displaying 1000 best results Help
Search results for: PLAŻE PIASZCZYSTE
-
Heat transfer and pressure drop characteristics of the silicone-based plate heat exchanger
PublicationThe paper presents an experimental investigation of a silicone based heat exchanger, with passive heat transfer intensification by means of surface enhancement. The main objective of this paper was to experimentally investigate the performance of a heat exchanger module with the enhanced surface. Heat transfer in the test section has been examined and described with precise measurements of thermal and flow conditions. Reported...
-
Pressure drop related to flow maldistribution in a model minichannel plate heat exchanger
PublicationThe paper describes the issues related to the pressure drop that accompanies the phenomenon of maldistribution of working fluid between the channels of a model minichannel plate heat exchanger. The research concerns a single exchanger's plate containing 51 (in every geometry) parallel rectangular minichannels of hydraulic diameters 461 µm, 571 µm, 750 µm and 823 µm. In addition, the more complex geometry has been investigated,...
-
Random field modelling of mechanical behaviour of corroded thin steel plate specimens
PublicationThe objective of this work is to explore the possibility of corrosion degradation modelling of thin steel plate specimens with the use of random field approach. The mechanical properties are obtained via the nonlinear Finite Element Analysis with the use of an explicit dynamic solver. The fully nonlinear material model is adopted to obtain the proper stress-strain response. Sensitivity analysis considering the main statistical...
-
A general theory for anisotropic Kirchhoff–Love shells with in-plane bending of embedded fibers
PublicationThis work presents a generalized Kirchhoff–Love shell theory that can explicitly capture fiber-induced anisotropy not only in stretching and out-of-plane bending, but also in in-plane bending. This setup is particularly suitable for heterogeneous and fibrous materials such as textiles, biomaterials, composites and pantographic structures. The presented theory is a direct extension of classical Kirchhoff–Love shell theory to incorporate...
-
Flow visualization and heat transfer investigations on the flat plate with streamwise pressure gradient
PublicationPaper presents experimental investigations results for film cooling on a flat plate. The main objective of the design is the streamwise pressure distribution on the flat plate as in the blade cascade. The transient and steady-state technique with liquid crystals for the surface temperature distribution with film cooling has been used in experiments in a low speed wind tunnel.
-
Thermal performance of a prototype plate heat exchanger with minichannels under boiling conditions
PublicationTo solve the problem and to meet the requirements of customers in the field of high heat fluxes transfer in compact units, a new design of plate heat exchanger with minichannels (minichannels PHE) was proposed. The aim was to construct a compact heat exchanger of high effectiveness for the purpose of household cogeneration ORC system. In this paper the experimental analysis of an assembled prototype of such compact heat exchanger...
-
Bead-on-plate welding on S235JR steel by underwater local dry chamber process
PublicationThe article presents the results of the effect of parameters of underwater local dry chamber welding on the properties of padding welds. The effect of heat input and the type of shielding gas on the structure and hardness of welds was established. the functions for estimating the maximum hardness of the heat affected zone have been also elaborated.
-
Damage detection of a T-shaped panel by wave propagation analysis in the plane stress
PublicationW pracy zaprezentowano podejście obliczeniowe do analizy propagacji fal w płaskim stanie naprężenia. Problem brzegowo-początkowy podlega przestrzennej aproksymacji z użyciem wielowęzłowych, izoparametrycznych, czworobocznych elementów klasy C0. Macierze elementowe są całkowane numerycznie za pomocą kwadratury Gauss-Legendre-Lobatto. Aproksymację w dziedzinie czasu wykonano za pomocą algorytmu Newmarka. Symulacje numeryczne przeprowadzono...
-
Shaping Place Identity through Interaction on the Example of the European Solidarity Centre in Gdansk
PublicationThe article presents process of shaping place identity on the example of an important for Pomerania region investment - European Solidarity Centre. The realization of the European Solidarity Centre aims to be one of the essential elements of shaping Gdańsk’s identity of space. The article is an attempt to analyse how the presence of realization gradually affects the formation of the place identity of new urban space. Analysis...
-
Shell model of multiple-row moment I-section end-plate joint
PublicationThe paper deals with a problem of application of shell elements in the models of multiple-row moment end-plate connections. The extended connection of I-section with a cross-section W760x265x220 made of steel S355 was analyzed. Comparison analysis of FEM, complex volume and shell models has been done. Three cases with different end-plate thickness: 14, 18 and 36 mm were analyzed and compared with the reference results. Comparison...
-
Numerical simulation of damage detection in rectangular plate by two-dimensional wavelet transform.
PublicationW pracy przedstawiono metodę lokalizacji pęknięć w płytach przy zastosowaniu transformaty falkowej.
-
Effect of fabric anisotropy on shear localization in sand during plane strain compression
PublicationW artykule przedstawiono wyniki numerycznej wpływu anizotropii strukturalnej w materiałach granulowanych na powstawanie lokalizacji odkształceń. Obliczenia wykonano dla ściskania w płaskim stanie odkształcenia stosując metodę elementów skończonych na bazie mikropolarnego modelu hipoplastycznego.
-
The role and the place of method validation in the Quality Assurance and Quality Control (QA/QC) System
PublicationOznaczanie analitów na coraz niższych poziomach stężeń w próbkach charakteryzujących się coraz bardziej złożonym składem matrycy to jeden z głównych kierunków rozwojowych analityki chemicznej. Jest to zadanie niezwykle trudne i skomplikowane, w związku z czym stanowi wielkie wyzwanie dla analityków i wymaga zwrócenia uwagi na problem kontroli i zapewnienia jakości uzyskiwanych wyników (ang. Quality Assurance/Quality Control - QA/QC).W...
-
The Late Neolithic sepulchral and ritual place of site 14 in Kowal (Kuyavia, Central Poland)
Publication -
Comparison of resonance optical scattering of plane waves by infinite gratings of silver cylinders and strips
Publication -
The Effect Of Reference Plane On Values Of Areal Surface Topography Parameters From Cylindrical Elements
Publication -
Neuro-wavelet damage detection technique in beam, plate and shell structures with experimental validation
PublicationNiniejsza praca poświęcona jest technice diagnostyki konstrukcji bazującej na transfor-macie falkowej oraz sztucznych sieciach neuronowych (tzw. system neuro-wavelet). Zastosowanie analizy falkowej pozwala na lokalizację uszkodzeń wymagającą mini-malnej ilości danych wejściowych. W tym celu niezbędna jest tylko odpowiedź kon-strukcji pomierzona w wielu punktach. Poprawę efektywności lokalizacji zniszczeń uzyskano poprzez użycie...
-
Fluoride content in the hair in dependence of the place of residence, sex, dietary habits and anthropometric data
Publication -
The Role of and the Place of Method Validation in the Quality Assurance and Quality Control (QA/QC) System
Publication -
Application of Navigated Ultrasound for Assessment of the Anterior Pelvic Plane in Patients With Degenerative Hip Diseases
Publication -
Buckling and postcritical behaviour of the elastic infinite plate strip resting on linear elastic foudation
PublicationW pracy rozważa się problem von Karmana dla swobodnie podpartego pasma płytowego spoczywającego na sprężystym podłożu i poddanego równomiernie rozłożonemu obciążeniu ściskającemu na krawędzi podparcia. Krytyczne wartości parametrów wyznaczono na podstawie problemu zlinearyzowanego. Stan pokrytyczny badano za pomocą redukcji Liapunowa-Schmidta i twierdzenia Crandalla-Rabinowitza. Wykazano, że istnieje maksymalna częstość fal w kierunku...
-
A new method for searching optimal path on a raster plane including cost of direction changes
PublicationArtykuł przedstawia nowy algorytm znajdowania optymalnych tras na siatkach rastrowych. Szczegółowo opisano zastosowane struktury danych, dzięki który algorytm ma liniową złoŻoność obliczeniową. Zamieszczono również propozycje możliwych zastosowań.
-
Damage location in beam and plate structures by wavelet analysis of experimentally determined mode shapes
PublicationArtykuł dotyczy zastosowania analizy falkowej do lokalizacji uszkodzeń w konstrukcjach belkowych i płytowych. Wykonano testy dynamiczne belki wspornikowej i płyty utwierdzonej wzdłuż jednej z krawędzi. Lokalizację defektu otrzymano za pomocą transformaty falkowej eksperymentalnie wyznaczonych postaci drgań.
-
The simultaneous detection of food dyes from different samples in a 96-well plate by spectrophotometry
Publication -
Significant Parameters Identification for Optimal Modelling of the Harp-Type Flat-Plate Solar Collector
Publication -
The influence of the place of residence, smoking and alcohol consumption on bone mineral content in the facial skeleton
Publication -
Investigations of hydraulic jump configured by a two phase air water jetimpinging on a flat plate.
PublicationPrzedstawiono wyniki badań eksperymentalnych uskoku hydraulicznego powstającego przy napływie strugi uderzającej na powierzchnię płaskiej płyty.
-
Torque Transmitted by Multi-plate Wet Clutches in Relation to Number of Friction Plates and Their Dimensions
PublicationIn the paper results of experimental tests on multi-plate wet clutch torque capacity for various diameters and numbers of friction plates are presented. Construction of an apparatus for laboratory tests of wet clutch engagement, drag torque and maximum torque is shown. Methodology of maximum torque capacity experiment and hydraulic circuit diagram, which supplies a motor and an actuator for the experiment are described. Analytically...
-
M-integral for finite anti-plane shear of a nonlinear elastic matrix with rigid inclusions
PublicationThe path-independent M-integral plays an important role in analysis of solids with inhomogeneities. However, the available applications are almost limited to linear-elastic or physically non-linear power law type materials under the assumption of infinitesimal strains. In this paper we formulate the M-integral for a class of hyperelastic solids undergoing finite anti-plane shear deformation. As an application we consider the problem...
-
Comprehensive exploration of technological tensioning effects in welded thin plate girders: an in-depth investigation
PublicationThin-walled plate girders are widely used in structures and construction due to their effectiveness in transferring loads. The permanent deformations of the girder lead to a lack of stability, which necessarily leads to its replacement. Replacing permanently deformed thin-walled load-bearing structures requires large financial outlays. Technological prestressing is one of the most effective methods for studying and treating permanent...
-
Influence of the Widespread Use of Corten Plate on the Acoustics of the European Solidarity Centre Building in Gdansk
PublicationThis paper describes the relationship between a strong architectural vision that is difficult to balance, and user expectations in terms of acoustics. The focus is on the use of corten steel as the dominant finishing material on façades and interiors to achieve an expressive, symbolic message through program-based design. The architectural premises justifying the adopted solutions are presented, especially the universality and...
-
Guided wave propagation in debonding detection in CFRP-reinforced steel plate-like structures
PublicationThe present study investigates the guided wave propagation in multilayered steel specimens reinforced with carbon fiber reinforced polymer (CFRP) through theoretical, numerical, and experimental means. The effectiveness of externally bonded reinforcement (EBR) relies heavily on the bonding quality between the CFRP and the substrate. Premature debonding, a prevalent and hazardous defect, can arise from suboptimal manufacturing processes,...
-
Determination of stepped plate thickness distribution using guided waves and compressed sensing approach
PublicationGuided waves recently have attracted significant interest as a very promising research area. The signals registered by a specially designed sensor network are processed to assess the state of the tested structure. Despite the constant development of novel damage detection algorithms employing guided waves, the phenomenon of wave propagation still needs detailed recognizing and understanding for the further progress of non-destructive...
-
Application of twin-plane ECT sensor for identification of the internal imperfections inside concrete beams
PublicationThe main purpose of this paper is to investigate application of special construction of Electrical Capacitance Tomography (ECT) sensor to concrete beams internal homogeneity tests. Identification of internal imperfection inside the concrete beams is one of the main problems related to analysis of the construction structure bearing capacity. Therefore, this paper shows attempts to study the measurement prospects for this non-invasive,...
-
Moment resistance of I-section end-plate roof girder splices; a case study
PublicationThis article deals with the problem of determining the resistance of end-plate connections. A nonlinear FEM model of the joint was constructed in order to predict its carrying capacity. A standard code procedure was done as well. The analyses have been done to assess atypical end-plate joints designed and constructed as a part of roof structures.
-
Heat transfer in plate heat exchanger channels: experimental validation of selected correlation equations
PublicationThis study is focused on experimental investigation of selected type of brazed plate heat exchanger. The Wilson approach was applied in order to estimate heat transfer coefficients for the PHEx passages. The main aim of the paper was to experimentally check ability of several correlations published in the literature to predict heat transfer coefficients by comparison experimentally obtained data with appropriate predictions. The...
-
The use of plate springs for preloading of a system of tapered roller bearings of a wind turbine gearbox
PublicationThe use of preloaded tapered roller bearings in wind turbine drive systems allows a transfer of load in the case of high variations of axial forces. The examined bearing system, a modification of a current design, consists of a pair of different sized bearings. Previous study showed the high sensitivity of tapered roller bearings on the existing radial interference. Dimensional tolerances used in the original design do not allow...
-
On Anti-Plane Surface Waves Considering Highly Anisotropic Surface Elasticity Constitutive Relations
PublicationWithin the framework of highly anisotropic surface elasticity model we discuss the propagation of new type of surface waves that are anti-plane surface waves. By the highly anisotropic surface elasticity model we mean the model with a surface strain energy density which depends on incomplete set of second derivatives of displacements. From the physical point of view this model corresponds to a coating made of a family of parallel...
-
Anti-plane surface waves in media with surface structure: Discrete vs. continuum model
PublicationWe present a comparison of the dispersion relations derived for anti-plane surface waves using the two distinct approaches of the surface elasticity vis-a-vis the lattice dynamics. We consider an elastic half-space with surface stresses described within the Gurtin–Murdoch model, and present a formulation of its discrete counterpart that is a square lattice half-plane with surface row of particles having mass and elastic bonds different...
-
Comparison of anti-plane surface waves in strain-gradient materials and materials with surface stresses
PublicationHere we discuss the similarities and differences in anti-plane surface wave propagation in an elastic half-space within the framework of the theories of Gurtin–Murdoch surface elasticity and Toupin–Mindlin strain-gradient elasticity. The qualitative behaviour of the dispersion curves and the decay of the obtained solutions are quite similar. On the other hand, we show that the solutions relating to the surface elasticity model...
-
THE EFFECT OF ALTERNATIVE CUTTER PATHS ON FLATNESS DEVIATIONS IN THE FACE MILLING OF ALUMINUM PLATE PARTS
PublicationIn this paper the relationships between the alternative machining paths and flatness deviations of the aluminum plate part, were presented. The flatness tolerance of the main surface of the plate part has crucial meaning due to the assembly requirement of piezoelectric elements on the radiator. The aluminum bodies under investigation are the base part of the radiators with crimped feathers for the train industry. The surface of...
-
Anti-plane shear waves in an elastic strip rigidly attached to an elastic half-space
PublicationWe consider the anti-plane shear waves in a domain consisting of an infinite layer with a thin coating lying on an elastic half-space. The elastic properties of the coating, layer, and half-space are assumed to be different. On the free upper surface we assume the compatibility condition within the Gurtin–Murdoch surface elasticity, whereas at the plane interface we consider perfect contact. For this problem there exist two possible...
-
Four-Port Circulator Using Reduced Ground Plane Ferrite Coupled Line Junction
PublicationIn this paper the investigations of four-port circula-tor using longitudinally magnetized ferrite coupled line section are presented. The device is designed by cascading ferrite section with magic-T junction ensuring its even and odd mode excitation. The scattering parameters of ferrite coupled line junction are calculated using own software and verified with the use of commercial software. The even and odd excitation of ferrite...
-
Heat transfer in plate heat exchanger channels: experimental validation of selected correlation equations
PublicationThis study is focused on experimental investigation of selected type of brazed plate heat exchanger. The Wilson approach was applied in order to estimate heat transfer coefficients for the PHEx passages. The main aim of the paper was to experimentally check ability of several correlations published in the literature to predict heat transfer coefficients by comparison experimentally obtained data with appropriate predictions. The...
-
Influence of the position of the swash plate rotation axis on the volumetric efficiency of the axial pistons pumps
PublicationThe article describes the influence of the position of the swash plate axis of rotation on the size of the dead space and the volumetric efficiency of the axial pistons pump. Superposition of the two motions have been proposed - the rotation of the swash plate with respect to axis intersecting the axis of rotation of the pump shaft and the shifts of swash plate yielding a result of the rotation axis offset effect. In the article...
-
Unusual dynamic properties of water near the ice-binding plane of hyperactive antifreeze protein
PublicationThe dynamical properties of solvation water of hyperactive antifreeze protein from Choristoneura fumiferana (CfAFP) are analyzed and discussed in context of its antifreeze activity. The protein comprises of three well-defined planes and one of them binds to the surface of ice. The dynamical properties of solvation water around each of these planes were analyzed separately; the results are compared with the dynamical properties...
-
Analysis of electromagnetic plane wave scattering from 2-d periodic arrangements of posts
PublicationArtykuł prezentuje metodę analizy rozpraszania fali elektromagnetycznej od układu periodycznie rozłożonych obiektów cylindrycznych na płaszczyźnie. Opisywane podejście analizy wykorzystuje pełnofalowe rozwiązanie oparte na metodzie dopasowania rodzajów. Wynikiem analizy jest wielorodzajowa macierz rozproszenia badanych powierzchni periodycznych.
-
Bionic relations as features of the author’s original concept of biomorphic plastic forms that belong to a place
PublicationThe article concerns the search for an architectural formula for living organically in the area of Pojezierze Kaszubskie [the Kashubian Lake Dis- trict]. The original project consisted in creating a series of biomorphic plastic forms that belong to the place. In this way, a set of alternative solutions was created in the form of small clay sculptures that account for bionic relationships between the newly created cultural elements...
-
Bakterie z rodziny Enterobacteriaceae w wodzie i piasku plaży w Sopocie.
PublicationW pracy przedstawiono fragment wyników badań dotyczących oceny jakości mikrobiologicznej przybrzeżnych wód i osadów piaszczystych wybrzeża Zatoki Gdańskiej oraz wybranych potoków do niej uchodzących. Prezentowane wyniki dotyczą liczby i składu gatunkowego bakterii Enterobacteriaceae w wodach przybrzeżnych i piasku.
-
Place identity in socialist-modernist building
Open Research DataThe data include 96 individual response of falowiec's residents on the following scales (1) social identification, (2) falowiec’s place identity (3) interest in history of place. Each line represents responses obtained from one participant and his or her demographic characteristics. like gender, age, and education level.