szkła ołowiowo-krzemianowego o stechiometrii 1Pb1PbO1SiO2 uzyskanego na drodze symulacji dynamiczno-molekularnych. Otrzymane rezultaty porównamy z danymi otrzymanymi dla szkła niemodyfikowanego (2PbO1SiO2) i całkowicie zredukowanego (2Pb1SiO2).
-
Impact damage in SiO2 nanoparticle enhanced epoxy – Carbon fibre composites
PublicationLow velocity impact behaviour of nano-SiO2 enhanced carbon fibre/epoxy composites for naval applications is reported. Epoxy resin matrix was enhanced by 1- 8 wt% SiO2 nanoparticles, based on industrial surface-modified nanosilica. Impact parameters: force, deformation, energy, damage size were recorded. The most pronounced effect was damage size decrease; e.g. ∼28% recorded by infrared thermography and X-ray computed radiography...
-
Fast High-Impedance Spectroscopy Method Using SINC Signal Excitation
PublicationIn this paper the method of fast impedance spectroscopy of technical objects with high impedance (|Zx| > 1 Gohm) is evaluated by means of simulation and practical experiment. The method is based on excitation of an object with a sinc signal and sampling response signals proportional to current flowing through and voltage across the measured impedance. The object impedance spectrum is obtained with use of continuous Fourier transform...
-
Electronic conductivity in the SiO2-PbO-Fe2O3 glass containing magnetic nanostructures
PublicationThe linear impedance spectra of iron–silicate–lead glass samples were measured in the frequency range from 1 MHz to 1 MHz and in the temperature range from 153 K to 423 K. The structure was investigated by means of XRD and atomic force microscopy. Local electrical and magnetic properties of the samples were tested with the aid of electrostatic force microscopy (EFM) and magnetic force microscopy (MFM). The obtained results show...
-
Superconducting properties of NbN-SiO2 sol-gel derived thin films
PublicationPraca przedstawia wyniki badań właściwości nadprzewodzących cienkich warstw xNbN-(100-x)SiO2, gdzie x = 80 mol%, o różnych grubościach (od 450 do 1950 nm. Badania przeprowadzono w oparciu o pomiary przewodnictwa elektrycznego w polu i bez pola magnetycznego. Właściwości nadprzewodzące warstw zależą od ich grubości. Przejście nadprzewodzące warstw jest szerokie, co związane jest z aktywowanym termicznie pełzaniem strumienia pola...
-
Electrical properties of Na2O-CaO-P2O5 glasses doped with SiO2 and Si3N4
PublicationSodium-calcium-phosphate glasses doped with SiO2 or Si3N4 having similar sodium ion concentrations were prepared by melt quenching. The conductivity was measured by impedance spectroscopy under nitrogen atmosphere in a wide frequency range (10 mHz–1 MHz) and wide temperature range (153–473 K). At 36.6 °C, DC conductivities of all glasses vary between 1.1 ∗ 10−12 and 8.9 ∗ 10−12 S cm−1 and have similar activation energies (between...
-
XAFS investigations of nitrided NbN-SiO2 sol-gel derived films
PublicationPraca poświęcona jest wykorzystaniu analizy widm XAFS zmierzonych na krawędzi K atomów Nb do badania struktury cienkich warstw NbN-(100-x)SiO2 (x = 100, 80, 60 mol%) otrzymanych techniką zol-żel poprzez wysokotemperaturowe wygrzewanie warstw Nb2O5-SiO2 w atmosferze NH3. Otrzymana struktura filmu jest złożona z granul NbN ulokowanych w matrycy SiO2. Analiza XAFS pokazuje, że we wszystkich próbkach w lokalnym otoczeniu niobu znajduje...
-
Transport Properties of Nitrided VN-SiO2 Sol-Gel derived films
PublicationPraca dotyczy transportu elektrycznego stałoprądowego cienkich warstw xVN-(100-x)SiO2 (gdzie x = 90, 80, 70, 60 mol%)otrzymanych w wyniku termicznego azotowania warstw tlenkowych otrzymanych metodą zol-żel. W warstwach obserwuje się granule VN rozdyspergowane w amorficznej matrycy SiO2. Warstwy wykazują przejście nadprzewodzące w temperaturze około 7,5K. W stanie normalnym ich przewodnictwo można opisać modelem charaktrystycznym...
-
Ultra-Compact SIRC-Based Self-Triplexing Antenna with High Isolation
PublicationAn ultra-compact self-triplexing antenna realized on a substrate-integrated rectangular cavity (SIRC) is discussed in this study. The proposed structure employs two L-shaped slots and an in-verted U-shaped slot to radiate at three independent operating frequency bands. Three 50-ohm microstrip feed lines are used to excite the radiation in these slots. The operating frequency is individually tuned using the slot size. The slot placement...
-
Properties of Charge Carrier Traps in Lu2O3:Tb,Hf Ceramic Storage Phosphors Observed by High-Pressure Spectroscopy and Photoconductivity
Publication -
Metoda badania powłok ceramicznych w ruchu postępowo-zwrotnym = A method for testing of ceramic coatings under reciprocating sliding
PublicationOpracowano metodę badania powłok ceramicznych w warunkach tarcia ślizgowego na próbkach tworzących układ o styku niekonforemnym kula - powierzchnia płaska. Pokryte warstwą ceramiczną kule dociskano do próbek płaskich - prostopadłościennych listew (również pokrytych ceramiką), wykonujących ruch postępowo-zwrotny. Jako stanowisko badawcze zastosowano Tribometr Posuwisto-zwrotny TPZ-1. Przebieg zużywania się powłoki ceramicznej oceniano...
-
Ruddlesden-Popper-type Nd2-xNi1-yCuyO4±δ layered oxides as candidate materials for MIEC-type ceramic membranes
Publication -
Comparison of Polypropylene and Ceramic Microfiltration Membranes Applied for Separation of 1,3-PD Fermentation Broths and Saccharomyces cerevisiae Yeast Suspensions
Publication -
Effect of hybrid modification by ceramic layer formation in MAO process and laser remelting on the structure of titanium bio-alloy Ti13Nb13Zr
PublicationTo improve the biological properties of titanium alloy Ti13Nb13Zr, hybrid modifications involving micro-arc oxidation (MAO) and Nd: YAG laser remelting were carried out in two combinations. The first consisted of laser modification before the production of the ceramic layer by the micro-arc oxidation process, and the second combination involved Nd: YAG laser modification after the MAO process. The creation of developed surface...
-
New ceramic materials derived from pyrolyzed poly(1,2-dimethylsilazane) and starch as a potential anode for Li-ion batteries
PublicationNewmaterialswere obtained by pyrolysis of starch (S) and poly(1,2-dimethylsilazane) (PSN) (weight ratio: PSN/S 30/70) at temperature a) 500 °C, b) 700 °C and c) 900 °C. Ceramic materials were characterized by infrared spectroscopy, TGA, Raman spectroscopy and SEM. New Si\O and shifted Si\C stretching vibration modes emerged confirming direct interaction between silicon originating fromsilazane and oxygen coming fromstarch. The...
-
Ionic conductivity behavior by activated hopping conductivity (AHC) of barium aluminoborosilicate glass–ceramic system designed for SOFC sealing
PublicationNon-conducting BaO-B2O3-Al2O3-SiO2 parent glasses designed for solid oxide fuel cell (SOFC) sealing applications were prepared using the melt-quenching technique. The glass formation region was determined according to phase equilibrium relations and was found to be in the composition range 70BaO-(x)Al2O3-(10−x)B2O3-20SiO2 where 3.0 < x < 6.0 wt%. The conductivity values obtained conductivity ranged from 10−5 to 10−10 S/cm at temperatures...
-
Hydrogen activated axial inter-conversion in SiC nanowires
Publication -
ASIC Design Example of Complex SoC with FPGA Prototyping
PublicationThe paper presents an example of the System on a Chip design, where the FPGA prototyping has been used. Two FPGA prototypes have been realized. The first FPGA prototype uses AVNET board containing Xilinx Virtex4 device accompanied by custom board with required devices. The second FPGA prototype has been built using the custom PCB with Xilinx Virtex-4 XC4VLX60 FPGA accompanied by all needed external components. The final system...
-
Trójfazowy falownik napięcia z tranzystorami SiC JFET
PublicationW referacie przedstawiono konstrukcję oraz wyniki badań trójfazowego falownika napięcia zbudowanego z wykorzystaniem diod Schottky oraz tranzystorów JFET z węglika krzemu (SiC). Znacznie krótsze czasy przełączeń tych elementów w porównaniu z tranzystorami IGBT i diodami na bazie krzemu (Si) umożliwiają pracę układu z częstotliwością 100 kHz i wyższą. Małe energie przełączeń oraz mała rezystancja drenu tranzystorów SiC JFET pozwalają...
-
Ocena parametrów statycznych diod Schottky'ego z SiC
PublicationPrzedstawiono wyniki pomiarów parametrów statycznych 3 prób diod Schottky'ego produkcji CREE i 2 prób diod Schottky'ego produkcji INFINEON. Stwierdzono, że charakterystyki przy polaryzacji diod w kierunku przewodzenia są w zasadzie identyczne, natomiast przy polaryzacji w kierunku zaporowym wykazują istotne różnice, szczególnie w zakresie napięć w kierunku zaporowym powyżej 600 V
-
ASIC Design Example of Complex SoC with FPGA Prototyping
PublicationThe paper presents an example of the System on a Chip design, where the FPGA prototyping has been used. Two FPGA prototypes have been realized. The first FPGA prototype uses AVNET board containing Xilinx Virtex4 device accompanied by custom board with required devices. The second FPGA prototype has been built using the custom PCB with Xilinx Virtex-4 XC4VLX60 FPGA accompanied by all needed external components. The final system...
-
(Bi,Pb)-Sr-Ca-Cu-O glass-ceramics - superconductor and granular metal
PublicationW materiale o składzie (Bi,Pb)-Sr-Ca-Cu-O wskutek stosowania różnych warunków wytwarzania można otrzymać materiały o różnorodnych właściwościach. W efekcie wygrzewania materiał amorficzny częściowo krystalizuje. To powoduje wzrost rozmiaru i zawartości przewodzących i nadprzewodzących granul oraz zmniejszenie szerokości izolujących barier pomiędzy granulami. Zależność temperaturowa oporu słabo skrystalizowanego materiału jest funkcją...
-
Impact of the addition of dolomite to cream‐firing clays on the technological and color properties of sintered ceramics
Publication -
Fabrication methods of porous perovskite type ceramics for Solid Oxide Fuel Cells (SOFCs)
PublicationPublikacja opisuje metody wytwarzania porowatych materiałów ceramicznych o strukturze perowskitu.
-
The effect of lithium fluoride on the thermal stability and thermoluminescence properties of borosilicate glass and glass-ceramics
Publication -
Electrochemical study of lithium insertion into carbon-rich polymer-derived silicon carbonitride ceramics
PublicationW pracy przedstawiono materiał ceramiczny, bogaty w węgiel krzemo azotek węgla (SiCN), otrzymany na drodze pirolizy w zakresie temperatur od 1100 do 1700°C. Badania elektrochemiczne insercji litu wykazały, że materiał elektrodowy na bazie SiCN może być obiecujący jako anoda w bateriach litowych. Próbka otrzymana w 1300°C cechuje się pojemnością 392 mAh/g i jest stabilna aktywna elektrochemicznie w trakcie interkalacji i deinterkalacji...
-
Influence of Phase Composition on Dielectric Properties of Bismuth-Based Ceramics with Scheelite-Type Structure
PublicationGoal of the present research was to study dielectric properties of BiNbO4 ceramics fabricated by solid state reaction route followed with pressureless sintering. The samples were fabricated from the mixture of oxides, viz. Nb2O5 and Bi2O3. Apart from stoichiometric amount an excess of 3%, 5% and 10% by mole of Bi2O3 was used. It was found that an excess amount of Bi2O3 oxide caused formation of Bi5Nb3O15 minor phase in amount of...
-
X-Ray Diffraction, Mössbauer Spectroscopy and Magnetoelectric Effect Studies of Multiferroic Bi5Ti3FeO15 Ceramics
PublicationBi5Ti3FeO15 ceramics belongs to multiferroic class of materials. In this work it was prepared by solid-state sintering method and investigated by X-ray diffraction, Mössbauer spectroscopy, and magnetoelectric effect measurements. As it was proved by X-ray diffraction studies the single-phase Bi5Ti3FeO15 compound was obtained. The Mössbauer investigations revealed paramagnetic character of the compound at room temperature as well...
-
Wystawa indywidualna artystycznych poszukiwań w ceramice , kontynuacja projektu, "MISAeksperymentCERAMIKA"cz.2
Publication -
Effects of Ca2+, Mg2+, Na+, and K+ substitutions on the microstructure and electrical properties of GdCoO3 ceramics
PublicationGdCoO3-δ, Gd0.975Na0.025CoO3-δ, Gd0.98K0.02CoO3-δ, Gd0.98Ca0.02CoO3-δ, and GdCo0.99Mg0.01O3-δ ceramics were prepared via a solid-state reaction route. Among the dopants studied, substitution with Ca2+ slightly enhanced the densfication of GdCoO3 ceramics. All the lattice parameters of the doped ceramics were larger than those of pure GdCoO3-δ ceramic (a = 5.223 Å, b = 5.389 Å and c = 7.451 Å), and their cell volumes increased by...
-
Mg2+ Doping Effects on the Structural and Dielectric Properties of CaCu3Ti4O12 Ceramics Obtained by Mechanochemical Synthesis
PublicationIn this study, ceramic CaCu3Ti4O12 (CCTO) and CaCu3−xMgxTi4O12 solid solutions in which 0.1 ≤ x ≤ 0.5 were prepared by the mechanochemical method, realized by a high‐energy ball milling technique. The effects of the Mg2+ ion concentration and sintering time on the dielectric response in the prepared ceramics were investigated and discussed. It was demonstrated that, by the use of a sufficiently high energy of mechanochemical treatment,...
-
Mechanism of hopping conduction in Be–Fe–Al–Te–O semiconducting glasses and glass–ceramics
PublicationElectrical properties of beryllium-alumino-tellurite glasses and glass–ceramics doped with iron ions were studied using impedance spectroscopy. The conductivity was measured over a wide frequency range from 10 mHz to 1 MHz and the temperature range from 213 to 473 K. The D.C. conductivity values showed a correlation with the Fe-ion concentration and ratio of iron ions on different valence states in the samples. On the basis of...
-
High-conducting Bi4V2-xFexO11-δ ceramics containing Fe2O3 nanocrystals: Structure and properties
PublicationThe topography, structure, thermal, magnetic, and electrical properties of Bi4V2-xFexO11-δ ceramics substituted with x = 0.5 and 0.7 Fe were studied. The microscope analysis showed the presence of iron-rich nanocrystals formed on the Bi-Fe-V-O grains. The X-ray diffraction studies confirmed that grains are built mostly of tetragonal Bi4V1.5Fe0.5O10.5 phase. Thermal properties analysis showed an order-disorder type γ ↔ γʹ phase...
-
A review on the critical challenges and progress of SiOx-based anodes for lithium-ion batteries
Publication -
Mechanochemical synthesis of nanophotocatalysts SiO2/TiO2/Fe2O3: their structural, thermal and photocatalytic properties
Publication -
Improving carbon dioxide capture in aqueous ammonia solutions by fine SiO2 particles
PublicationAmmonia solutions are considered to be effective solvents for carbon dioxide absorption. Despite the numerous advantages of these solvents, their high volatility is a significant technical and economic problem. Therefore, in this work, silica particles were used as additives to improve CO2 absorption and inhibit NH3 desorption. SiO2 microparticles and colloidal SiO2 particles in the concentration range of 0-0.15 wt.% were used...
-
Structural investigations of nitrided Nb2O5 and Nb2O5-SiO2 sol-gel derived films
PublicationPraca zawiera badania struktury azotowanych warstw Nb2O5-SiO2 (o różnym stosunku molowym Nb2O5/SiO2)otrzymanych metodą zol-żel. Azotowanie przeprowadzono w różnych temperaturach z zakresu 800-1200C. W wyniku azotowania w warstwach powstają metaliczne granule NbN w amorficznej matrycy SiO2. Przemiany strukturalne zachodzące podczas azotowania badano metodą dyfrakcjii rentgenowskiej (XRD), rentgenowską spektroskopią fotoelektronów...
-
Manufacturing and investigation of physical properties of polyacrylonitrile nanofibre composites with SiO2, TiO2and Bi2O3nanoparticles
Publication -
Engineering Au nanoparticle arrays on SiO2 glass by pulsed UV laser irradiation
PublicationWe study semi-regular arrays of Au nanoparticles (NP) obtained via UV laser irradiation of thin Au films on glass substrate. The NP structures are prepared from films of a thickness up to 60 nm produced by discharge sputtering or pulsed laser deposition, and annealed by nanosecond laser pulses at 266 or 308 nm, respectively, at fluencies in the range of 60-410 mJ/cm2. For the rare- and close-packed NP structures, consistent description...
-
STRUKTURA SZKŁO-CERAMIKI ZAWIERAJĄCEJ FERROELEKTRYCZNĄ FAZĘ BiV
PublicationLiteratura opiusuje próby wytworzenia nanokompozytów, w których skład wchodzą matryca szkła i rozproszone w niej nanokrystality fazy ferroelektrycznej. Najczęstsza metoda wykorzystywana do otrzymywania takiej szkło - ceramiki polega na wytopie szkła, a następnie jego krystalizacji. W literaturze można znaleźć dużo przykładów wytwarzania tego typu materiałów dwu lub więcej składnikowych. Najwięcej badań dotyczy ferroelektrycznych...
-
Electrochemical performance of Co3O4/CeO2 electrodes in H2S/H2O atmospheres in a proton-conducting ceramic symmetrical cell with BaZr0.7Ce0.2Y0.1O3 solid electrolyte
PublicationThe electrochemical performance of Co3O4/CeO2 mixed oxide materials as electrodes, when exposed to H2S/H2O atmospheres, was examined employing a proton conducting symmetrical cell, with BaZr0.7Ce0.2Y0.1O3 (BZCY72) as the solid electrolyte. The impact of temperature (700–850 °C) and H2S concentration (0–1 v/v%) in steam-rich atmospheres (90 v/v% H2O) on the overall cell performance was thoroughly assessed by means of electrochemical...
-
Eu3+ doped tellurite glass ceramics containing SrF2 nanocrystals: Preparation, structure and luminescence properties
PublicationEu3+ doped tellurite glass ceramics containing SrF2 nanocrystals were prepared using melt quenching technique and subsequent heat treatment of glass in 370 °C for different time periods. Thermal properties of glass matrix have been determined based on DSC measurements. XRD and XPS results confirmed formation of SrF2 nanocrystals in glass matrices after annealing at 370 °C. FTIR studies revealed absorption bands in the range of...
-
Evaluating the impact of ZnO doping on electrical and thermal properties of calcium-aluminosilicate oxynitride glass-ceramics
PublicationThis study aimed to investigate the impact of ZnO content on the structure, thermal, and electrical properties of oxynitride glass-ceramic(s) within the Ca–Al–Si–O–N (CASON) system. The base glass had the composition of Ca7Al14Si17O52N7, with ZnO additions ranging from 3 to 15 % by weight. A pristine Ca7Al14Si17O52N7 glass was successfully prepared by melt-quenching technique followed by converted into glass-ceramic by incorporating various...