Filtry
wszystkich: 280
wybranych: 234
Wyniki wyszukiwania dla: SINGLE‐PASS SURFACE GRINDING
-
The Influence of the Depth of Cut in Single-Pass Grinding on the Microstructure and Properties of the C45 Steel Surface Layer
PublikacjaThe paper contains the results of a metallographic examination and nanoindentation test conducted for the medium carbon structural steel with low content of Mn, Si, Cu, Cr, and Ni after its grinding to a depth ranging from 2 μm to 20 μm, at constant cutting speed (peripheral speed) of vs = 25 ms−1 and constant feed rate of vft = 1 m/min. Applied grinding parameters did not cause the surface layer hardening, which could generate...
-
Monitoring of single-side lap grinding with electroplated tools
PublikacjaThe results presented in the paper show that utilising microphones as audible sound sensors is a suitable approach for monitoring a single-side lap grinding process due to the low levels of noise generated by the drives of a machine tool. The results confirm that sound signal analysis is a feasible and relatively simple method to monitor a lap grinding process with the use of an audible sound sensor. Proposed method can be used...
-
Analysis of Roughness, the Material Removal Rate, and the Acoustic Emission Signal Obtained in Flat Grinding Processes
PublikacjaIn this work, the analysis of the acoustic emission (AE) signal in grinding processes is addressed. The proposed analysis method decomposes the acoustic signal into three frequency ranges. The total energy of each range is determined, as well as the highest frequency. Different grinding experiments were carried out, according to a full factorial design of experiments (DOE), in which feed speed, depth of cut, and transversal step...
-
Vertical vibration reduction and audible sound analysis in surface grinding with electroplated tools
PublikacjaOne of the first approaches to the development of a grinding process monitoring system based on audible sound sensors is presented in the paper. Electroplated diamond tools (abrasive D64 and D107) were used in a modified single-disc lapping machine configuration for flat grinding of ceramics (Al2O3). The main aim of the machine modification was to reduce the vertical vibration in order to decrease the tool wear and to increase...
-
Estimation of wear of electroplated tools used for surface grinding
PublikacjaW pracy dokonano ilościowej oceny zużycia narzędzi galwanicznych diamentowych i borazonowych. Wykorzystano analizę jasności obrazów narzędzi oraz badano liczność ziaren ściernych na czynnej powierzchni narzędzia.
-
A Comparative Study of Precision Surface Grinding Using Additively Fabricated Acrylonitrile–Butadiene–Styrene (ABS) Wheels with Continuous and Serrated Working Surfaces
PublikacjaNowadays, high requirements imposed by mechanical components make it necessary to develop modern production methods. Additive technologies have been dynamically developing in recent years, showing many advantages associated with the fabrication of elements with complex ge-ometries and structures. One of the areas where the potential of additive technologies is exploited is the rapid tooling sector, which is based on the rapid production...
-
Representativity of ISO test track surface based on controlled pass-by measurements
PublikacjaWithin the Polish-Norwegian research project ELANORE, a limited Round Robin Test has been performed on four ISO tracks in Northern Europe. The basic objective of the project is to improve the EU directive on labelling of tyres for noise and rolling resistance. This directive is based on the measurement procedures proscribed in the UNECE Reg.117. Measurements on 3 ISO tracks were performed in 2021 and presented at InterNoise 2022....
-
Influence of parameters of deep grinding on nanohardness and surface roughness of C45 steel
PublikacjaPrzedstawiono wyniki badań wpływu głębokości współbieżnego szlifowania powierzchni płaskich na chropowatość i nanotwardość warstwy wierzchniej stali C45 o strukturze ferrytyczno-perlitycznej i średniej wielkości ziarna 20 μm. Dla wszystkich wartości głębokości szlifowania uzyskano znaczny wzrost twardości warstwy wierzchniej przedmiotu obrabianego.
-
Shaping of the workpiece surface in single-disc lapping
PublikacjaPrzedstawiono korelację pomiędzy błędami kształtu docieraka i błędami kształtu przedmiotów obrabianych. Wyniki analityczne zostały sprawdzone doświadczalnie, co pozwoliło zbudować komputerowy model kształtowania powierzchni docieranych. Przedstawiono sposób wyznaczania intensywności kontaktu między przedmiotem docieranym, a docierakiem. Opracowano metodę wyznaczania położenia przedmiotu na docieraku.
-
Shaping of the workpiece surface in single-disc lapping
PublikacjaShape errors of the tool exert a dominant influence on the shape accuracy of the workpiece. The correlation between flatness errors of the lap and flatness errors of the workpieces was checked experimentally and determined analytically. Computer model of the workpiece shaping by lapping was developed. Evaluation method of the workpiece orientation as well as some simulation results for a lap with shape errors of convexity and cincavity...
-
Experimental study on single phase operation of microjet augmented heat exchanger with enhanced heat transfer surface
PublikacjaThe article presents experimental investigations on a prototype heat exchanger. Presented research is focused on combined active and passive enhancement techniques of surface modification and microjet impingement. The results were compared to reference plate heat exchanger without microjet impingement. The Wilson plot method was applied to determine the heat transfer coefficients in the single phase operation. The heat exchanger...
-
Efficiency of hybrid equipment combining operations of surface hardening by high frequency currents and abrasive grinding
Publikacja -
Surface sliding in human abdominal wall numerical models: Comparison of single-surface and multi-surface composites
PublikacjaDetermining mechanical properties of abdominal soft tissues requires a coupled experimental-numerical study, but first an appropriate numerical model needs to be built. Precise modeling of human abdominal wall mechanics is difficult because of its complicated multi-layer composition and large variation between specimens. There are several approaches concerning simplification of numerical models, but it is unclear how far one could...
-
Experimental and theoretical study of surface cooling using a single microjet
PublikacjaPrzedstawiono wyniki badań eksperymentalnych intensyfikacji wymiany ciepła przy pomocy pojedynczych strug wody i powietrza.Uzyskana na podstawie wyników korelacja, opisująca współczynnik przejmowania ciepła, posłużyła do weryfikacji modelu opracowanego wcześniej przez Mikielewicza (2007).
-
Stability analysis of single-walled carbon nanotubes embedded in winkler foundation placed in a thermal environment considering the surface effect using a new refined beam theory
PublikacjaThis article is devoted to investigate the stability of different types of Single Walled Carbon Nanotubes (SWCNTs) such as zigzag, chiral, and armchair types which are rested in Winkler elastic foundations exposing to both the low and high temperature environments. Also, the Surface effects which include surface energy and surface residual stresses, are taken into consideration in this study. It may be noted that the surface energy...
-
Photodegradation of lauric acid at an anatase single crystal surface studied by atomic force microscopy
PublikacjaBadania obejmowały obserwację zmian topografii powierzchni, za pomocą mikroskopii sił atomowych, cienkiej warstwy kwasu laurynowego osadzonego na monokrysztale anatazu. Warstwę kwasu laurynowego o grubości 80-90 nm naświetlano promieniowaniem z zakresu UV-Vis. Zauważono, że kwas laurynowy osadzany metodą wirującego dysku tworzy na powierzchni monokryształów TiO2 struktury domenowe. Stwierdzono, że podczas naświetlania nie ulega...
-
Surface morphology of PrBa2Cu3O7-ë single crystals after the long lasting high temperature reduction. .
PublikacjaZaprezentowano wyniki szczegółowej analizy powierzchni kryształów poddanych długotrwałej redukcji wysokotemperaturowej. Badania za pomocą skaningowej mikroskopii (SEM) wykazały obecność niestabilnych strukturalnie krystalitów powstałych w wyniku rozpadu powierzchni kryształów. Zanikanie zaindukowanego przy pomocy obróbki wysokotemperaturowej nadprzewodnictwa może być spowodowane migracją defektów podsieci Pr-Ba z wnętrza...
-
Highly efficient rutile TiO2 photocatalysts with single Cu(ii) and Fe(iii) surface catalytic sites
Publikacja -
Microgrinding with single-disk lapping kinematics.
PublikacjaGrinding operations are carried out with a variety of tool-workpiece configurations. The selection of a grinding process for a particular application depends on part shape, part size, ease of fixture, requirements concerning the acceptable shape errors. It is evident that lapping is very effective in eliminating the waviness while surface grinding is not. Dual disk machines for the double face grinding with planetary kinematics...
-
INFLUENCE OF SINGLE-STAGE AND DUPLEX SHOT PEENING ON SURFACE ROUGHNESS AND RESIDUAL STRESSES IN Al Mg5 Mn1 Sc0,8 Zr0,4 ALLOY
Publikacja -
Method of Monitoring of the Grinding Process with Lapping Kinematics Using Audible Sound Analysis
PublikacjaUtilising microphones as audible sound sensors for monitoring a single-side grinding process with lapping kinematics is presented in the paper. The audible sound generated during grinding depended on the cutting properties of electroplated tools with D107 diamond grains and different thicknesses of the nickel bond. The tool wear affected the obtained technological effects such as material removal rate and the surface roughness...
-
Wear of electroplated diamond tools in lap-grinding of Al2O3 ceramic materials
PublikacjaCurrent development of modern products, together with ever-increasing demands for their operation and usage, necessitate the search for new processing methods. Abrasive machining is widely used in many industrial areas, especially for processing difficult-to-machine materials such as advanced ceramics. Grinding with lapping kinematics, also called lap-grinding, is still one of the innovative methods of abrasive processing being...
-
Influence of Flat Lapping Kinematics on Machinability of Ceramics
PublikacjaNew tools for flat grinding of ceramics are presented in the paper. Electroplated CBN tools (B64 and B107) were used in a modified single-disc lapping machine configuration. The results from experiments, such as the material removal rate and surface roughness parameters are presented and analyzed. Numerical simulations, based on the model for the shape error and tool wear estimation in machining with flat lapping kinematics, are...
-
The use of Preston equation to determine material removal during lap-grinding with electroplated CBN tools
PublikacjaGrinding executed in a lapping configuration is an alternative finishing process benefiting from both grinding and free-abrasive machining, while minimizing the heat effect impact. Electroplated tools can be effectively used in different abrasive processes, including high-speed grinding, however, the assessment of machining performance over time is a key factor in their correct use to achieve satisfactory technological results....
-
Thermal and technological aspects of double face grinding of C45 carbon steel
PublikacjaIn grinding, the contact zone temperature is a decisive factor influencing the achievable surface quality and the grinding tool wear. In contrast to other grinding processes, only few information regarding double face grinding with planetary kinematics when processing steel is known up to date. Since the successive substitution of in-dustrial double-sided lapping processes by double-sided grinding, it has become necessary to the...
-
The Impact of Material Selection on Durability of Exhaust Valve Faces of a Ship Engine – A Case Study
Publikacjawo alloys were used in order to extend the service life of marine engine exhaust valve head. Layers of cobalt base alloys were made of the powders with with chemical composition as follow: the layer marked L12; C-1,55%; Si-1,21%; Cr-29,7%; W-9%; Ni-2%; Mo<0,01%; Fe-1,7%; Co-54,83% and the layer marked N; C-1,45%; Co-38,9%; Cr-24,13%; Ni-10,43%; W-8,75%; Fe-7,64%; Mo-7,56%; Si-2,59%. Base metal was valve steel after heat treatment....
-
Corrigendum to “An investigation on residual stress and fatigue life assessment of T-shape welded joints” [Eng. Fail. Anal. 141 (2022) 106685]
PublikacjaThis paper aims to quantitatively evaluate the residual stress and fatigue life of T-type welded joints with a multi-pass weld in different direction. The main research objectives of the experimental test were to test the residual stress by changing direction along with multiple wielding passes and determine the fatigue life of the welded joints. The result shows that compressive residual stress increases in the sample gradually...
-
An investigation on residual stress and fatigue life assessment of T-shape welded joints
PublikacjaThis paper aims to quantitatively evaluate the residual stress and fatigue life of T-type welded joints with a multi-pass weld in different direction. The main research objectives of the experimental test were to test the residual stress by changing direction along with multiple wielding passes and determine the fatigue life of the welded joints. The result shows that compressive residual stress increases in the sample gradually...
-
The influence of rubber recyclate morphology on the properties of rubber-asphalt composite
PublikacjaIn the paper wastes, mostly in the form of used tires, were analyzed. One of the methods of waste tires application use them as a modifier of asphalt. However, the properties of rubber-asphalt composites depend on the morphology of waste tiregranulate and kind of tire recycled (car/truck). In this chapter, the influence of grinding methods of waste tire on the prop¬erties of rubber-asphalt composites were studied. SEM analysis...
-
The best porous asphalt pavement in Sweden so far
PublikacjaIn 2010 a double-layer porous asphalt concrete (DPAC) pavement was constructed in various versions on the E4 motorway through the Swedish city Huskvarna. As a result of a court decision the Swedish Transport Administration had to reduce noise emission by applying a low noise road surface that would reduce A-weighted noise levels by 5 dB, as an average. Earlier experience in Sweden indicated that it was possible to obtain a high...
-
Analysis of pavement structure sensitivity to passage of oversized heavy duty vehicle in terms of bearing capacity
PublikacjaOversized heavy duty vehicles occur in traffic very rarely but they reach extremely high weights, even up to 800 tonne. The detrimental impact of these vehicles on pavement structure is much higher than in case of commercial vehicles that comprise typical traffic, thus it is necessary to assess the sensitivity of pavement structure to passage of oversized vehicles. The paper presents results of sample calculations of load equivalency factor...
-
Support Vector Machine Applied to Road Traffic Event Classification
PublikacjaThe aim of this paper is to present results of road traffic event signal recognition. First, several types of systems for road traffic monitoring, including Intelligent Transport System (ITS) are shortly described. Then, assumptions of creating a database of vehicle signals recorded in different weather and road conditions are outlined. Registered signals were edited as single vehicle pass by. Using the Matlab-based application...
-
Influence and development of new kinematic systems in flat surface lapping
PublikacjaThe face grinding and lapping technology is widely used in the field of the precise and ultraprecise manufacturing. It has become an indispensable technology in the manufacture of many parts. An absence of material restrictions allows machining both metal and non-metallic materials, including technical ceramics [1]. Nowadays there are mainly two kinematic systems in lapping machines [2]. The machining plane-parallel surfaces is...
-
HOW EFFICIENT IS NOISE LABELING OF TIRES?
PublikacjaSince 2012 all new tires in Europe must be labeled. The label contains general information about tire performance concerning rolling resistance (that corresponds to fuel economy), noise emission and wet grip (only for passenger car tires). Measurements of noise performance of tires must be performed according to the Annex 3 of the Regulation No 117 of the Economic Commission for Europe of the United Nations. The regulation specifies...
-
Multiple output differential OTA with linearizing bulk-driven active-error feedback loop for continuous-time filter applications
PublikacjaA CMOS circuit realization of a highly linear multiple-output differential operational transconductance amplifier (OTA) has been proposed. The presented approach exploits a differential pair as an input stage with both the gate and the bulk terminals as signal ports. For the proposed OTA, improved linearity is obtained by means of the active-error feedback loop operating at the bulk terminals of the input stage. SPICE simulations...
-
The effect of tyre rubber grinding method on the rubber-asphalt binder properties
PublikacjaRubber products, especially those used in the automotive industry, are responsible for a significant amount of waste, mainly in the form of worn tyres. One way to recycle tyres is to use them as an asphalt binder modifier. The properties of rubber-asphalt binders vary greatly depending on the morphology of the ground tyre rubber (GTR) grains and the type of tyre to be recycled (car/truck). The paper presents the results of research...
-
Testing the Effect of Bathymetric Data Reduction on the Shape of the Digital Bottom Model
PublikacjaDepth data and the digital bottom model created from it are very important in the inland and coastal water zones studies and research. The paper undertakes the subject of bathymetric data processing using reduction methods and examines the impact of data reduction according to the resulting representations of the bottom surface in the form of numerical bottom models. Data reduction is an approach that is meant to reduce the size...
-
Advances and Trends in Non-Conventional, Abrasive and Precision Machining 2021
PublikacjaIn the modern, rapidly evolving industrial landscape, the quest for machining and production processes consistently delivering superior quality and precision is more pronounced than ever. This necessity and imperative are driven by the increasing complexity in the design and manufacturing of mechanical components, an evolution in lockstep with the swift advancements in material science. The real challenge of this evolution lies...
-
Generative Process Planning with Reasoning based on Geometrical Product Specification
PublikacjaThe focus of this paper is on computer aided process planning for parts manufacture in systems of definite process capabilities, involving the use of multi-axis machining centers for parts shaping and grinding machines for finishing. It presents in particular a decision making scheme for setup determination as a part of generative process planning. The planning procedurę consists of two stages. The first stage is associated with...
-
The Influence of Workpiece Hardness on Plate Temperature during One Side Lapping
PublikacjaLapping leads to a surface with low roughness and high precision. Because of required parts accuracy tool flatness is the key to the successful machining. To avoid its excessive thermal expansion, plate temperature research was taken. The goal was to determine the correlation between the basic lapping conditions and wheel temperature. In work Bulsara et al. authors developed model to estimate the maximum and average temperature...
-
Surface diffusion and cluster formation of gold on the silicon (111)
PublikacjaPurpose: Investigation of the gold atoms behaviour on the surface of silicon by molecular dynamics simulation method. The studies were performed for the case of one, two and four atoms, as well as incomplete and complete filling of gold atoms on the silicon surface. Design/methodology/approach: Investigations were performed by the method of molecular dynamics simulation using the Large-scale Atomic/Molecular Massively Parallel...
-
Monitoring wizyjny w systemach zabezpieczenia transportu wodnego. Koncepcja implementacyjna
PublikacjaW artykule autorzy przedstawiają koncepcję zastosowania własnych badań nad pomiarem prędkości przepływu cieczy do zastosowań praktycznych w pomiarach przepływu wody w kanałach otwartych i rzekach. Jako narzędzie pomiarowe wykorzystują zestaw aparatów synchronicznych, które rejestrują indykatory przepływu znajdujące się na powierzchni analizowanej cieczy. Aparat matematyczny przedstawiony w rozwiązaniu sprowadza się do stosowania...
-
Comparison of heat transfer characteristics in surface cooling with boiling microjets of water, ethanol and HFE7100
PublikacjaThe basis of microjet technology is to produce jets which impinge the surface at the stagnation point with a very high kinetic energy. Main objective of this paper was to investigate the physical phenomena occurring on solid surfaces upon impingement of the single microjet in case of three fluids, namely water, ethanol and HFE7100. Intense heat transfer in the impact zone of microjet has been examined and described with precise...
-
A new anisotropic bending model for nonlinear shells: Comparison with existing models and isogeometric finite element implementation
PublikacjaA new nonlinear hyperelastic bending model for shells formulated directly in surface form is presented, and compared to four existing prominent bending models. Through an essential set of elementary nonlinear bending test cases, the membrane and bending stresses of each model are examined analytically. Only the proposed bending model passes all the test cases, while the other bending models either fail or only pass the test cases for...
-
Measurement of the Temporal and Spatial Temperature Distribution on the Surface of PVCP Tissue Phantom Illuminated by Laser Dataset
PublikacjaThe dataset entitled Measurement of the temporal and spatial temperature distribution on the surface of PVCP tissue phantom illuminated by laser was obtained with a laboratory set-up for characterisation of the thermal properties of optical tissue phantoms during laser irradiation. The dataset contains a single image file representing the spatial temperature distribution on the surface of a PVCP tissue phantom. This thermal image...
-
Experiment with small objects floating under water in the harbor security aspect.
PublikacjaObservation of the underwater area is the element of general trend which primary purpose is to protect and enhance the safety of the selected region. The aim of the paper is to present the acoustic characteristics of typical objects floating on the surface or under the water, which constitute some knowledge on how to detect these objects. Create a catalog of acoustic signatures and acoustic images of objects mostly floating under...
-
Research on the wear evenness of the tool in flat lapping
PublikacjaIn this paper, the dimensionless distribution of the material removal stock and the trajectories of abrasive grains cutting in single-sided lapping process are presented. They were numerically simulated based on the tribological model and kinematics equations. It can be observed that the trajectories geometry of single abrasive as well the velocities have a great influence on the final geometrical deviation. During machining, the...
-
Heat transfer and pressure drop characteristics of the silicone-based plate heat exchanger
PublikacjaThe paper presents an experimental investigation of a silicone based heat exchanger, with passive heat transfer intensification by means of surface enhancement. The main objective of this paper was to experimentally investigate the performance of a heat exchanger module with the enhanced surface. Heat transfer in the test section has been examined and described with precise measurements of thermal and flow conditions. Reported...
-
Model of heat transfer in the stagnation point of rapidly evaporating microjet
PublikacjaThe paper presents investigation in the single water microjet surface cooling producing evaporating film. Reported tests were conducted under steady state conditions. It was proved that the phenomenon is similar to that of pool boiling. Results of experiments were compared with predictions by the model showing a good consistency.
-
Correlation between Fractal Dimension and Areal Surface Parameters for Fracture Analysis after Bending-Torsion Fatigue
PublikacjaThis paper investigates the fracture surface topography of two steel and aluminum alloys subject to bending-torsion fatigue loadings, as well as their susceptibility to fatigue performance and failure mechanisms. Using fracture surface topography data analysis, elements with different geometries were elaborated. A correlation between the fractal dimension, other selected parameters of surface topography such as areal Sx, and...