Search results for: BI5TI3FEO15 CERAMICS
-
Influence of synthesis conditions on glass formation, structure and thermal properties in the Na 2 O-CaO-P 2 O 5 system doped with Si 3 N 4 and Mg
PublicationOxynitride phosphate glasses and glass-ceramics were prepared using new synthesis routes for phosphate glasses. Materials were melted from pre-prepared glass samples in the system Na-Ca-P-O with addition of Mg and/or Si3N4 powders under different preparation conditions. The melting process was conducted at 1000–1500 °C either under air or nitrogen atmosphere to obtain materials with different nitrogen content. Their topography...
-
Nano-particle doped hydroxyapatite material evaluation using Spectroscopic Polarization Sensitive Optical Coherence Tomography
PublicationBio-ceramics such as hydroxyapatite (HAp) are widely used materials in medical applications, especially as an interface between implants and living tissues. There are many ways of creating structures from HAp like electrochemical assisted deposition, biomimetic, electrophoresis, pulsed laser deposition or sol-gel processing. Our research is based on analyzing the parameters of the sol-gel method for creating thin layers of HAp....
-
Proton-Electron Hole Interactions in Sr(Ti,Fe)O3−δ Mixed-Conducting Perovskites
PublicationOxides in which total electrical conductivity is determined by the partial conductivities of three types of charge carriers i.e. holes/ electrons, oxygen ions, and protons are key components of well-functioning proton ceramic fuel cells. Apart from electrochemical properties also easily modified microstructure is an important feature of the electrodes. In the paper, a group of SrTi1−xFexO3−δ (STF, x = 0.2–0.8) perovskites prepared...
-
Paweł Wierzba dr hab. inż.
PeopleDr Paweł Wierzba, E.E. M.Sc. E.E. received from WETI PG 1994 PhD in optoelectronics (with honours) from WETI PG 2001 Research Stays at VTT Technical Research Centre of Finland from 1997 to 2000 Finnish Academy Scholarship at VTT Technical Research Centre of Finland (12 months) 2002-3 Research interest area covers optical and optical fiber meaurement methods, technology of selected ceramic and liquid crystalline materials relevant...
-
Aleksandra Dorota Mielewczyk-Gryń dr hab. inż.
People -
Ammonium Hydroxide Mediated Hydrothermal Crystallization of Hydroxyapatite Coatings on Titanium Substrate
Publication -
Piotr Jasiński prof. dr hab. inż.
PeoplePiotr Jasinski obtained MSc in electronics in 1992 from the Gdansk University of Technology (GUT), Poland. Working at GUT, he received PhD in 2000 and DSc in 2009. Between 2001 and 2004 Post Doctoral Fellow at Missouri University of Science and Technology, while between 2008 and 2010 an Assistant Research Professor. Currently is an Associate Professor at Gdansk University of Technology working in the field of electronics, biomedical...
-
Nagniatanie ślizgowe stali hartowanej Cf53 kulkami ceramicznymi
PublicationCeramika techniczna dostępna na rynku a stosowana na ostrza skrawające mogłaby być używana również na elementy robocze narzędzi nagniatających. Duża twardość tych materiałów jest korzystna natomiast inne właściwości fizyczne w tym parametry struktury geometrycznej powierzchni powodują, że nie zawsze są właściwym materiałem na elementy robocze w procesie nagniatania materiałów hartowanych. W tym artykule przedstawiono wyniki badań...
-
Nanocrystallization as a tool for controlling in vitro dissolution of borophosphate glass
PublicationThe controlled nanocrystallization of sodium-calcium-borophosphate glass (Na16.6Ca5.1B10.5Al0.8P10.5 O56.5 in at %) was conducted to investigate its influence on in vitro dissolution. Three temperatures (570 ◦C, 590 ◦C, and 610 ◦C) were selected based on thermal analysis and investigation of the morphology, structure, and in vitro dissolution of glass and glass-ceramics was conducted. The results of X-ray diffraction confirmed...
-
Development of conductive porous media as packing materials for biotrickling filter – microbial fuel cell system (BTF-MFC system)
Open Research DataDataset presents values of electrical resistance measured for three developed conductive packimg materials for the application in a BTF-MFC system.
-
Polymer derived SiOC/Sn nanocomposites from a low-cost single source precursor as anode materials for lithium storage applications
PublicationMetal- based materials capable of lithium (Li) alloy formation are key to realization of the next generation of high-energy density anodes for Li-ion batteries, owing to their high storage capacity. Designing a good sup- porting matrix is essential for homogeneously nesting these metallic nanodomains, to effectively utilize their high capacity while tackling the volume expansion issues. Silicon oxycarbides (SiOC), obtained via...
-
Peculiarities associated with testing polyetheretherketone (PEEK) in a model rolling contact
PublicationPolyetheretherketone (PEEK) was investigated using a modified version of the four-ball tester in which the upper forth ball was replaced by a cone in such a way that kinematics of the four-ball configuration were fully preserved. Rotation of the cone enforced orbiting and rolling of the ceramic balls around the polymer cup. The results produced some unexpected peculiarities in the wear of ceramic balls which, in principle, should...
-
Mariusz Deja dr hab. inż.
PeopleAssistant Professor in the Department of Manufacturing Engineering and Automation. He graduated in 1993, obtaining Master degree at the Faculty of Mechanical Engineering, Gdańsk University of Technology in the field of study: Mechanical Engineering, specialization: Technological Process Design. After graduation he worked for the Department of Manufacturing Engineering and Automation and his main research area was associated with...
-
Processing and thermal characterization of polymer derived SiCN(O) and SiOC reticulated foams
Publication -
Cold sintering of colloidal silica particles using different alkali solutions
Publication -
Direct synthesis of fine boron carbide powders using expanded graphite
Publication -
Thermal stability of expanded perlite modified by mullite
Publication -
Correlations of structural, thermal and electrical properties of sodium doped complex borophosphosilicate glass
Publication -
Influence of Ni ion site occupancy on laser induced third harmonic generation (THG) studies in Li2SO4–MgO–P2O5 amorphous system
Publication -
Methodical engineering of defects in MnXZn1-X O(x = 0.03, and 0.05) nanostructures by electron beam for nonlinear optical applications: A new insight
Publication -
Fe3O4/graphene oxide/Fe4[Fe(CN)6]3 nanocomposite for high performance electromagnetic interference shielding
Publication -
Dielectric and electrical properties of synthesized PBGO/Fe3O4 nanocomposite
Publication -
Ultraviolet to near-infrared down-conversion in Bi3+–Yb3+ co-doped YAM phosphor
Publication -
Effects of electrophoretic deposition times and nanotubular oxide surfaces on properties of the nanohydroxyapatite/nanocopper coating on the Ti13Zr13Nb alloy
PublicationLoad-bearing implants are developed with a particular emphasis placed on an application of ceramic hydroxyapatite coatings in order, to enhance the bioactivity of titanium implants and to shorten the healing time. Therefore, thin, fully crystalline coatings that are, highly adhesive, hydrophilic and demonstrating antibacterial properties are ly looked for. The aim of this research was to develop and characterize the properties...
-
In-situ Cu-doped MnCo-spinel coatings for solid oxide cell interconnects processed by electrophoretic deposition
PublicationThe Cu doping of the Mn–Co spinel is obtained “in-situ” by electrophoretic co-deposition of CuO and Mn1.5Co1.5O4 powders and subsequent two-step reactive sintering. Cu-doped Mn1.5Co1.5O4 coatings on Crofer22APU processed by electrophoretic co-deposition method are tested in terms of long term oxidation resistance and area specific resistance tests up to 3600 h. The introduction of Cu in the spinel lead to higher level of densification...
-
Praseodymium substituted lanthanum orthoniobate: Electrical and structural properties
PublicationThe results of ionic transport and structural measurements for the lanthanum orthoniobate doped by praseodymium are presented and discussed. The influence of calcium co-doping on these properties has also been analyzed. The results suggest the predominant protonic conductivity for the investigated system in the whole range of investigated temperatures. The influence of calcium co-doping on phase purity is analyzed.
-
Effects of solution composition and electrophoretic deposition voltage on various properties of nanohydroxyapatite coatings on the Ti13Zr13Nb alloy
PublicationThe purpose of the research was to establish the influence of the solution composition and the electrophoretic deposition voltage on the coating homogeneity and thickness, nanohardness, adhesion, corrosion resistance and wettability. The Ti13Zr13Nb alloy was coated by the electrophoretic technique with hydroxyapatite in a solution containing 0.1, 0.2 or 0.5 g nanoHAp in 100 mL of suspension and at voltage 15, 30 or 50 V. The scanning...
-
High temperature monoclinic-to-tetragonal phase transition in magnesium doped lanthanum ortho-niobate
PublicationMagnesium doped lanthanum ortho-niobate (La0.98Mg0.02NbO4) was prepared by the molten salt synthesis method. X-ray diffraction and dilatometry methods were used to study high temperature behavior of the ceramic material. Special attention was paid to the phase transition between the monoclinic and tetragonal phases. The values of spontaneous strain on the basis of unit cell parameter, obtained by Rietveld refinement, have been...
-
Electrophoretic deposition (EPD) of nanohydroxyapatite - nanosilver coatings on Ti13Zr13Nb alloy
PublicationTitanium and its alloys are the biomaterials most frequently used in medical engineering, especially as parts of orthopedic and dental implants. The surfaces of titanium and its alloys are usually modified to improve their biocompatibility and bioactivity, for example, in connection with the deposition of hydroxyapatite coatings. The objective of the present research was to elaborate the technology of electrophoretic deposition...
-
Protective properties of Al2O3 + TiO2 coating produced by the electrostatic spray deposition method
PublicationMechanical resistance of Al2O3 + TiO2 nanocomposite ceramic coating deposited by electrostatic spray deposition method onto X10CrAlSi18 steel to thermal and slurry tests was investigated. The coating was produced from colloidal suspension of TiO2 nanoparticles dispersed in 3 wt% solution of Al2(NO3)3, as Al2O3 precursor, in ethanol. TiO2 nanoparticles of two sizes, 15 nm and 32 nm, were used in the experiments. After deposition,...
-
Effect of plasma sprayed and laser re-melted Al2O3 coatings on hardness and wear properties of stainless steel
PublicationCommercially available austenic stainless steel substrate was coated with commercially available, raw Al2O3 powder applied by means of plasma spraying method and then re-melted with CO2 laser beam of various parameters. Tribological and mechanical properties of the 120 J/mm and 160 J/mm laser re-melted coatings were compared with the tribological and mechanical properties of the “as-sprayed” coating. The influence of the laser...
-
Heat capacities and thermodynamic properties of antimony substituted lanthanum orthoniobates
PublicationThe results of heat capacity measurements for the lanthanum orthoniobate substituted with 10, 20 and 30 mol% of antimony (LaNb0.9Sb0.1O4, LaNb0.8Sb0.2O4 and LaNb0.7Sb0.3O4) are presented and discussed. Temperature dependence of low temperature heat capacity was analyzed within the Debye and Einstein models. The Debye temperature decreased, whereas the Einstein temperature increased with antimony content. The decrease of the Debye...
-
Characterization of magnesium doped lanthanum orthoniobate synthesized by molten salt route
PublicationMolten salt synthesis method has been used to prepare the single phase magnesium doped lanthanum orthoniobate. The phase composition has been checked by X-ray diffraction method and the microstructure studies have been performed by scanning electron microscopy. The high temperature properties of the material have been investigated by thermogravimetry and electrochemical impedance spectroscopy. A dependence between sample total...
-
Influence of Antimony Substitution on Spontaneous Strain and Thermodynamic Stability of Lanthanum Orthoniobate
PublicationThe analysis of the antimony substitution influence on temperature dependence of unit cell distortion has been done. The values of spontaneous strain and Landau order parameter for three different antimony contents varied had been calculated. The phase transition occurring for antimony substituted lanthanum orthoniobate was found to be second order. The high temperature solution calorimetry method has been used to investigate...
-
Ultrafast high-temperature sintering (UHS) of cerium oxide-based compound
PublicationUltrafast high-temperature sintering (UHS) is an innovative sintering technique that can densify ceramics in a few seconds, dramatically reducing the carbon footprint and firing costs. In this work, the feasibility of applying UHS in Gd-doped ceria (GDC) and GDC-Er-stabilized bismuth oxide (ESB) composite powders was investigated. At high UHS currents (22-24 A), a fully dense GDC sample with a large grain size was obtained. Nonetheless,...
-
New trifunctional acrylic water-based paint with self-cleaning, biocidal and magnetic properties
PublicationIn the present study, we report the synthesis and application of ZnFe2O4/SiO2-TiO2 nanocomposites with nonstoichiometric content of Fe to Zn used for the first time for the preparation of new generation trifunctional paints with self-cleaning, biocidal and magnetic properties. Currently, there are no compositions on the market for obtaining protective coatings in the form of paint, which simultaneously exhibit biocidal, magnetic...
-
Influence of hydrogen on a nanocrystalline high-entropy oxide with application potential in hydrogen technologies
PublicationThe influence of hydrogen on a (Co0⋅2Cu0⋅2Mg0⋅2Ni0⋅2Zn0.2)O HEO with a rock salt structure was studied. Two forms of this HEO (nanopowder and sinter) were prepared via mechanochemical synthesis (MS) and additional heat treatment, respectively. The chemical stability of the synthesized samples in a pure hydrogen atmosphere was investigated using Sievert’s technique. High-pressure hydrogenation at 250 ◦C had no noticeable effect...
-
Effects of La0.8Sr0.2MnO3 and Ag electrodes on bismuth-oxide-based low-temperature solid electrolyte oxygen generators
PublicationIn this study, La0.8Sr0.2MnO3 (LSM) was used as the ceramic electrode in a (Bi1.50Y0.50)0.98Zr0.04O3+δ (BYO)-based solid electrolyte oxygen generator (SEOG) and its performance was compared with that of a previously studied high-fire Ag electrode. Among La0.6Sr0.4Co0.2Fe0.8O3, LaNi0.6Fe0.4O3, Cu1.4Mn1.6O4, and LSM materials, only LSM materials did not trigger any chemical reaction or interdiffusion with BYO at temperatures up to...
-
Correlations of structural, thermal and electrical properties of sodium doped complex borophosphosilicate glass
PublicationBorophosphosilicate glasses with varying sodium ion concentrations were investigated for their, structural, thermal, and electrical properties. All the obtained glasses were transparent except the glass with the highest sodium content, which exhibited translucency due to inhomogeneities. Increasing sodium content led to reduced boron and silicon content while maintaining a constant B/Si ratio, indicating progressive depolymerization...
-
Self-supporting LSFO films for bolometers made with LTCC technology
PublicationOpisano metodę wytwarzania przewodzących, tlenkowych warstw ceramicznych tlenków lantanowo-strontowo żelazowych (LSFO) technologią low temperature co-fired ceramics (LTCC). Przedstawiono rezultaty pomiarów parametrów warstw pod kątem przydatności do produkcji detektorów IR.
-
Increasing the conductivity of V2O5-TeO2 glass by crystallization: structure and charge transfer studies
PublicationIn the present paper, V 2 O 5 -TeO 2 glass was prepared by the melt-quenching technique. Crystallization of glass with a vanadium content higher than 35%mol results in an increase in electrical conductivity by a few orders of magnitude and a decrease in activation energy from ~0.40 to ~0.12 eV. In this work, a critical review of existing charge transfer models was presented on the example of V 2 O 5 -TeO 2 glass and glass–ceramics....
-
Samonośne warstwy LSFO na bolometry wykonane technologią LTCC
PublicationOpisano sposób produkcji ceramicznych, przewodzących warstwtypu perowskitu z niestechiometrycznych tlenków lantanowo-strontowo żelazowych (LSFO) wykonanych technologią LTCC )low temperature co-fired ceramics). Zaprezentowano pomiary parametrów tych warstw, charakteryzujących ich przydatność do produkcji bolometrów.
-
Badanie właściwości czujników wilgotności na bazie nanocząstek tlenku cynku
PublicationW celu pomiaru wilgotności szeroko stosowane są czujniki elektryczne. Warstwą czynną, zmieniającą swoje właściwości pod wpływem pary wodnej, stanowią najczęściej materiały ceramiczne lub polimerowe. Tlenek cynku jest jednym z materiałów ceramicznych będących dobrym kandydatem do zastosowania go jako warstwy czynną w czujnikach wilgotności. W tej pracy przedstawiono wyniki badań właściwości struktur czujnikowych z warstwą tlenku...
-
Study of Phase and Chemical Composition of Bi1-xNdxFeO3 Powders Derived by Pressureless Sintering
PublicationIn the present paper studies on Bi1xNdxFeO3 for x =0.1-0.4 are reported. The mixed oxide method followed with pressureless sintering was employed for ceramics fabrication. Thermal behavior of stoichiometric mixtures of simple oxide powders, viz. Bi2O3, Nd2O3 and Fe2O3 was studied by simultaneous thermal analysis. It was found that with an increase in neodymium content the weight loss increased from 0.75% to 3.16% for x =0.1 and...
-
Bioactive core material for porous load-bearing implants
PublicationSo far state of knowledge on biodegradable materials is reviewed. Among a variety of investigated materials, those composed of polymers and ceramics may be considered as only candidates for a core material in porous titanium alloy. The collagen and chitosan among natural polymers, polyhydroxy acids among synthetic polymers, and hydroxyapatite and tricalcium phosphate among ceramics are proposed for further research. Three essential...
-
Materiały ceramiczne w łożyskach ślizgowych
PublicationOpisano obszary zastosowań ceramiki maszynowej w węzłach ślizgowych maszyn. Przedstawiono rodzaje ceramiki stosowane w łożyskowaniu ślizgowym. Przedstawiono produkowane fabrycznie ceramiczne łożyska ślizgowe.
-
Optymalizacja warunków pracy grubowarstwowych bolometrów LSFO
PublicationOpisano sposób produkcji bolometrów wykorzystujących ceramiczne, przewodzące warstwy typu perowskitu z niestechiometrycznych tlenków lantanowo-strontowo żelazowych (LSFO) wykonanych technologią LTCC (Low Temperature Co-fired Ceramics). Zaprezentowano wyniki pomiarów parametrów tych bolometrów oraz pozwalające na wybór optymalnych warunków pracy.
-
Effect of chemical composition on corrosion and wear behaviour of the composite Ni-Fe-Al2O3 coatings.
PublicationPrzedstawiono wyniki badań powłoki kompozytowej otrzymanej przez osadzanie katodowe galwaniczne w roztworze zawierającym sole niklu, żelaza oraz cząstki ceramiki Al2O3 o różnej wielkości i stężeniu. Wykazano, że charakterystyka ceramiki posiada wpływ na szybkość korozji i zużycia ściernego. W szczególności, zawartość ceramiki wpływa dodatnio na odporność na zużycie ścierne, ale nieco obniża odporność na zużycie korozyjne.
-
Barium boron aluminum silicate glass system for solid state optical gas sensors
PublicationRecent increasing demand for new eco-friendly materials and for low cost fabrication process for use in optical sensors field, raise concern about alternative materials for this application. We have designed two glass-ceramics compositions from the quaternary ROAl2O3- SiO2-B2O3(R=Ba) alkali-earth aluminum silicate system, labeled B72 and B69, with high refractive index (>1.6), large values of Abbe number (94.0 and 53.0, respectively),...
-
Gigantic electro-chemo-mechanical properties of nanostructured praseodymium doped ceria
PublicationSome oxygen defective fluorites are non-Newnham electrostrictors, i.e., the electromechanical response does not depend on their dielectric properties. Here, we show gigantic electrostriction in nanocrystalline 25 mol% praseodymium doped ceria (PCO) bulk ceramics. The material was fabricated with a fieldassisted spark plasma sintering (SPS) process from high-purity nanoscale PCO powders (<20 nm). The SPS process consolidates the...