Filtry
wszystkich: 320
wybranych: 302
Wyniki wyszukiwania dla: RECYCLING WASTE RUBBER ELASTOMER BLENDS BUTYL RUBBER FILLER
-
Alkali-activated slag (AAS) and OPC-based composites containing crumb rubber aggregate: Physico-mechanical properties, durability and oxidation of rubber upon NaOH treatment
Publikacja -
Modification of Ground Tire Rubber—Promising Approach for Development of Green Composites
Publikacja -
Characteristic of elastomers from the rubber mixtures (NR) containing devulcanizate compounds
PublikacjaW pracy omówiono wyniki badań elastomerów otrzymanych w procesie wulkanizacji mieszanek kauczukowych napełnionych kredą i dodatkowo zawierających różne udziały dewulkanizatu. Dewulkanizaty natomiast otrzymano z pyłu gumowego metodą termomechaniczną. Otrzymane elastomery poddano badaniom w warunkach statycznych i przeprowadzono je na maszynie wytrzymałościowej. Określono wpływ czasu wulkanizacji, ilości napełniacza mineralnego oraz...
-
Properties comparison of rubber and three layer PTFE-NBR-bronze water lubricated bearings with lubricating grooves along full bush circumference based on experimental tests
PublikacjaWater lubricated bearings have been in industrial use for well over a century. During the last decade their traditional range has been expanded with new, modern products. Despite that fact, certain solutions continue to employ the standard rubber bearing with lubricating grooves located along entire bush circumference. The work presents experimental research conducted on comparable sliding bearings with lubrication grooves along...
-
Determining the Mechanical Properties of Solid Plates Obtained from the Recycling of Cable Waste
Publikacja -
Kompozyty poliuretanowo-gumowe wulkanizowane siarką = Polyurethane-rubber composites vulcanization of sulphur
PublikacjaW artykule przedsawiono wyniki badań statycznych i dynamicznych właściwości mechanicznych oraz analizę mikroskopową nowych kompozytowych materiałów poliuretanowo-gumowych wulkanizowanych siarką otrzymanych z kauczuków uretanowych wulkanizowanych siarką i recyklatu gumowego w postaci granulatu o wielkości ziarna do 1 mm uzyskanego z poużytkowych opon samochodowych. Osnowy poluretanowe napełniano recyklatem w ilościach od 10 do 80%...
-
Influence of manganese(II) silanethiolate with 1,10-phenathroline on properties of natural rubber vulcanizates
PublikacjaW komunikacie zaprezentowano wstępne wyniki badań dotyczących wpływu kompleksu [Mn{SSi(OBu-t)3}2(phen)] na właściwości wulkanizatów gumowych z kauczuku naturalnego. Przeprowadzone badania sugerują, że chociaż związek ten nie działa bezpośrednio jako przyspieszacz, to aktywuje wulkanizację przy użyciu tiuramu.
-
Sustainable recycling of waste polystyrene into hierarchical porous carbon nanosheets with potential applications in supercapacitors
Publikacja -
Chemical recycling of plastic waste as a mean to implement the circular economy model in the European Union
Publikacja -
Thermomechanical reclaiming of ground tire rubber via extrusion at low temperature: Efficiency and limits
Publikacja -
Recycled polyethylene and crumb rubber composites modified asphalt with improved aging resistance and thermal stability
Publikacja -
Processing, physico-mechanical and thermal properties of reclaimed GTR and NBR/reclaimed GTR blends as function of various additives
PublikacjaIn this work, ground tire rubber (GTR) was mechano-chemically reclaimed in the presence of bitumen and various additives. During studies three types of processing and curing additives: (i) peptizer P300; (ii) vulcanization accelerator tetramethylthiuram disulfide (TMTD) and (iii) organic peroxide di(2-tert-butyl-peroxyisopropyl)benzene (BIB1) were applied to enhance reclaiming of GTR. Reclaiming process was evaluated by oscillating...
-
An experimental assessment on a diesel engine powered by blends of waste-plastic-derived pyrolysis oil with diesel
PublikacjaThe utilization of plastic solid wastes for sustainable energy production is a crucial aspect of the circular economy. This study focuses on pyrolysis as an effective method to convert this feedstock into renewable drop-in fuel. To achieve this, it is essential to have a comprehensive understanding of feedstock composition, pyrolysis process parameters, and the physicochemical characteristics of the resulting fuel, all correlated...
-
The impedance method of monitoring the degradation of rubber linings in applications where progressive deterioration is the predominant failure mechanism
Publikacja -
Pyrolysis Process of Whole Waste Tires as A Biomass Energy Recycling / Piroliza Opon Samochodowych Jako Energetyczny Recykling Biomasy
Publikacja -
Polyurethane glycolysate from industrial waste recycling to develop low dielectric constant, thermally stable materials suitable for the electronics
PublikacjaWe are utilizing a new method to improve the dielectric properties of a conventional polymer using a recycled polymer product. The polyurethane foams are recycled by glycolysis process and the derived material was applied to improve the dielectric properties of the brittle DGEBA epoxy resin. Two main parameters that determine the applicability of the material as a dielectric (the dielectric constant and dielectric loss), were studied...
-
Artificial neural networks as a tool for selecting the parameters of prototypical under sleeper pads produced from recycled rubber granulate
Publikacja -
Inspection of rubber linings operating in flue gas desulphurisation units. Inspekcje wykładzin gumowych w warunkach instalacji odsiarczania spalin.
PublikacjaPomiary metodą EIS wykładzin gumowych przeprowadzono w warunkach polowych.Stwierdzono, że najlepszym miernikiem jakości powłoki jest pojemność elektryczna powłoki. Sposób wyznaczania zwartości wilgoci w powłoce oparty został na równaniu Brashera-Kingsbury´ego. Wyniki porównano z oznaczeniami wilgoci w wykładzinie metodami niszczącymi przeprowadzonymi w tych samych miejscach co badania elektrochemiczne.
-
Experimental research on water lubricated three layer sliding bearing with lubrication grooves in the upper part of the bush and its comparison with a rubber bearing
Publikacjacomposite. Eachofitslayershasanimportantfunction.Speciallypreparedslidingsurfaceensures minimum resistance.Followingrunning-initssmoothnessbecomesveryhighandthebearingmay continue workingunder fluid lubricationregime.NBRlayerensuresbearingelasticity,goodvibration damping propertiesandinsusceptibilitytoshaftaxismisalignment.Theexternalbrasslayermakes fitting thebearingeasier. Experiment resultsoftheconductedresearchwerecomparedwiththoseforarubberbearingof similar...
-
The influence of feed rate and shear forces on the devulcanization process of ground tire rubber (GTR) conducted in a co-rotating twin screw extruder
Publikacja -
Influence of microwave treatment conditions of GTR on physico-mechanical and structural properties of NBR/NR/GTR composites
PublikacjaThe increasing amount of tires used in the industry induces the researchers to find alternatives to the recycling of the end-of-life tires. Several alternatives in order to application of ground tire rubber GTR include their incorporation as a filler in composites. The main issue in this approach is the lack of compatibility between GTR and polymer matrix. In order to solve this problem the devulcanization by microwaves has been...
-
Vegetable derived-oil facilitating carbon black migration from waste tire rubbers and its reinforcement effect
PublikacjaThree dimensional chemically cross-linked polymer networks present a great challenge for recycling and reutilization of waste tire rubber. In this work, the covalently cross-linked networks of ground tire rubber (GTR) were degraded heterogeneously under 150 °C due to the synergistic effects of the soybean oil and controlled oxidation. The degradation mechanism was discussed using Horikx theory and Fourier transformation infrared...
-
Wpływ technicznych włókien celulozowych na wybrane właściwości kompozytów kauczuku naturalnego
PublikacjaCelem niniejszej pracy było zbadanie wpływu technicznych włókien celulozowych (dodanych w ilości 10, 20, 30 i 40 phr) jako naturalnego napełniacza na wybrane właściwości kompozytów na osnowie kauczuku naturalnego. Zbadano właściwości wulkanizatów przy statycznym rozciąganiu, w próbie rozdzierności, a także twardość, elastyczność przy odbiciu oraz ścieralność otrzymanych materiałów. Wyniki badań zostały porównane z wulkanizatem...
-
Evaluation of structural change during fast transformation process of cross-linked NR into liquid NR by light pyrolysis
PublikacjaThe presence of cross-linked networks in rubber creates a tremendous problem for recycling and reusing of waste rubber. Fast transformation of cross-linked natural rubber (NR) into liquid natural rubber was carried out by light pyrolysis in temperature range from 240 to 300 °C in variable time (in range: 1–30 min). The transformation efficiency was evaluated by measuring the sol fraction and the cross-link density of the gel fraction....
-
Thermoplastic Elastomers Filled With GTR
PublikacjaIn recent years, searching for new and cost-effective methods of recycling waste tires has been a subject of research in many laboratories worldwide. This is due to regulations in the law and environmental factors, which have both stimulated industry to re-use high quality rubber found in ground tire rubber (GTR). One of the most promising solutions in this area seems to be thermoplastic elastomers (TPEs) filled with GTR, which...
-
GTR/Thermoplastics Blends: How Do Interfacial Interactions Govern Processing and Physico-Mechanical Properties?
PublikacjaIn this work, GTR/thermoplastics blends (in ratio 50/50 and 75/25 wt.%) were prepared by melt-compounding in an internal mixer. During research, trans-polyoctenamer rubber (TOR), ethylene-vinyl acetate copolymer (EVA), ethylene-octene copolymer (EOC), and linear low-density polyethylene (LLDPE), were used in their thermoplastic phase. Microstructure and processing-performance property interrelationships of the studied materials...
-
Morphology and mechanical properties of polyamide/clay nanocomposites toughened with NBR/NBR-g-GMA: A comparative study
PublikacjaThis work highlights the importance of nanoclay dispersion state in the nanocomposites containing polyamide 6 (PA6), nanoclay and elastomers as well as clay localization at the interface of thermoplastic/elastomer. Morphology and mechanical properties of a series of nanocomposites containing acrylonitrile butadiene rubber (NBR), glycidyl methacrylate-grafted NBR (NBR-g-GMA), and combined NBR/NBR-g-GMA were compared and discussed...
-
Wpływ polietylenu szczepionego bezwodnikiem maleinowym oraz sił ścinających na właściwości mieszanin polietylen wysokiej gęstości-miał gumowy
PublikacjaScharakteryzowano wpływ kompatybilizatora w postaci polietylenu szczepionego bezwodnikiem maleinowym na właściwości mieszanin PE-HD–miał gumowy. Kompozycje termoplastyczne zawierające 50 cz. mas. rozdrobnionych odpadów gumowych, otrzymano przy użyciu współbieżnej wytłaczarki dwuślimakowej. Poziom sił ścinających generowanych podczas mieszania, regulowano za pomocą zmian prędkości obrotowych ślimaków. Przeprowadzono charakterystykę...
-
Progress in used tyres management in the european union: a review
PublikacjaThe dynamic increase in the manufacture of rubber products, particularly those used in the automobile industry, is responsible for a vast amount of wastes, mostly in the form of used tyres, of which more than 17 million tonnes are produced globally each year. The widely differing chemical compositions and the cross-linked structures of rubber in tyres are the prime reason why they are highly resistant to biodegradation, photochemical...
-
iPP/HDPE blends compatibilized by a polyester: An unconventional concept to valuable products
PublikacjaPolyolefins are the most widely used plastics accounting for a large fraction of the polymer waste stream. Although reusing polyolefins seems to be a logical choice, their recycling level remains disappointingly low. This is mainly due to the lack of large-scale availability of efficient and inexpensive compatibilizers for mixed polyolefin waste, typically consisting of high-density polyethylene (HDPE) and isotactic polypropylene...
-
Nonlinear Viscoelastic Properties of Polyurethane Nanocomposites
PublikacjaIn recent years, the nonlinear viscoelastic behaviors of elastomeric nanocomposites have been examined, especially for a wide range of rubbery composite (including natural rubber) materials. This chapter describes the influence of fillers and nanofillers on the nonlinear viscoelastic properties of elastomeric polyurethane systems. These filled elastomers (similar to the classic natural rubber reinforced elastomers), also exhibit...
-
Evaluation and rationale of the performance of several elastomeric composites incorporating devulcanized EPDM
Publikacjathylene Propylene Diene rubber (EPDM), is present in many applications. However, its crosslinked structure makes difficult its recycling. The use of devulcanized EPDM, (dEPDM) as a component of elastomeric composites, is a real possibility to reuse EPDM scraps. In this study, three matrices (natural rubber (NR), styrene butadiene rubber (SBR) and EPDM rubber) have been tested including devulcanized EPDM as a recycled component....
-
A Review of Hyperelastic Constitutive Models for Dielectric Elastomers
PublikacjaDielectric elastomers are smart materials that are essential components in soft systems and structures. The core element of a dielectric elastomer is soft matter, which is mainly rubber-like and elastomeric. These soft materials show a nonlinear behaviour and have a nonlinear strain-stress curve. The best candidates for modelling the nonlinear behaviour of such materials are hyperelastic strain energy functions. Hyperelastic functions...
-
Influence of the Addition of Recycled Aggregates and Polymer Fibers on the Properties of Pervious Concrete
PublikacjaThe aim of the study was to check the possibility of reusing aggregate from recycled concrete waste and rubber granules from car tires as partial substitution of natural aggregate. The main objective was to investigate the effects of recycled waste aggregate modified with polymer fibers on the compressive and flexural strength, modulus of elasticity and permeability of pervious concrete. Fibers with a multifilament structure and...
-
Reactive extrusion of bio-based polymer blends and composites – Current trends and future developments
PublikacjaReactive extrusion is a cost-effective and environmentally-friendly method to produce new materials with enhanced performance properties. At present, reactive extrusion allows in-situ polymerization, modification/functionalization of polymers or chemical bonding of two (or more) immiscible phases, which can be carried out on commonly used extrusion lines. Although reactive extrusion has been known for many years, its application...
-
To what extent can hyperelastic models make sense the effect of clay surface treatment on the mechanical properties of elastomeric nanocomposites?
PublikacjaThe poor knowledge about nonlinear mechanical behavior of elastomer nanocomposites arises from the incomplete information on the interface. Application of hyperelastic models provides more insights into the nature and the situation of interaction between the elastomeric matrix and nanofillers. The current work seeks to address the effect of interphase strength on tensile properties of the elastomer nanocomposites under large deformations....
-
Towards understanding the role of peroxide initiators on compatibilization efficiency of thermoplastic elastomers highly filled with reclaimed GTR
PublikacjaThermoplastic elastomers based on recycled high density polyethylene (rHDPE) and styrene-butadiene-styrene (SBS) block copolymer were highly filled with reclaimed ground tire rubber (RR). The impact of various organic peroxides (dicumyl peroxide (DCP), benzoyl peroxide (BP) and di-tert-butyl peroxide (DB)), applied as free-radical initiators, on the processing, structure and performance properties of rHDPE/SBS/RR blends was investigated....
-
Study on polymer modified road asphalt mixture
PublikacjaThe formulation of ternary asphalt-additives blend composed of crumb rubber : low-density polyethylene (CR : LDPE) and crumb rubber : textile fiber (CR : TF) couples, and quaternary asphalt additives-blend composed of (CR : LDPE : TF) triplets on the virgin asphalt to optimize the asphalt basic and rheological properties and to use the extrusion process of two or three additives to obtain composite materials of them, as well as...
-
Structure-property relationships in peroxide-assisted blends of poly(ε-caprolactone) and poly(3-hydroxybutyrate)
PublikacjaPoly(ε-caprolactone) and poly(3-hydroxybutyrate) (PCL/PHB) blends in two weight ratios (75/25 and 50/50) were reactively compatibilized in the presence of di-(2-tert-butyl-peroxyisopropyl)-benzene and dicumyl peroxide as free radical initiators. Rheological, mechanical, thermal properties and morphological features, as well as the chemical structure of PCL/PHB blends were investigated. It was found that regardless of PCL/PHB blend...
-
Evaluation of Low Temperature Properties of Rubberized Asphalt Mixtures
PublikacjaThe paper presents low-temperature test results of asphalt mixtures designed with use of bitumen modified by crumb rubber and also SBS polymer. Laboratory tests were conducted on two types of asphalt mixtures for wearing course – stone matrix asphalt (SMA 8) and porous asphalt (PA 8). This paper presents results of the following laboratory tests at low temperatures: TSRST test, three point bending creep test, fracture toughness...
-
Cross-Linking, Morphology, and Physico-Mechanical Properties of GTR/SBS Blends: Dicumyl Peroxide vs. Sulfur System
PublikacjaIn this work, ground tire rubber and styrene–butadiene block copolymer (GTR/SBS) blends at the ratio of 50/50 wt%, with the application of four different SBS copolymer grades (linear and radial) and two types of cross-linking agent (a sulfur-based system and dicumyl peroxide), were prepared by melt compounding. The rheological and cross-linking behavior, physico-mechanical parameters (i.e., tensile properties, abrasion resistance,...
-
Mechanical Performance and Environmental Assessment of Sustainable Concrete Reinforced with Recycled End-of-Life Tyre Fibres
PublikacjaThe presented research’s main objective was to develop the solution to the global problem of using steel waste obtained during rubber recovery during the tire recycling. A detailed comparative analysis of mechanical and physical features of the concrete composite with the addition of recycled steel fibres (RSF) in relation to the steel fibre concrete commonly used for industrial floors was conducted. A study was carried out using...
-
Assessment of the devulcanization process of EPDM waste from roofing systems by combined thermomechanical/microwave procedures
PublikacjaEthylene-propylene-diene rubber (EPDM) is a elastomer widely used in common industrial applications. EPDM can be shaped into sheets and employed as isolating material for roofing systems. In this study, scraps of EPDM from commercial, industrial and residential roofing systems were treated by combined thermo-mechanical and microwave devulcanization processes including peroxide of benzoyl (BPO). The devulcanized EPDM (Dev-EPDM)...
-
Emission and properties of airborne wear particles from train brake friction materials based on novolac phenolic resins and butadiene rubbers
PublikacjaThe emission of airborne particulate matter from a train brake depends on the formulation of its friction material. This study investigates the emission and properties of wear particles from train brake friction materials based on straight or resorcinol-modified novolac phenolic resin and nitrile or styrene butadiene rubber used as binding ingredients. The wear particles are generated by a pin-on-disc tribomachine inside an aerodynamic...
-
Applications of permeability, oedometer and direct shear tests to the sand mixed with waste tire crumb
PublikacjaThe amount of the used waste rubbers in the world has been increasing every year, and their utilization, become a major environmental problem worldwide. The present experimental work has been performed to investigate the influence of rubber inclusion on the behavior of a sand. Geotechnical properties of the sand, and sand with tire crumb at various ratios mixtures (0%, 2.5%, 7.5%, and 15%) were investigated through a series of...
-
Sustainable Strategy for Algae Biomass Waste Management via Development of Novel Bio-Based Thermoplastic Polyurethane Elastomers Composites
PublikacjaThis work concerns the waste management method of algae biomass wastes (ABW). For this purpose, we prepared bio-based thermoplastic polyurethane elastomer (bio-TPU) composites. Algae biomass wastes are derived from algal oil extraction of Chlorella vulgaris and from biomass of Enteromorpha and Zostera marina. ABWs were used in the bio-TPUs composites as a filler in the quantity of 1, 5, 10, and 15 wt.%. The bio-based composites...
-
Risks related to car fire on innovative Poroelastic Road Surfaces-PERS
PublikacjaTo reduce tyre/road noise, the concept of poroelastic road surfaces (PERS) was invented. PERS is a road surface material that is porous, and at the same time, it is flexible because of the substantial amount of rubber granulate content (from 20% to 85%). The rubber and stone particles are bound by polyurethane resin instead of bitumen. It was feared that in case of fire, because of the high content of rubber and polyurethane, there...
-
A recent developments in polyurethane foams containing a low-cost and pro-ecological modifiers
PublikacjaDiversity of the polyurethane (PU) foams applications cause that investigation of the relationships between their structure and properties is currently very popular topic among the many research institutions and companies. At the turn of the last years many scientific papers about PU foams and their composites were published. The one of the main research trends in this field is related to the reduction of production costs of...
-
Morphology, Thermo-Mechanical Properties and Biodegradibility of PCL/PLA Blends Reactively Compatibilized by Different Organic Peroxides
PublikacjaReactive blending is a promising approach for the sustainable development of bio-based polymer blends and composites, which currently is gaining more and more attention. In this paper, biodegradable blends based on poly(ε-caprolactone) (PCL) and poly(lactic acid) (PLA) were prepared via reactive blending performed in an internal mixer. The PCL and PLA content varied in a ratio of 70/30 and 55/45. Reactive modification of PCL/PLA...
-
Modyfikacja kompozytów elastomerowych NR za pomocą ligniny i glicerolizatu
PublikacjaPrzedmiotem opisanych w niniejszym artykule badań są wulkanizaty kauczuku naturalnego. Celem pracy było zbadanie wpływu ligniny oraz glicerolizatu na wybrane właściwości kompozytów zawierających kauczuk naturalny. Strukturę chemiczną przygotowanych materiałów potwierdzono, wykorzystując analizę spektroskopową w podczerwieni (FTIR). Zbadano również właściwości mechaniczne przy statycznym rozciąganiu, twardość, ścieralność oraz odbojność...