Search
Search results for: rubberised asphalt
-
Analiza temperatury ekwiwalentnej do projektowania nawierzchni asfaltowych w Polsce z wykorzystaniem metody AASHTO 2004
PublicationW artykule przedstawiono analizę temperatury ekwiwalentnej obliczanej w oparciu o kryterium spękań zmęczeniowych warstw asfaltowych z metody AASHTO 2004 oraz kryterium deformacji strukturalnych Instytutu Asfaltowego. Do obliczeń przyjęto konstrukcję nawierzchni KR5 oraz wykorzystano dane temperaturowe z 50 stacji meteorologicznych z okresu 30 lat od roku 1989 do roku 2019 włącznie udostępnione przez Instytut Meteorologii i Gospodarki...
-
Determination of binder-aggregate adhesion by contact angle measurement
PublicationThe key factor in asphalt pavement durability, especially in the presence of water, is adhesion of the bituminous binder to mineral aggregates. There are currently no standard laboratory test procedures that can quickly and accurately measure the strength of the interaction (bond) between the binder and aggregate. In this regard, to evaluate the adhesion force measurements based on the contact angle between the binder and the aggregate...
-
Pomiar wartości opóźnienia hamowania dla sprawnego i niesprawnego układu hamulcowego
PublicationW artykule przedstawiono wyniki badań: sprawny układ hamulcowy i niesprawny układ hamulcowy. Pomiary opóźnienia hamowania przeprowadzono na suchej nawierzchni asfaltowej. Wykonano układ, który rozszczelnia przewód hamulcowy przy przednim prawym kole w czasie jazdy. Wykonano symulację wycieku płynu hamulcowego
-
Przegląd nanododatków stosowanych w warstwach asfaltowych nawierzchni drogowych
PublicationJednym z kierunków rozwoju technologii materiałowych jest nanotechnologia rozumiana jako dziedzina zajmująca się zastosowaniem nanododatków do wytwarzania nowych materiałów oraz ich wpływem na parametry modyfikowanych materiałów. W ostatnich latach nanotechnologia wkracza do technologii modyfikacji asfaltów stosowanych w nawierzchniach drogowych. W artykule przedstawiono stosowane obecnie w budownictwie drogowym nanododatki oraz...
-
Bitumen Aging—Laboratory Simulation Methods Used in Practice and Selected Directions of Research on New Methods
PublicationChanges in the properties of bitumen binders that occur as a result of aging have a huge impact on the durability of products produced from them. In particular, asphalt pavements, which constitute the most common use of petroleum bitumen, are susceptible to damage resulting from the increasing stiffness of the bitumen during its life cycle. Increased stiffness of asphalt pavements reduces the pavement resistance to low-temperature...
-
Poroelastic Road Surfaces - State of The Art
PublicationPoroelastic Road Surfaces (PERS) constitute a specific group of pavements containing a great amount of crumbled rubber. In most cases rubber aggregate constitutes about 20% of the mixture (by weight) and a polyurethane resin is used as a binder. As a result, PERS is characterized by a much higher elasticity than asphalt and a high porosity typical for drainage pavements. Due to this, tire/road noise is greatly reduced and on top...
-
ANALIZA PORÓWNAWCZA DROGI HAMOWANIA MOTOCYKLA Z WŁĄCZONYM I WYŁĄCZONYM UKŁADEM ABS
PublicationW artykule przedstawiono wyniki pomiaru drogi hamowania motocykla przy użyciu hamulca koła przedniego, koła tylnego oraz kombinacji obu tych hamulców. Próby intensywnego hamowania motocykla przeprowadzono na suchej nawierzchni asfaltowej z włączonym i wyłączonym układem ABS. Na podstawie zmierzonej drogi hamowania dokonano obliczenia średniego opóźnienia hamowania.
-
Nowoczesne nawierzchnie asfaltowe.
PublicationW referacie omówiono kilka wybranym zagadnień, a mianowicie: nowe metody projektowania nawierzchni, nawierzchnie długowieczne, asfalt drenażowy, asfalt spieniony i problemy ze współczesnymi nawierzchniami w Polsce. Przedstawiono zalety i wady omawianych rozwiązań oraz możliwości ich zastosowań w Polsce.
-
Review and evaluation of cold recycling with bitumen emulsion and cement for rehabilitation of old pavements
PublicationThe article presents Polish experience with cold recycling of asphalt pavements with theusage of bituminous emulsion and cement. In the 1990s numerous roads in Polandrequired immediate reinforcement due to their significant degradation. Implementation ofthe cold recycling technology was one of the solutions to this problem. Cold recycledmixtures containebeside the recycled asphalt pavement and aggregateetwo differenttypes of binding...
-
Aspects of intergranular corrosion of AISI 321 stainless steel in high-carbon-containing environments
PublicationPurpose – The purpose of this paper is to present a case study of unexpected sensitization to intergranular corrosion of highly resistant AISI 321 steel in petrochemical conditions, where it was subjected to the simultaneous influence of elevated temperature of 250°C and vapors from the asphalt production process. Design/methodology/approach – Corrosion coupons were exposed in an installation carrying asphalt vapors. To identify...
-
Mariusz Jaczewski dr inż.
People -
Preliminary study of linear viscoelasticity limits of cold recycled mixtures determined in Simple Performance Tester (SPT)
PublicationThe publication presents methodology developed for determination of linear viscoelasticity limits for cold recycled mixtures with cement and bituminous emulsion using Simple Performance Tester (SPT). Methodology was verified on reference materials (PCV and steel dummy specimens, cement concrete and asphalt concrete) to comply with elasticity and viscoelasticity theory. The developed methodology enabled determination of linear viscoelasticity...
-
Ecobitumen Ecological bitumen
ProjectsProject realized in Department of Process Engineering and Chemical Technology from 2020-11-20
-
Avariâ stal'nogo rezervuara s dvojnoj stenkoj dlâ hraneniâ gorâčih produktov
PublicationPodano analizę przyczyn awaryjnych deformacji dwupłaszczowego zbiornika na asfalt magazynowany w temp. +200 C
-
Consideration of dynamic loads in the determination of axle load spectra for pavement design
PublicationAxle load spectra constitute a crucial part of the data for pavement design and pavement distress analysis. Typically, axle load spectra represent static load from vehicles and do not include dynamic loads generated by vehicles in motion. While dynamic loads can significantly contribute to faster pavement distress, this fact is mostly omitted in pavement design methods. The paper presents a methodology for consideration of dynamic...
-
The Effect of Flexible Pavement Mechanics on the Accuracy of Axle Load Sensors in Vehicle Weigh-in-Motion Systems
PublicationWeigh-in-Motion systems are tools to prevent road pavements from the adverse phenomena of vehicle overloading. However, the effectiveness of these systems can be significantly increased by improving weighing accuracy, which is now insufficient for direct enforcement of overloaded vehicles. Field tests show that the accuracy of Weigh-in-Motion axle load sensors installed in the flexible (asphalt) pavements depends on pavement temperature...
-
Determination of equivalent axle load factors with the use of strain energy of distortion
PublicationThe paper proposes a new method for calculation of equivalent axle load factors based on the analysis of strain energy of distortion induced in road pavements by traffic loads. The main advantage of the method is the more accurate calculation of the effects of multiple axles and super single versus dual tyres. The methodconsiders the location of critical points, at which strain energy of distortion reaches extreme values. When...
-
Design of poroelastic wearing course with the use of direct shear test
PublicationPoroelastic Road Surfaces (PERS) are characterized by porous structure with at least 20% of air void content and stiffness almost 10 times lower than typical asphalt course. Such properties enable noise reduction up to 12 dB in comparison to SMA 11 mixture. However, the main disadvantage of previously used poroelastic mixtures, based on resin type binders, was their low durability, which resulted in raveling and delamination from...
-
Wpływ stopnia dewulkanizacji odpadów gumowych na wybrane właściwości modyfikowanego asfaltu drogowego
PublicationW niniejszej publikacji przedstawiono wyniki badań wpływu warunków dewulkanizacji odpadów gumowych na wybrane właściwości asfaltów drogowych, co umożliwia charakterystykę oddziaływań asfalt-dewulkanizat.
-
Wpływ zbrojenia polimerowymi włóknami rozproszonymi na wybrane właściwości mieszanek mineralno-asfaltowych
PublicationW artykule przedstawiono wybrane wyniki badań mieszanek mineralno-asfaltowych zbrojonych polimerowymi włóknami rozproszonymi. Ocenie poddano mieszankę włókien zbrojących aramidowo-poliolifenowych pod kątem wpływu ich zastosowania na właściwości niskotemperaturowe i odporności na deformacje trwałe mieszanek mineralno-asfaltowych. Właściwości niskotemperaturowe oceniano na podstawie testu zginania próbek belkowych oraz na podstawie...
-
The selected roof covering technologies in the aspect of their life cycle costs
PublicationIn the article is presented an analysis of the life cycle costs calculation for selected roof coverings. The scope of research includes costs of construction, maintenance and demolition of the roof covering structure for two alternative technologies – the traditional and new generation. On the presented example of an industrial building with a roof area of 1000 m², the above costs are taken to consideration for the roof covering...
-
Strain-dependent behaviour of cold recycled material mixtures in cyclic compression tests
PublicationThe purpose of the study is to evaluate strain-dependent behaviour of Cold Recycled Material (CRM) mixtures using three frameworks typically applied for Hot Mix Asphalt (HMA): linear viscoelastic (LVE) limits; non-linearity directions; changes in rheological model parameters. To this aim, the complex modulus of three CRM mixtures with different bitumen-to-cement ratio (0.2, 0.6 and 1.8) was measured in cyclic compression mode,...
-
Radar technique in application of interlayer identification connections
PublicationOne of important issues in pavement construction is to ensure that layers applied directly one on top of the other make up a continuous whole and form an integral construction complex. An appropriate interlayer connection plays here significant role ensuring proper transmission of distortions generated by wheels of vehicles to lower layers and preventing water penetration between the layers. In case of damaged pavements where lack...
-
Investigation of low-temperature cracks on selected national roads and motorways in Poland 2020
Open Research DataThe dataset contains video investigation and records of 68 road sections in various parts of Poland. Videos were recorded with the use of two cameras: 1) mounted in front of measurement vehicle, which was focused on overall view of road and 2) which was focused on pavement surface. The records are categorized according to the ID of the section given...
-
Tragfähigkeitsminderung durch lokale Instabilität bei stählernen Zylindertanks mit Doppelmantel
PublicationOmówiono zagrożenie stateczności i nosności płaszczy i den zbiorników dwupłaszczowych w tym także zbiorników na ciecze magazynowe w wysokiej temperaturze (asfalt magazynowany w temparaturze +200 C. Rozważania teoretyczne odniesiono do sytuacji awaryjnych które wystąpiły w praktyce.
-
Polish experience with cold in-place recycling
PublicationDeep cold in-place recycling using cement and asphalt emulsion has been used for reconstruction of existing roads since the beginning of the 1990s. This paper describes the first Polish requirements for mineral-cement-emulsion mixtures. As requirements stated for the strength of the mineral-cement-emulsion mixtures were quite high, most of the mixtures were designed using high amount of cement and aggregate added for the improvement...
-
Recycled Polyethylene terephthalate (PET) as Construction Material in Civil Engineering: A Review
PublicationIn general, the quantity of plastics of all types consumed annually all over the world has been growing in a phenomenal way. The manufacturing processes, service industries and municipal solid wastes (MSW) generate numerous waste plastic materials. The increasing awareness about the environment has tremendously contributed to the concerns related with disposal of the generated wastes. It is believed that the management of solid...
-
BINDER COURSES USING COLD RECYCLED MIXTURES – A NOVEL CONCEPT IN COLD RECYCLING
PublicationCold recycling with cement and bituminous emulsion is one of the most environmentally friendly techniques to maximize the reuse of reclaimed asphalt (RA) collected during demolition of roads. Cold recycled mixtures are commonly used for base courses in construction or rehabilitation of flexible and semi-rigid pavements. Current experiences demonstrated that cold recycling with appropriate requirements and technical recommendations...
-
The Application of Granulated Expanded Glass Aggregate with Cement Grout as an Alternative Solution for Sub-Grade and Frost-Protection Sub-Base Layer in Road Construction
PublicationThe purpose of the research was to assess the possibility of using granulated expanded glass aggregate (GEGA) with cement grout as a replacement of a sub-grade and frost-protection layer, made of natural fine aggregates (NATU), stabilized with a hydraulic binder. Instead of traditional parts of the road construction, such as the sub-grade and frost-protection layer with the application of fine aggregate, stabilized with cement,...
-
Quantifying the effective mobilized RAP content during hot in-place recycling techniques
PublicationThe utilization of in-place recycling techniques is capable of consuming 100% reclaimed asphalt pavement (RAP). Hot in-place recycling (HIR) is one of the promising techniques to rehabilitate the pavements suffering from minor cracking issues through heat scarification, additive injecting, mechanical mixing, and compacting. However, the main concern of using 100% RAP in HIR remains as how much RAP can be activated and mobilized...
-
Noise measurements on low noise pavements - problems with inhomogeneity of wearing course
PublicationDuring the last several years, when performing numerous CPX noise measurements on low noise pavements,significant inhomogeneity of the wearing course was observed in numerous cases. Similar problems were almost not existing regarding to the dense pavements.In general three main reasons of inhomogeneity can be defined. The first one are imperfections in technology of production of a asphalt mix or/and errors made already during...
-
Initial Field Validation of Poroelastic Pavement Made with Crumb Rubber, Mineral Aggregate and Highly Polymer-Modified Bitumen
PublicationTire/road noise in most driving conditions dominates other sources of traffic noise. One of the most efficient ways of reducing tire/road noise is to use the so-called “low noise pavement”. According to numerous studies, at present, poroelastic road pavement that is composed of rubber and mineral aggregate and polyurethane or bituminous binder gives the best noise reduction up to 12 dB. Unfortunately, there are many problems with...
-
Wpływ termoplastycznych kompozycji napełnianych miałem gumowym na wybrane właściwości asfaltu drogowego
PublicationDynamiczny rozwój transportu samochodowego zmusza do wykonywania nawierzchni drogowych z materiałów o wysokiej wytrzymałości oraz odporności na odkształcenia trwałe, co znacznie wydłuża żywotność nawierzchni. Polskie przedsiębiorstwo BISEK Sp. z o.o. z Wrocławia we współpracy z Politechniką Wrocławską, jako pierwsze wykorzystało miał gumowy do modyfikacji asfaltów metodą mokrą. W chwili obecnej firma Lotos Asfalt Sp. z o.o. wprowadziła...
-
Biological hazards in low noise, poroelastic road surfaces
PublicationDrainage pavements as well as poroelastic pavements ("PERS") are a very efficient way to decrease traffic noise by reducing tire/road noise at the source as well as noise propagation over the road surface. Many noise generating mechanisms at the tire/road interface are very much reduced by road porosity (pipe resonance, "air pumping", Helmholtz resonance and the horn effect). A well-designed porous or poroelastic road surface may...
-
The Use of Direct Shear Test for Optimization of Interlayer Bonding Under a Poroelastic Layer
PublicationPoroelastic Road Surfaces (PERS) are characterised by porous structure with air void content of 20% or higher and stiffness almost 10 times lower than that of a standard asphalt course. Such properties enable noise reduction by up to 12 dB in comparison to SMA 11 mixture. However, the disadvantage of a poroelastic pavement is its low durability, which partially results from delamination from the lower layer. The paper aims to investigate...
-
Neufunde von fossilen Harzen aus dem Mitteldeutschen Braunkohlenrevier
PublicationEs werden einige Neufunde von fossilen Harzen aus ded tertiaren Braunkohlenvorkommen Mitteldeutschlands aus Sachsen-Anhalt vorgestellt. Die Fundstucke wurden mit dem Vergleichsmaterial der Harzammulung des Geiseltalmuseums in Halle/Saale und den privaten Harzsammlungen von G. Krumbiegiel und R. Wimmer makropetrographisch verglichen. Sie werden erstmalig beschrieben und die Ergebnisse der Infrarotabsorptions-Spektroskopie prasentiert.
-
Mieszanki mineralno-asfaltowe na ciepło - przegląd dodatków
PublicationObecnie, stosowane są różne strategie przy budowie dróg w celu minimalizowania negatywnego wpływu na środowisko naturalne. Jedną z ostatnich technologii są ''mieszanki na ciepło'', które skutkują obniżeniem temperatury produkcji i układania. Ten efekt może być osiągnięty dwoma sposobami: przez zastosowanie dodatków do lepiszcza lub mieszanki zmniejszających lepkość asfaltu lub przez dodanie niewielkiej ilości wody, która spienia...
-
Polish experience of dynamic tests for bored piles
PublicationPrzedstawiono zastosowanie badań dynamicznych, DLT, do oceny nośności wierconych pali wielkośrednicowych.Na podstawie badań terenowych, dla dwóch obiektów mostowych, wykonano badania dynamiczne (DLT) oraz korelacyjne badania statyczne (ASPLT). Określono pełną krzywą osiadania. Uzyskano dobrą zgodność krzywych obciążenie - osiadanie dla zakresu obciążeń roboczych.
-
Evaluation and application of data from road weather stations for winter maintenance management
PublicationThe paper presents the analysis of road weather data from meteorological stations located at the Polish national roads of Pomerania District during the impact of winter conditions. Presented issue is particularly important from the point of view the problem of winter maintenance and especially for prediction and assurance of quality of asphalt pavement surface ie. resistance to low temperature cracking or risk of glazed frost....
-
Impact of optimization of ALS point cloud on classification
PublicationAirborne laser scanning (ALS) is one of the LIDAR technologies (Light Detection and Ranging). It provides information about the terrain in form of a point cloud. During measurement is acquired: spatial data (object’s coordinates X, Y, Z) and collateral data such as intensity of reflected signal. The obtained point cloud is typically applied for generating a digital terrain model (DTM) and a digital surface model (DSM). For DTM...
-
High frequency impulse ground penetrating radar application in assessment of interlayer connections
PublicationGround Penetrating Radar (GPR) technique is commonly used in the nondestructive evaluation of pavement structures. In particular, this method is used to estimate thicknesses of pavement layers as well as it can be utilized in advanced studies of pavement structures. The device presented in this paper comprise the high frequency impulse antennas that allow for investigating the interlayer zones in terms of their electromagnetic...
-
The long-term properties of mineral-cement-emulsion mixtures
PublicationThis publication presents evaluation of long-term behavior of mineral-cement-emulsion (MCE) mixtures. MCE mixtures are among the major products of cold recycling of old asphalt pavements. They are composed by binding of the old materials reclaimed from the pavement and new mineral aggregate using two different binding agents – cement and bituminous emulsion. While bituminous emulsion dissolutes and binds materials quite fast, it...
-
Linear viscoelastic transversely isotropic model based on the spectral decomposition of elasticity tensors
PublicationThe linear viscoelasticity is still a useful model in the engineering for studying the behavior of materials loaded with different loading rates (frequencies). Certain types of materials reveal also an anisotropic behavior: fiber reinforced composites, asphalt concrete mixtures, or wood, to name a few. In general, researchers try to identify experimentally the dependence of engineering constants like: directional Young’s moduli...
-
Tyre/road noise reduction by a poroelastic road surface
PublicationLow noise road surfaces of existing types may in favourable cases and in new conditions provide up to 7 dB of noise reduction. For higher noise reductions, innovative solutions must be sought. Poroelastic road surfaces (PERS) may be such a solution, which currently is studied in the EU project PERSUADE. This paper presents results of trials with a PERS version prefabricated by one of the project partners. Tests were made in a laboratory...
-
Investigation method of large-volume tire with mobile test rig
PublicationThe goal of this research is to develop the tire test method and mobile tire test rig. The test rig enables measurement of tire properties as stiffness and viscous damping in vertical direction, and tire–ground characteristics on the asphalt rigid surface. The tire-ground characteristics are measured by force and a torque measurement hub. The design, calibration and the algorithm for calculating the forces in the wheel center are...
-
Stiffness of cold-recycled mixtures under variable deformation conditions in the IT-CY test
PublicationStiffness modulus belongs to the most important properties describing the cold-recycled mixtures (CRM) in terms of their usability in road pavement structures. Previous research proved that this property is strongly dependent on the scheme and conditions of the test (temperature and time of loading) and the time that has passed since the compaction of the specimen or pavement layer. It is a result of the influence of two different...
-
The application of non-destructive methods in the diagnostics of the approach pavement at the bridges
PublicationThe article presents the possibility of using non-destructive methods of road pavement diagnostics as an alternative to traditional means to assess the reasons for premature cracks adjacent to bridge objects. Two scanning methods were used: laser scanning to measure geometric surface deformation and ground penetrating radar (GPR) inspection to assess the road pavement condition. With the use of a laser scanner, an effective tool...
-
Advancing sustainable hybrid bitumen systems: A compatibilization solution by functionalized polyolefins for enhanced crumb rubber content in bitumen
PublicationPolymer waste pollution has a profound effect on the environment and, consequently, on the lifestyle of hu- mankind. The massive production and disposal of cross-linked polymers clearly exemplify the challenges of recycling. Increasing efforts are being undertaken to introduce recycled polymers, especially crumb rubber (CR), into asphalt formulations. Due to the rather poor processability and phase separation associated with CR- modified...
-
Inhomogeneity of low-noise wearing courses evaluated by tire/road noise measurements using the close-proximity method
PublicationPerforming numerous analyses of tire/road noise measurements on low-noise pavements during the last several years, the authors observed significant inhomogeneity of the wearing course in numerous cases, while similar problems were almost non-existent when dense pavements were measured. Three main causes of low-noise pavement inhomogeneity can be defined. The first one is imperfections in the technology used for asphalt mix production...
-
Application of dynamic headspace and gas chromatography coupled to mass spectrometry (DHS-GC-MS) for the determination of oxygenated volatile organic compounds in refinery effluents
PublicationThe paper presents a new procedure for the determination of oxygenated volatile organic compounds (O-VOCs) in postoxidative effluents from the production of petroleum asphalt using dynamic headspace coupled to gas chromatography-mass spectrometry in the selected ion monitoring (SIM) mode (DHSGC-MS). Among the GC capillary columns tested, a polar SLB-IL111 column with the ionic liquid stationary phase was found to be superior due...