Filtry
wszystkich: 1174
-
Katalog
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: HIGH-FREQUENCY DESIGN, ELECTROMAGNETIC SIMULATION, SURROGATE MODELING, PERFORMANCE-DRIVEN MODELING
-
Comprehensive dimension scaling of multi-band antennas for operating frequencies and substrate parameters
PublikacjaIn this paper, low-cost and comprehensive redesign of multi-band antennas with respect to the operating frequencies and material parameters of the substrate is presented. Our approach exploits an inverse surrogate model identified based on a set of reference designs optimized at the level of coarse-discretization EM simulations of the antenna at hand. An iterative correction procedure is also implemented to account for the initial...
-
Spectral Finite Element Method in Condition Monitoring and Damage Detection
PublikacjaIt is well known that the dynamic behaviour of engineering structures may carry very important and crucial information that can be further used for the assessment of their condition as well as detection of any damage induced. The current interest in monitoring techniques based on the propagation of guided elastic waves requires that numerical techniques used for modelling the phenomena associated must shift into the realm of high...
-
Failure analysis of a high-speed induction machine driven by a SiC-inverter and operating on a common shaft with a high-speed generator
PublikacjaDue to ongoing research work, a prototype test rig for testing high-speed motors/generators has been developed. Its design is quite unique as the two high- speed machines share a single shaft with no support bearings between them. A very high maximum operating speed, up to 80,000 rpm, was required. Because of the need to minimise vibration during operation at very high rotational speeds, rolling bearings were used. To eliminate...
-
A Microwave Sensor with Operating Band Selection to Detect Rotation and Proximity in the Rapid Prototyping Industry
PublikacjaThis paper presents a novel sensor for detecting and measuring angular rotation and proximity, intended for rapid prototyping machines. The sensor is based on a complementary split-ring resonator (CSRR) driven by a conductor-backed coplanar waveguide. The sensor has a planar topology, which makes it simple and cost-effective to produce and accurate in measuring both physical quantities. The sensor has two components, a rotor, and...
-
Shielded HMSIW-based frequency-tunable self-quadruplexing antenna using different solid/liquid dielectrics
PublikacjaThis article proposes a frequency-tunable self-quadruplexing antenna based on a shielded half-mode substrate integrated waveguide (S-HMSIW). In order to reduce the size of the HMSIW cavity resonator and to obtain quad-band characteristics, a modied E-shaped slot is engraved on the top of the metal. The experimental validation is carried out after analyzing the data using a circuit model. Flexibility of each resonant frequency is...
-
Long Distance Geographically Distributed InfiniBand Based Computing
PublikacjaCollaboration between multiple computing centres, referred as federated computing is becom- ing important pillar of High Performance Computing (HPC) and will be one of its key components in the future. To test technical possibilities of future collaboration using 100 Gb optic fiber link (Connection was 900 km in length with 9 ms RTT time) we prepared two scenarios of operation. In the first one, Interdisciplinary Centre for Mathematical...
-
Heat transfer and pressure drop characteristics of the silicone-based plate heat exchanger
PublikacjaThe paper presents an experimental investigation of a silicone based heat exchanger, with passive heat transfer intensification by means of surface enhancement. The main objective of this paper was to experimentally investigate the performance of a heat exchanger module with the enhanced surface. Heat transfer in the test section has been examined and described with precise measurements of thermal and flow conditions. Reported...
-
A Wideband Corrugated Ridged Horn Antenna with Enhanced Gain and Stable Phase Center for X- and Ku-Band Applications
PublikacjaIn this letter, a structure and design procedure of a novel double-flared conical horn antenna with an improved gain and a stable phase center is presented. The antenna incorporates a hybrid ridged and corrugated structure. A double-ridged section is responsible for ensuring a wideband operation, whereas the corrugated section supports the hybrid mode. The antenna impedance bandwidth (VSWR < 2) is 6 GHz to 20 GHz. Excellent performance...
-
A dual-control strategy based on electrode material and electrolyte optimization to construct an asymmetric supercapacitor with high energy density
PublikacjaMetal-organic frames (MOFs) are regarded as excellent candidates for supercapacitors that have attracted much attention because of their diversity, adjustability and porosity. However, both poor structural stability in aqueous alkaline electrolytes and the low electrical conductivity of MOF materials constrain their practical implementation in supercapacitors. In this study, bimetallic CoNi-MOF were synthesized to enhance the electrical...
-
Activation of peroxymonosulfate using carbon black nano-spheres/calcium alginate hydrogel matrix for degradation of acetaminophen: Fe3O4 co-immobilization and microbial community response
PublikacjaHerein, we focused on the degradation of acetaminophen (ACT) drug in liquid phase by peroxymonosulfate (PMS) activated by carbon black nano-spheres (CBNS). The nanostructured activator was immobilized into calcium alginate hydrogel matrix (CAHM) to avoid the washout of the fine nanostructures. The Langmuir modeling showed an insignificant contribution to the adsorption process in the removal of ACT. The basic pH conditions favored...
-
A Geometrically Simple Compact Wideband Circularly Polarized Antenna
PublikacjaA compact broadband wide-slot circular polarization (CP) antenna is proposed. An inverted L-shape parasitic strip at the open end of a microstrip line extension and a slot modification is applied to attain wideband CP. The advantage of this technique is simplicity which makes it readily re-designable for different frequency bands. To demonstrate the concept, three designs working at different frequencies are obtained. The redesign...
-
Numbers, Please: Power- and Voltage-Related Indices in Control of a Turbine-Generator Set
PublikacjaThis paper discusses the proper selection and interpretation of aggregated control performance indices values mirroring the quality of electrical energy generation by a turbine-generator set cooperating with a power system. Typically, a set of basic/classical and individual indices is used in energy engineering to ensure the mirroring feature and is related to voltage, frequency and active or reactive power deviations from their...
-
Milena Marycz dr inż.
Osoby -
EXPERIMENTAL EVALUATION OF DLC/STEEL SLIDING CONTACTS’ OPERATIONAL ENVELOPE
PublikacjaIn an industrial project concerning sliding bearings, a sliding pair was selected of high alloy steel vs. industrial grade DLC coated high alloy steel as a basis for an innovative design of high performance sliding bearings lubricated with a synthetic oil for use in geared transmission units. The development process required credible data on the ultimate resistance of the sliding pair to very high contact stress. An experimental...
-
High-Gain Compact Circularly Polarized X-Band Superstrate Antenna for CubeSat Applications
PublikacjaIn this letter, a concept of high-gain circularly polarized X-band antenna employing a partially reflecting surface (PRS) has been presented. In the initial antenna analysis, the influence of parasitic elements size in the PRS structure on antenna radiation pattern parameters has been investigated and the optimal arrangement of the elements has been identified. The proposed antenna provides wide bandwidth of return loss above 10...
-
Expedited Design Closure of Antenna Input Characteristics by Trust Region Gradient Search and Principal Component Analysis
PublikacjaOptimization-based parameter tuning has become an inherent part of contemporary antenna design process. For the sake of reliability, it is typically conducted at the level of full-wave electromagnetic (EM) simulation models. This may incur considerable computational expenses depending on the cost of an individual EM analysis, the number of adjustable variables, the type of task (local, global, single-/multi-objective optimization),...
-
Simulation of the weight averaging of pulse frequency modulated sensor output signal
Dane BadawczeThe aim of the research is investigation of the efficiency of weight averaging of pulse frequency modulated signal. It was shown that from the point of view of the reduction of the sampling error the best are polynomial weighing functions, for which the maximum of this component error decreases proportionally to the appropriate power of the number of...
-
Compact Dual-Polarized Corrugated Horn Antenna for Satellite Communications
PublikacjaIn this paper, a structure and design procedure of a novel compact dual-polarized corrugated horn antenna with high gain and a stable phase center for satellite communication is presented. The antenna incorporates an Ortho-Mode Transducer (OMT), a mode converter, and a corrugated structure. The compact OMT section is designed to be fed by standard WR-75 waveguides. The proposed compact design utilizes only ten corrugated slots...
-
Dangerous sound event recognition using Support Vector Machine classifiers
PublikacjaA method of recognizing events connected to danger based on their acoustic representation through Support Vector Machine classification is presented. The method proposed is particularly useful in an automatic surveillance system. The set of 28 parameters used in the classifier consists of dedicated parameters and MPEG-7 features. Methods for parameter calculation are presented, as well as a design of SVM model used for classification....
-
NUMERICAL ESTIMATION OF HULL HYDRODYNAMIC DERIVATIVES IN SHIP MANOUVERING PREDICTION
PublikacjaOperating in crowded waterways pose a risk of accidents and disasters due to maneuvering limitations of the ship. In order to predict ship’s maneuvering characteristics at the design stage, model tests are often executed as the most accurate prediction tool. Two approaches can be distinguished here: free running model tests and numerical simulations based on planar motion model with the use of hydrodynamic derivatives obtained...
-
Deflated Preconditioned Solvers for Parametrized Local Model Order Reduction
PublikacjaOne of steps in the design of microwave filters is numerical tuning using full-wave simulators. Typically, it is a time-consuming process as it uses advanced computational methods, e.g. the finite-element method (FEM) and it usually requires multiple optimization steps before the specification goals are met. FEM involves solving a large sparse system of equations at many frequency points and therefore its computational cost is...
-
The Development of a Combined Method to Quickly Assess Ship Speed and Fuel Consumption at Different Powertrain Load and Sea Conditions
PublikacjaDecision support systems (DSS) recently have been increasingly in use during ships operation. They require realistic input data regarding different aspects of navigation. To address the optimal weather routing of a ship, which is one of the most promising field of DSS application, it is necessary to accurately predict an actually attainable speed of a ship and corresponding fuel consumption at given loading conditions and predicted...
-
Application of Thermo-chemical Technologies for Conversion of Associated Gas in Diesel-Gas Turbine Installations for Oil and Gas Floating Units
PublikacjaThe paper considers the issue of thermo-chemical recovery of engine’s waste heat and its further use for steam conversion of the associated gas for oil and gas floating units. The characteristics of the associated gas are presented, and problems of its application in dual-fuel medium-speed internal combustion engines are discussed. Various variants of combined diesel-gas turbine power plant with thermo-chemical heat recovery are...
-
Optimization of the spindle speed during milling of large-sized structures with the use of technique of Experiment-Aided Virtual Prototyping
PublikacjaIn the paper are presented considerations concerning vibration suppression problems during milling of large-sized workpieces with the use of innovative method of matching the spindle speed of cutting tool. It depends on repeatable change of the spindle speed value as soon as the optimal vibration state of the workpiece approaches. The values of dominant “peaks” in the frequency spectra and the Root Mean Square (RMS) values of time...
-
Ultra-Compact SIRC-Based Self-Triplexing Antenna with High Isolation
PublikacjaAn ultra-compact self-triplexing antenna realized on a substrate-integrated rectangular cavity (SIRC) is discussed in this study. The proposed structure employs two L-shaped slots and an in-verted U-shaped slot to radiate at three independent operating frequency bands. Three 50-ohm microstrip feed lines are used to excite the radiation in these slots. The operating frequency is individually tuned using the slot size. The slot placement...
-
Ultra-Compact Self-Quadruplexing Microfluidically Frequency Reconfigurable Slot Antenna Using Half-Mode SIW
PublikacjaIn this brief, the design of an ultra-compact self-quadruplexing frequency reconfigurable antenna (SQFRA) utilizing a half-mode substrate-integrated waveguide (HMSIW) and microfluidic channels is discussed. Four HMSIW cavities fed by four microstrip lines and slots are used to construct a highly compact antenna. The microstrip feedings to the HMSIW cavities are applied in such a way that the proposed antenna exhibits self-quadruplexing...
-
Common-Mode Voltage and Bearing Currents in PWM Inverters: Causes, Effects and Prevention
PublikacjaIn modern induction motor drives an increase of transistors' switching frequency and a decrease of switching times are the sources of some serious problems. The high dv/dt and the common mode voltage generated by the inverter PWM control results in the appearances of bearing currents, shaft voltages, motor terminal overvoltages, the decrease of motor efficiency, and electromagnetic interference. The aspects of common mode (CM)...
-
Multi-transformer primary-side regulated flyback converter for supplying isolated IGBT and MOSFET drivers
PublikacjaThis paper presents primary-side voltage regulated multi-transformer quasi-resonant flyback converter (MTFC) for supplying isolated power switch drivers. The proposed topology offers distinct advantages over frequently used flyback converter possessing one high frequency transformer with isolated multiple outputs. Particularly, when a large number of separate dc supply units is required, then MTFC enables improved regular distribution...
-
Enhancing Resilience of FSO Networks to Adverse Weather Conditions
PublikacjaOptical wireless networks realized by means of gigabit optical wireless communication (OWC) systems are becoming, in a variety of applications, an important alternative, or a complementary solution, to their fiber-based counterparts. However, performance of the OWC systems can be considerably degraded in periods of unfavorable weather conditions, such as heavy fog, which temporarily reduce the effective capacity of the network....
-
Selected elements of the methodology and method of designing amphibious flood rescue vehicles
PublikacjaThe methodology of designing amphibious flood rescue vehicles at the preliminary stage of the design process has been presented. The study has been focused on the properties of such vehicles when afloat, with their on-land behaviour and performance characteristics having been left aside. In the study, a general assumption has been made that the amphibious flood rescue vehicles should be designed as, above all, watercraft that additionally...
-
Low-cost multi-objective optimization of antennas using Pareto front exploration and response features
PublikacjaIn the paper, a procedure for low-cost multi-objective optimization of antenna structures is presented. Our approach is based on exploration of the Pareto front representing the best possible trade-offs between conflicting objectives, here, the structure size and its electrical performance. Starting from the design representing the best in-band reflection level, subsequent Pareto-optimal designs are identified through local constrained...
-
Dynamic model of nuclear power plant turbine
PublikacjaThe paper presents the dynamic multivariable model of Nuclear Power Plant steam turbine. Nature of the processes occurring in a steam turbine causes a task of modeling it very difficult, especially when this model is intended to be used for on-line optimal process control (model based) over wide range of operating conditions caused by changing power demand. Particular property of developed model is that it enables calculations...
-
How does stakeholder pressure influence CSR-practices? A construction industry model based on a European sample
PublikacjaThe stakeholder pressure is one of the most vital powers which determines CSR implementation and can provide organizations with the motivation to adopt corporate social responsibility (CSR) strategy, as the stakeholder theory claims. The current investigation replications Kowalczyk’s (2019) study, who examined the same structure of relations based on the Polish sample. The essence of this replication is to find out whether CSR-...
-
Ni-based compounds in multiwalled graphitic shell for electrocatalytic oxygen evolution reactions
Dane BadawczeThis study investigates Ni-based compounds (Ni, NiO, Ni3C) coated with a graphitic shell as electrocatalysts for the oxygen evolution reaction (OER). Electron paramagnetic resonance (EPR) and X-ray diffraction (XRD) are employed to identify the presence and contribution of Nickel ions (Ni0, Ni2+, Ni3+) and determine the phase composition. Electrochemical...
-
Multiple output second-generation current conveyor utilizing high frequency output stage
PublikacjaIn this paper a multiple output second-generation current conveyor (MOCCII) is presented. The main advantage of the proposed general circuit architecture over a typical structure, well known in the literature, is the use of a high passband multiple output current mplifier block instead of cascaded current mirrors. It gives similar frequency responses for all the outputs of the current conveyor and also maintains simplicity of the...
-
Jaroslaw Spychala dr
OsobyOprócz bardzo dobrego wykształcenia osoba posiada również wieloletnie doświadczenie zawodowe, które jest poświadczeniem tego, że potrafi wykorzystać swoją wiedzę teoretyczną w praktycznych działaniach. Doświadczenie zawodowe jest bardzo bogate i rozbudowane. Ze względu na nabyte całkiem nowe umiejętności zwiększa się atrakcyjność doświadczonego pracownika. Są to między innymi kreatywne myślenie, zorientowanie na cel, odporność...
-
Multi-objective optimization of the cavitation generation unit structure of an advanced rotational hydrodynamic cavitation reactor
PublikacjaHydrodynamic cavitation (HC) has been widely considered a promising technique for industrial-scale process intensifications. The effectiveness of HC is determined by the performance of hydrodynamic cavitation reactors (HCRs). The advanced rotational HCRs (ARHCRs) proposed recently have shown superior performance in various applications, while the research on the structural optimization is still absent. The present study, for the...
-
Low-Voltage LDO Regulator Based on Native MOS Transistor with Improved PSR and Fast Response
PublikacjaIn this paper, a low-voltage low-dropout analog regulator (ALDO) based on a native n-channel MOS transistor is proposed. Application of the native transistor with the threshold voltage close to zero allows elimination of the charge pump in low-voltage regulators using the pass element in a common drain configuration. Such a native pass transistor configuration allows simplification of regulator design and improved performance,...
-
Combining X-ray tomogrpahy imaging and DEM simulations to investigate granular material flow during silo discharging
PublikacjaEven after few decades of research, the study of particle motion taking place during silo discharging hasn’t been fully addressed, both experimentally and numerically, because of nontrivial behaviors that occur during associated flow patterns. For instance, discrete element method (DEM) has shown good qualitative prediction potential of velocity profile, but, on the other hand, frequently failed to match quantitatively experimental...
-
Ruchotwórczość wielkopowierzchniowych obiektów handlowych trzeciej generacji na przykładzie Trójmiasta
PublikacjaWielkopowierzchniowe obiekty (handlowe, usługowe itp.) generują ruch o dużych natężeniach, które często przekraczają możliwości przepustowe przyległego układu ulicznego. Wpływają w ten sposób na znaczne pogorszenie się warunków ruchu w najbliższym otoczeniu obiektu i zakłócenia w prawidłowym funkcjonowaniu systemu transportowego miasta. Wobec braku polskich doświadczeń konieczne jest badanie wpływu wybranych czynników demograficznych,...
-
Modelling hydraulic and capillary-driven two-phase fluid flow in unsaturated concretes at the meso-scale with a unique coupled DEM-CFD technique
PublikacjaThe goal of the research was to demonstrate the impact of thin porous interfacial transition zones (ITZs) between aggregates and cement matrix on fluid flow in unsaturated concrete caused by hydraulic/capillary pressure. To demonstrate this impact, a novel coupled approach to simulate the two-phase (water and moist air) flow of hydraulically and capillary-driven fluid in unsaturated concrete was developed. By merging the discrete...
-
PROJEKTOWANIE WIELOWYMIAROWEGO REGULATORA BACKSTEPPING W UKŁADZIE DYNAMICZNEGO POZYCJONOWANIA STATKU
PublikacjaW komercyjnych systemach dynamicznego pozycjonowania statku, pomimo znacznego wzrostu poziomu automatyzacji, wykorzystywane jest nadal sterowanie typu PID. Poprawę jakości procesu pozycjonowania może umożliwić wykorzystanie bardziej efektywnych algorytmów, oferujących zaawansowane nieliniowe techniki sterowania. W artykule przedstawiono zagadnienie projektowania regulatora pozycji i kursu dla układu dynamicznego pozycjonowania...
-
On tracking properties of real-valued generalized adaptive notch filters
PublikacjaGeneralized adaptive notch filters (GANFs) are used for identification/tracking of quasi-periodically varying dynamic systems and can be considered an extension, to the system case, of classical adaptive notch filters. The paper presents results of local performance analysis of a real-valued GANF algorithm, i.e., algorithm designed to track parameters of a real-valued system. This is an extension of the previous work which focused...
-
Multi Queue Approach for Network Services Implemented for Multi Core CPUs
PublikacjaMultiple core processors have already became the dominant design for general purpose CPUs. Incarnations of this technology are present in solutions dedicated to such areas like computer graphics, signal processing and also computer networking. Since the key functionality of network core components is fast package servicing, multicore technology, due to multi tasking ability, seems useful to support packet processing. Dedicated...
-
A Series-Inclined-Slot-Fed Circularly Polarized Antenna for 5G 28-GHz Applications
PublikacjaThis letter presents the design of a single-point-fed, geometrically simple circularly polarized (CP) antenna for 28 GHz Ka-band applications. The proposed antenna is based on a straight microstrip line printed on one side and coupled with the nearly square patches through a 45-degree inclined V-shape slot aperture on the other side. In order to generate circular polarization, the fundamental radiating mode is degenerated at a...
-
Rapid Antenna Optimization with Restricted Sensitivity Updates by Automated Dominant Direction Identification
PublikacjaMeticulous tuning of geometry parameters turns pivotal in improving performance of antenna systems. It is more and more often realized using formal optimization methods, which is demonstrably the most efficient way of handling multiple design variables, objectives, and constraints. Although in some cases a need for launching global search arises, a typical design scenario only requires local optimization, especially when a decent...
-
Novel Versatile Topologies and Design Optimization of Wide-Bandstop Frequency Selective Surfaces for X-Band, Ku-Band and Millimeter-Wave Applications
PublikacjaNovel designs of frequency selective surface (FSS) are presented for wideband applications in X, Ku and mmWave (millimeter Wave) bands. Two identical metallic layers of FSS are imprinted on both sides of the RO4003 substrate. The geometry parameters are optimized to maximize the bandstop at the specified in-band maximum transmission level of –10 dB; satisfaction of the latter condition is enforced through appropriate formulation...
-
Near Field Coupled Wireless Microwave Sensor
PublikacjaThis paper presents a wireless planar microwave sensor operating at industrial scientific and medical (ISM) frequency for the detection of dielectric materials. The microwave sensor consists of a reader (ground defected microstrip coupled line) and a passive tag where a complementary split-ring resonator (CSRR) is made on the commercially available copper-foil. The CSRR is a peel-off type tag that is excited using the near field...
-
Dynamic Modeling of COVID-19 Disease with Impact of Lockdown in Pakistan and Malaysia
PublikacjaBeing researchers, it is an utmost responsibility to provide insight on social issues thus, this work addresses the dynamic modeling of first and most contagious disease named as COVID-19 caused by coronavirus. The first case of COVID-19 appeared in Pakistan was on 26th February 2020 and in Malaysia on 27th February 2020; both patients had foreign travel history. In the paper, the number of total affected cases and total deaths...
-
Energy-Aware Scheduling for High-Performance Computing Systems: A Survey
PublikacjaHigh-performance computing (HPC), according to its name, is traditionally oriented toward performance, especially the execution time and scalability of the computations. However, due to the high cost and environmental issues, energy consumption has already become a very important factor that needs to be considered. The paper presents a survey of energy-aware scheduling methods used in a modern HPC environment, starting with the...