Wyszukiwarka
Filtry
wszystkich: 276
wybranych: 245
Filtry wybranego katalogu
Wyniki wyszukiwania dla: BENDING TEST
-
Coda wave interferometry in monitoring the fracture process of concrete beams under bending test
PublikacjaEarly detection of damage is necessary for the safe and reliable use of civil engineering structures made of concrete. Recently, the identification of micro-cracks in concrete has become an area of growing interest, especially using wave-based techniques. In this paper, a non-destructive testing approach for the characterization of the fracture process was presented. Experimental tests were made on concrete beams subjected to mechanical...
-
Three-point bending test of sandwich beams supporting the GFRP footbridge design process - validation
PublikacjaSome selected aspects concerning material and construction design issues for pedestrian footbridge made of GFRP composite materials are elaborated in this paper. The analysis is focused on validation tests, which are particularly important because of the advanced technology and materials that are used for this innovative bridge. The considered footbridge is a sandwich-type shell structure comprising of PET foam core and outer skins...
-
Local and global response of sandwich beams made of GFRP facings and PET foam core in three point bending test
PublikacjaIn the paper behaviour of laminated sandwich beams (FRP face sheet – PET foam core – FRP face sheet) subjected to three point bending is studied. The paper aim is to find practical descriptions enabling effective and accurate estimation of the elastic response, damage and failure of the beams, basing on experiments and static calculations. Therefore a number of tests are described, that were done on laminated coupons and foam specimens...
-
Influence of Wood Moisture on Strength and Elastic Modulus for Pine and Fir Wood Subjected to 4-point Bending Tests
PublikacjaThe main purpose of this research paper was to determine the influence of the wood moisture on the strength and elastic modulus of pine and fir wood specimens subjected to the 4-point bending tests. Six bending tests for each wood species and for two different moisture level have been performed. Then, the advanced statistical analysis of the results has been carried out. On the basis of the obtained results, it has been noted that...
-
Testing of low temperature behaviour of asphalt mixtures in bending creep test
PublikacjaThe paper presents a method of bending beam test and its importance for evaluation of asphalt mixtures behaviour at low temperatures. Two types of asphalt mixtures: asphalt concrete AC with normal paving grade bitumen and stone mastic asphalt SMA with SBS-modified bitumen were tested. Long-term oven ageing (LTOA) test was also used in the laboratory according to SHRP procedure. The Burgers model was applied and rheological parameters...
-
Assessment of Thermal Stresses in Asphalt Mixtures at Low Temperatures Using the Tensile Creep Test and the Bending Beam Creep Test
PublikacjaThermal stresses are leading factors that influence low-temperature cracking behavior of asphalt pavements. During winter, when the temperature drops to significantly low values, tensile thermal stresses develop as a result of pavement contraction. Creep test methods can be suitable for the assessment of low-temperature properties of asphalt mixtures. To evaluate the influence of creep test methods on the obtained low-temperature...
-
Evaluation of Asphalt Mixture Low-Temperature Performance in Bending Beam Creep Test
PublikacjaLow-temperature cracking is one of the most common road pavement distress types in Poland. While bitumen performance can be evaluated in detail using bending beam rheometer (BBR) or dynamic shear rheometer (DSR) tests, none of the normalized test methods gives a comprehensive representation of low-temperature performance of the asphalt mixtures. This article presents the Bending Beam Creep test performed at temperatures from −20...
-
A new anisotropic bending model for nonlinear shells: Comparison with existing models and isogeometric finite element implementation
PublikacjaA new nonlinear hyperelastic bending model for shells formulated directly in surface form is presented, and compared to four existing prominent bending models. Through an essential set of elementary nonlinear bending test cases, the membrane and bending stresses of each model are examined analytically. Only the proposed bending model passes all the test cases, while the other bending models either fail or only pass the test cases for...
-
ATTEMPT AT EVALUATING THE INFLUENCE OF BENDING STRESS ON SHAFT WEAR PROCESSES IN WATER LUBRICATED SLIDING BEARING WITH A RUBBER BUSHING
PublikacjaWater lubricated bearings find increasingly wide application in shipbuilding or hydro–power industry, the popularity stemming from their numerous advantages. Unfortunately, as it turns out, water lubricated bearings do not always meet expectations, as on occasion they become subject to intense, premature wear which requires costly repair. One of the still unexplained phenomena is the process of excessive bearing wear, in particular...
-
Assessment of crack resistance of S355J2+N steel according to SEP 1390 standard
PublikacjaThe aim of the study was to evaluate the weldability of S355J2+N steel by bending test according to SEP 1390. In the specimen from S355J2+N steel 3 external cracks were found, 1 of which were stopped in the fusion line and 2 in heat affected zone. Results of bending test for investigated grade of steel are positive.
-
Influence of Bitumen Type and Asphalt Mixture Composition on Low-Temperature Strength Properties According to Various Test Methods
PublikacjaIn regions with low-temperatures, action transverse cracks can appear in asphalt pavements as a result of thermal stresses that exceed the fracture strength of materials used in asphalt layers. To better understand thermal cracking phenomenon, strength properties of different asphalt mixtures were investigated. Four test methods were used to assess the influence of bitumen type and mixture composition on tensile strength properties...
-
Development and application of asphalt binder relaxation test in different dynamic shear rheometers
PublikacjaIn this study, a novel relaxation test is proposed to evaluate asphalt binder low temperature properties using a Dynamic Shear Rheometer (DSR) with parallel plates of 4 mm in diameter. Three rheometers from three different manufacturers are used to analyze seven asphalt binders. Different material parameters are derived which are useful to evaluate and discriminate different asphalt binders. Test results of all three instruments...
-
Assessment of crack resistance of ship steels according to SEP 1390 standard
PublikacjaThe aim of the study was to evaluate the weldability of E36 nd NVE-36 steels by bending test according to SEP 1390. In the case of the specimen from E36 steel 9 external cracks were found, 5 of which were stopped in the fusion line and 4 in heat affected zone. In the case of the specimen from NVE-36 steel 8 external cracks were found, 4 of which were stopped in the fusion line and 4 in heat affected zone. Results of bending test...
-
EVALUATING THE INFLUENCE OF BENDING STRESS ON A 1H18N9 STEEL SHAFT WEAR PROCESS IN A WATER LUBRICATED SLIDING BEARING WITH A RUBBER BUSHING
PublikacjaThe issue of excessive wear of shaft journals co-working with a rubber bearing has been unexplained so far. Premature and sometimes very intensive wear of ship sliding bearings in water conditions is the reason for carry out very expensive and more frequent than expected repairs. The authors (E. Piątkowska, W. Litwin) made an attempt to find a case that influences the value of this wear described in the paper “Attempt at Evaluating...
-
Effect of polymer fibres reinforcement on selected properties of asphalt mixtures
PublikacjaThe paper presents selected results of the research program concerning fibre reinforced asphalt concrete. Aramid-polyalphaolefin fibres was used in this study. Selected properties responsible for low temperature cracking and resistance to permanent deformation are presented in this paper. Low temperature cracking susceptibility was evaluated with the results obtained from bending test of rectangular beams with constant rate of...
-
Characterization of corrosion in reinforced concrete beams using destructive and non-destructive tests
PublikacjaThe paper presents both non-destructive and destructive experimental tests on steel-reinforced concrete beams subjected to electrochemical corrosion. To examine the condition and behavior of the specimens, destructive tests were carried out, i.e., a three-point bending together with a modulated ultrasonic wave test. In addition, a series of non-destructive experiments were conducted, such as the potential measurement method, low-frequency...
-
Textile reinforced concrete members subjected to tension, bending, and in-plane loads: Experimental study and numerical analyses
PublikacjaTextile reinforced concrete has raised increasing research interest during the last years, mainly due to its potential to be used for freeform shell structures involving complex load situations. Yet, most experimental work has focused on test setups with primarily uniaxial loading. In the current work, such setups are complemented with a novel test setup of deep beams, including in-plane bending and shear. Further, nonlinear finite...
-
Fracture simulations in concrete beam under bending using a mesoscopic model with cohesive elements
PublikacjaThe main aim of this paper was to investigate a complex fracture process in a concrete beam subjected to 3-point bending test by means of the 2D meso-scale FEM with 4-node cohesive elements embedded in the initial mesh of 3-node solid elements. The material heterogeneity was taken into account by considering 3 different phases (aggregate, cement matrix, ITZs) on the basis of randomly generated internal structure of concrete and...
-
4-Point beam tensile test on a soft adhesive
PublikacjaAn adhesive butt joint with a soft bondline has been studied. A series of experiments was conducted on test pieces constituted of aluminium adherends bonded with a low modulus epoxy adhesive, ScotchWeld™ 2216. The joint was subjected to four point bending, in tension/compression loading, under constant deflection rate, with the bondline being parallel to the applied load. The objective was to examine and evaluate crack nucleation...
-
The energy approach to fatigue crack growth of S355 steel welded specimens subjected to bending
PublikacjaThe study presents the results of the research on the rate of fatigue crack growth subjected to bending in the ferritic-pearlitic structure. The studies were carried out at a constant amplitude of the moment and at various values of the load ratios R and at the operating frequency of the machine of 28.4 Hz. Flat specimens made of S355 steel and with fillet welds and with double-sided blunt external notches as well as concave...
-
The effect of external load on ultrasonic wave attenuation in steel bars under bending stresses
PublikacjaThe stress state in deformed solids has a significant impact on the attenuation of an ultrasonic wave propagating through the medium. Measuring a signal with certain attenuation characteristics can therefore provide useful diagnostic information about the stress state in the structure. In this work, basic principles behind a novel attenuation-based diagnostic framework are introduced. An experimental study on steel bars under three-point...
-
Size effect in concrete beams under bending – influence of the boundary layer and the numerical description of cracks
PublikacjaIn the paper the size effect phenomenon in concrete is analysed. The results of numerical simulations of using FEM on geometrically similar un-notched and notched concrete beams under bending are presented. Concrete beams of four different sizes and five different notch heights under three-point bending test were simulated. In total 18 beams were analysed. Two approaches were used to describe cracks in concrete. First, eXtended...
-
Cyclic behavior of FeCoCrNiMn high entropy alloy coatings produced through cold spray
PublikacjaeCoCrNiMn high entropy alloy powders were employed to produce coatings on carbon steel through high pressure cold spray (at 1100 °C and 7 MPa in temperature and pressure respectively). X-ray diffraction of the sprayed material revealed a dense coating with the retention of the original crystallographic structure. Once splatted, particles revealed high flattening ratio with consequent excellent adhesion of the coating to the substrate....
-
Experimental Tests Of Sandwich Beams In The Design Process Of GFRP Shell Footbridge Structure
PublikacjaThe paper includes selected aspects of the study to elaborate architectural, material and construction design of pedestrian footbridge spans made of composite materials. The considered footbridge is a sandwich-type shell structure. The cooperation of PET foam core with outer lining surfaces is crucial for its load bearing capacity. The paper is aimed to experimental investigation of sandwich beams subjected to bending loading....
-
Prediction of metal deformation due to line heating; an alternative method of mechanical bending, based on artificial neural network approach
PublikacjaLine heating is one of the alternative methods of forming metals and this kind of forming uses the heating torch as a source of heat input. During the process, many parameters are considered like the size of the substrate, thickness, cooling method, source power intensity, the travel speed of the power source, the sequence of heating, and so on. It is important to analyze the factors affecting the...
-
Evaluation of Low Temperature Properties of Rubberized Asphalt Mixtures
PublikacjaThe paper presents low-temperature test results of asphalt mixtures designed with use of bitumen modified by crumb rubber and also SBS polymer. Laboratory tests were conducted on two types of asphalt mixtures for wearing course – stone matrix asphalt (SMA 8) and porous asphalt (PA 8). This paper presents results of the following laboratory tests at low temperatures: TSRST test, three point bending creep test, fracture toughness...
-
Screw displacement pile shaft deformations measured by vibrating wire and fiber optic systems during a static load test
PublikacjaThis paper describes a full scale static load test performed on a 400 mm diameter screw displacement pile equipped with four different strain measuring systems. Three types of vibrating wire strain gauges (VWSG) were used: global - retrievable, local attached to steel pipe and local concrete embedded. The fourth system was distributed fiber optic sensors based on Rayleigh back scattering (DFOS) - three in the pile cross section....
-
Numerical analysis of lumbar spine injury during road safety barrier collision
PublikacjaPurpose: Enhancing road safety is a critical goal worldwide, necessitating the development of clear standards for road safety systems. This study focuses on lumbar spine (L-spine) compression injuries during collisions with concrete road safety barriers (RSBs). It aims to analyze internal forces during impact to understand L-spine injury biomechanics in such accidents. Methods: The research included a literature review, analyzing...
-
The influence of welding heat input on the quality and properties of high strength low-alloy dissimilar steel butt joints
PublikacjaThe paper presents the results of non-destructive and destructive tests of dissimilar highstrength low-alloy S460ML and S460N steel butt joints. These steels are characterized by similar mechanical properties, but their carbon equivalent CeIIW values are much different. The joints were made using different values of heat input for each welding bead. They were tested by non-destructive methods: visual, penetrant, radiographic and...
-
Influence of Selected Warm Mix Asphalt Additives on Cracking Susceptibility of Asphalt Mixtures
PublikacjaWarm mix asphalt (WMA) has been widely accepted as a future asphalt paving technology. Besides clear advantages, there are still some concerns regarding durability and long-term performance of pavements made with this type of asphalt mixtures. One of the most important issues is low temperature behaviour of WMA because certain additives used for temperature reduction can aect bitumen properties. This paper presents the evaluation...
-
Wpływ zbrojenia polimerowymi włóknami rozproszonymi na wybrane właściwości mieszanek mineralno-asfaltowych
PublikacjaW artykule przedstawiono wybrane wyniki badań mieszanek mineralno-asfaltowych zbrojonych polimerowymi włóknami rozproszonymi. Ocenie poddano mieszankę włókien zbrojących aramidowo-poliolifenowych pod kątem wpływu ich zastosowania na właściwości niskotemperaturowe i odporności na deformacje trwałe mieszanek mineralno-asfaltowych. Właściwości niskotemperaturowe oceniano na podstawie testu zginania próbek belkowych oraz na podstawie...
-
Comparison of calculated and measured thermal stresses in asphalt concrete
PublikacjaThe paper presents the comparison of calculated and measured thermal stresses induced in restrained asphalt concrete specimens by cooling. Thermal stresses were measured in the Thermal Stress Restrained Specimen Test. The calculations of thermal stresses were performed with the use of a theoretical formula based on the temperature dependent stiffness modulus. The novel approach applied in this paper was that the stiffness modulus...
-
Badania mieszanek mineralno-asfaltowych w niskiej temperaturze
PublikacjaW artykule przedstawiono metody badań w niskiej temperaturze betonu asfaltowego przeznaczonego do warstwy ścieralnej. Przedstawione zostały wyniki badań dla 4 różnych metod badawczych: zginania, pełzania, pośredniego rozciągania oraz rozciągania termicznego przy ograniczonym odkształceniu (test TSRST). Próbki betonu asfaltowego były przygotowywane w laboratorium z wykorzystaniem 3 rodzajów asfaltów: asfaltu zwykłego, asfaltu modyfikowanego...
-
Numerical simulation of asphalt mixtures fracture using continuum models
PublikacjaThe paper considers numerical models of fracture processes of semi-circular asphalt mixture specimens subjected to three-point bending. Parameter calibration of the asphalt mixture constitutive models requires advanced, complex experimental test procedures. The highly non-homogeneous material is numerically modelled by a quasicontinuum model. The computational parameters are averaged data of the components, i.e. asphalt, aggregate...
-
Autogenous Fiber Laser Welding of 316L Austenitic and 2304 Lean Duplex Stainless Steels
PublikacjaThis study presents results of experimental tests on quality of dissimilar welded joints between 316L austenitic and 2304 lean duplex stainless steels, welded without ceramic backing. Fiber laser welded butt joints at a thickness of 8 mm were subjected to non‐destructive testing (visual and penetrant), destructive testing (static tensile test, bending test, and microhardness measurements) and structure observations (macro‐ and...
-
Impact of reclaimed asphalt pavement (RAP) on low-temperature properties of asphalt concrete
PublikacjaHot mix recycling is a practice which enables reusing materials from old asphalt pavements. Current Polish regulations allow usage of RAP only for binder and base courses, and its amount is limited. Asphalt mixtures with RAP material have to fulfil requirements stated for typical asphalt mixtures. The research presents low-temperature properties of twelve different asphalt concretes with RAP material, determined using three-point...
-
Non-uniqueness of fracture parameter choice in simulations of concrete cracking at mesoscale level
PublikacjaIn the paper a non-uniqueness of fracture parameter choice in simulations of cracking process in plain concrete specimens at mesoscale level under monotonic static loading is analysed. The Finite Element Method is used, where cracks are defined in a discrete way using interface cohesive elements with nonlinear material law including softening. The concrete mesostructure (such as: cement matrix, air voids, aggregates, and Interfacial...
-
On degradation of glass/polyester laminate immersed in water
PublikacjaMechanical behaviour was compared for glass/ polyester laminates manufactured in the boatbuilding plant using three methods: hand lay-up, vacuum bagging, infusion. Specimens were tested in dry condition and following accelerated water immersion test (70°C- corresponding to the exposure of 30 years at 19°C). In three point bending test 40-50% reduction in laminate strength was observed due to water immersion. The highest degradation...
-
The use of a two-phase Monte Carlo material model to reflect the dispersion of asphalt concrete fracture parameters
PublikacjaThe work covers comprehensive laboratory tests of semi-circular bending (SCB) of asphalt concrete samples. The results of two test series, including four and 32 SCB specimens, indicate a substantial scatter of force–deflection (F-d) histories. The numerical analysis is aimed to reflect the maximum breaking load and fracture energy of the samples, pointing out their random character. The original simulation-based fictitious Monte...
-
Asphalt concrete subjected to long-time loading at low temperatures – Deviations from the time-temperature superposition principle
PublikacjaThe article presents the observed deviations from the time-temperature superposition principle of asphalt concretes, tested in the bending beam creep test at low temperatures for a long time of loading. In almost all tested asphalt concretes, deviations appeared after 500 s of loading at the temperature of -10 C. Some types of bitumen presented deviations at other temperatures – usually the harder the grade of the bitumen, the...
-
Comparative study of numerical modelling and experimental investigation for vessel-docking operations
PublikacjaA comparative study between numerical modelling and experimental investigation is performed to validate the developed numerical method for simulating floating dock operations with a vessel on board. Both model-scale and full-scale experimental tests are performed on floating docks with a vessel on board, and the draughts using draught meters, floating positions and bending of the floating dock are measured. The present numerical...
-
Continuum models for pantographic blocks with second gradient energies which are incomplete
PublikacjaWe postulate a deformation energy for describing the mechanical behavior of so called pantographic blocks, that is bodies constituted by stacking of layers of pantographic sheets. We remark that the pantographic effect is limited in the plane of pantographic sheets and therefore only the second derivatives of transverse displacements along the pantographic fibers appear in the chosen deformation energy. We use this novel energy...
-
Sestaveni Smerne Krivky Modulu Tuhosti Pro Zkoumani Nizkotrplotnich Vlastnosti (Developing of Stiffness Master Curve for Analysis of Low Temperature Properties)
PublikacjaV prispevku je predstaven novy postup pro sestrojeni smernych tuhostnich krivek. Nizkoteplotni vlastnosti asfaltove smesi byly stanoveny za vyuziti zkousky dotvarovani pri tribodovem ohybu. Motivem tohoto vyzkumu je skutecnost, ze metody hodnoceni nizkoteplotniho chovani asfaltovych smesi, nove zavedenych v Polsku, nejsou dostatecne. V zaveru jsou prezentovany smerne krivky tuhosti beznych asfaltovych smesi vyuzivanych v Polsku.
-
A constitutive law for concrete with smooth transition from continuous into discontinuous cracks’ description
PublikacjaPaper presents a constitutive model for concrete that combines a continuous and discontinuous crack’s description to simulate the concrete under tensile dominated loads. In a continuum regime, two different constitutive laws were used. First, a plasticity model with the Rankine failure criterion and an associated flow rule was used. Second, a constitutive law based on isotropic damage mechanics was formulated. Both model alternatives...
-
A method to assess transverse vibration energy of ship propeller shaft for diagnostic purposes
PublikacjaThe article discusses a key problem of ship propulsion system vibration diagnostics, which concerns assessing this part of mechanical energy transmitted from the main engine to the ship propeller which is dissipated due to propeller shaft vibration. A simplified calculation model is proposed which allows the total energy of the generated torsional vibration to be assessed from the shaft deflection amplitude measured at the mind-span...
-
Instrumented End Notched Flexure - Crack propagation and process zonemonitoring. Part I: Modelling and analysis
PublikacjaAnalysis of the three-point bending, End Notched Flexure (ENF), test is presented for exploitation with a new experimental methodology using the backface strain monitoring technique. The model consists oftwo Timoshenko beams joined with a two parameter elastic foundation, to evaluate stress and strain fields in both adherends and the adhesive layer, together with the specimen compliance and energyrelease rate. This model is compared...
-
A material model of asphalt mixtures based on Monte Carlo simulations
PublikacjaThe paper aims to numerically reflect mineral-asphalt mixture structure by a standard FEM software. Laboratory test results are presented due to bending tests of circular notched elements. The result scatter is relatively high. An attempt was made to form a random aggregate distribution in order to obtain various results corresponding to laboratory tests. The material structure calibration, its homogenization and finite element...
-
Mesoscopic simulations of crack propagation in concrete using cohesive elements
PublikacjaThe paper presents results of two-and three-dimensional meso-scale simulations of fracture in notched concrete beams subjected to three-point bending test. Concrete was assumed as a 3-phase material composed of aggregate grains placed in the cement matrix with Interfacial Transitional Zones (ITZs) between then. In 2D simulations macro-voids were also taken into account. The particle distribution was taken from real concrete beams...
-
Analytical approach for membrane action in laterally-restrained reinforced concrete square slabs under uniformly distributed loads
PublikacjaLaterally-restrained reinforced concrete slabs can mobilise compressive membrane action and subsequent tensile membrane action under extreme loading conditions, thereby enhancing the load resistance under uniformly distributed loads. Previous analytical study focuses primarily on tensile membrane action in simply-supported slabs. This paper describes an analytical approach for membrane action in laterally-restrained square slabs....
-
Tensile and flexural moduli for human orbital wall bones – comparative study
PublikacjaThe main aims of the current research were: (1) to analyze in detail the tensile modulus and ultimate tensile strength (UTS) of orbital wall bones separately for the left and right orbit of the same cadaver and (2) to compare the obtained results with a flexural modulus of the left and right orbit reported earlier by A. C. van Leeuwen et al. [14]. A set of 54 specimens of orbital superior and/or medial walls harvested from 16 human...