Filters
total: 1342
filtered: 1152
displaying 1000 best results Help
Search results for: STEEL STRUCTURESCTURE
-
Sintered Duplex Stainless Steels Corrosion Properties
Publication -
Hydrogen degradation of high strength weldable steels
PublicationW pracy przedstawiono wyniki badań podatności stali spawalnych o wysokiej wytrzymałości na niszczenie wodorowe. Badano dwa gatunki stali S690Q i ich złącza spawane. Ocenę podatności na niszczenie wodorowe wykonano w oparciu o próbę rozciągania z małą prędkością odkształcania w powietrzu i środowisku wody morskiej przy polaryzacji katodowej. Przedstawiono model niszczenia wodorowego badanych stali i ich złączy spawanych.
-
Hydrogen degradation of high strength weldable steels
PublicationW pracy przedstawiono wyniki badań podatności stali spawalnych o wysokiej wytrzymałości na niszczenie wodorowe. Badano dwa gatunki stali S690Q i ich złącza spawane. Ocenę podatności na niszczenie wodorowe wykonano przy różnych rodzajach obciążeń w środowisku wody morskej przy polaryzacji katodowej.
-
Hydrogen Damage in Superaustenitic 904L Stainless Steels
Publicationresults on the influence of hydrogen on corrosion resistance and of hydrogen embrittlement of 904L superaustenitic stainless steel were investigated. The cracking behavior was studied by performing a slow strain rate test in synthetic seawater under varying cathodic polarization conditions. The results showed that the steel’s plasticity varied with the applied cathodic current density. Significant reductions in ductility were found,...
-
Measurements of the mechanical Barkhausen noise in ferromagnetic steels
PublicationArtykuł ten przedstawia wpływ zmian w mikrostrukturze stali P91, powstałych w skutek obróbki cieplnej, na właściwości mechanicznego efektu Barkhausena (MeBN). Parametry takie jak amplituda obwiedni napięcia skutecznego (RMS) MeBN oraz położenie maksimum tejże obwiedni porównywane są, pod kątem czułości na obróbkę cieplną materiału, z klasycznymi parametrami takimi jak pole koercji magnetycznej czy też twardość mechaniczna HV. Największą...
-
IMPACT-TOUGHNESS INVESTIGATIONS OF DUPLEX STAINLESS STEELS
PublicationDuplex stainless steels are very attractive constructional materials for use in aggressive environments because of their several advantages over austenitic stainless steels. Duplex steels have excellent pitting and crevice corrosion resistance, are highly resistant to chloride stress-corrosion cracking and are about twice as strong as common austenitic steels. Better properties are associated with their microstructures consisting...
-
Dissimilar underwater wet welding of HSLA steels
PublicationThe high-strength low-alloy S460ML and S460N steels were chosen for underwater wet welding of dissimilar T-joints using covered electrodes. For improving the quality of joints, the temper bead welding (TBW) method was used. The application of TBW in pad welding conditions has been investigated earlier but the possibility of usage of this technique in welded joints was not analyzed. The main aim of the study was to check the influence...
-
Performance of Vector-valued Intensity Measures for Estimating Residual Drift of Steel MRFs with Viscous Dampers
PublicationViscous Dampers (VDs) are widely used as passive energy dissipation system for improving seismic performance levels especially in retrofitting of buildings. Residual Inter-story Drift Ratio (R-IDR) is another important factor that specifies the condition of building after earthquake. The values of R-IDR illustrates the possibility of retrofitting and repairing of a building. Therefore, this study aims to explore the vector-valued...
-
Construction and Validation of Simulation Models of Samples Made from 316L Steel by Applying Additive Technique
Publication -
Microstructural and Mechanical Properties of Novel Co-Free Maraging Steel M789 Prepared by Additive Manufacturing
Publication -
Modelling and parameter identification of steel–concrete composite beams in 3D rigid finite element method
Publication -
The features of steel surface hardening with high energy heating by high frequency currents and shower cooling
Publication -
Numerical Modeling of Steel Surface Hardening in the Process of High Energy Heating by High Frequency Currents
Publication -
Structural and Microhardness Changes After Turning of the AISI 1045 Steel for Minimum Quantity Cooling Lubrication
Publication -
SURFACE TEXTURE ANALYSIS AFTER BALL END MILLING WITH VARIOUS SURFACE INCLINATION OF HARDENED STEEL
Publication -
Optimisation of machining parameters during ball end milling of hardened steel with various surface inclinations
Publication -
Post-failure fracture surface analysis of notched steel specimens after bending-torsion fatigue
Publication -
Analysis of fracture roughness parameters of S355J2 steel and EN AW-2017A-T4 aluminium alloy
Publication -
A Study on Deformation According to Steel Constraints During Thick-Plate Fillet Welding and Line Heating
Publication -
Residual stresses distribution in long seam-welded offshore catenary riser of high-manganese steel
Publication -
Microscopic impact of creep damage incipience and development on the magnetic properties of ferromagnetic Cr-Mo steel
PublicationPokazano wyniki badań emisji magneto-akustycznej (EMA0 oraz magnetostrykcji dla stali P22 w stanie dostawy i po ekploatacji. Wyniki te pokazują, że maksimum EMA jest skorelowane z maksimum pochodnej magnetostrykcji. Badania morfologii wydzieleń w granicach ziarn i w ich wnętrzu potwierdzają tezę, iż te pierwsze są główną przyczyną zmniejszania natężenia EMA. Zaproponowano prosty model tłumaczący ilościowo funkcję zmian natężenia...
-
Influence of the laser remelting parameters on the thickness of surface layers created on the stainless steel X5CrNi18-10
PublicationIn this work the surface of austenitic stainless steel type X5CrNi18-10 was treated by using laser. Laser remelting was done by means of laser MLT 2500 CO2 with different parameters of treatment: P - power beam (800 [W], 1000 [W], 1100 [W], 1200 [W]); v - scanning velocity (6 [mm/s], 7 [mm/s], 8 [mm/s]); diameter of laser beam (1.4 [mm], 1.6 [mm]). The influence of these parameters on the thickness and shape of layers in manufacturing...
-
The determination of deformations and stresses of laser welds used for fatigue assessment of steel sandwich panel joints
PublicationPanele typu sandwich znajdują szerokie zastosowanie w wielu gałęziach przemysłu. W przypadku niektórych zastosowań wymagających ocenę ryzyka dużą rolę odgrywa ocena trwałości zmęczeniowej spoin laserowych paneli. W pracy prezentowane są metody wyznaczania lokalnych odkształceń i naprężeń w połączeniach spawanych w celu oceny trwałości zmęczeniowej według hipotez lokalnych naprężeń i odkształceń.
-
Finite-element analysis of a base-isolated multi-storey steel building under seismic motions
PublicationNumerical simulation of the seismic behaviour of a multi-storey steel building, both fixed-base and base-isolated, under the 1940 El Centro earthquake was performed in this paper. The analyzed 4-storey building was decoupled from the shaking ground with the Polymeric Bearings, which can be considered a proposal of a new seismic isolation system. It consists of rectangular-shaped blocks made of a specially prepared flexible polymeric...
-
Numerical Analysis of a Steel Frame Building with Soft-storey Failure under Ground Motion Excitation
PublicationThe aim of this paper is to show the results of a numerical analysis focused on the behaviour of multi-storey steel frame building that suffers from a soft-storey failure under ground motion excitation. A numerical model of the structure was created in FEM computer software and was exposed to an impact that would have been generated after a soft-storey failure due to falling of the upper floors. During the analysis, the whole structure...
-
Evaluation of porous ferritic Fe22Cr stainless steel for solid oxide fuel cells at high temperature
PublicationW pracy przedstawiono wyniki badań korozji stali Fe22Cr w wysokich temperaturach.
-
EXPERIMENTAL AND NUMERICAL INVESTIGATION ON SPECIMEN GEOMETRY EFFECT ON THE CTOD VALUE FOR VL-E36 SHIPBUILDING STEEL
PublicationThere are special cases in the marine industry, where additional material tests, such as the fracture toughness test, must be performed. Additional fracture toughness tests, such as CTOD (Crack Tip Opening Displacement), are typically performed on three-point bend specimens. The dimension that defines all the specimen dimensions is the thickness of the material to be tested. It is recommended by classification societies (e.g. DNVGL)...
-
Glass-ceramic sealants and steel interconnects: accelerated interfacial stability and reactivity tests at high temperature
PublicationHigh-temperature reactions between glass-ceramic sealants and Fe-Cr alloy interconnects may lead to the formation of undesirable phases, and consequently degradation of solid oxide fuel/electrolyser devices. In this work, three different glass-ceramic sealants (Na-containing, Ba-containing, Sr-containing compositions) and Fe22Cr stainless steel powders (raw and pre-oxidised) are considered in order to test their chemical reactivity...
-
Assessment of Corrosive Behaviour and Microstructure Characterization of Hybrid Friction Stir Welded Martensitic Stainless Steel
PublicationThis study examined the effect of induction heating on the microstructure and corrosion characteristics of hybrid friction stir welded AISI 410 stainless steel. Five joints have been produced with different friction stir welding parameters like welding speed, spindle speed, plunge depth, and induction power. Their microstructures were evaluated using a scanning electron microscope, and chemical composition was examined using...
-
Fracture Areas Quantitative Investigating of Bending-Torsion Fatigued Low-Alloy High-Strength Steel
PublicationIn this study, the impact of pseudo-random non-proportional bending-torsion fatigue loadings proportion on the fatigue life and the fracture surface topography was analyzed. Investigation was carried out for 24 specimens made of S355J2 steel with 11 different ratios of maximum stresses λ. For these cases, after the fatigue tests, the surface topography measurements were carried out using an optical profilometer, using the focus...
-
Experimental analysis of the behaviour of different types of joints in the steel structure model subjected to earthquake loading
PublicationThe present paper reports the results of the experimental study performed to investigate the behaviour of two different types of joints (destroyed and welded ones) in the model of the steel structure under seismic excitations. The structure was subjected to three earthquakes, namely Kobe, Loma Prieta and Northridge, using the shaking table investigation. The results obtained from the study...
-
Stress–strain model of lower corroded steel plates of normal strength for fitness-for-purpose analyses
PublicationThis study investigates the mechanical properties of specimens made of normal strength steel subjected to lower marine immersed corrosion degradation levels (below 25 %). The specimens were corroded in laboratory conditions, and only natural factors were controlled to raise the corrosion rate (reaching the level of 1 mm/year). Three different thicknesses of plates made of normal strength of shipbuilding steel are investigated (between...
-
Suspension and process parameters selection for electrophoretic deposition of Mn–Co spinel coating on steel interconnects
PublicationMetallic interconnect coatings, consisting of MnCo2O4 spinel, were effectively applied to Crofer 22 APU using the electrophoretic deposition (EPD) method in both H2O: ethanol and pure ethanol solvents. The primary goal of this method was to prevent chromium migration, minimize evaporation, and control the oxidation rate. The study aimed to assess the quality, adhesion, and thickness of the Mn–Co coating, with the objective of...
-
Cyclic deformation and fracture behaviour of additive manufactured maraging steel under variable-amplitude loading
PublicationThe cyclic deformation and fracture behaviour of 18Ni300 maraging steel produced by laser beam powder bed fusion is studied under variable-amplitude loading. The tests were conducted under fully-reversed strain-controlled conditions with a loading sequence comprising three ascending cycles and three descending cycles repeated sequentially until failure. After the tests, fracture surfaces were examined using height and volume surface...
-
Fracture Surface Topography Parameters for S235JR Steel Adhesive Joints After Fatigue Shear Testing
PublicationThis paper presents the experimental results of a study investigating the effect of holes and notches made on the overlap ends on the strength of adhesive joints. Single-lap joints made of S235JR steel sheets bonded with Araldite 2024-2 epoxy adhesive were tested. For comparative reasons, static shear strength tests and high-cycle fatigue strength tests were performed. Adhesive-filled joints having three holes, each with a diameter...
-
The Influence of the Depth of Cut in Single-Pass Grinding on the Microstructure and Properties of the C45 Steel Surface Layer
PublicationThe paper contains the results of a metallographic examination and nanoindentation test conducted for the medium carbon structural steel with low content of Mn, Si, Cu, Cr, and Ni after its grinding to a depth ranging from 2 μm to 20 μm, at constant cutting speed (peripheral speed) of vs = 25 ms−1 and constant feed rate of vft = 1 m/min. Applied grinding parameters did not cause the surface layer hardening, which could generate...
-
High temperature corrosion of steel equipment in modern rafinery environments with high and low sulphur content
PublicationPrzedstawiono charakterystykę i mechanizmy procesów wysokotemperaturowej korozji elementów ze stali we współczesnych rafineriach ropy naftowej podczas eksploatacji we frakcjach węglowodorowych o niskiej i wysokiej zawartości siarki. Zwrócono uwagę na procesy korozji siarkowej w obecności wodoru i bez obecności wodoru oraz proces pylenia metalu pod wpływem węgla ze środowiska - w wypadku niskiej zawartości siarki w środowisku.
-
Effect of the Post-Weld Surface Condition on the Corrosion Resistance of Austenitic Stainless Steel AISI 304
PublicationSurfaces of welded elements made of corrosion-resistant (stainless) steels develop temper colours. The removal of thickened oxide layers off steels exposed to temperatures below 300°C is necessary and entails the restoring of high corrosion resistance of the stainless steel. The article presents tests concerned with the effect of a method applied to remove post-weld temper on the corrosion resistance of austenitic stainless steel...
-
Experimental research on over-laminated steel sandwich panel connection to determine the form of fatigue failure
PublicationThe novel means of transport need to meet rising both the economic and ecologic requirements. In recent years the International Maritime Organization (IMO) introduced new measure of ship energy efficiency (the EEDI index), as well as new regulations regarding higher quality of fuel (so called Tier limits). It resulted in much higher interest of the technological development of ships. One of the solution having great potential is...
-
Numerical Investigation on Dynamic Performance of a Multi-storey Steel Structure Model and Comparison with Experimental Results
PublicationShaking table testing is the most commonly adopted method to simulate earthquake forces. This approach allows us to analyze the dynamic performance and provides a valuable insight into the dynamics of building structures, which helps to improve their future safety and reliability. The present study aims to conduct a numerical evaluation of dynamic response of a multi-storey steel structure model, which was previously examined during...
-
Improved Performance of 1-Ethyl-3-Methylimidazolium Tetrafluoroborate at Steel/HCl Interface by Iodide Ions
PublicationThe corrosion and corrosion inhibition of St37 steel in 0.1 M HCl solution by 1-ethyl-3-methylimidazolium tetrafluoroborate (EMITFB) and the effect of addition of KI on the inhibitive performance of EMITFB have been examined by electrochemical [electrochemical impedance spectroscopy, potentiodynamic polarization, and dynamic electrochemical impedance spectroscopy (DEIS)] and surface examination [scanning electron microscope (SEM)...
-
Application of wavelet transform in analysis of guided wave propagation signals for damage detection in a steel plate
PublicationThe paper presents results of experimental investigations on damage detection using guided wave propagation technique. The tested specimen was a steel plate with a defect in the form of a rectangular notch. Lamb waves were excited by a PZT actuator and sensed by a laser vibrometer. Since reflections from damage in registered signals are often masked by measurement noise, for identification of time of reflections from damage, continuous...
-
Influence of laser processing of the low alloy medium carbon structural steel on the development of the fatigue crack
PublicationThe paper contains the results of the structural analysis, hardness tests and fatigue tests conducted for the medium carbon structural steel with low content of Cr and Ni after its processing with CO2 laser beam. Pre-cracks were made in the round compact tension (RCT) specimen used for fatigue test. Next, four paths, parallel to each other, were melted on both sides of the samples using a laser beam. The paths were perpendicular...
-
Influence of separation gap on the response of colliding models of steel structures under seismic and paraseismic excitations
PublicationAs a result of high urbanization, the need to erect closely-spaced buildings forces designers to consider collisions between structures taking place during ground motions. Experimental and numerical studies have confirmed that such collisions (often referred to as structural pounding) may cause serious damage to the structural elements and even lead to total collapse of colliding structures. The main reason of earthquake-induced...
-
Assessment of technical condition and repair of steel structure elements on the example of fire damage in a warehouse building
PublicationThe paper analyses a case study on the structural assessment of warehouse building partially damaged by fire caused by external source (fire of lorries close to the building). The authors focus on the site investigations and laboratory test results prior to assessing actual condition of the structural elements. Both strengthening concept and repair procedure of a steel column are addressed here. A short literature survey in the...
-
THE COST ANALYSIS OF CORROSION PROTECTION SOLUTIONS FOR STEEL COMPONENTS IN TERMS OF THE OBJECT LIFE CYCLE COST
PublicationSteel materials, due to their numerous advantages - high availability, easiness of processing and possibility of almost any shaping are commonly applied in construction for carrying out basic carrier systems and auxiliary structures. However, the major disadvantage of this material is its high corrosion susceptibility, which depends strictly on the local conditions of the facility and the applied type of corrosion protection system....
-
Numerical investigation on dynamic performance of a multi-storey steel structure model and comparison with experimental results
PublicationShaking table testing is the most commonly adopted method to simulate earthquake forces. This approach allows us to analyze the dynamic performance and provides a valuable insight into the dynamics of building structures, which helps to improve their future safety and reliability. The present study aims to conduct a numerical evaluation of dynamic response of a multi-storey steel structure model, which was previously examined during...
-
High-temperature kinetics study of 430L steel powder oxidized in air at 600–850 °C
PublicationThe 430L stainless steel powder with a mean particle size of 95 μm was studied to determine its high-temperature oxidation properties. Continuous thermogravimetric measurements were carried out for 100 h in air at temperatures in the range of 600–850 °C. Even though a considerable amount of Cr (up to ˜5 wt.% Cr) inside the grains was depleted – especially inside small grains – no breakaway oxidation was observed. This indicates...
-
Preventing of earthquake-induced pounding between steel structures by using polymer elements – experimental study
PublicationPounding between two, or more, adjacent buildings during earthquakes has been identified as one of the reasons for substantial damage or even total collapse of colliding structures, so it has been the subject of numerous studies in the recent years. A major reason leading to interactions between adjacent, insufficiently separated structures results from the differences in their dynamic properties. A number of different methods...
-
Safety of erection and repair of steel tanks with geometric imperfections using heavylift jack-up system
PublicationSafety analysis is performed of cylindrical vertical steel tanks during erection using heavylift jack up system. During an assembly or repair process a set of hydraulic supports is used. It allows to use the in-place lifting of heavy steel constructions on the required height. Wind can strongly influence stability of the lifted tank. Any geometric imperfections can reduce the critical or limit load. In the work failures of the...