Filtry
wszystkich: 1154
wybranych: 1073
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: METAL CATION COMPLEXATION
-
Assessment of fitness for service of Cr-Mo steel tubes in catalytic reforming charge heaters
PublikacjaIn this paper characteristic features of metal dusting corrosion in high temperature gas mixtures of high carbon activity in catalytic reforming units, including Continuous Catalyst Regeneration (CCR) platformer are presented. Examples of 2.25Cr-1Mo and 9Cr-1Mo steel tubes at advanced stages of metal dusting process after long-term service in charge heaters are used to prove that destructive examinations are necessary to provide...
-
The effect of pre-hydrogen charging on corrosion behaviour of superduplex stainless steel welded joints
PublikacjaThe paper presents results of research undertaken to determine the influence of hydrogen on passivity and corrosion resistance of 2507 super duplex stainless steel welded joints. Butt welded joints were made with low heat input using flux corded arc welding (FCAW) method. Coupons of 5.0 x 5.0 mm were cut from the welded joints containing weld metal (WM), heat affected zone (HAZ) and parent metal (PM). Hydrogen was introduced...
-
The use of Kamienna głowa cabbage species for phytoextraction of zinc and cadmium from the soil
PublikacjaAlthough traditional technologies for cleaning contaminated soils have proven to be efficient, they are usually expensive, labor intensive, and in the case of soil, they produce severe disturbance. Most recently, the use of plants in metal extraction (phytoremediation) has appeared as a promising alternative in the removal of heavy metal excess from soil. Phytoremediation uses of plant for pollutant stabilization, extraction, degradation,...
-
Diffusible Hydrogen Control in Flux Cored Arc Welding Process
PublikacjaOne of the types of hydrogen degradation of steel welded joints is cold cracking. The direct cause of the formation of cold cracks is simultaneous presence of hydrogen, residual stresses and brittle structure. The way of preventing the occurring of degradation is to eliminate at least one of these factors. Practice has shown that the best solution is to control the amount of hydrogen in deposited metal. In this paper an experimental...
-
The allergic and irritating reactions to metallic implants with trauma - orthopaedic patients
PublikacjaThe article presents the analysis of clinical operation complications after the treatment of long bones by mean of ostheosynthesis with the use of metal implants and endoprothesoplastic of hip joints.
-
Improvements to the two-phase sandwich method for calculating the melting points of pure metals
PublikacjaThe thermophysical properties of metal alloys are often investigated via molecular dynamics (MD) simulations.An exact and reliable estimation of the thermophysical parameters from the MD data requires a properly and carefullyelaborated methodology. In this paper, an improved two-phase sandwich method for the determination of the metal meltingtemperature is proposed, based on the solid-liquid equilibrium theory. The new method was...
-
Rozmieszczenie wybranych metali ciężkich w ekosystemie oczyszczalni hydrofitowej w Bielkowie.Distribution of heavy metals in ecosystem of free water surface system in Bielkowo.
PublikacjaIn the article the results of investigations of biomass crop and heavy metal contents in bottom sediments and in three species of plants (Glyceria maxima, Typha latifolia)inhabiting a wetland system in Bielkowo, Poland are presented. The measurements were carried out three times during the vegetation season (May, July and October). The contents of metals in different fragments of plants (leaves, stalks and roots) was analyzed....
-
Al-DIAMOND SCHOTTKY TUNNEL DIODES WITH BARRIER HEIGHT CONTROL
PublikacjaFew-nanometer-thick very highly boron-doped p-type layers were fabricated at metal-semiconductor interfaces of Schottky barrier diodes formed with aluminum on polycrystalline diamond. Preliminary results show that hermionically-assisted tunneling mechanism results in lower voltage drops at forward biasing of these diodes than expected for the Al-diamond metal-semiconductor potential barrier B. The effective barrier height Bpeff...
-
Investigation of vortex assisted magnetic deep eutectic solvent based dispersive liquid–liquid microextraction for separation and determination of vanadium from water and food matrices: Multivariate analysis
PublikacjaA new and simple vortex assisted magnetic deep eutectic solvent dispersive liquid–liquid microextraction procedure (VA-MDES-DLLME) was developed for the determination of vanadium (V) in food and water samples by flame atomic absorption spectrometry (FAAS). In the extraction medium, a bis(acetylpivalylmethane) ethylenediimine (H2APM2en) was used for the complexation of V(V) in sample solution at pH 6. The VA-MDES-DLLME was optimized...
-
Molecular dynamics simulations of the affinity of chitin and chitosan for collagen: the effect of pH and the presence of sodium and calcium cations
PublikacjaChitosan and chitin are promising biopolymers used in many areas including biomedical applications, such as tissue engineering and viscosupplementation. Chitosan shares similar properties with hyaluronan, a natural component of synovial fluid, making it a good candidate for joint disease treatment. The structural and energetic consequences of intermolecular interactions are crucial for understanding the biolubrication phenomenon...
-
Electron impact ionization and cationic fragmentation of the pyridazine molecules
PublikacjaElectron impact mass spectroscopy was used to investigate ionization and cationic fragmentation of the pyridazine (1,2 diazine), C4H4N2, molecules in the gas phase. The mass spectra were measured and the observed mass peaks assigned to the corresponding cations. The appearance energies of most of the cationic fragments were determined and the possible fragmentation processes are discussed. The total cross section for electron...
-
An Overview of the Development of a Real-Time System for Endoscopic Video Classification
PublikacjaThe article presents the results of improving endoscopic image classification algorithms in an effort towards applying them in a real-time diagnosis supporting system. Methods for the detection and removal of personal data are presented and discussed. The currently developed recognition algorithms have been improved in terms of accuracy and performance to make them suitable for a real-life implementation. Their test results are...
-
Bioaccumulation of Metals in Tissues of Marine Animals, Part I: the Role and Impact of Heavy Metals on Organisms
PublikacjaHeavy metals contribute to the anthropogenic contamination of marine ecosystems. Some of them are essential to the life processes of organisms; others are toxic, even at low concentrations. They penetrate organisms via food, respiratory pathways or the skin. The extent to which metals penetrate organisms is measured by the bioconcentration and bioaccumulation factors and also by their transport between organisms at different trophic...
-
In silico modelling for predicting the cationic hydrophobicity and cytotoxicity of ionic liquids towards the Leukemia rat cell line, Vibrio fischeri and Scenedesmus vacuolatus based on molecular interaction potentials of ions
PublikacjaIn this study we present prediction models for estimating in silico the cationic hydrophobicity and the cytotoxicity (log [1/EC50]) of ionic liquids (ILs) towards the Leukemia rat cell line (IPC-81), the marine bacterium Vibrio fischeri and the limnic green algae Scenedesmus vacuolatus using linear free energy relationship (LFER) descriptors computed by COSMO calculations. The LFER descriptors used for the prediction model (i.e....
-
Reaction of aniline with ammonium persulphate and concentrated hydrochloric acid: Experimental and DFT studies
PublikacjaIn this paper, the reaction of aniline with ammonium persulphate and concentrated HCl was studied. As a result of our experimental studies, 2,4,6-trichlorophenylamine was identified as the main product. This shows that a high concentration of HCl does not favour oxidative polymerisation of phenylamine, even though the ammonium persulphate/HCl system is widely used in polyaniline synthesis. On the basis of the experimental data...
-
Phosphinoborenium cations stabilized by N-heterocyclic carbenes: synthesis, structure, and reactivity
PublikacjaPhosphinoborenium cations stabilized by N-heterocyclic carbenes (NHCs) were synthesized via the reaction of bromo(phosphino)boranes with NHCs. Their structures were investigated by heteronuclear magnetic resonance spectroscopy, X-ray diffraction, and density functional theory calculations. They possess a planar trigonal boron center directly bonded with the pyramidal phosphanyl group (PR2) and can be treated as cationic phosphinoboranes....
-
Au-RE-TiO2 nanocomposites: Surface characteristics and photoactivity
PublikacjaThe photocatalysts based on TiO2 co-doped with rare earth metal (RE) and gold nanoparticles have been prepared using a sol-gel method and followed by gold reduction. Specific surface areas of the modified photocatalysts were calculated by the Brunauer-Emmett-Teller method (BET). Diffuse reflectance spectra of the obtained photocatalysts were recorded in a UV-Vis spectrophotometer (DRS UV-Vis). The influence of the type of rare...
-
Evaluation of organic coatings condition with AFM-based method
PublikacjaThe paper presents an atomic force microscopy (AFM)-based approach to evaluation of local protective properties of organic coatings. Apart from topography, it provides local ac and dc characteristics of examined coating. The method consists in application of ac voltage perturbation signal between conductive AFM tip and coated metal substrate. The resulting current is used to determine local impedance characteristics. Both impedance...
-
An experimental study of high-hydrogen welding processes
PublikacjaThis paper presents investigation results of determination of the diffusible hydrogen content in deposited metal obtained by means of two most often used methods-the glycerin method and the mercury method. Relation has been defined between results of those methods in the area characteristic of low-hydrogen as well as high-hydrogen welding processes. Relations available in the literature do not include the diffusible hydrogen content...
-
Hierarchical MnO2 nanoflowers blooming on 3D nickel foam: A novel micro-macro catalyst for peroxymonosulfate activation
PublikacjaIn this work, birnessite-type δ-MnO2 nanoflowers were uniformly deposited on 3D nickel foam (NF) by one-step hydrothermal route for high-efficient activation of peroxymonosulfate (PMS) towards degradation of acid orange 7 (AO7). High specific surface area, large pore volume and 3D hierarchical structure promotes the mass and electron transfer for great catalytic activity. Low reaction energy barrier (Ea=27.5 kJ/mol) and outstanding...
-
The properties of reduced Bi-Ge-O glasses for thermoelectric devices
PublikacjaThe bismuth-germanate glasses have been investigated to examine their applicability for thermoelectric devices. In order to increase their electrical conductivity, the 25Bi2O3–75GeO2 glass samples have been reduced at 340-380°C for 10 hours in hydrogen. It has been shown that such heat treatment in H2 leads to the reduction of metal ions Bi3+ and Ge4+ into neutral atoms and the formation of metal grains both in an amorphous glass...
-
Identyfikacja gatunku stali zastosowanej w obiektach budowlanych
PublikacjaEksploatacja istniejących metalowych konstrukcji budowlanych często związana jest z zagadnieniem koniecznej szczegółowej identyfikacji rodzaju materiału stalowego pod kątem je go cech wytrzymałościowych i składu chemicznego. Dostępne standardowe metody laboratoryjne zazwyczaj wymagają pobrania z konstrukcji próbek materiału do badań, co nie zawsze jest możliwe. W artykule zaprezentowano alternatywne metody oceny wymienionych cech...
-
Determination of Metals Content in Wine Samples by Inductively Coupled Plasma-Mass Spectrometry
PublikacjaKnowledge about the metal content of wine is very important, for many reasons. Depending on the element, its quantity varies in wine from ng/L to mg/L. Despite the fact that metals are not directly connected to the taste and aroma of the wine, their content should be determined and controlled, because excess is undesirable, and in some cases prohibited, due to potential toxicity. Several analytical procedures for metal determination...
-
Storage of High-Strength Steel Flux-Cored Welding Wires in Urbanized Areas
PublikacjaThe condition of the consumables is a key factor determining the waste reduction in the welding processes and the quality of the welded joint. The paper presents the results of tests of four types of fux-cored wires dedicated for welding high-strength steels, stored for 1 month and 6 months in Poland in two urbanized areas: in a large seaside city (Gdańsk) and in Warsaw, located in the center of the country. The wires were subjected...
-
Reactive imines: Addition of 2-aminopyrimidine to the imine bond and isolation of the aminal from the equilibrium mixture aminal/imine
PublikacjaThe reaction between o-vanillin and 2-aminopyrimidine leads to the formation of a single crystalline product: aminal, 1, which results from the reaction of the initially formed imine with 2-aminopyrimidine. The reaction was followed by the NMR spectroscopy. VT NMR studies prove that in solution two major species are observed: aminal and imine and their ratio depends on the time or/and temperature with the imine content increasing...
-
Impact of laser beam welding on mechanical behaviour of 2.25Cr–1Mo (P22) steel
PublikacjaThe use of welding processes in the manufacturing and repair of structures intended for the energy industry plays a key role in the guarantee of a continuous supply of fossil fuels, which is the basic condition for ensuring energy security. A square butt joint of 10 mm thick plate of 2.25Cr–1Mo (P22) steel was fabricated by autogenous laser beam welding process and then post-weld heat treatment (PWHT) for two sets of process parameters...
-
Hybrid Process Equipment: Improving the Efficiency of the Integrated Metalworking Machines Initial Designing
Publikacja -
Investigation of the Process of Automatic Control of Current Polarity Reversal in the Conditions of Hybrid Technology of Electrochemical Processing of Corrosion-Resistant Steels
Publikacja -
Technological features of forming the quality characteristics of the surface layer during diamond smoothing in the integrated processing
Publikacja -
Selection of form factors of machine carrying systems in reliance on the process duty
Publikacja -
The methods of technological machines’ rotors balance
Publikacja -
Cam mechanism designing with account of the technological load and energy costs
Publikacja -
Features of Machine Cyclogram Optimization with the Account of Interaction of Mechanism Links with Stops
Publikacja -
Determination of the rigidity and deformation energy of the technological machine load-carrying systems
Publikacja -
Structural Variety of Cobalt(II), Nickel(II), Zinc(II), and Cadmium(II) Complexes with 4,4′-Azopyridine: Synthesis, Structure and Luminescence Properties
PublikacjaSelf-assembled bi- and polymetallic complexes of CoII, NiII, ZnII, and CdII were obtained by the reaction of 4,4′-azopyridine (azpy) with metal tri-tert-butoxysilanethiolates (Co, 1; Cd, 2), acetylacetonates (Ni, 3; Zn, 4), and acetates (Cd, 5). All compounds were characterized by single-crystal X-ray structure analysis, elemental analysis, FTIR spectroscopy, and thermogravimetry. Complexes 1, 2 and 4, 5 exhibit diverse structural...
-
Preliminary studies of seamless flux cored wires stored in extreme conditions
PublikacjaIn the paper preliminary experimental studies of flux cored wires moisturized under controlled conditions are described. Three seamless wires of different grades have been placed in environmental chamber and moisturized in extremely adverse conditions (temperature T = 60° C, relative humidity H = 90%) for 240 hours. During this time measurements of weight gain and observations of surface of wires have been carried out. Also diffusible...
-
Mononuclear sodium(I) and copper(I) silanethiolates
PublikacjaStericallyencumberedligand(ArO) 3 SiS − , where Ar = 2,6-diisopropylphenyl, was employed for the synthesisof a dicoordinate copper(I) complex. The ligand creates a very hydrophobic environment around the metal center as indicated by the crystal structures and FT-IR spectroscopy.
-
Influence of PWHT Parameters on the Mechanical Properties and Microstructural Behavior of Multi-Pass GTAW Joints of P92 Steel
PublikacjaThe 9% Cr steels were developed for ultra-supercritical (USC) power plants to meet the requirements of high operating temperature and pressure. These steels are produced to operate at high temperatures where impact toughness is not a concern; however, it becomes important for the welded joints to have good impact toughness at room temperature for manufacturing. The present work investigates the effect of the post-weld heat treatment...
-
Morphology, Photocatalytic and Antimicrobial Properties of TiO2 Modified with Mono- and Bimetallic Copper, Platinum and Silver Nanoparticles
PublikacjaNoble metal nanoparticles (NMNPs) enhanced TiO2 response and extended its activity under visible light. Photocatalytic activity of TiO2 modified with noble metal nanoparticles strongly depends on the physicochemical properties of NMNPs. Among others, the differences in the size of NMNPs seems to be one of the most important factors. In this view, the effect of the metal’s nanoparticles size, type and amount on TiO2 photocatalytic...
-
Multifunctional catalyst-assisted sustainable reformation of lignocellulosic biomass into environmentally friendly biofuel and value-added chemicals
PublikacjaRapid urbanization is increasing the world's energy demand, making it necessary to develop alternative energy sources. These growing energy needs can be met by the efficient energy conversion of biomass, which can be done by various means. The use of effective catalysts to transform different types of biomasses will be a paradigm change on the road to the worldwide goal of economic sustainability and environmental protection. The...
-
The Idea of Using Adhesive Bonds in Shaping of Cold-formed Thin-walled Beam-columns
PublikacjaThe chapter concerns the idea of using adhesive bonds in the shaping of cold-formed thin-walled beam-columns. The idea of adhesive-bonded connections is not new but is unlikely to have been used in the design and shaping of thin-walled beam-columns in civil engineering up to date. Metal bar structures, including (due to economic reasons) thin-walled structures, are the most common and effective means to build engineering superstructures/loadbearing...
-
Interaction of Novel Ionic Liquids with Soils
PublikacjaWith the constant development of new ionic liquids, the understanding of the chemical fate of these compounds also needs to be updated. To this effect, in this contribution, the interaction of a number of novel ionic liquids with soils was determined. Therefore, three novel headgroups (ammonium, phosphonium or pyrrolidinium) with single or quaternary substitution were tested on a variety of soils with high to low organic matter...
-
Quality of bottled waters
PublikacjaBottled water is a product that is purchased by annually increasing numbers of people of all age groups. The quality control of mineral waters tends to concentrate on the determination of anion and cation levels, since it is these that govern the taste, smell and possible medicinal properties of the water. The constantly rising sales of mineral waters bring with them the ever increasing exploitation of their sources. The consequences...
-
Free volume in physical absorption of carbon dioxide in ionic liquids: Molecular dynamics supported modeling
PublikacjaUnderstanding the mechanisms underlying the carbon dioxide (CO2) absorption in ionic liquids (ILs) is the key to their efficient utilization in industrial flue gas treatment. One of the parameters considered substantially important in the process is the Free Volume. In this study, the Fractional Free Volume (FFV) of 73 ILs was calculated using Molecular Dynamics (MD). A quantitative Structure-Property Relationship (QSPR) study...
-
Ionic liquids in the microextraction techniques: the influence of ILs structure and properties
PublikacjaIonic liquids (ILs) are composed entirely of ions thus they possess unique properties, including negligible volatility, a liquid state in a broad range of temperatures and ability to change them depending on the chosen type of anion and cation, which make ILs unique and useful for many applications in sample preparation techniques. A deeper understanding of the nature of ILs and the impact of their structure on their parameters...
-
A general approach to study molecular fragmentation and energy redistribution after an ionizing event
PublikacjaWe propose to combine quantum chemical calculations, statistical mechanical methods, and photoionization and particle collision experiments to unravel the redistribution of internal energy of the furan cation and its dissociation pathways. This approach successfully reproduces the relative intensity of the different fragments as a function of the internal energy of the system in photoelectron–photoion coincidence experiments and...
-
Photophysics of Untethered ZnTPP-Fullerene Complexes in Solution
PublikacjaThe spectroscopy and dynamic behavior of the self-assembled, Soret-excited zinc tetraphenylporphyrin (ZnTPP) plus fullerene (C60) model system in solution has been examined using steady state fluorescence quenching, nanosecond time-correlated single photon counting, picosecond fluorescence upconversion, and picosecond transient absorption methods. Evidence of ground state complexation is presented. Steady-state quenching of the...
-
Hydrogen effects in duplex stainless steel welded joints - electrochemical studies
PublikacjaIn this work results on the influence of hydrogen on passivity and corrosion resistance of 2205 duplex stainless steel (DSS) welded joints are described. The results were discussed by taking into account three different areas on the welded joint: weld metal (WM), heat-affected zone (HAZ) and parent metal. The corrosion resistance was qualified with the polarization curves registered in a synthetic sea water. The conclusion is that,...
-
Binuclear Co(II), Zn(II) and Cd(II) tri-tert-butoxysilanethiolates. Synthesis, crystal structure and spectroscopic studies.
PublikacjaA series of Co(II), Zn(II) and Cd(II) complexes have been synthesized in reaction of respective metal tri-tert-butoxysilanethiolates with pyrazine 1 and 2 and 1,2-bis(2-pyridyl)ethylene 3–5. All compounds have been characterized by single-crystal X-ray structure determination, elemental analysis, FT-IR and thermogravimetry. Obtained complexes are bimetallic with the formula of [M{SSi(OtBu)3}2(μ-L)]2 and metal ions bridged by N,N′-spacer....
-
Effect of electrode waterproof coating on quality of underwater wet welded joints
PublikacjaIn this paper, the effects of different hydrophobic coatings on the surface of covered electrodes on the quality of wet welded carbon steel joints were discussed. Commonly available hydrophobic substances used in industrial applications were selected for the research. The aim of using waterproof coatings was to check the possibility to decreasing the susceptibility of highstrength low-alloy S460N steel to cold cracking. During...