Wyszukiwarka
Wyniki wyszukiwania dla: friction, afc coating
-
Tribo-Environment Dependent Chemical Modification of Sliding Interfaces in Ultrananocrystalline Diamond Nanowall Film: A Correlation with Friction and Wear
PublikacjaTribological properties of ultrananocrystalline diamond nanowall (UNCD NW) films were investigated quantitatively in three different and controlled tribo-environmental conditions, proposing the passivation and graphitization mechanisms. However, these mechanisms are rather complicated and possibly can be understood in well-controlled tribological conditions. It was shown that the friction and wear of these films were high in highPage 1...
-
Correlations between the wear of car brake friction materials and airborne wear particle emissions
PublikacjaAirborne wear particles emitted from transport vehicle brakes are one of the main sources of toxic metals in inhalable particulate matter. Prediction of wear particle emissions may become more accurate if the relationship between the wear and particle emission characteristics is known. An experimental study was performed to investigate proportional correlations between the mass wear, 0.01–0.42 μm particle emission measured by a NanoScan...
-
Flow and friction around the growing cartilage cells
PublikacjaInżynieria tkankowa jest jedną z najszybciej rozwijających się dziedzin biotechnologii stosowanej. Nowe metody badawcze tej nauki mogą być rozwiązane jedynie przy wzajemnej współpracy biologów, tribologów, mechaników, ortopedów klinicystów.Schorzenia chrząstki stawowej dotyczą milionów ludzi na świecie, często nawet w młodym wieku. Od kilkunastu lat z powodzeniem prowadzone są próby rekonstrukcji chrząstki stawowej oparte na dwóch...
-
The influence of contact geometry on friction and wear characteristics
Publikacja -
Friction induced vibrations in sliding of monolithic alumina
PublikacjaPrzedstawiono wyniki badań wzbudzania się (i ewentualnie - zaniku) drgań mechanicznych towarzyszących tarciu ślizgowemu próbek o płaskiej powierzchni styku, wykonanych z monolitycznego tlenku aluminium. Badano wpływ wymuszeń tribologicznych oraz dynamicznych cech układu badawczego na przebieg zjawiska.
-
Internal friction in FePd alloy during ordering
PublikacjaStwierdzono występowanie wysokiego poziomu tarcia wewnętrznego w zahartowanym stopie FePd (50% at. Pd). Zbadano proces uporządkowania atomowego w korelacji ze zmianami tarcia wewnętrznego defektu modułu i relaksacji magnetycznej stopu porządkującego się podczas nagrzewania do 900 K. Zaobserwowano efekt prędkości nagrzewania na punkt Curie.
-
Developments in unsteady pipe flow friction modelling
PublikacjaW pracy omówiono wpływ błędów numerycznych na jakość rozwiązania równań uderzenia hydraulicznego. Wykazano rolę dyfuzji numerycznej i jej wpływ na dokładność rozwiązania w porównaniu z członem tarcia.
-
Emission and properties of airborne wear particles from train brake friction materials based on novolac phenolic resins and butadiene rubbers
PublikacjaThe emission of airborne particulate matter from a train brake depends on the formulation of its friction material. This study investigates the emission and properties of wear particles from train brake friction materials based on straight or resorcinol-modified novolac phenolic resin and nitrile or styrene butadiene rubber used as binding ingredients. The wear particles are generated by a pin-on-disc tribomachine inside an aerodynamic...
-
Effective yttrium based coating for steel interconnects of solid oxide cells: Corrosion evaluation in steam-hydrogen atmosphere
PublikacjaThis work describes manufacture, analysis and test of a new well conducting corrosion-protection coating that can be applied on steel types with high chromium content. Electrolytic deposition of yttrium salts is used to form thin (<100 nm) coatings on both flat steel sheets (material: Crofer 22 APU) and its properties are proven on woven wire-meshes (materials from two different sources: SUS316 and SUS316L). The oxide scale on...
-
Effects of electrophoretic deposition times and nanotubular oxide surfaces on properties of the nanohydroxyapatite/nanocopper coating on the Ti13Zr13Nb alloy
PublikacjaLoad-bearing implants are developed with a particular emphasis placed on an application of ceramic hydroxyapatite coatings in order, to enhance the bioactivity of titanium implants and to shorten the healing time. Therefore, thin, fully crystalline coatings that are, highly adhesive, hydrophilic and demonstrating antibacterial properties are ly looked for. The aim of this research was to develop and characterize the properties...
-
Multivariate analysis of impedance data obtained for coating systems of varying thickness applied on steel
PublikacjaElectrochemical impedance spectroscopy (EIS) has proven to be a valuable test method for the electrochemical characterization of protective coatings on metals. The common way of analysis in impedance spectroscopy is to model the impedance spectrum by means of an equivalent circuit and to extract the quantity of interest using optimization techniques. A model, corresponding to the behavior of the sample under testing, is important...
-
Drop-coating deposition surface-enhanced Raman spectroscopy on silver substrates for biofluid analysis
PublikacjaUtilization of surface-enhanced Raman spectroscopy as a measurement technique is of particular interest in biodetection due to its superb chemical specificity and high sensitivity. The use of SERS substrates further improve this method by massive enhancement of the molecule Raman spectrum, permitting very low levels of detection. Therefore it is important to seek for new ways to develop reliable substrates, which are quickly and...
-
Study on Dry Sliding Wear and Friction Behaviour of Al7068/Si3N4/BN Hybrid Composites
PublikacjaHybrid aluminium metal matrix composites have the potential to replace single reinforced aluminium metal matrix composites due to improved properties. Moreover, tribological performance is critical for these composites, as they have extensive application areas, such as the automotive, aerospace, marine and defence industries. The present work aims to establish the tribological characteristics of Al7068/Si3N4/BN hybrid metal matrix...
-
Effect of underwater friction stir welding parameters on AA5754 alloy joints: experimental studies
PublikacjaThe water as a welding environment may generate serious technological and metallurgical problems but in certain cases, the physicochemical properties of water can be used effectively, e.g., to impart the specific properties of welded materials. The purpose of the work was verification of effectiveness of the water cooling of aluminium alloy AA5754 for various sets of technological parameters of underwater friction stir welding...
-
Imaging and chemical investigation of silver coating
Dane BadawczeThe recovery of silver from materials such as plates, still used in clinical radiography [1], or scrap jewelery is still very popular. The subject of the research, part of which was microscopic imaging, was to recreate the behavior of an electrochemically deposited silver coating. The copper electrodes were covered with a layer of silver obtained from...
-
Induction Assisted Hybrid Friction Stir Welding of Dissimilar Materials AA5052 Aluminium Alloy and X12Cr13 Stainless Steel
PublikacjaThis research aimed to study the induction in-situ heated hybrid friction stir welding (IAFSW) method to join AA5052 aluminium alloy with X12Cr13 stainless steel (SS) to enhance joint strength. The potency of this method on the mechanical properties and microstructural characterizations were also investigated. The results show that the transverse tensile strength gained was 94% of the AA5052 base metal that is 229.5 MPa. This superior...
-
The lubricant-coating interaction in rolling and sliding contacts
Publikacja -
Evaluation of coating systems using impedance spectroscopy
PublikacjaTrwałość powłokowych systemów ochronnych zależy od oddziaływań środowiska i związana jest nieodwracalnymi procesami chemicznymi i fizycznymi. Zastosowanie spektroskopii impedancyjnej pozwala na określenie obszaru zastosowań danej powłoki i prognozowanie okresu jej trwałości. W pracy zamieszczono przykłady oceny trwałości systemów powłokowych stosowanych w strategicznych konstrukcjach.
-
Impedance measurements of coating properties on bridge structures
PublikacjaPomiary impedancyjne pozwalają na prostą ocenę właściwości ochronnych powłok ochronnych i wykładzin. Pomiary stosuje się w celu porównania powłok, monitorowania ich właściwości i oceny mechanizmu działania. Metodyka jest z powodzeniem stosowana w pomiarach laboratoryjnych. Pomiary terenowe są bardziej skomplikowane ponieważ wymagają w pełni kontrolowanych komputerowo przyrządów, kontroli warunków pogodowych oraz wielu innych parametrów...
-
Hydroxyapatite films as biocompatibile coating for artifical bone
PublikacjaW artykule została szczegółowo opisana budowa kości oraz materiał biokompatybilny hydroksyapatyt (HAp). Autorzy wykazali jak wielkie podobieństwo do budowy kości przejawia sztuczny hydroksyapatyt. opisali syntezy powłoki z HAp.
-
Ecology In Tribology: Selected Problems of Eliminating Natural Oil-Based Lubricants from Machine Friction Couples
PublikacjaThe elimination of mineral oil-based lubricants from machines has multiple beneficial effects on the natural environment. Firstly – these lubricants are a direct threat to the environment in the event of leaks; secondly – their elimination reduces the demand for crude oil from which they are obtained. In addition, in many cases, e.g. when replacing traditional lubricants with water, friction losses in the bearings can also be reduced...
-
Electrochemically assisted deposition of hydroxyapatite on Ti6Al4V substrates covered by CVD diamond films — Coating characterization and first cell biological results
PublikacjaAlthough titaniumand its alloys are widely used as implant material for orthopedic and dental applications they show only limited corrosion stability and osseointegration in different cases. The aim of the presented research was to develop and characterize a novel surface modification system from a thin diamond base layer and a hydroxyapatite (HAp) top coating deposited on the alloy Ti6Al4V widely used for implants in contact with bone....
-
Experimental measurements of friction forces on the tissue in probabilistic view
PublikacjaNiniejsza praca jest poświęcona wyznaczaniu wartości sił tarcia wywołanych podczas hydrodynamicznego przepływu lepkosprężystej cieczy odżywczej na powierzchniach hodowanych chondrocytów w bioreaktorze. Badania realizuje się w nano skali przy wykorzystaniu mikroskopu sił atomowych. Chondrocyty hodujemy w celu naprawy uszkodzonych chrząstek stawowych kolana człowieka.
-
Micromechanical analysis of friction anisotropy in rough elastic contacts
Publikacja -
EFFECT OF THE BIO-LUBRICANT ON THE LUBRICATINGPROPERTIES AND SURFACE OF THE FRICTION ZONE
Publikacja -
Comparative investigation of lubricant properties in friction and wear tests
PublikacjaOpisano porównawcze badania obciążenia zacierania na tribometrze PT3, obciążenia zespawania na aparacie czterokulowym i zużycia frettingowego na stanowisku FRET3, sześciu olejów smarowych i sześciu smarów plastycznych. Próbki do badań na stanowiskach PT3 i FRET3 wykonane były ze stali 35.
-
Preliminary design of the last stage of supercritical steam turbine and proposition of anti-erosion coating for blades surface
PublikacjaIn this article a preliminary design of the last stage of supercritical steam turbine has been presented. A computational model of supercritical thermal cycle has been created in order to determine steam parameters at the stage inlet and outlet. The model was based on the structure of German coal-fired power plant Datteln 4. Further steam-flow parame-ters and dimensions of stator and rotor blades have been calculated analytically....
-
Bioactive and biodegradable cotton fabrics produced via synergic effect of plant extracts and essential oils in chitosan coating system
PublikacjaFunctional antibacterial textile materials are in great demand in the medical sector. In this paper, we propose a facile, eco-friendly approach to the design of antibacterial biodegradable cotton fabrics. Cotton fiber fabrics were enhanced with a chitosan coating loaded with plant extracts and essential oils. We employed Fourier-transform infrared (FTIR) and X-ray photoelectron spectroscopy (XPS), UV–Vis spectrophotometry, optical...
-
Physicochemical properties of Mn1.45Co1.45Cu0.1O4 spinel coating deposited on the Crofer 22 H ferritic steel and exposed to high-temperature oxidation under thermal cycling conditions
PublikacjaThe Crofer 22 H ferritic steel substrate was coated with an Mn1.45Co1.45Cu0.1O4 spinel by means of electrophoresis. After high-temperature oxidation under thermal cycling conditions, the physicochemical properties of the obtained system were evaluated. During 48-h cycles that involved heating the samples up to temperatures of either 750 or 800 °C, the oxidation kinetics of both coated and unmodified steel approximately obeyed...
-
Analytical solution of non-stationary heat conduction problem for two sliding layers with time-dependent friction conditions
PublikacjaIn this article we conduct an overview of various types of thermal contact conditions at the sliding interface. We formulate a problem of non-stationary heat conduction in two sliding layers with generalized thermal contact conditions allowing for dependence of the heat-generation coefficient and contact heat transfer coefficient on time. We then derive an analytical solution of the problem by constructing a special coordinate...
-
Analysis of Residual Stresses and Dislocation Density of AA6082 Butt Welds Produced by Friction Sir Welding
PublikacjaThe Friction Stir Welding (FSW) method was employed to join AA6082 sheets. The welds were produced with different tool traverse speed (200 and 250 mm/min), rotational speed (1000 and 1250 RPM) and tool tilt angle (0 and 2 deg). Based on the analysis of XRD patterns, the total precipitation volume fractions in the nugget zones and the base material were calculated. The FSW process resulted in a reduction in the fraction of precipitates...
-
Improved model of isothermal and incompressible fluid flow in pipelines versus the Darcy–Weisbach equation and the issue of friction factor
PublikacjaIn this article, we consider the modelling of stationary incompressible and isothermal one-dimensional fluid flow through a long pipeline. The approximation of the average pressure in the developed model by the arithmetic mean of inlet and outlet pressures leads to the known empirical Darcy–Weisbach equation. Most importantly, we also present another improved approach that is more accurate because the average pressure is estimated...
-
Preparation and Characterization of Microsphere ZnO ALD Coating Dedicated for the Fiber-Optic Refractive Index Sensor
PublikacjaWe report the fabrication of a novel fiber-optic sensor device, based on the use of a microsphere conformally coated with a thin layer of zinc oxide (ZnO) by atomic layer deposition (ALD), and its use as a refractive index sensor. The microsphere was prepared on the tip of a single-mode optical fiber, on which a conformal ZnO thin film of 200 nm was deposited using an ALD process based on diethyl zinc (DEZ) and water at 100 °C....
-
Improved surface coverage of an optical fibre with nanocrystalline diamond by the application of dip-coating seeding
PublikacjaGrowth processes of diamond thin films on the fused silica optical fibres (10 cm in length) were investigated at various temperatures. Fused silica pre-treatment by dip-coating in a dispersion consisting of detonation nanodiamond (DND) in dimethyl sulfoxide (DMSO) with polyvinyl alcohol (PVA) was applied. Nanocrystalline diamond (NCD) films were deposited on the fibres using the microwave plasma assisted chemical vapour deposition...
-
The Effect of Marginal Zn2+ Excess Released from Titanium Coating on Differentiation of Human Osteoblastic Cells
PublikacjaComposite coatings based on chitosan and zinc nanoparticles (ZnNPs) were successfully produced on Ti13Zr13Nb substrates by cathodic electrophoretic deposition (EPD). The unfavorable phenomenon of water electrolysis-induced nonuniformity was reduced by applying a low voltage (20 V) and a short deposition time (1 min). Surface analysis (roughness and hydrophilicity) reveals the potential of these coatings for enhancing cell attachment...
-
Pin Angle Thermal Effects on Friction Stir Welding of AA5058 Aluminum Alloy: CFD Simulation and Experimental Validation
PublikacjaThe friction stir welding (FSW) of tool pin geometry plays a critical role in the final properties of the produced joint. The tool pin geometry directly affects the generation of heat and the flow of internal materials during the FSW process. The effects of the FSW tool pin angle on heat generation and internal flow have not been quantitatively investigated in detail. In this manuscript, a validated Computational Fluid Dynamic...
-
Accelerated ageing of organic coating systems by thermal treatment
Publikacja -
Special Issue “Corrosion Resistance of Alloy and Coating Materials”
Publikacja -
Bio-based semi-aromatic polyesters for coating applications
PublikacjaLinear and branched bio-based semi-aromatic (co)polyesters were evaluated as resins for solvent-basedand powder coatings. Dimethyl-2,5-furandicarboxylate (DMF), 2,3-butanediol and various multifunc-tional comonomers were used to synthesize amorphous hydroxyl-end-capped (co)polyesters. The resinswere cross-linked using the -caprolactam blocked trimer of isophorone diisocyanate. Both the solvent-based and powder coatings proved to...
-
Effect of Tool Positioning Factors on the Strength of Dissimilar Friction Stir Welded Joints of AA7075-T6 and AA6061-T6
PublikacjaFriction Stir Welding (FSW) is a solid-state bonding technique. There are many direct and indirect factors affecting the mechanical and microstructural properties of the FSW joints. Tool offset, tilt angle, and plunge depth are determinative tool positioning in the FSW process. Investigating the effect of these factors simultaneously with other parameters such as process speeds (rotational speed and translational speed) and tool...
-
Shaft friction from the DMT and direct shear interface tests
PublikacjaThe article presents preliminary attempt to create tri-linear transfer curves for describing pile behaviour under axial loading. Transfer curves would use the parameter measured in dilatometer test, particularly a constrained modulus MDMT. The proposed method is based on concrete rough and smooth interface tests performed in a direct shear apparatus. Based on the obtained mobilization curves, relationships were created between...
-
Scale effect in shaft friction from direct shear tests
PublikacjaPrzeanalizowano wartości maksymalne tarcia uzyskane w aparacie bezpośredniego ścinania w kontakcie konstrukcja-grunt dla piasków kwarcowych i węglanowych oraz gładkiego i szorstkiego kontaktu. Badania przeprowadzono przy regulowanej sztywności normalnej kontaktu, przy różnej składowej normalnej naprężenia w kontakcie i różnym zagęszczeniu gruntu. Określono efekt skali jako stosunek wartości tarcia mobilizowanego na modelu do tarcia...
-
Friction stir welds (FSW) of aluminium alloy AW6082-T6
PublikacjaW pracy przedstawiono badania właściwości mechanicznych złącz stopu aluminium AW6082-T6 wykonanych metodą tarciowego zgrzewania z wymieszaniem zgrzeiny. Złącza wykonano z różnymi parametrami procesu technologicznego. Wykazano, że wytrzymałość złącz jest proporcjonalna do prędkości zgrzewania oraz, że spadek twardości SWC jest większy po stronie ''advancing'' złącz.
-
Friction forces for human hip joint at a naturally permeable cartilage
PublikacjaNiniejsza praca omawia różne rodzaje sił tarcia występujących w szczelinach stawów człowierka. W artykule dokonano analizy kilku ważnych czynników wpływających na wartości sił tarcia występujących w stawach człowieka. Rozważa się siły tarcia wywołane klasycznym hydrodynamicznym smarowaniem, wzmożonym hydrodynamicznym smarowaniem, wyciskaniem a także przesączaniem cieczy synowialnej do i z porowatej warstwy chrząstki stawowej.
-
Computational studies of friction forces for hard tissue cultivation in bioreactor.
PublikacjaPonieważ wymiana naturalego stawu na endoprotezę może być dokonywana 2-3 razy w życiu, problem leczenia przez transplantację tkanek chrzęstnych nabiera dużego znaczenia. Przeszczepów tkanki można dokonywać z sukcesem wiele razy. W bioreaktorach, środowisko hydrodynamiczne kształtuje hodowlę tkanek in vitro w obecności sił tarcia, poprzez bezpośrednie działanie na morfologię komórek a także poprzez pośrednie działanie na tkankę...
-
Examples of retrofit of structures on seismic areas by friction pendulum system.
PublikacjaZastosowanie łożysk wahadłowych, w których dyssypacja energii następuje na skutek tarcia, to jedna z najbardziej obiecujących metod wzmacniania odporności sejsmicznej budowli. Celem artykułu jest przedstawienie przykładów zastosowania tej metody do różnych typów konstrukcji budowlanych narażonych na wstrząsy sejsmiczne.
-
Internal friction in pure Co and CoPt alloy during ordering
PublikacjaZbadano tarcie wewnętrzne, wskaźnik modułu sprężystości postaciowej i podatność magnetyczną stopu CoPt (50% at. Pt) w stanie nieuporządkowanym, uzyskanym w wyniku oziębienia, podczas wyżarzania do 850 K przy wzrostach temperatury 6K/min. i 2K/min., stosując odwróconą skręcarkę wahadłową. Zaobserwowano maksimum tarcia wewnętrznego w CoPt przy 700 K oraz w monokrysztale kobaltu w 720 K w pobliżu martenzytycznej przemiany fazowej,...
-
Tesla Friction-Type Micro Turbine For Small-Scale Cogeneration
PublikacjaTesla turbine is rarely used in professional power installations due to its specific work characteristics and relatively low internal efficiency. However, it has some potential to be applied in micro-power plants operating in distributed co-generation systems, also working in an organic Rankine cycle. This paper presents results from numerical calculations of flow in three models of Tesla disk turbines assuming nitrogen as a working...
-
Comparative analysis of seismic response reduction in multi-storey buildings equipped with base isolation and passive/active friction-tuned mass dampers
PublikacjaThis study presents an innovative approach to mitigating seismic responses in multi-storey buildings equipped with a base-isolation (BI) system and passive friction-tuned mass dampers (PFTMDs). The key innovation lies in the combined use of a BI system and a PFTMD system, as well as the activation of this mechanical system by controllers. Additionally, the research design optimizes the parameters of these devices specifically for...
-
A new type of (TiZrNbTaHf)N/MoN nanocomposite coating: Microstructure and properties depending on energy of incident ions
PublikacjaA novel (TiZrNbTaHf)N/MoN nanocomposite coatings, which consist of the nitride of the high-entropy alloy and the binary nitride, were synthesized by vacuum-arc deposition at various substrate biases. The elemental composition, chemical bonding state, phase structure, microstructure and mechanical properties of the coatings were studied by high-resolution experimental methods: SIMS, GDMS, XPS, XRD, HR-TEM and nano-indentation. It...