Filtry
wszystkich: 420
wybranych: 329
Wyniki wyszukiwania dla: WATER LUBRICATION, FRICTION, WEAR, SOLID PARTICLES
-
Solid phase microextraction–comprehensive twodimensional gas chromatography–time-of-flight mass spectrometry: a new tool for determining PAHs in airport runoff water samples
Publikacjafundamental aspect of airport operations is the pollution caused by airport runoff waters. Polycyclic aromatic hydrocarbons (PAHs) are one of the most important groups of xenobiotics which are commonly found in runoff water originating from airports. Only very limited data on the analysis of airport runoff water have been published until now. Therefore, a reliable and accurate analytical method based on headspace solid-phase microextraction...
-
Solid-Contact pH Sensor without CO2Interference with a Superhydrophobic PEDOT-C14as Solid Contact: The Ultimate “Water Layer” Test
Publikacja -
WEAR TESTING OF DLC COATINGS WITH FRICTION COUPLE „BALL-ON-DISK” = Badania zużycia powłok DLC w skojarzeniu kula-tarcza obrotowa ''ball-on-disk''
PublikacjaW Katedrze Konstrukcji i Eksploatacji Maszyn PG opracowano metodę badania powłok DLC oraz innych (ceramicznych) w układzie kula - płaska powierzchnia obrotowej tarczy ("ball-on-disk"). Układ badawczy składa się z kuli osadzonej w popychaczu łożyskowanym tocznie, poprzez który wywierana jest siła docisku próbek. Kula dociskana jest od góry do płaskiej powierzchni obrotowej tarczy - próbki dolnej (o pionowej osi obrotu). Próbka dolna...
-
Effects of Heat and Momentum Gain Differentiation during Gas Detonation Spraying of FeAl Powder Particles into the Water
Publikacja -
Core-shell cobalt particles Co@CoO loaded on nitrogen-doped graphene for photocatalytic water-splitting
Publikacja -
Ocena odporności powłok na bazie DLC na doraźne uszkodzenie w warunkach tarcia ślizgowego ze smarowaniem wodą i solą fizjologiczną = Evaluation of DLC based coatings resistance to instanteneous damage under sliding friction conditions with distilated water or saline lubrication
PublikacjaWykonano serię testów w celu wyznaczenia granicznych warunków wymuszenia, zdefiniowaego jako średnie naciski powierzchniowe oraz prędkość ślizgania, po przekroczeniu których następuje gwałtowne zniszczenie powłoki. Na podstawie wyników pomiarów opracowano aproksymowane charakterystyki granicznych wymuszeń w układzie p - v oraz pokrewnych dla badanych materiałów, smarów i zakresu parametrów wymuszenia.
-
Experimental research on water lubricated three layer sliding bearing with lubrication grooves in the upper part of the bush and its comparison with a rubber bearing
Publikacjacomposite. Eachofitslayershasanimportantfunction.Speciallypreparedslidingsurfaceensures minimum resistance.Followingrunning-initssmoothnessbecomesveryhighandthebearingmay continue workingunder fluid lubricationregime.NBRlayerensuresbearingelasticity,goodvibration damping propertiesandinsusceptibilitytoshaftaxismisalignment.Theexternalbrasslayermakes fitting thebearingeasier. Experiment resultsoftheconductedresearchwerecomparedwiththoseforarubberbearingof similar...
-
Dispersive Micro‐Solid Phase Extraction of Selected Metals in Water and Food Samples Followed by ICP‐OES Analysis: Method Development, Analysis of Real Samples and Greenness Evaluation
PublikacjaMultiwalled carbon nanotubes (MWCNTs) are well-known adsorbents because of their high surface area, layered and hollow architecture, hydrophobicity, and multiple and easily accessible adsorption sites. In this study, MWCNTs were used for dispersive micro-solid-phase extraction of various metal chelates in environmental and food samples. Different parameters such as concentration of the chelating reagent, the sorbent dosage, the...
-
Evaluation, Pitfalls and Recommendations for the “Water Layer Test” for Solid Contact Ion‐selective Electrodes
Publikacja -
Determination of pesticides in water using new solid phase extraction technique - speedisk and speedisk column.
PublikacjaW publikacji opisano zastosowanie nowych narzędzi do ekstrakcji do fazy stałej: szybkie dyski i szybkie kolumienki (speedisk i speedisk column). Zaprezentowano ich zastosowanie do ekstrakcji pestycydów z próbek wody, przy zastosowaniu różnych rozpuszczalników.
-
Powłoki fluoropolimerowe oraz przeciwzatarciowe w łożyskach foliowych smarowanych wodą = Fluoropolymer and anti-friction coatings for water-lubricated foil bearings
PublikacjaW artykule przedstawiono krótką charakterystykę oraz wyniki badań tribologicznych wybranych powłok fluoropolimerowych oraz przeciwzatarciowych. Badania zużycia powłok przeprowadzono pod kątem zastosowania w oryginalnym łożysku foliowym smarowanym wodą. Na podstawie analizy wyników wyłoniono trzy powłoki do potencjalnego zastosowania w łożyskach foliowych smarowanych wodą.
-
The quantification of bisphenols and their analogues in wastewaters and surface water by an improved solid-phase extraction gas chromatography/mass spectrometry method
Publikacja -
New approach based on solid-phase extraction for the assessment of organic compound pollutions in so-called pharmaceutically pure water
PublikacjaOpisano mozliwość zastosowania nowej procedury analitycznej opartej na wykorzystaniu techniki ekstrakcji do fazy stałej (na etapie izolacji i wzbogacania analitów) do oznaczania śladowych ilości zanieczyszczeń organicznych w wodzie specjalnej czystości używanej do celów farmaceutycznych.Próbka badanej wody jest przepuszczana przez złoże sorbenta, które jest osuszane za pomocą strumienia oczyszczonego powietrza, przed etapem termicznej...
-
Estimation of platinum in environmental water samples with solid phase extraction technique using inductively coupled plasma mass spectrometry
PublikacjaZoptymalizowano metodykę oznaczania śladowych poziomów stężeń platyny (IV) w oparciu o technikę ekstrakcji do fazy stałej w połączeniu ze spektrometrią mas z plazmą wzbudzoną indukcyjnie. Na etapie wzbogacania platyny wykorzystano żel krzemionkowy modyfikowany grupami aminopropylowymi. Ilościowy odzysk platyny uzyskano poprzez wykorzystanie 1.0 mol L-1 roztworu tiomocznika jako eluenta. Odchylenie standardowe wyników (RSD) było...
-
Ionogel sorbent coatings for determining organophosphorus and pyrethroid insecticides in water and fresh juice samples by headspace-solid phase microextraction
PublikacjaThe sol–gel method yielded three different ionogel sorbent coatings that were obtained based on a silica material containing ionic liquids (ILs) immobilized in its pores. Two ILs, triethylsulfonium bis(trifluoromethylsulfonyl) imide [Set3][TFSI] and 1-butyl-1-methylpiperidinium bis(trifluoromethylsulfonyl)imide [C4C1Pip][TFSI], as well as their equimolar mixture [Set3/C4C1Pip], were used to obtain ionogel fibers. The developed...
-
Determination of volatile organic compounds in water samples using membrane-solid phase microextraction (M-SPME) (headspace version)
PublikacjaThe results of a study on the use of membrane-solid phase microextraction (M-SPME) for sampling volatile organic compounds (VOCs) from the headspace above the liquid medium are presented. The sampled VOCs were subsequently quantified by gas chromatography (GC). Two systems were compared in this study, i.e. a novel two-phase sorption system (M-SPME), and a commercial fibre. Headspace sampling using SPME was optimized with respect...
-
Chemical pollution and toxicity of water samples from stream receiving leachate from controlled municipal solid waste (MSW) landfill
PublikacjaThe present study was aimed to determine the impact of municipal waste landfill on the pollution level of surface waters, and to investigate whether the choice and number of physical and chemical parameters monitored are sufficient for determining the actual risk related to bioavailability and mobility of contaminants. In 2007–2012, water samples were collected from the stream flowing through the site at two sampling locations,...
-
RESEARCH ON HYDRODYNAMIC PEEK JOURNAL BEARINGS LUBRICATED WITH WATER AND OIL
PublikacjaThe main purpose of the research was to determine the possibilities and experimentally test the benefits of replacing conventional oil lubrication with ecological water lubrication. Tests were carried out on a test rig for hydrodynamic radial bearings under conditions representative of the expected applications for the bearing in water turbines. Bearings made from the polymer material PEEK (polyether ether ketone) were tested under static...
-
WEAR OF Si OR B DOPED AMORPHOUS CARBON COATINGS
PublikacjaThe paper describes a complex wear research on DLC (amorphous carbon) moped with boron (B) and silicone (Si). The tests were carried out in two different sliping systems: flat–on–flat (ring contact, unidirectional sliding) and ball–on–flat (reciprocating sliding). Water and medical saline solutions were used as lubricants. A comparative analysis of the results revealed differences in the initiation and progress of wear and the...
-
Fast determination of bisphenol A in spiked juice and drinking water samples by pipette tip solid phase extraction using cobalt metal organic framework as sorbent
Publikacja -
THE DETERMINATION OF ABRASION RESISTANCE OF SELECTED BIOMATERIALS FOR THE FRICTION PAIRS IN THE HIP JOINT ENDOPROSTHESIS
PublikacjaThe key requirement for the modern endoprosthesis is high durability of the friction components, which results in long and trouble-free operation in the human body. The durability of currently used endoprosthesis is often limited by tribological wear processes of friction components (e.g. between the head and the acetabular component in a hip joint endoprosthesis) [8, 19, 23, 24]. In order to compare the tribological wear, tribological...
-
Effect of presence of lifting pocket on the THD performance of a large tilting-pad thrust bearing
PublikacjaHydrostatic assistance is a commonly used method to improve limited load carrying ability of tiltingpad thrust bearings during transient states of operation of vertical shaft hydro-generators. Despite of special hydraulic equipment (as pumps, valves, etc.), it also requires manufacturing of special recesses/pockets at pad sliding surfaces, into which oil is injected under high pressure. It allows to lift the rotor before start-up...
-
Influence of permanent magnetic field on wear performance of dry sliding contacts
PublikacjaResults of experimental studies concerning the influence of permanent magnetic field on wear of dry sliding contact are presented.It was found that magnetic field of horizontal orientation is causing temporary reduction of material's hardness. It also facilitates and accelerates removal process of wear particles from the contact zone.Formation of bulges, consisting of accumulated and compacted anti-ferromagnetic material produced...
-
Tilting pad thrust bearing with novel material selection - experimental comparison of low and medium speed operation
PublikacjaThe advances in material engineering led to the development of hard carbon based coatings applied in numerous applications in order to prevent or minimize wear of the parts in contact. With Triondur® coatings, the bearing company Schaeffler has succeeded in halving the friction losses in the valve trains of passenger cars. The coatings are optimized for high abrasive wear protection and low sliding friction moments. Altogether...
-
Corrosion and Cavitation Resistances of Low Alloy Steel After Frictional-Mechanical Treatment
PublikacjaPaper presents the results of the studies of wear, corrosion and cavitation resistances of the S355J2 low alloy medium carbon steel subjected to surface modification by friction-mechanical treatment, as tested in sea water simulated solution. To evaluate the effect of the surface treatment, the comparative studies of the corrosive properties of the steel before and after treatment have been considered. The treatment due to a severe...
-
Investigation of the thermal effects in water-lubricated journal bearings with axial grooves
PublikacjaWater-lubricated hydrodynamic journal bearings are frequently applied as stern tube bearings due to their advantages over other bearing types. They are environmentally friendly, can operate without sealings and in conditions of low friction losses. The most popular are bearings with open axial grooves, which require, for proper operation, forced axial flow of the lubricating water. Correctly designed and operated stern tube bearings...
-
Analysis of radiometric signal in sedimentating suspension flow in open channel
PublikacjaThe article discusses issues related to the estimation of the sedimentating solid particles average flow velocity in an open channel using radiometric methods. Due to the composition of the compound, which formed water and diatomite, received data have a very weak signal to noise ratio. In the process analysis the known determining of the solid phase transportation time delay the classical cross-correlation function is the most...
-
Multi Parameter Sliding Test Result Evaluation for The Selection of Material Pair for Wear Resistant Components of a Hydraulic motor Dedicated for Use With Environmentally Friendly Working Fluids
PublikacjaIn the paper the method and results are presented of the testing of tribological performance of a number of hard materials available commercially. The tests consisted in unidirectional sliding with liquid lubrication. The load and velocity regime chosen were similar to a standard four-ball lubricity test with constant velocity and load increasing over time. The regime was modified in such a way that over the initial part of the...
-
Wear Resistance Enhancement of Al6061 Alloy Surface Layer by Laser Dispersed Carbide Powders
PublikacjaIn this paper, results of the experimental study on improving wear resistance in sliding friction of Al-based alloy are presented. The technique used involves the formation of a metal matrix composite (MMC) in the alloy surface layer by laser dispersion of carbide powders such as WC, TiC and SiC. For WC and TiC MMC surface coatings fabricated under conditions typical for most of the technologically relevant solid-state lasers (wavelength...
-
INVESTIGATION OF JOURNAL SLIDE BEARINGS UNDER THE ANGLE OF THEIR FUNCTIONING
PublikacjaPaper presents the structure and principle of operation of a stand for measurements of influence of the lubrication method and process on functioning of journal slide bearings in their various technical states. Measurements performed on the stand make it possible to take advantage of the new method of evaluating the influence of physical and chemical properties of lubricating oil on the coefficient of friction in the mixed friction...
-
IDENTIFICATION OF THE INTERFECE OF LATERAL SLIDE BEARINGS
PublikacjaIn the paper, the model of slide bearings of motor engine, the metodology of research on this type of bearings and its results are presented measurement standpoint consisting of main elements of Briggs & Stratton 550 serie 10 T 802 model piston motor engine driven by three phase elektric engine is introduced . On the measurement standpoint are measurements were done, needed for specification...
-
A pin-on-disc study of airborne wear particle emissions from studded tyre on concrete road contacts
PublikacjaStudded tyres wear surfaces of winter roads, generating inhalable airborne particles. In this study, four concrete road materials and two stud geometries were investigated in terms of wear, road material hardness and airborne particle concentration. The sliding contact between studded tyres and road materials was studied using a pin-on-disc machine in a clean chamber. The results show that the normal load and the stud size have...
-
An inclination in Thermal Energy Using Nanoparticles with Casson Liquid Past an Expanding Porous Surface
PublikacjaPhysical aspects of inclined MHD nanofluid towards a stretching sheet embedded in a porous medium are visualized. Two types of nanoparticles are used named as copper and alumna dioxide with water as base fluid. Similarity transformations are used to convert the partial differential equations into the set of ordinary differential equation. Closed solutions are found to examine the velocity and the temperature profiles. It is examined...
-
Dynamics Conscious Approach to Tribometer Design and Tribo-testing
PublikacjaIn the paper findings are discussed on the issue of dynamic characteristics of a tribometer as a factor influencing the result of the tribological experiment. An advanced approach to tribo-testing is attempted with integrated dynamic analysis of the tribometer and the sliding pair. The fundamental idea is explored of the tribometer being regarded as any machine in which friction is inflicted with all the resulting consequences...
-
Optimization of Single-Sided Lapping Kinematics Based on Statistical Analysis of Abrasive Particles Trajectories
PublikacjaThe chapter presents the influence of selected kinematic parameters on the geometrical results of the single-sided lapping process. The optimization of these parameters is aimed at improving the quality and flatness of the machined surfaces. The uniformity of tool wear was assumed as main optimization criterion. Lapping plate wear model was created and in detail was analyzed. A Matlab program was designed to simulate the abrasive...
-
Tribological model of porous bearings with particular attention given to the lubricant lubricity
PublikacjaThe friction and wear problems, accompanying all the tribological systems, lead to reduced service life. In order to prevent such situation, it is necessary to maintain fluid friction, which improves durability of all friction nodes in a tribological system. In the paper, the tribological system consists of porous bearings and the model deals with their weakest spots - the oil outflow points in the porous wall. A kinetic model...
-
Experimental comparison of the transition speed of a hydrodynamic journal bearing lubricated with oil and magnetorheological fluid
PublikacjaA journal bearing test bench is used to find the transition speed between the hydrodynamic and mixed lubrication regimes for a modified magnetorheological (MR) fluid. It is shown that the transition speed of the bearing can be reduced by applying a local magnetic field near minimum film when it is lubricated with the MR fluid, and that this will only marginally increase friction. The lubricating performance of the MR fluid is compared...
-
Experimental study on the feasibility of alternative materials for tilting pad thrust bearings operating in transition to mixed friction
PublikacjaIn hydrodynamic bearings traditional bearing alloys: Babbitts and bronzes are most frequently utilized. Polymer sliding layers are sometimes applied as a valuable alternative. Hard diamond-like carbon (DLC) coatings, which are also considered for certain applications may show some advantages, as well. Although material selection is of secondary importance in a full film lubrication regime it becomes important in mixed friction...
-
Ecological bearing systems for water turbines – research and development at Gdansk University of Technology
PublikacjaIncreasing requirements for environmental protection make it necessary to introduce new materials and designs. Hydroelectric power plants operating in direct contact with water reservoirs and rivers are potentially endangering water cleanliness, hence they should also be modernized in the way minimizing the environmental hazards. A lot of progress in this field has been achieved in last decades, but still there is much work to...
-
The Impact Of The Selected Parameters Of Fdm Manufacturing Technology On Tribological Performance Of Abs–Steel Pair Under Dry Friction
PublikacjaThe paper presents the result of tribological test of ABS and steel samples sliding under dry friction. Polymeric samples were manufactured of ABS material using FDM technology. Testing was carried out in unidirectional sliding in a ring-on-flat contact in a PT-3 tribometer. The scope of tested parameters included volumetric and mass wear, the friction coefficient, and polymeric specimen temperature. Polymeric specimens used in...
-
The abrasive wear resistance of coatings manufactured on high-strength low-alloy (HSLA) offshore steel in wet welding conditions
PublikacjaSome marine and offshore structure elements exploited in the water cannot be brought to the surface of the water as this will generate high costs, and for this reason, they require in-situ repairs. One of the repair techniques used in underwater pad welding conditions is a wet welding method. This paper presents an investigation of the abrasive wear resistance of coatings made in wet welding conditions with the use of two grades...
-
Preparation and Characterization of Diamond-like Carbon Coatings for Biomedical Applications—A Review
PublikacjaDiamond-like carbon (DLC) films are generally used in biomedical applications, mainly because of their tribological and chemical properties that prevent the release of substrate ions, extend the life cycle of the material, and promote cell growth. The unique properties of the coating depend on the ratio of the sp3/sp2 phases, where the sp2 phase provides coatings with a low coefficient of friction and good electrical conductivity,...
-
Emission of 1.3–10 nm airborne particles from brake materials
PublikacjaOperation of transport vehicle brakes makes a significant contribution to airborne particulate matter in urban areas, which is subject of numerous studies due to the environmental concerns. We investigated the presence and number fractions of 1.3–10 nm airborne particles emitted from a low-metallic car brake material (LM), a non-asbestos organic car brake material (NAO) and a train brake cast iron against a cast iron. Particles...
-
A Multi Rig Screening Test for Thin Ceramic Coatings in Bio - Tribological Applications
PublikacjaA method is presented for the comparative testing of wear resistance of ceramic coatings made from materials potentially feasible in tribo - medical applications, mainly orthopaedic implants made from ceramics coated metals for low cost, long life and low wear particle emission into the body. The method was devised as the main tool for use in research and is comprised of flat on flat and ball on flat surface (sliding) tests. Seven...
-
Ocena odporności na zużycie ścierne stopów Ti na elementy pary trącej endoprotez stawu kolanowego
PublikacjaNajczęściej stosowanym biomateriałem tytanowym na elementy endoprotez stawu kolanowego jest stop Ti6Al4V. Z uwagi na zawartość wanadu, zaliczanego do pierwiastków o dużej toksyczności podejmowane są działania w kierunku zastąpienia wskazanego stopu - stopami bezwanadowymi. Jednym z najbardziej obiecujących jest stop Ti13Nb13Zr zawierający w swoim składzie jedynie pierwiastki witalne, niewywołujące stanów zapalnych i odczynów...
-
Tribological Properties of Ni-P/Si3N4 Nanocomposite Layers Deposited by Chemical Reduction Method on Aluminum Alloy AW-7075
PublikacjaThe article presents the results of tribological tests of Ni-P/Si3N4 nanocomposite and Ni-P nickel layers deposited on the AW-7075 aluminum alloy by chemical reduction method, and the AW-7075 alloy without coating. Nanocomposite layers were produced using Si3N4 siliconnitride in the form of a polydisperse powder whose particle sizes ranged from 20 to 25 nm. The influence of the content of the dispersion phase layer material on...
-
Properties comparison of rubber and three layer PTFE-NBR-bronze water lubricated bearings with lubricating grooves along full bush circumference based on experimental tests
PublikacjaWater lubricated bearings have been in industrial use for well over a century. During the last decade their traditional range has been expanded with new, modern products. Despite that fact, certain solutions continue to employ the standard rubber bearing with lubricating grooves located along entire bush circumference. The work presents experimental research conducted on comparable sliding bearings with lubrication grooves along...
-
Wysokociśnieniowe uszczelnienia ruchu obrotowego wału hydraulicznych maszyn wyporowych
PublikacjaW artykule przedstawiono wyniki badań mające na celu wytypowanie węzła uszczelniającego wał silnika hydraulicznego zapewniającego najwyższą trwałość przy smarowaniu wodą. Parametry pracy: ciśnienie 2 MPa i minimalna prędkość poślizgu uszczelek 2 m/s. Opisano również nowatorski przyrząd, na którym przeprowadzono pomiary wszystkich parametrów węzła uszczelniającego.
-
A comparative performance assessment of a hydrodynamic journal bearing lubricated with oil and magnetorheological fluid
PublikacjaThis work presents the investigation results of a journal bearing lubricated with magnetorheological fluid that is activated by a local constant magnetic field to vary both the local flow resistance and pressure. The bearing performance is assessed via Finite Element Modelling (FEM) and results are corroborated by experiments. The FEM model uses the Bingham model to describe the fluid film. A dedicated test rig is used to assess...
-
Influence of Wastewater Treatment Technology on Particle Size Distribution in the Effluent
PublikacjaSuspended solids in water and wastewater usually carry quite a large load of pollutants (organic substances, nutrients, heavy metals, etc.) adsorbed on the particles surface. Particles of different sizes carry different types and quantities of pollutants. Therefore, particle size distribution is of importance in waster and wastewater treatment. In the article the influence of different treatment technologies on particle size distribution...