Filtry
wszystkich: 782
wybranych: 686
-
Katalog
Filtry wybranego katalogu
Wyniki wyszukiwania dla: Machine Learning
-
Failure analysis of a high-speed induction machine driven by a SiC-inverter and operating on a common shaft with a high-speed generator
PublikacjaDue to ongoing research work, a prototype test rig for testing high-speed motors/generators has been developed. Its design is quite unique as the two high- speed machines share a single shaft with no support bearings between them. A very high maximum operating speed, up to 80,000 rpm, was required. Because of the need to minimise vibration during operation at very high rotational speeds, rolling bearings were used. To eliminate...
-
EXPERIMENTAL AND NUMERICAL INVESTIGATION ON SPECIMEN GEOMETRY EFFECT ON THE CTOD VALUE FOR VL-E36 SHIPBUILDING STEEL
PublikacjaThere are special cases in the marine industry, where additional material tests, such as the fracture toughness test, must be performed. Additional fracture toughness tests, such as CTOD (Crack Tip Opening Displacement), are typically performed on three-point bend specimens. The dimension that defines all the specimen dimensions is the thickness of the material to be tested. It is recommended by classification societies (e.g. DNVGL)...
-
Planning optimised multi-tasking operations under the capability for parallel machining
PublikacjaThe advent of advanced multi-tasking machines (MTMs) in the metalworking industry has provided the opportunity for more efficient parallel machining as compared to traditional sequential processing. It entailed the need for developing appropriate reasoning schemes for efficient process planning to take advantage of machining capabilities inherent in these machines. This paper addresses an adequate methodical approach for a non-linear...
-
Noise sources in Raman spectroscopy of biological objects
PublikacjaWe present an overview of noise sources deteriorating the quality of the recorded biological Raman spectra and the ability to determine the specimen composition. The acquired Raman spectra exhibit intense additive noise components or drifts because of low intensity of the scattered light. Therefore we have to apply expensive or bulky measurement setups to limit their inherent noise or to apply additional signal processing to reduce...
-
The Method of Selecting the Interval of Functional Tests Taking into Account Economic Aspects and Legal Requirements
PublikacjaThe article discusses the problem of choosing the optimal frequency of functional tests, taking into account the reliability and law requirements, but also the impact of business aspects in the company. The subject of functional test interval is well described for purposes of the process industry. Unfortunately, this is not the case for the machinery safety functions with low demand mode. This is followed by a presentation of the...
-
NUMERICAL SIMULATIONS OF HONING PROCESS OF THIN WALL CYLINDER LINERS, WITH CONSTANT AND WITH VARIABLE THICKNESS OF WALL OF HONED PARTS
PublikacjaNumerical simulations of honing process of thin-wall cylinder liners, with constant and with variable thickness of the wall of honed workpieces can improve and can help to conduct the experimental research of honing process and can improve the honing process. A very valuable research assumption, before performing the numerical analysis of computer simulation of honing process, is the measurement of the real geometry of the honing...
-
Multi-criteria Robot Selection Problem for an Automated Single-Sided Lapping System
PublikacjaFlat lapping is a crucial process in a number of precision manufacturing technologies. Its aim is to achieve extremely high flatness of the workpiece. Single-sided lapping machines have usually standard kinematic systems and are used in conjunction with conditioning rings, which are set properly be-tween the center and the periphery of the lapping plate. In this paper, instead of conventional single-side lapping machine, an automated...
-
Future Skills and Education in a Computerized World
PublikacjaAs computerization of Western economies has advanced, the supply of the demand for routine cognitive tasks and routine manual tasks has fallen. Computerization has increased labour input of nonroutine cognitive tasks which has favourized high educated workers. Similarly, there is clear evidence of an increase in demand for high skilled workforce which originates from poor machine performance of nonroutine...
-
Technical Engine for Democratization of Modeling, Simulations, and Predictions
PublikacjaComputational science and engineering play a critical role in advancing both research and daily-life challenges across almost every discipline. As a society, we apply search engines, social media, and se- lected aspects of engineering to improve personal and professional growth. Recently, leveraging such aspects as behavioral model analysis, simulation, big data extraction, and human computation is gain- ing momentum. The nexus...
-
Effect of selective laser treatment on initiation of fatigue crack in the main part of an undercarriage drag strut
PublikacjaThis paper presents the results of material characterization and a fatigue test conducted for a laser-re-melted drag strut used in an aircraft landing gear. The drag strut was re-melted with a CO2 laser beam. Eight re-melted paths were made in the form of spiral lines along the axis of the drag strut. Next, the drag strut was subjected to variable loads on a testing machine simulating loads occurring when an aircraft lands. The...
-
Properties of Old Concrete Built in the Former Leipziger Palace
PublikacjaThis research aims to determine the mechanical, chemical, and physical properties of old concrete used in the former Leipziger Palace in Wrocław, Poland. The cylindrical specimens were taken from the basement concrete walls using a concrete core borehole diamond drill machine. The determination of the durability and strength of old concrete was based on specified chosen properties of the old concrete obtained through the following...
-
Emission of 1.3–10 nm airborne particles from brake materials
PublikacjaOperation of transport vehicle brakes makes a significant contribution to airborne particulate matter in urban areas, which is subject of numerous studies due to the environmental concerns. We investigated the presence and number fractions of 1.3–10 nm airborne particles emitted from a low-metallic car brake material (LM), a non-asbestos organic car brake material (NAO) and a train brake cast iron against a cast iron. Particles...
-
Comparison of Surface Quality and Tool-Life of Glulam Window Elements after Planing
PublikacjaThe quality of the surface of wooden elements, that have been planed, has a crucial importance in the whole production process, since the obtained effects affect the quality of wooden surface after fi nishing (painting). The occurrence of defects is usually the reason for qualifying a workpiece as scrap or for requiring additional work. This paper presents the selected results of research of the effect of the cutting tool wear...
-
The Proposition of an Automated Honing Cell with Advanced Monitoring
PublikacjaHoning of holes allows for small shape deviation and a low value of a roughness profile parameter, e.g., Ra parameter. The honing process heats the workpiece and raises its temperature. The increase in temperature causes thermal deformations of the honed holes. The article proposes the construction of a honing cell, containing in addition to CNC honing machine: thermographic camera, sound intensity meter, and software for collecting...
-
The influence oil additives on spread cracks in silicon nitride
PublikacjaThe paper presents an experimental study of the influence of oil additives (Cl, S, P, cerium dioxide (CeO2)) on spread cracks in silicon nitride. The additives Cl, S, P are bound in molecules in liquid form soluble in the base oil. The CeO2 is purely in powder form in suspension. The use of CeO2 powder was made based on the good results of polishing of silicon nitride. A ceramic angular contact ball bearing was modelled using a...
-
A Simplified SVPWM Technique for Five-leg Inverter with Dual Three-phase Output
PublikacjaThis article proposes a simplified space vector pulse-width modulation (SVPWM) technique five-leg inverter with dual three-phase output. An idea to fed the dual tree-phase machine by the multiphase voltage source inverters (VSIs) is not new. Dual- and multi-motor drive systems are widely used in the industry applications. The most popular fields are: electric vehicles (EVs) and traction systems. Moreover, the specific characteristic...
-
Adaptive system for recognition of sounds indicating threats to security of people and property employing parallel processing of audio data streams
PublikacjaA system for recognition of threatening acoustic events employing parallel processing on a supercomputing cluster is featured. The methods for detection, parameterization and classication of acoustic events are introduced. The recognition engine is based onthreshold-based detection with adaptive threshold and Support Vector Machine classifcation. Spectral, temporal and mel-frequency descriptors are used as signal features. The...
-
Improving performance of large thrust bearings through modeling and experimentation
PublikacjaLarge thrust bearings are highly loaded machine elements and their failures cause serious losses. Start ups and stoppages of the bearing under load are specially critical regimes of operation. Load carrying capacity depends on the profile of the oil gap. In transient states this profile is also changing. In the design of large thrust bearings minimizing thermo-elastic deformations is an important goal, which can be accomplished...
-
Moisture content during and after high- and normal-temperature drying processes of wood
PublikacjaThe aim of the article is to present the results of moisture content of wood during and after the high-temperature steam and air–steam mixture drying processes and after an open air-drying process. The knowledge of moisture content changes of wood in the process of its drying is one of the important parameters to economy drying process and to keep the quality of dried wood. Wood samples, namely, spruce (Picea abies K.) and beech...
-
Objectivization of phonological evaluation of speech elements by means of audio parametrization
PublikacjaThis study addresses two issues related to both machine- and subjective-based speech evaluation by investigating five phonological phenomena related to allophone production. Its aim is to use objective parametrization and phonological classification of the recorded allophones. These allophones were selected as specifically difficult for Polish speakers of English: aspiration, final obstruent devoicing, dark lateral /l/, velar nasal...
-
Privacy-Preserving, Scalable Blockchain-Based Solution for Monitoring Industrial Infrastructure in the Near Real-Time
PublikacjaThis paper proposes an improved monitoring and measuring system dedicated to industrial infrastructure. Our model achieves security of data by incorporating cryptographical methods and near real-time access by the use of virtual tree structure over records. The currently available blockchain networks are not very well adapted to tasks related to the continuous monitoring of the parameters of industrial installations. In the database...
-
Effective density of airborne wear particles from car brake materials
PublikacjaPeople living in urban environments are subject to high health risks due to various anthropogenic sources of airborne particulate matter, including wear of transport vehicle brakes. Studies of airborne particles often require an estimate of the effective particle density, a property that allows correct matching of mass and size characteristics measured by different aerosol instruments. In this study we investigated the effective...
-
Porosity and shape of airborne wear microparticles generated by sliding contact between a low-metallic friction material and a cast iron
PublikacjaThe wear of brakes in transport vehicles is one of the main anthropogenic sources of airborne particulate matter in urban environments. The present study deals with the characterisation of airborne wear microparticles from a low-metallic friction material / cast iron pair used in car brakes. Particles were generated by a pin-on-disc machine in a sealed chamber at sliding velocity of 1.3 m/s and contact pressure of 1.5 MPa. They...
-
Revisiting the estimation of cutting power with different energetic methods while sawing soft and hard woods on the circular sawing machine: a Central European case
PublikacjaIn the classical approaches, used in Central Europe in practice, cutting forces and cutting power in sawing processes of timber are commonly computed by means of the specific cutting resistance kc. It needs to be highlighted that accessible sources in handbooks and the scientific literature do not provide any data about wood provenance, nor about cutting conditions, in which cutting resistance has been empirically determined. In...
-
A Critical Reanalysis of Uncontrollable Washboarding Phenomenon in Metal Band Sawing
PublikacjaThe article analyzes the cutting process of hard bars. Investigations conducted in industrial conditions demonstrated the presence of surface errors in the machined workpieces in the form of washboard patterns. The purpose of this study was to analyze the results of cutting on band sawing machines with different band saw blades. The cutting processes were conducted on three different horizontal band sawing machine types. Analyzed...
-
Chemical, Physical, and Mechanical Properties of 95-Year-Old Concrete Built-In Arch Bridge
PublikacjaThis research aimed to determine the durability and strength of an old concrete built-in arch bridge based on selected mechanical, physical, and chemical properties of the concrete. The bridge was erected in 1925 and is located in Jagodnik (northern Poland). Cylindrical specimens were taken from the side ribs connected to the top plate using a concrete core borehole diamond drill machine. The properties of the old concrete were...
-
Programowo-sprzętowa platforma symulacyjna - Hardware In the Loop - zaawansowanego układu sterowania poziomem wody w pionowej wytwornicy pary elektrowni jądrowej
PublikacjaW artykule przedstawiono koncepcję programowo-sprzętowej platformy symulacyjnej wykorzystującej technikę symulacji w pętli sprzętowej HIL (ang. Hardware In The Loop simulation), wykorzystanej dla potrzeb projektowania i weryfikacji w czasie rzeczywistym (ang. Real Time) zaawansowanych algorytmów sterowania poziomem wody w pionowej wytwornicy pary elektrowni jądrowej. Jej głównymi elementami są: środowisko czasu rzeczywistego Matlab/Simulink...
-
A System for Heart Sounds Classification
PublikacjaThe future of quick and efficient disease diagnosis lays in the development of reliable non-invasive methods. As for the cardiac diseases – one of the major causes of death around the globe – a concept of an electronic stethoscope equipped with an automatic heart tone identification system appears to be the best solution. Thanks to the advancement in technology, the quality of phonocardiography signals is no longer an issue. However,...
-
Multicomponent ionic liquid CMC prediction
PublikacjaWe created a model to predict CMC of ILs based on 704 experimental values published in 43 publications since 2000. Our model was able to predict CMC of variety of ILs in binary or ternary system in a presence of salt or alcohol. The molecular volume of IL (Vm), solvent-accessible surface (Sˆ), solvation enthalpy (DsolvGN), concentration of salt (Cs) or alcohol (Ca) and their molecular volumes (Vms and Vma, respectively) were chosen...
-
The experimental identification of the dynamic coefficients of two hydrodynamic journal bearings operating at constant rotational speed and under nonlinear conditions.
PublikacjaHydrodynamic bearings are commonly used in ship propulsion systems. Typically, they are calculated using numerical or experimental methods. This paper presents an experimental study through which it has been possible to estimate 24 dynamic coefficients of two hydrodynamic slide bearings operating under nonlinear conditions. During the investigation, bearing mass coefficients are identified by means of a newly developed algorithm....
-
HIERARCHICAL CYCLES IN MODERN POWER SYSTEMS – EXERGY ANALYSIS UNDER PART LOADS
PublikacjaThe aim of the paper is to investigate thermodynamic efficiency of advanced hierarchic power cyclesunder partial loads by using of exergy analyze. Advanced hierarchical power systems arecomposed of few energy conversion cycles, most common are steam and gas cycles in various configurations, but they may contain fuel cells, ORC, lithium bromide absorption chillers and others. Moreover hierarchical cycles can be powered by several...
-
Laxer Clinical Criteria for Gaming Disorder May Hinder Future Efforts to Devise an Efficient Diagnostic Approach: A Tree-Based Model Study
PublikacjaInternet Gaming Disorder (IGD) has been recognized in May 2013 and can be evaluated using the criteria developed by American Psychiatric Association (APA). The present study investigated the role each IGD criteria plays in diagnosing disordered gaming. A total of 3,377 participants (mean age 20 years, SD = 4.3 years) participated in the study. The data collected was scrutinized to detect patterns...
-
Real-time hybrid model of a wind turbine with doubly fed induction generator
PublikacjaIn recent years renewable sources have been dominating power system. The share of wind power in energy production increases year by year, which meets the need to protect the environment. Possibility of conducting, not only computer simulation, but also laboratory studies of wind turbine operation and impact on the power system and other power devices in laboratory conditions would be very useful. This article presents a method...
-
The Influence of Workpiece Hardness on Plate Temperature during One Side Lapping
PublikacjaLapping leads to a surface with low roughness and high precision. Because of required parts accuracy tool flatness is the key to the successful machining. To avoid its excessive thermal expansion, plate temperature research was taken. The goal was to determine the correlation between the basic lapping conditions and wheel temperature. In work Bulsara et al. authors developed model to estimate the maximum and average temperature...
-
The adaptive backstepping control of PMSM supplied by current source inverter for the field weakening region
PublikacjaThe sensorless control system of permanent magnet synchronous motor PMSM supplied by current source inverter for field weakening operation is presented in this paper. The adaptive backstepping control system and the backstepping speed observer are presented. The control system is based on multi-scalar variables. The control variables are: dc-link voltage and the output current vector pulsation. The control system was named voltage...
-
Applications of Additively Manufactured Tools in Abrasive Machining—A Literature Review
PublikacjaHigh requirements imposed by the competitive industrial environment determine the development directions of applied manufacturing methods. 3D printing technology, also known as additive manufacturing (AM), currently being one of the most dynamically developing production methods, is increasingly used in many different areas of industry. Nowadays, apart from the possibility of making prototypes of future products, AM is also used...
-
Systematic Literature Review for Emotion Recognition from EEG Signals
PublikacjaResearchers have recently become increasingly interested in recognizing emotions from electroencephalogram (EEG) signals and many studies utilizing different approaches have been conducted in this field. For the purposes of this work, we performed a systematic literature review including over 40 articles in order to identify the best set of methods for the emotion recognition problem. Our work collects information about the most...
-
Core loss resistance impact on sensorless speed control of an induction motor using hybrid adaptive sliding mode observer
PublikacjaInduction motors (IMs) experience power losses when a portion of the input power is converted to heat instead of driving the load. The combined effect of copper losses, core losses, and mechanical losses results in IM power losses. Unfortunately, the core losses in the motor, which have a considerable impact on its energy efficiency, are not taken into account by the generally employed dynamic model in the majority of the studies. Due...
-
Axial-Flux Permanent-Magnet Dual-Rotor Generator for a Counter-Rotating Wind Turbine
PublikacjaCoaxial counter-rotating propellers have been widely applied in ships and helicopters for improving the propulsion efficiency and offsetting system reactive torques. Lately, the counter-rotating concept has been introduced into the wind turbine design. Distributed wind power generation systems often require a novel approach in generator design. In this paper, prototype development of axial-flux generator with a counter-rotating...
-
Diagnostic system of wheeled tractors detecting four defect's categories
PublikacjaIn a classical approach to damage diagnosis, the technical condition of an analyzed machine is identified based on the measured symptoms, such as performance, thermal state or vibration parameters. In wheeled tractor the fundamental importance has monitoring and diagnostics during exploitation concerning technical inspection and fault element localizations. The main functions of a diagnostic system are: monitoring tractor components...
-
Programowo-sprzętowa platforma symulacyjna - Hardware In the Loop - zaawansowanego układu sterowania poziomem wody w pionowej wytwornicy pary elektrowni jądrowej
PublikacjaW artykule przedstawiono koncepcję programowo-sprzętowej platformy symulacyjnej wykorzystującej technikę symulacji w pętli sprzętowej HIL (ang. Hardware In The Loop simulation), wykorzystanej dla potrzeb projektowania i weryfikacji w czasie rzeczywistym (ang. Real Time) zaawansowanych algorytmów sterowania poziomem wody w pionowej wytwornicy pary elektrowni jądrowej. Jej głównymi elementami sa: środowisko czasu rzeczywistego Matlab/Simulink...
-
Circular saw vibrations or dynamics of the spindle
PublikacjaSawing of wood with circular saws is a typical example of cutting with multi-blade tools. In that kind of cutting, theposition accuracy of following tool blades is a crucial factor which affects the cutting process and machining final effects.Position tooth errors may cause deterioration in cutting conditions, changes in loads of individual teeth and the tool as a whole,and also a decrease in accuracy and surface quality after...
-
A Concept for Safe and Less Expensive Acceleration of a Marine Steam Turbine Start-up
PublikacjaThis paper analyses the issue of accelerated start-up of a marine steam turbine, which is an important problem because the start-up of a steam machine involves the combustion of fuel that is not transformed into useful energy. To find novel technologies that offer improvements in this aspect is essential due to restrictions on reducing ship emissions. Thus, the shorter the start-up time, the better for the environment and economy....
-
Theoretical analysis and experimental tests of tilting pad journal bearings with shoes made of polymer material and low-boiling liquid lubrication
PublikacjaSelecting the appropriate bearing system for the rotor requires a good knowledge of the available solutions and the operating conditions of the machine. For newly designed machinery operating in adverse conditions, selecting bearings that ensure correct and long-lasting operation can be extremely challenging. Difficulties in- crease when the machine’s operating parameters are beyond the technical capabilities of available technical solutions....
-
Effect of presence of lifting pocket on the THD performance of a large tilting-pad thrust bearing
PublikacjaHydrostatic assistance is a commonly used method to improve limited load carrying ability of tiltingpad thrust bearings during transient states of operation of vertical shaft hydro-generators. Despite of special hydraulic equipment (as pumps, valves, etc.), it also requires manufacturing of special recesses/pockets at pad sliding surfaces, into which oil is injected under high pressure. It allows to lift the rotor before start-up...
-
Chemical Theory of Machines, basic principles of strength with examples of calculations
PublikacjaThis book encompasses the essential range of information on technical aspects of mechanical design. It was written primarily for the students and staff of chemistry faculties of technical universities, yet it may also be utilized by everyone, who ether would like to try or already enjoys designing, but cannot take advantage of typical stress & machine construction handbooks. These handbooks often require familiarity with the concepts...
-
Influence and development of new kinematic systems in flat surface lapping
PublikacjaThe face grinding and lapping technology is widely used in the field of the precise and ultraprecise manufacturing. It has become an indispensable technology in the manufacture of many parts. An absence of material restrictions allows machining both metal and non-metallic materials, including technical ceramics [1]. Nowadays there are mainly two kinematic systems in lapping machines [2]. The machining plane-parallel surfaces is...
-
Image Representation for Cognitive Systems Using SOEKS and DDNA: A Case Study for PPE Compliance
PublikacjaCognitive Vision Systems have gained significant interest from academia and industry during the past few decade, and one of the main reasons behind this is the potential of such technologies to revolutionize human life as they intend to work under complex visual scenes, adapting to a comprehensive range of unforeseen changes, and exhibiting prospective behavior. The combination of these properties aims to mimic the human capabilities...
-
Modélisation des machines synchrones par des systèmes d’ordre un demi. Procédure d’identification des paramètres du schéma équivalent, analyse de sensibilité des paramètres.
PublikacjaCe livre présente de nouveaux modèles de machines synchrones (alternateurs à pôles saillants et alternateur à aimants permanents). Les schémas équivalents de ces modèles sont établis en utilisant la modélisation fractionnaire. Ceci permet de construire des modèles les plus compacts possibles, c’est-à-dire d’ordre réduit. Les branches (R-L) dans le schéma équivalent classique, décrivant les différentes parties de la machine où les...
-
“Shadow” vs. “Phase 3D” method within endoscopic examinations of marine engines
PublikacjaA visual investigation of surfaces creating internal, working spaces of marine combustion engines by means of specialized view-finders so called endoscopes is at present almost a basic method of technical diag-nostics. The surface structure of constructional material is visible during investigations like through the magnifying glass (usually with a precisely determined magnification), which makes possible a detection, recognition...