Filters
total: 1332
filtered: 1142
displaying 1000 best results Help
Search results for: AUSTENITIC STEEL
-
Behaviour of deformed steel columns exposed to impact load during earthquakes: numerical analysis
PublicationIt has been observed during earthquakes that the so called soft-storey failure of an upper floor of a building leads to considerable vertical impact load acting on structural members of the lower storeys. The aim of this paper is to investigate numerically the behaviour of horizontally deformed columns (deformation as the result of earthquake loading) that are additionally subjected to vertical impact load. In the first stage of...
-
Nonequilibrium thermodynamic model of diffusion processes in the steel - carbon thin film tribological system
Publication -
Influence of modes of thermal hardening and the subsequent cryogenic processing on structure and properties of steel 38Ni3CrMoV
Publication -
Effect of bending-torsion on fracture and fatigue life for 18Ni300 steel specimens produced by SLM
PublicationIn this study, different fracture surfaces caused by fatigue failure were generated from 18Ni300 steel produced by selective laser melting (SLM). Hollow round bars with a transverse hole were tested under bending-torsion to investigate the crack initiation mechanisms and fatigue life. Next, the post-failure fracture surfaces were examined by optical profilometer and scanning electron microscope. The focus is placed on the relationship...
-
Tool Life and Process Dynamics in High Speed Ball End Milling of Hardened Steel
Publication -
Dry cutting effect in turning of a duplex stainless steel as a key factor in clean production
Publication -
The Effect of a Gear Oil on Abrasion, Scuffing, and Pitting of the DLC-Coated 18CrNiMo7-6 Steel
Publication -
Investigations on surface induced tribological characteristics in MQCL assisted machining of duplex stainless steel
Publication -
Multivariate analysis of impedance data obtained for coating systems of varying thickness applied on steel
PublicationElectrochemical impedance spectroscopy (EIS) has proven to be a valuable test method for the electrochemical characterization of protective coatings on metals. The common way of analysis in impedance spectroscopy is to model the impedance spectrum by means of an equivalent circuit and to extract the quantity of interest using optimization techniques. A model, corresponding to the behavior of the sample under testing, is important...
-
Guided wave propagation in debonding detection in CFRP-reinforced steel plate-like structures
PublicationThe present study investigates the guided wave propagation in multilayered steel specimens reinforced with carbon fiber reinforced polymer (CFRP) through theoretical, numerical, and experimental means. The effectiveness of externally bonded reinforcement (EBR) relies heavily on the bonding quality between the CFRP and the substrate. Premature debonding, a prevalent and hazardous defect, can arise from suboptimal manufacturing processes,...
-
FRP-based reinforcement coatings of steel with application prospects in ships and offshore structures: a review
PublicationLatest research on novel FRP-based anti-corrosion structural coatings (for enhancing structural capacity and strengthening the coating layer) is discussed with application prospects for ships and offshore structures. In the marine environment, structures constantly face corrosion and fatigue cracks. Combining this with high operational and wave loads, it might cause a structural collapse. Recently, polymer composites have been...
-
Seismic probabilistic assessment of steel and reinforced concrete structures including earthquake-induced pounding
PublicationRecent earthquakes demonstrate that prioritizing the retrofitting of buildings should be of the utmost importance for enhancing the seismic resilience and structural integrity of urban structures. To have a realistic results of the pounding effects in modeling process of retrofitting buildings, the present research provides seismic Probability Factors (PFs), which can be used for estimating collision effects without engaging in...
-
Comparision of two numerical methods for buried steel culverts made of corrugated shell sheets.
PublicationW pracy omawia się dwie metody analizy statycznej obudowy tuneli i przepustów dużej średnicy. Pierwsza z nich, metoda sprężyn polega na modelowaniu ośrodka gruntowego radialnymi sprężynami reprezentującymi odkształcalność gruntu. Drugie podejście oparte jest na zastosowaniu metody elementów skończonych i programu SOFISTIC. W układzie obudowa - grunt obudowę modeluje się zwykłymi ramowymi elementami sprężystymi a otaczający...
-
Fatigue tests of steel Sandwich panel. Fifth International Conference on Marine Technology and Transportation.
PublicationW referacie przedstawiono wyniki badań laboratoryjnych paneli SANDWICH prowadzonych w Katedrze Technologii Okrętów, Systemów Jakości i Materiałoznawstwa Wydziału OiO na konstrukcjach w skali rzeczywistej. Dokonano porównania uzyskanych rezultatów w wynikami prezentowanymi w literaturze.
-
Numerical calculations of wall pressures and stresses in steel cylindrical silos with concentric and eccentric hoppers
PublicationArtykuł przedstawia numeryczną analize naprężeń w płaszczu silosa. Porównane zostały wyniki dla silosów o przepływie centrycznym i mimośrodowym.
-
Complementary study with magnetic and acoustic techniques of A336 steel damage state due to creep
PublicationBadano możliwość detekcji w sposób nieniszczący zmian w mikrostrukturze stali A336 poddanej próbie pełzania. Testowano dwie magnetyczne techniki (klasyczny efekt Barkhausena i emisję magnetoakustyczną) oraz dwie nowe techniki ultradźwiękowe (pomiar współczynnika elasto-akustycznego oraz dwójłomność akustyczną). Wykazano, iż wyniki badań akustycznych są komplementarne do wyników badań magnetycznych.
-
Specific risks for local stability and capacity of verticat doble - shell cylindrical steel tanks
PublicationOmówiono zagrożenia stateczności i nosności płaszczy zbiorników dwupłaszczowych wywołane przez: niefachowo prowadzoną próbę wodną, dużną różnicę temperatury podczas eksploatacji oraz nierównomierne osiadanie. W księdze konferncyjnej opublikowano dwustronicowe streszczenie referatów a na załączonej płycie referaty zamieszczone są w całości.
-
Simulation of fracture process in concrete elements with steel fibres using discrete lattice model
PublicationArtykuł omawia wyniki modelowania procesu zarysowania w elementach betonowych zawierające stalowe włókna przy zastosowaniu dyskretnego modelu kratownicowego. Beton był modelowany na poziomie mezoskali z uwzględnieniem 5 faz: kruszywa, zaczynu cementowego, włókien i obu stref kontaktu. Obliczenia wykonano dla jednoosiowego ściskania, jednoosiowego rozciągania i zginania prostego.
-
Full-scale experiments on wheat flow in steel silo composed of corrugated walls and columns
PublicationArtykuł omawia wyniki doświadczalne w dużej skali odnośnie przepływu pszenicy w stalowym silosie wykonanym z blachy falistej i słupów. Pomierzono napory poziome i pionowe na ścianie oraz siły pionowe w słupach. Zbadano rodzaj przepływu w zależności od położenia wylotu. Wyniki naporów porównano z Eurokodem.
-
Effect of steel fibres on concrete behavior in 2D and 3D simulations using lattice model.
PublicationW artykule przedstawiono wyniki numerycznej symulacji betonu zbrojonego włóknami stalowymi. Beton został opisany w skali mezo jako materiał 3-fazowy przy zastosowaniu modelu sieciowego. Obliczenia wykonano dla rozciągania jednoosiowego. Porównano ze sobą wyniki dwu- i trójwymiarowe.
-
Experimental and numerical investigations of size effects in reinforced concrete beams with steel or basalt bars.
PublicationW artykule przedstawiono wyniki obliczeń efektów skali w belkach betonowych zbrojonych prętami stalowymi i bazaltowymi podczas zginania. Zastosowano model sprężysto-plastyczny z nielokalnym osłabieniem. Rozkład wytrzymałości na rozciąganie był stochastyczny – przestrzennie skorelowany. Belki były geometrycznie podobne. Wyniki porównano z modelem efektu skali Bazanta
-
Dissimilar underwater wet welding of HSLA steels
PublicationThe high-strength low-alloy S460ML and S460N steels were chosen for underwater wet welding of dissimilar T-joints using covered electrodes. For improving the quality of joints, the temper bead welding (TBW) method was used. The application of TBW in pad welding conditions has been investigated earlier but the possibility of usage of this technique in welded joints was not analyzed. The main aim of the study was to check the influence...
-
Hydrogen Damage in Superaustenitic 904L Stainless Steels
Publicationresults on the influence of hydrogen on corrosion resistance and of hydrogen embrittlement of 904L superaustenitic stainless steel were investigated. The cracking behavior was studied by performing a slow strain rate test in synthetic seawater under varying cathodic polarization conditions. The results showed that the steel’s plasticity varied with the applied cathodic current density. Significant reductions in ductility were found,...
-
Hydrogen degradation of high strength weldable steels
PublicationW pracy przedstawiono wyniki badań podatności stali spawalnych o wysokiej wytrzymałości na niszczenie wodorowe. Badano dwa gatunki stali S690Q i ich złącza spawane. Ocenę podatności na niszczenie wodorowe wykonano w oparciu o próbę rozciągania z małą prędkością odkształcania w powietrzu i środowisku wody morskiej przy polaryzacji katodowej. Przedstawiono model niszczenia wodorowego badanych stali i ich złączy spawanych.
-
Properties of Vacuum Sintered Duplex Stainless Steels
Publication -
Properties of vacuum sintered duplex stainless steels
Publication -
Properties of Vacuum Sintered Duplex Stainless Steels
Publication -
Sintered Duplex Stainless Steels Corrosion Properties
Publication -
Sintered Duplex Stainless Steels Corrosion Properties
Publication -
Hydrogen degradation of high strength weldable steels
PublicationW pracy przedstawiono wyniki badań podatności stali spawalnych o wysokiej wytrzymałości na niszczenie wodorowe. Badano dwa gatunki stali S690Q i ich złącza spawane. Ocenę podatności na niszczenie wodorowe wykonano przy różnych rodzajach obciążeń w środowisku wody morskej przy polaryzacji katodowej.
-
Measurements of the mechanical Barkhausen noise in ferromagnetic steels
PublicationArtykuł ten przedstawia wpływ zmian w mikrostrukturze stali P91, powstałych w skutek obróbki cieplnej, na właściwości mechanicznego efektu Barkhausena (MeBN). Parametry takie jak amplituda obwiedni napięcia skutecznego (RMS) MeBN oraz położenie maksimum tejże obwiedni porównywane są, pod kątem czułości na obróbkę cieplną materiału, z klasycznymi parametrami takimi jak pole koercji magnetycznej czy też twardość mechaniczna HV. Największą...
-
Wpływ azotowania jarzeniowego i laserowego nadtapiania na odporność kawitacyjną stali X5CrNi18-10
PublicationNierdzewne stale austenityczne charakteryzują się doskonałą odpornością korozyjną, aczkolwiek niskimi właściwościami mechanicznymi. W wielu przypadkach ogranicza to ich eksploatację w warunkach przemysłowych. Ponadto, nierdzewne stale austenityczne są wrażliwe na korozję lokalną w obecności jonów halogenkowych. Technologie materiałowe, które dają potencjalne możliwości otrzymywania korzystnego wpływu na właściwości mechaniczne...
-
Influence of the laser remelting parameters on the thickness of surface layers created on the stainless steel X5CrNi18-10
PublicationIn this work the surface of austenitic stainless steel type X5CrNi18-10 was treated by using laser. Laser remelting was done by means of laser MLT 2500 CO2 with different parameters of treatment: P - power beam (800 [W], 1000 [W], 1100 [W], 1200 [W]); v - scanning velocity (6 [mm/s], 7 [mm/s], 8 [mm/s]); diameter of laser beam (1.4 [mm], 1.6 [mm]). The influence of these parameters on the thickness and shape of layers in manufacturing...
-
Fracture Surface Topography Parameters for S235JR Steel Adhesive Joints After Fatigue Shear Testing
PublicationThis paper presents the experimental results of a study investigating the effect of holes and notches made on the overlap ends on the strength of adhesive joints. Single-lap joints made of S235JR steel sheets bonded with Araldite 2024-2 epoxy adhesive were tested. For comparative reasons, static shear strength tests and high-cycle fatigue strength tests were performed. Adhesive-filled joints having three holes, each with a diameter...
-
Cyclic deformation and fracture behaviour of additive manufactured maraging steel under variable-amplitude loading
PublicationThe cyclic deformation and fracture behaviour of 18Ni300 maraging steel produced by laser beam powder bed fusion is studied under variable-amplitude loading. The tests were conducted under fully-reversed strain-controlled conditions with a loading sequence comprising three ascending cycles and three descending cycles repeated sequentially until failure. After the tests, fracture surfaces were examined using height and volume surface...
-
Fracture Areas Quantitative Investigating of Bending-Torsion Fatigued Low-Alloy High-Strength Steel
PublicationIn this study, the impact of pseudo-random non-proportional bending-torsion fatigue loadings proportion on the fatigue life and the fracture surface topography was analyzed. Investigation was carried out for 24 specimens made of S355J2 steel with 11 different ratios of maximum stresses λ. For these cases, after the fatigue tests, the surface topography measurements were carried out using an optical profilometer, using the focus...
-
Experimental analysis of the behaviour of different types of joints in the steel structure model subjected to earthquake loading
PublicationThe present paper reports the results of the experimental study performed to investigate the behaviour of two different types of joints (destroyed and welded ones) in the model of the steel structure under seismic excitations. The structure was subjected to three earthquakes, namely Kobe, Loma Prieta and Northridge, using the shaking table investigation. The results obtained from the study...
-
Assessment of Corrosive Behaviour and Microstructure Characterization of Hybrid Friction Stir Welded Martensitic Stainless Steel
PublicationThis study examined the effect of induction heating on the microstructure and corrosion characteristics of hybrid friction stir welded AISI 410 stainless steel. Five joints have been produced with different friction stir welding parameters like welding speed, spindle speed, plunge depth, and induction power. Their microstructures were evaluated using a scanning electron microscope, and chemical composition was examined using...
-
Stress–strain model of lower corroded steel plates of normal strength for fitness-for-purpose analyses
PublicationThis study investigates the mechanical properties of specimens made of normal strength steel subjected to lower marine immersed corrosion degradation levels (below 25 %). The specimens were corroded in laboratory conditions, and only natural factors were controlled to raise the corrosion rate (reaching the level of 1 mm/year). Three different thicknesses of plates made of normal strength of shipbuilding steel are investigated (between...
-
Performance of Vector-valued Intensity Measures for Estimating Residual Drift of Steel MRFs with Viscous Dampers
PublicationViscous Dampers (VDs) are widely used as passive energy dissipation system for improving seismic performance levels especially in retrofitting of buildings. Residual Inter-story Drift Ratio (R-IDR) is another important factor that specifies the condition of building after earthquake. The values of R-IDR illustrates the possibility of retrofitting and repairing of a building. Therefore, this study aims to explore the vector-valued...
-
The features of steel surface hardening with high energy heating by high frequency currents and shower cooling
Publication -
Numerical Modeling of Steel Surface Hardening in the Process of High Energy Heating by High Frequency Currents
Publication -
High-temperature kinetics study of 430L steel powder oxidized in air at 600–850 °C
PublicationThe 430L stainless steel powder with a mean particle size of 95 μm was studied to determine its high-temperature oxidation properties. Continuous thermogravimetric measurements were carried out for 100 h in air at temperatures in the range of 600–850 °C. Even though a considerable amount of Cr (up to ˜5 wt.% Cr) inside the grains was depleted – especially inside small grains – no breakaway oxidation was observed. This indicates...
-
Assessment of technical condition and repair of steel structure elements on the example of fire damage in a warehouse building
PublicationThe paper analyses a case study on the structural assessment of warehouse building partially damaged by fire caused by external source (fire of lorries close to the building). The authors focus on the site investigations and laboratory test results prior to assessing actual condition of the structural elements. Both strengthening concept and repair procedure of a steel column are addressed here. A short literature survey in the...
-
The Influence of the Depth of Cut in Single-Pass Grinding on the Microstructure and Properties of the C45 Steel Surface Layer
PublicationThe paper contains the results of a metallographic examination and nanoindentation test conducted for the medium carbon structural steel with low content of Mn, Si, Cu, Cr, and Ni after its grinding to a depth ranging from 2 μm to 20 μm, at constant cutting speed (peripheral speed) of vs = 25 ms−1 and constant feed rate of vft = 1 m/min. Applied grinding parameters did not cause the surface layer hardening, which could generate...
-
Improvement of Performance Level of Steel Moment-Resisting Frames Using Tuned Mass Damper System
PublicationIn this paper, parameters of the tuned mass dampers are optimized to improve the performance level of steel structures during earthquakes. In this regard, a six-story steel frame is modeled using a concentrated plasticity method. Then, the optimum parameters of the Tuned Mass Damper (TMD) are determined by minimizing the maximum drift ratio of the stories. The performance level of the structure is also forced to be located in a...
-
Numerical Investigation on Dynamic Performance of a Multi-storey Steel Structure Model and Comparison with Experimental Results
PublicationShaking table testing is the most commonly adopted method to simulate earthquake forces. This approach allows us to analyze the dynamic performance and provides a valuable insight into the dynamics of building structures, which helps to improve their future safety and reliability. The present study aims to conduct a numerical evaluation of dynamic response of a multi-storey steel structure model, which was previously examined during...
-
Improved Performance of 1-Ethyl-3-Methylimidazolium Tetrafluoroborate at Steel/HCl Interface by Iodide Ions
PublicationThe corrosion and corrosion inhibition of St37 steel in 0.1 M HCl solution by 1-ethyl-3-methylimidazolium tetrafluoroborate (EMITFB) and the effect of addition of KI on the inhibitive performance of EMITFB have been examined by electrochemical [electrochemical impedance spectroscopy, potentiodynamic polarization, and dynamic electrochemical impedance spectroscopy (DEIS)] and surface examination [scanning electron microscope (SEM)...
-
Experimental research on over-laminated steel sandwich panel connection to determine the form of fatigue failure
PublicationThe novel means of transport need to meet rising both the economic and ecologic requirements. In recent years the International Maritime Organization (IMO) introduced new measure of ship energy efficiency (the EEDI index), as well as new regulations regarding higher quality of fuel (so called Tier limits). It resulted in much higher interest of the technological development of ships. One of the solution having great potential is...
-
EXPERIMENTAL AND NUMERICAL INVESTIGATION ON SPECIMEN GEOMETRY EFFECT ON THE CTOD VALUE FOR VL-E36 SHIPBUILDING STEEL
PublicationThere are special cases in the marine industry, where additional material tests, such as the fracture toughness test, must be performed. Additional fracture toughness tests, such as CTOD (Crack Tip Opening Displacement), are typically performed on three-point bend specimens. The dimension that defines all the specimen dimensions is the thickness of the material to be tested. It is recommended by classification societies (e.g. DNVGL)...