Wyniki wyszukiwania dla: LAST STAGE OF LOW-PRESSURE
-
Development of a spray-ejector condenser for the use in a negative CO2 emission gas power plant
PublikacjaOne promising solution for developing low-emission power technologies is using gaseous fuel combustion in pure oxygen when the exhaust gas mixture is composed of H2O and CO2, and where CO2 is separated after steam condensation. The paper presents the results of computational analyses providing to the Spray-Ejector Condenser (SEC) development, which is one of the crucial components of the negative CO2 gas power plant (nCO2PP) cycle...
-
Exergy Losses in the Szewalski Binary Vapor Cycle
PublikacjaIn this publication, we present an energy and exergy analysis of the Szewalski binary vapor cycle based on a model of a supercritical steam power plant. We used energy analysis to conduct a preliminary optimization of the cycle. Exergy loss analysis was employed to perform a comparison of heat-transfer processes, which are essential for hierarchical cycles. The Szewalski binary vapor cycle consists of a steam cycle bottomed with...
-
Looking for a minimum exergy destruction in hierarchical cycle
PublikacjaThe paper presents results of energy analysis, complemented with an exergy balance, of hierarchical thermodynamic cycle. Proposed cycle is a binary vapour cycle based on a model of real supercritical steam power plant. Energy analysis is used to preliminary optimization of the cycle and the exergy losses analysis is proposed to perform optimization of heat transfer processes, which are essential for hierarchical cycles. Proposed...
-
Optical flow method for measuring deformation of soil specimen subjected to torsional shearing
PublikacjaIn this study optical flow method was used for soil small deformation measurement in laboratory tests. The main objective was to observe how the deformation distributes along the whole height of cylindrical soil specimen subjected to torsional shearing (TS test). The experiments were conducted on dry non-cohesive soil specimens under two values of isotropic pressure. Specimens were loaded with low-amplitude cyclic torque to analyze...
-
Rapid and Reliable Re-Design of Miniaturized Microwave Passives by Means of Concurrent Parameter Scaling and Intermittent Local Tuning
PublikacjaRe-design of microwave passive components for the assumed operating frequencies or substrate parameters is an important yet a tedious process. It requires simultaneous tuning of relevant circuit variables, often over broad ranges thereof, to ensure satisfactory performance of the system. If the operating conditions at the available design are distant from the intended ones, local optimization is typically insufficient, whereas...
-
WYBRANE WŁAŚCIWOŚCI FIZYCZNO-CHEMICZNE MIKROSFER I MOŻLIWOŚĆ ICH WYKORZYSTANIA W KOMPOZYTACH CEMENTOWYCH : The selected physico-chemical properties of microspheres and possibility of their use in cement composites
PublikacjaMicrospheres are formed during the mineral transformation stage in coal combustion. Their content in fly ashes from the combustion of different types of coals varies over a rather wide range from 0.01 to 4.8 wt.%. The microspheres have three main elements, silicon, aluminum and iron, the oxides of which account for about 89.0 wt.% of the material. Mineralogical analysis using XRD shows that microspheres mainly contain mullite and...
-
Predicting cutting power for band sawing process of pine and beech wood dried with the use of four different methods
PublikacjaWood drying is an important stage in the woodworking process. After drying, wood is subject to a re-sawing process, for which a high quality surface, low material loss, and high efficiency are often required. In this paper, forecasted values were presented of cutting power for the re-sawing process of pine and beech wood that were dried with four different methods. Forecasting of cutting power for an industrial band saw machine...
-
Low-volume label-free SARS-CoV-2 detection with the microcavity-based optical fiber sensor
PublikacjaAccurate and fast detection of viruses is crucial for controlling outbreaks of many diseases; therefore, to date, numerous sensing systems for their detection have been studied. On top of the performance of these sensing systems, the availability of biorecognition elements specific to especially the new etiological agents is an additional fundamental challenge. Therefore, besides high sensitivity and selectivity, such advantages...
-
Large hydrodynamic thrust bearing: Comparison of the calculations and measurements
PublikacjaHydrodynamic thrust bearings, used to carry axial loads in heavily loaded shafts of water power plants hydro turbines, can reach outer diameters even exceeding 5 m. In such large objects scale effect could be observed. According to this, allowable bearing specific load assuring safe operation of the bearings has to be decreased, which increases thrust bearing dimensions. This effect is caused by excessive thermal deflections of...
-
Fouling mechanisms in anoxic-aerobic sequencing batch membrane bioreactor based on adapted Hermia models and main foulant characteristics
PublikacjaVarious derivatives of Hermia models (complete pore blocking, intermediate pore blocking, cake layer formation, and standard pore blocking) and different assessments of foulant characteristics have long been used to determine the membrane fouling mechanisms. Accordingly, this study aims to adapt Hermia models and their combination according to the operating conditions of an anoxic-aerobic sequencing batch membrane bioreactor (A/O-SBMBR)....
-
Diagnostyka analogowych filtrów wielosekcyjnych oparta na klasyfikato-rach neuronowych z dwucentrowymi funkcjami bazowymi
PublikacjaPrzedmiotem artykułu jest zastosowanie klasyfikatora z dwucentrowymi funkcjami bazowymi do lokalizacji uszkodzeń w wielosekcyjnych torach analogowych elektronicznych systemów wbudowanych sterowanych mikrokontrolerem. Przedstawiono szczegóły procedury pomiarowej oraz metody detekcji i lokalizacji uszkodzeń toru analogowego z wykorzysta-niem klasyfikatora DB zaimplementowanego w postaci algorytmicznej w kodzie programu mikrokontrolera....
-
Detection of the Incoming Sound Direction Employing MEMS Microphones and the DSP
PublikacjaA 3D acoustic vector sensor based on MEMS microphones and its application to road traffic monitoring is presented in the paper. The sensor is constructed from three pairs of digital MEMS microphones, mounted on the orthogonal axes. Signals obtained from the microphones are used to compute sound intensity vectors in each direction. With this data, it is possible to compute the horizontal and vertical angle of an incoming sound....
-
Green products from herbal medicine wastes by subcritical water treatment
PublikacjaHerbal medicine wastes (HMWs) are byproducts of medicine factories, which are mainly landfilled for their environmental problems. Only bearing in mind the contamination and concerns caused by the COVID-19 pandemic and environmental emissions, the worth of herbal medicine wastes management and conversion to green products can be understood. In this work, subcritical water treatment was carried out batch-wise in a stainless tube...
-
Human subarachnoid space width oscillations in the resting state
PublikacjaAbnormal cerebrospinal fluid (CSF) pulsatility has been implicated in patients suffering from various diseases, including multiple sclerosis and hypertension. CSF pulsatility results in subarachnoid space (SAS) width changes, which can be measured with near-infrared transillumination backscattering sounding (NIR-T/BSS). The aim of this study was to combine NIR-T/BSS and wavelet analysis methods to characterise the dynamics of the...
-
Structure and paramagnetism in weakly correlated Y8Co5
PublikacjaWe report the basic physical properties of monoclinic Y8Co5 determined by means of magnetic susceptibility, electrical resistivity, and specific heat measurements. The crystal structure of Y8Co5 is monoclinic (P21/c) with lattice parameters a = 7.0582(6) Å, b = 7.2894(6) Å, c = 24.2234(19) Å, and β = 102.112(6)° as refined by using synchrotron powder x-ray diffraction data. The compound shows temperature independent paramagnetism...
-
Recent Progress on Hydrogen Storage and Production Using Chemical Hydrogen Carriers
PublikacjaDepleting fossil fuel resources and anthropogenic climate changes are the reasons for the intensive development of new, sustainable technologies based on renewable energy sources. One of the most promising strategies is the utilization of hydrogen as an energy vector. However, the limiting issue for large-scale commercialization of hydrogen technologies is a safe, efficient, and economical method of gas storage. In industrial practice,...
-
Numerical analysis of CO2-water separation in a horizontal double T-junction
PublikacjaCarbon dioxide is considered one of the main factors leading to global warming. Considering the significant impacts of CO2 on climate change, various technologies have been developed in recent decades to control carbon emission, such as for example CO2 capture and storage. The developed cycle of a negative CO2 emission power plant includes some devices, out of which, separator plays an indispensable role. To this end, T-junction...
-
Identification of synergistic and antagonistic actions of environmental pollutants: Bisphenols A, S and F in the presence of DEP, DBP, BADGE and BADGE·2HCl in three component mixtures
PublikacjaEcosystems are facing increased pressure due to the emission of many classes of emerging contaminants. However, very little is known about the interactions of these pollutants, such as bisphenols (BPs), plasticizers or pharmaceuticals. By employing bioluminescent bacteria (Microtox assay), we were able to define interactions between selected emerging pollutants (namely BPA, BPS, BPF, BADGE, BADGE·2HCl, DEP, DBP) in ternary mixtures, at...
-
Local-Global Space Mapping for Rapid EM-Driven Design of Compact RF Structures
PublikacjaIn this work, we introduce a robust and efficient technique for rapid design of compact RF circuits. Our approach exploits two-level space mapping (SM) correction of an equivalent circuit model of the structure under design. The first SM layer (local correction) is utilized to ensure good matching between the equivalent circuit and the electromagnetic model at the component level. On the other hand, the global correction allows...
-
Nanoparticles preparation using microemulsion systems
PublikacjaMetallic nanoparticles become of current interests because they exhibit unique properties compared with those of metal atoms or bulk metal due to the quantum size effect and their large surface area, which make them attractive for applications in optics, electronics, catalysis biology and medicine. TiO2 has been used for environmental remediation purposes such as in the purification of water and air and also solar-to chemical energy...
-
Characterization and Technical Application of Fine Photocatalytical Particles - A Study of the Immobilization of Photocatalysts
PublikacjaThe main aim of this dissertation was the transfer of photocatalytical laboratory scale experiments to semi-technical scale. Preliminary experiments of the purification of organic chlorine-loaded waters and the immobilization of photocatalysts were performed, which yielded the research back to the roots of synthesis. The first applied research was carried out on treatment of recreational water. Several light sources, particularly...
-
B-GALACTOSIDASE ARTHROBACTER SP. 32cB - OBTAINING THE GENE SEQUENCE, CONSTRUCTION OF THE EXPRESSION SYSTEM, BIOSYNTHESIS AND BIOCHEMICAL CHARACTERIZATION OF THE ENZYME
PublikacjaINTRODUCTION: β-Galactosidase is an enzyme which catalyzes the hydrolysis of O glycosidic bond in β-galactosides. Another activity of β galactosidase is a transglycosylation activity. The main industrial use of this protein is the hydrolysis of lactose in milk in a cooling conditions. Synthesis of galactooligosaccharides, which are mostly used as a prebiotics added to some foods or available as dietary supplements, is only one...
-
Effect of Coating Material Properties on Tilting-pad Thrust Bearing Performance
PublikacjaPolymer lined tilting-pad bearings demonstrate many advantages over traditional bearing systems. Bearings with a polymer layer in comparison with a babbitted layer show, for example: lower value of friction coefficient (important during start/stops), higher fatigue strength of the coating, better distribution of the load on individual pads due to lower elasticity of the polymers, wider range of operational temperatures or the ability...
-
Highly Conserved Homotrimer Cavity Formed by the SARS-CoV-2 Spike Glycoprotein: A Novel Binding Site
PublikacjaAn important stage in severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) life cycle is the binding of the spike (S) protein to the angiotensin converting enzyme-2 (ACE2) host cell receptor. Therefore, to explore conserved features in spike protein dynamics and to identify potentially novel regions for drugging, we measured spike protein variability derived from 791 viral genomes and studied its properties by molecular...
-
Application of Thermo-chemical Technologies for Conversion of Associated Gas in Diesel-Gas Turbine Installations for Oil and Gas Floating Units
PublikacjaThe paper considers the issue of thermo-chemical recovery of engine’s waste heat and its further use for steam conversion of the associated gas for oil and gas floating units. The characteristics of the associated gas are presented, and problems of its application in dual-fuel medium-speed internal combustion engines are discussed. Various variants of combined diesel-gas turbine power plant with thermo-chemical heat recovery are...
-
Utilisation of waste heat from the power plant by use of the ORC aided with bleed steam and extra source of heat
PublikacjaUtilization of waste heat recovered from the exhaust gases of the power generation unit by means of ORC (organic Rankine cycles) installation is considered. The waste heat is available in the form of a stream of hot water having temperature of 90 stC in the amount of 200 MWt. To increase evaporation temperaturę of ORC working fluid the heat of steam from the extraction points from the low-pressure part of steam turbine is used....
-
Correlations between the wear of car brake friction materials and airborne wear particle emissions
PublikacjaAirborne wear particles emitted from transport vehicle brakes are one of the main sources of toxic metals in inhalable particulate matter. Prediction of wear particle emissions may become more accurate if the relationship between the wear and particle emission characteristics is known. An experimental study was performed to investigate proportional correlations between the mass wear, 0.01–0.42 μm particle emission measured by a NanoScan...
-
Assessment and design of greener deep eutectic solvents – A multicriteria decision analysis
PublikacjaDeep eutectic solvents (DES) are often considered as green solvents because of their properties, such as negligible vapor pressure, biodegradability, low toxicity or natural origin of their components. Due to the fact that DES are cheaper than ionic liquids, they have gained many applications in a short period of time. However, claims about their greenness sometimes seem to be exaggerated. Especially, bearing in mind lots of data...
-
Is the microfiltration process suitable as a method of removing suspended solids from rainwater?
PublikacjaDue to climate change and anthropogenic pressure, freshwater availability is declining in areas where it has not been noticeable so far. As a result, the demands for alternative sources of safe drinking water and effective methods of purification are growing. A solution worth considering is the treatment of rainwater by microfiltration. This study presents the results of selected analyses of rainwater runoff, collected from the...
-
Mild poikilocapnic hypoxia increases very low frequency haemoglobin oxygenation oscillations in prefrontal cortex
PublikacjaBackground: The aim of the study was to investigate the effect of mild cerebral hypoxia on haemoglobin oxygenation(HbO2), cerebrospinal fluid dynamics and cardiovascular physiology. To achieve this goal, four signals were recorded simultaneously: blood pressure, heart rate / electrocardiogram, HbO2 from right hemisphere and changes of subarachnoid space (SAS) width from left hemisphere. Signals were registered from 30 healthy,...
-
Structured deformation of granular material in the state of active earth pressure
PublikacjaThe paper focuses on the ability of granular materials to undergo structured deformation by analysing the data from the retaining wall model tests and discrete element simulations. The structured deformation means the movement of a granular material which produces a stable, regular pattern of multiple shear bands. The paper's primary purpose is to study this kind of deformation for the selected data representing the state of active...
-
Tuning of food wastes bioavailability as feedstock for bio-conversion processes by acoustic cavitation and SPC, SPS, or H2O2 as external oxidants
PublikacjaThe growing amount of food wastes makes them a suitable source for the generation of bioproducts through anaerobic digestion. Appropriate hydrolysis of the feedstock can enhance the efficiency of production of desired products. In this work, acoustic cavitation (AC) was employed as a pretreatment method to enhance hydrolysis stage by the modification of model (potato-based) food waste for increase in soluble chemical oxygen demand...
-
Analysis of pesticide residue in fruits and vegetables using analytical analytical protocol based on application of QuEChERS technique and GC-ECD system
PublikacjaQuEChERS sample preparation method was used for the determination of 10 pesticides and their metabolites in fruits (apple, grape) and vegetables (tomato, paprika), coupled to gas chromatography with electron capture detector (GC-ECD). The experimental parameters including amount of the sample, types of solvents, extraction time and types of sorbent at the purification stage were optimized. The GC-ECD method was validated in terms...
-
Two-Stage Variable-Fidelity Modeling of Antennas with Domain Confinement
PublikacjaSurrogate modeling has become the method of choice in solving an increasing number of antenna design tasks, especially those involving expensive full-wave electromagnetic (EM) simulations. Notwithstanding, the curse of dimensionality considerably affects conventional metamodeling methods, and their capability to efficiently handle nonlinear antenna characteristics over broad ranges of the system parameters is limited. Performance-driven...
-
Context of Digitalized Employment for Older Adults with Autism Spectrum Disorder in the New Normal
PublikacjaEmployers are actively considering how to normalize remote work technology across different industries. The residual risk of coronavirus disease-19 (COVID-19) will necessarily lower the bar for allowing some workers to stay remote on a more permanent basis. This is based on the realization that many essential jobs can be teleworked while retaining or enhancing productivity. The decisions employers make regarding future work arrangements...
-
Enhancing seismic performance of buckling-restrained brace frames equipped with innovative bracing systems
PublikacjaNowadays, to improve the performance of conventional bracing systems, in which, buckling in the pressure loads is the main disadvantage, the buckling-restrained brace (BRB) is introduced as a solution. In this study, the performance of the BRB system was improved with innovative lateral-resisting systems of double-stage yield buckling-restrained brace (DYB), and a combination of DYB improved with shape memory alloy (SMA) materials...
-
The non-invasive evaluation of heart function in patients with an acute myocardial infarction: The role of impedance cardiography
PublikacjaBackground: The purpose of this study was to analyze hemodynamic changes in patients treated with percutaneous coronary intervention (PCI) at an early stage of acute myocardial infarction (AMI) and at one-month follow-up. Methods: Patients with AMI (n = 27) who underwent PCI were analyzed using impedance cardiography (ICG). ICG data were collected continuously (beat by beat) during the whole PCI procedure and thereafter at every...
-
Using Decisional DNA to Enhance Industrial and Manufacturing Design: Conceptual Approach
PublikacjaDuring recent years, manufacturing organizations are facing market changes such as the need for short product life cycles, technological advancement, intense pressure from competitors and the continuous customers’ expectation for high quality products at lower costs. In this scenario, knowledge and its associated engineering/management of every stage involved in the industrial design has become increasingly important for manufacturing...
-
Computer-Aided Detection of Hypertensive Retinopathy Using Depth-Wise Separable CNN
PublikacjaHypertensive retinopathy (HR) is a retinal disorder, linked to high blood pressure. The incidence of HR-eye illness is directly related to the severity and duration of hypertension. It is critical to identify and analyze HR at an early stage to avoid blindness. There are presently only a few computer-aided systems (CADx) designed to recognize HR. Instead, those systems concentrated on collecting features from many retinopathy-related...
-
Rubber wastes recycling for developing advanced polymer composites: A warm handshake with sustainability
PublikacjaRecycling and management of rubber wastes experiences an early-stage maturity in the quest for sustainable and circular materials. Up to now, solutions proposed for sustainable development of rubber wastes are limited, so that properties and performance features of recycled products are inadequate for practical applications. Herein, an experimental protocol is introduced for manufacturing semi-sustainable polymer composites based...
-
Dzielnica Reprezentacyjna Gdyni i jej powojenne oraz współczesne interpretacje
PublikacjaThe concept of the Premiere District in Gdynia was first conceived in the 1920s and from that time on it constantly accompanied the history of the city. It derivated from the idea of creating a symbol of Poland's regaining independence after the first World War and the successful creation of the new port and city on the Baltic coast. As the result of that development, Gdynia was named the maritime capital of Poland and was treated...
-
An asymmetrical λ-foot of condensing steam flow in the IMP PAN nozzle
PublikacjaIn the present paper we have focused on the precise prediction of the spontaneous condensation phenomena in wet steam flow. Novelty of our approach lies on modelling both the moment of initiation of a phase transition, as well as the moment of its reverse progress - called here re-vaporization of the condensate phase. The practical issue is to elaborate of a model of spontaneous condensation/vaporization of water steam flow...
-
Performance analyses of helical coil heat exchangers. The effect of external coil surface modification on heat exchanger effectiveness
PublikacjaThe shell and coil heat exchangers are commonly used in heating, ventilation, nuclear industry, process plant, heat recovery and air conditioning systems. This type of recuperators benefits from simple construction, the low value of pressure drops and high heat transfer. In helical coil,centrifugal force is acting on the moving fluid due to the curvature of thetube results in the development. It has been long recognized that the...
-
Review of the determination of modern used pesticides in water samples
PublikacjaThe increasingly widespread application of pesticides causes that larger amounts of them are entering the environment. Their presence in sources of drinking water, essential to life, is a particular danger. For these reasons it is important to monitor and analyse pesticide residues in the environment. The analysis of environmental samples for the presence of pesticides is very difficult. Firstly, the processes involved in sample...
-
Experimental ORC micro-power plant for CHP application Part B: Radial and Multi-stage axial turbines
PublikacjaThe co-generative micro-power plant with the HFE7100 applied as a working medium was designed and built for experimental investigations. Special attention is paid to a micro-turbine which was built and tested in two variants: a radial turbine and an axial turbine. A concept of a radial turbine with 2 centripetal and 2 centrifugal stages is shown. This prototype was equipped with an aerostatic gas bearing and, alternatively, with...
-
Entrained Flow Plasma Gasification of Sewage Sludge–Proof-of-Concept and Fate of Inorganics
PublikacjaSewage sludge is a residue of wastewater processing that is biologically active and consists of water, organic matter, including dead and living pathogens, polycyclic aromatic hydrocarbons, and heavy metals, as well as organic and inorganic pollutants. Landfilling is on the decline, giving way to more environmentally friendly utilisation routes. This paper presents the results of a two-stage gasification–vitrification system, using...
-
A Surrogate-Assisted Measurement Correction Method for Accurate and Low-Cost Monitoring of Particulate Matter Pollutants
PublikacjaAir pollution involves multiple health and economic challenges. Its accurate and low-cost monitoring is important for developing services dedicated to reduce the exposure of living beings to the pollution. Particulate matter (PM) measurement sensors belong to the key components that support operation of these systems. In this work, a modular, mobile Internet of Things sensor for PM measurements has been proposed. Due to a limited...
-
Low noise poroelastic road pavements based on modified asphalt binder
PublikacjaTire/road noise is one of the most important environmental problems related to road traffic. As the most effective way to fight noise is reduction of sound emission from the source, a lot of work is being done to improve tire and road surfaces construction. This paper describes the first “road” results obtained within the SEPOR project, which is focused on developing a low noise poroelastic road surface based on bituminous binder....
-
Globalized parametric optimization of microwave components by means of response features and inverse metamodels
PublikacjaSimulation-based optimization of geometry parameters is an inherent and important stage of microwave design process. To ensure reliability, the optimization process is normally carried out using full-wave electromagnetic (EM) simulation tools, which entails significant computational overhead. This becomes a serious bottleneck especially if global search is required (e.g., design of miniaturized structures, dimension scaling over...
-
Analityka surfaktantów w próbkach środowiskowych
PublikacjaSurfaktanty stanowią grupę związków charakteryzujących się specyficznymi właściwościami fizykochemicznymi (m.in. amfifilowa budowa, zdolność rozpuszczania się w cieczach o różnej polarności, zdolność do tworzenia micelli) i z tego względu są one wykorzystywane w wielu sferach działalności człowieka. Związki powierzchniowo-czynne ulegają różnorodnym przemianom fizykochemicznym, co umożliwia ich migrację między różnymi elementami...