Filters
total: 1610
displaying 1000 best results Help
Search results for: thermostable polymers
-
EFFECT OF ANTIOXIDANTS ON THE STABILITY OF PITCH- BASED POLYMER TO THERMO-OXIDATIVE ACTION
PublicationThe influence of stabilizers – hydrogen donors – on the processes of thermooxidative destruction of pitch-based polymer has been investigated. It is shown that Irganox has not stabilizing effect on pitch-based polymer and melamine slightly retards the destructive process. A mixture of melamine and Irganox exhibits synergetic stabilizing effect and at the optimum ratio it can be used to prevent unwanted thermooxidative processes...
-
Investigation of energy deposition and its optical imaging in polymer gel dosimeters
PublicationThis following chapter describes methods for verifying the absorbed dose during radiotherapy. Special attention is paid to the method using polymer-gel dosimeters, the dose reading of which is performed by means of Laser Computed Tomography. The chapter also includes considerations on alternative solutions for dosimetric measurements and various types of radiotherapy and their pros and cons. In addition, both the methods of structural...
-
Characteristics of Hybrid Bioglass-Chitosan Coatings on the Plasma Activated PEEK Polymer
Publication -
Effect of low-temperature plasma on chitosan-coated PEEK polymer characteristics
Publication -
Application of non-metal doped titania for inverted polymer solar cells
PublicationDomieszkowany jodem oraz domieszkowany jodem ditlenek tytanu uzyto jako warstwę buforową w ogniwie ITO/X-TiO2?P3HT-PCMB /MnO2/ Ag.Warswty X-TiO2 nalożono metodą spin-coatingu z zawiesiny nanocząstek w DMSO. Jednorodne struktury scharakteryzowane pod względem morfologii mikroskopowo metodą AFM. Charakterystyka prądowo-napięciowa urzdzeń wskazuje iż domieszkowany jodem TiO2 pozwala osiągnąć lepsze parametry PCE (1,67%) i prąd zwarcia...
-
Construction and investigation of SO2 amperometric sensor with a solid polymer electrolyte membrane
Publicationn this paper a sensor for detection of the sulphur dioxide based on three electrode cell configuration with a liquid electrolyte, a mercury sulphate reference electrode and a solid polymer electrolyte working electrode is presented. Working elec- trode was obtained by using Takenaka-Torikai chemical deposi- tion method by precipitation of Au particles into the pores of the Nafion membrane. Sensors characteristics measurements were...
-
Polarization interferometer using a Liquid Crystalline Polymer waveplate for wavelength measurement
PublicationA two-beam polarization interferometer for measuring wavelength changes of a tunable semiconductor laser was designed, built and tested. This interferometer uses a λ/8 waveplate made from Liquid Crystalline Polymer in order to generate two output signals in quadrature. The λ/8 waveplate can be manufactured either on a beamsplitter face or on the mirror surface, reducing the cost and complexity of the optomechnical assembly. Experiment...
-
The effect of macro polymer fibres length and content on the fibre reinforced concrete
PublicationThe paper presents studies of a ready-mix concrete containing polymer fibres of three different lengths: 24, 38 and 54 mm. The performed tests allowed to determine the effect of fibre volume fraction and length on the concrete strength. The basic parameters of concrete mixture (consistency, air content and bulk density) were identified. Fibre reinforced concrete belongs to a group of composite materials. The polymer fibres are...
-
Influence of the Addition of Recycled Aggregates and Polymer Fibers on the Properties of Pervious Concrete
PublicationThe aim of the study was to check the possibility of reusing aggregate from recycled concrete waste and rubber granules from car tires as partial substitution of natural aggregate. The main objective was to investigate the effects of recycled waste aggregate modified with polymer fibers on the compressive and flexural strength, modulus of elasticity and permeability of pervious concrete. Fibers with a multifilament structure and...
-
Polimeros-Ciencia e Tecnologia
Journals -
PROGRESS IN POLYMER SCIENCE
Journals -
JOURNAL OF POLYMER RESEARCH
Journals -
JOURNAL OF POLYMER ENGINEERING
Journals -
Antibacterial properties of laser-encapsulated titanium oxide nanotubes decorated with nanosilver and covered with chitosan/Eudragit polymers
PublicationTo provide antibacterial properties, the titanium samples were subjected to electrochemical oxidation in the fluoride-containing diethylene glycol-based electrolyte to create a titanium oxide nanotubular surface. Afterward, the surface was covered by sputtering with silver 5 nm film, and the tops of the nanotubes were capped using laser treatment, resulting in an appearance of silver nanoparticles (AgNPs) of around 30 nm in diameter...
-
New devices to capture the temperature effect under dynamic compression and impact perforation of polymers, application to PMMA
Publication -
Spatially Resolved Degradation in Heterophasic Polymers From 1D and 2D Spectral–Spatial ESR Imaging Experiments
Publication -
Benzene-induced hydro(solvo)thermal synthesis of Cu2+ and Zn2+ coordination polymers based on 1,3-benzenedicarboxylate
PublicationHydro(solvo)thermal reactions of Cu(NO3)2·2.5H2O or Zn(NO3)2·6H2O with 1,3-H2bdc provided two structurally different coordination polymers; a 2D network “metallacalixarene” based on the paddlewheel-type cluster with the formula [Cu(1,3-bdc)·H2O]·H2O (1) and a 3D framework [Zn(1,3-bdc)] (2), respectively. The use of a base was unnecessary in this synthesis; however, the presence of benzene played a crucial role in the crystallization...
-
Preparation and characterization of dummy-template molecularly imprinted polymers as potential sorbents for the recognition of selected polybrominated diphenyl ethers
PublicationThe main aim of this work was to conduct the preliminary/basic research concerning the preparation process of a new dummy molecularly imprinted polymer (DMIP) materials. Developed DMIPs were proposed as a sorption material in solid-phase extraction (SPE) technique for recognition of selected low mass polybrominated diphenyl ethers (PBDEs) e PBDE-47 and PBDE-99. Four new DMIPs were synthesized employing bulky polymerization technique...
-
Thermal, spectroscopic and luminescence investigations of lanthanide(III) coordination polymers based on V-shaped 4,4′-sulfonyldibenzoic acid
Publication -
Zn(II) and Cd(II) coordination polymers with tri-tert-butoxysilanethiol and bipyridines. Synthesis, crystal structure and spectroscopy
PublicationTrzy nowe silanotiolany cynku(II) I kadmu(II) [Zn{SSi(OtBu)3}2(μ-bpea) •CH3CN]n 1, [Cd{SSi(OtBu)3}2(μ -bpea) •2CHCl3]n 2 oraz [Cd{SSi(OtBu)3}2(μ -bpey)•C7H8]n 3 otrzymane z użyciem pochodnych bipirydylu [bpea = 1,2-bis(4-pyridyl)etan and bpey = 1,2-bis(4-pyridyl)etylen] zostały zsyntetyzowane i strutkualnie scharakteryzowane przy użyciu rentgenografii strukturalnej XRD. Ich budowa krystaliczna została dodatkowo potwierdzona przy...
-
One dimensional coordination polymers generated from Cd(II) tri-tert-butoxysilanethiolates and flexible aliphatic diamines.
PublicationPraca ta dotyczy chemii koordynacyjnej tri-tert-butoksysilanotiolanu kadmu(II) z diaminami alifatycznymi. Reakcja dwucentowego [Cd{SSi(OtBu)3}2]2 z poszczególnymi diaminami pozwala otrzymać pięć nowych obojętnych jednowymiarowych polimerów koordynacyjnych o różnej topologii łańcuchów [Cd{SSi(OtBu)3}2(μ-C4H12N2)(CH3OH)]n (1), [Cd{SSi(OtBu)3}2(μ-C5H14N2)(CH3OH)]n (2) [Cd{SSi(OtBu)3}2(μ-C6H16N2)(CH3OH)]n (3), [Cd{SSi(OtBu)3}2(μ-C7H18N2)]n...
-
Polyurethanes modified with natural polymers for medical application. Part II. Polyurethane/gelatin, polyurethane/starch, polyurethane/cellulose
PublicationThis paper is a literature overview of biomedical PUR modifications with natural polymers such as starch, cellulose and gelatin. Properties like biodegradability and biocompatibility of modified PUR cause that these materials may be used as wound dressings, tissue scaffolds, tissue implants and also vascular grafts.
-
Coffee silverskin as a potential bio-based antioxidant for polymer materials: Brief review
PublicationCoffee silverskin is one of the by-products generated by the coffee industry. Although it is not the most burdensome one, because it stands only for ~4.2 wt % of coffee, it seems like an auspicious raw material for industrial processes. Coffee silverskin is characterized by a relatively low moisture content of ~5–7%, so it often does not require quite energy-consuming drying processes. The chemical composition of coffee silverskin,...
-
Low-strain sensor based on the flexible boron-doped diamond-polymer structures
PublicationA free-standing high boron-doped diamond nanosheet (BDDNS) has been fabricated for the development of a flexible BDDNS strain senor. High boron-doped diamond was initially grown on a tantalum substrate in a microwave plasma-assisted chemical vapor deposition method, and was then transferred to a Kapton polymer substrate to fabricate the flexible BDDNS/Kapton device. Before performing the transfer process, the thin BDDNS’s morphology...
-
Environmentally friendly polymer-rubber composites obtained from waste tyres: A review
PublicationThe paper is transdisciplinary. The complex overview on changes in policy and approach to waste tyres that leads to both solving environmental problem of post consumer tyres and creating environmentally friendlier novel materials are presented. It is shown that in the world, the amount of polymer wastes increases every year. Most of them are in the form of post-consumer tyres. Recycling and recovery of such tyres is a serious environmental...
-
Chapter 12 ESR and ESR Imaging Methods for the Study of Oxidative Polymer Degradation
Publication -
Processing and thermal characterization of polymer derived SiCN(O) and SiOC reticulated foams
Publication -
Ru/Al2O3 on Polymer-Derived SiC Foams as Structured Catalysts for CO2 Methanation
Publication -
Polymer-derived Si3N4 nanofelts as a novel oil spills clean-up architecture
Publication -
Processing of polymer‐derived, aerogel‐filled, SiC foams for high‐temperature insulation
Publication -
Novel temperature operated electrooptical materials based on K2ZnCl4: PVA polymer nanocomposites
Publication -
Shaking table experimental study on the effectiveness of polymer bearings for seismic isolation of structures
PublicationSeismic isolation has been recognised to be a very effective way of protecting structures from damage during earthquakes. It allows us to extend the natural period of the structure and therefore avoid resonance with the ground motion. Moreover, by increasing damping in the isolation devices, more energy can be dissipated and thus the structural response can be further reduced. The aim of this paper is to show the results of the...
-
Hybrid electrodes composed of electroactive polymer and metal hexacyanoferrates in non-aqueous electrolytes
PublicationMateriały hybrydowe złożone z polimeru elektroaktywnego poli(3,4-etylenodioksytiofenu) (pEDOT) i heksacyjanożelazianów wybranych metali Mehcf (Me = Fe, Co, Ni) zostały poddane testom w elektrolitach niewodnych składających się z mieszaniny rozpuszczalników węglan etylenu (EC) : węglan propylenu (PC) w stosunku objętościowym 1:1 oraz wybranych soli: KPF6 i LiPF6. Właściwości elektrochemiczne materiałów badane były metodami woltamperometrii...
-
An Optical Low-Coherence System for 2-Dimensional Visualization of Thin Polymer Layers
PublicationW artykule omówiono zasadę działania i przedstawiono podstawowe właściwości systemu OCT (Optical Coherence Tomography). Na przykładzie folii polietylenowej przedyskutowano możliwości wykorzystania systemu do badanie wewnętrznej struktury warstwowej obiektów niebiologicznych. Przedstawiono i omówiono wyniki przeprowadzonych badań nad warstwowymi materiałami przeźroczystymi.
-
Magnetic Molecularly Imprinted Polymer Particles Synthesized by Suspension Polymerization in Silicone Oil
Publication -
In-Tube Molecularly Imprinted Polymer Solid-Phase Microextraction for the Selective Determination of Propranolol
Publication -
Growth of polymer brushes by “grafting from” via ATRP – Monte Carlo simulations
Publication -
Thermal stability and degradation of selected poly(alkyl methacrylates) used in the polymer industry
Publication -
Magnetic resonance imaging of radiation dose distributions using a polymer-gel dosimeter
Publication -
Fluorescence depolarization in the presence of excitation energy migration in partly ordered polymer films.
PublicationW pracy przedstawiono wyniki pomiarów i symulacji Monte Carlo zaników anizotropii emisji fluorescencji dla układu 3,3'-diethylthiacyanine iodine (barwnik) w osiowo rozciąganych foliach polimerowych.
-
Kinetics of photochromic reactions of substituted azobenzenes in solutions, and in liquid crystalline and polymer matrices
PublicationBadano kinetykę fotochromowych reakcji pochodnych azobenzenu: eterów koronowych z resztą benzenu i 4-metoksy-4´-halogenoazobenzenów zdolnych do tworzenia fazy ciekłokrystalicznej. Fotoaktywne związki rozpuszczano w alkanach, polimerach i w ciekłokrystalicznej matrycy. Izomeryzacja odpowiada kinetyce pierwszego rzędu w niektórych polimerach, jednakże stwierdzono zróżnicowanie stałych szybkości reakcji. Termiczna izomeryzacja cis-trans...
-
Potentiometric sensor with lipid-polymer membranes for quality assessment of French red wines
PublicationThe quality of wines resulting from vineyard management is important for consumers due to the taste and price of wines. In this work, the quality of red wines of three vintages has been investigated by potentiometric sensors with six all-solid-state electrodes. Two series of experiments were carried out. The first involved a qualitative analysis of wine of different vintages from freshly opened bottles. The second consisted of...
-
Wastes from Agricultural Silage Film Recycling Line as a Potential Polymer Materials
PublicationThe recycling of plastics is currently one of the most significant industrial challenges. Due to the enormous amounts of plastic wastes generated by various industry branches, it is essential to look for potential methods for their utilization. In the presented work, we investigated the recycling potential of wastes originated from the agricultural films recycling line. Their structure and properties were analyzed, and they were...
-
Rubber wastes recycling for developing advanced polymer composites: A warm handshake with sustainability
PublicationRecycling and management of rubber wastes experiences an early-stage maturity in the quest for sustainable and circular materials. Up to now, solutions proposed for sustainable development of rubber wastes are limited, so that properties and performance features of recycled products are inadequate for practical applications. Herein, an experimental protocol is introduced for manufacturing semi-sustainable polymer composites based...
-
Layer-by-layer polymer deposited fabrics with superior flame retardancy and electrical conductivity
PublicationSmart and multifunctional textiles and fabrics are progressively developing, such that multifunctional fabrics are becoming more widespread. We elaborated herein multi-layered flax fabrics with superior flame retardancy and conductivity, which revealed fireproof feature while keeping conductivity during burning. The flax fabric was reinforced by layer-by-layer (LbL) deposition of sodium polyacrylate (SPA), polyethylenimine (PEI),...
-
Properties of the Langmuir and Langmuir–Blodgett monolayers of cholesterol-cyclosporine A on water and polymer support
Publication -
The influence of temperature on properties of the polymer flexible joint used for strengthening historical masonries
PublicationA new method of repairing damaged structures by filling the cracks with a specially prepared elastomeric polymer mass has been recently proposed. This new and innovative technique, known as the Flexible Joint Method (FJM), is mainly dedicated to masonries and historical objects, where minimum intervention is permitted. The flexible joint bonds the disrupted elements and ensures further safe exploitation of a damaged structure....
-
Experimental study on the effectiveness of polymer damper in damage reduction of temporary steel grandstand
PublicationA large number of accidents, involving collapses of temporary grandstands during different types of events, were observed in the past. If the synchronized movement of people is tuned with the natural frequency of the affected part of the structure, resonance might occur. It may lead to severe damages of grandstands, their collapse or panic among the spectators. The aim of the paper is to assess, through preliminary experimental...
-
Novel cast polyetherurethanes based on dispersed polymeric polyols
PublicationOur study was focused on obtaining polyetherurethanes synthesized with using polymeric polyether based polyols differing in dispersed copolymer content (10, 20 and 40 wt%). The polyetherurethane materials were synthesized via two step method. The influence of different polymeric polyether based polyols on the chemical structure, morphology, mechanical and thermal properties of the obtained polyetherurethanes was investigated. The...
-
Identification of acrylate copolymers using pyrolysis and gas chromatography
Publication