Filtry
wszystkich: 275
Wyniki wyszukiwania dla: melting temperature
-
ELECTRICAL CONDUCTIVITY AND pH IN SURFACE WATER AS TOOL FOR IDENTIFICATION OF CHEMICAL DIVERSITY
PublikacjaIn the present study, the creeks and lakes located at the western shore of Admiralty Bay were analysed. The impact of various sources of water supply was considered, based on the parameters of temperature, pH and specific electrolytic conductivity (SEC25). All measurements were conducted during a field campaign in January-February 2017. A multivariate dataset was also created and a biplot of SEC25 and pH of the investigated waters...
-
Green monoterpenes based deep eutectic solvents for effective BTEX absorption from biogas
PublikacjaThe combustion of biogas which contains significant amounts of monoaromatic hydrocarbons, i.e. benzene, ethylbenzene, toluene, and xylene (BTEX) can cause many technological, environmental, and health problems. Therefore, in these studies, a new physical absorption method based on deep eutectic solvents (DES) consisting of monoterpenes and carboxylic acids was developed for BTEX removal. A total of 39 DES were synthesized, of which...
-
Significant Production of Thermal Energy in Partially Ionized Hyperbolic Tangent Material Based on Ternary Hybrid Nanomaterials
PublikacjaNanoparticles are frequently used to enhance the thermal performance of numerous materials. This study has many practical applications for activities that have to minimize losses of energy due to several impacts. This study investigates the inclusion of ternary hybrid nanoparticles in a partially ionized hyperbolic tangent liquid passed over a stretched melting surface. The fluid motion equation is presented by considering the...
-
Evaluation of polycaprolactone as a new sorbent coating for determination of polar organic compounds in water samples using membrane–SPME
PublikacjaCommercially available solid-phase microextraction fibers used for isolation of polar analytes are based on the adsorption phenomenon. In consequence, typical limitations bonded with analytes displacement and matrix effects are very frequent. In the present study, alternative solution is described. Polycaprolactone (PCL) was used for the first time as sorbent to isolate polar organic compounds from water samples using the membrane–solid-phase...
-
Quantification of Compatibility Between Polymeric Excipients and Atenolol Using Principal Component Analysis and Hierarchical Cluster Analysis
PublikacjaAn important challenge to overcome in the solid dosage forms technology is the selection of the most biopharmaceutically efficient polymeric excipients. The excipients can be selected, among others, by compatibility studies since incompatibilities between ingredients of the drug formulations adversely affect their bioavailability, stability, efficacy, and safety. Therefore, new, fast, and reliable methods for detecting incompatibility...
-
Magnetic deep eutectic solvents as efficient media for extraction of furfural and 5-hydroxymethylfurfural from aqueous samples
PublikacjaThe extraction of furfural (FF) and 5-hydroxymethylfurfural (HMF) from hydrolysates is currently one of the main challenges in bio-refinery. In this work, the separation of FF and HMF from the aqueous phase was carried out using a new type of green solvents – Magnetic Deep Eutectic Solvents (MDES). A conductor-like screening model for realistic solvents (COSMO-RS) was used for the preselection of 400 MDES. MDES which exhibit the...
-
Identification and characterization of single-stranded DNA-binding protein from the facultative psychrophilic bacteria Pseudoalteromonas haloplanktis
PublikacjaSingle-stranded DNA-binding protein (SSB) plays an important role in DNA metabolism such as DNAreplication, repair, and recombination, and is essential for cell survival. This study reports on the ssb-likegene cloning, gene expression and characterization of a single-stranded DNA-binding protein of Pseudoal-teromonas haloplanktis (PhaSSB) and is the first report of such a protein from psychrophilic microorganism.PhaSSB possesses...
-
Environmental characteristics of a tundra river system in Svalbard. Part 1: Bacterial abundance, community structure and nutrient levels
PublikacjaThe Arctic hosts a set of unique ecosystems, characterised by extreme environmental conditions and undergoing a rapid change resulting from the average temperature rising. We present a study on an aquatic ecosystem of the Revelva catchment (Spitsbergen), based on samples collected from the lake, river and their tributaries, in the summer of 2016. The landscape variety of the study site and the seasonal change in the hydrological...
-
Comparison of hydrochemistry and organic compound transport in two non-glaciated high Arctic catchments with a permafrost regime (Bellsund Fjord, Spitsbergen)
PublikacjaAn increase in air temperature related to climate change results in the retreat of glaciers, the degradation of permafrost, and the expansion of glacier-free areas in the polar regions. All these processes lead to changes in the Arctic landscape. They influence the hydrochemistry of streams and rivers fed by glaciers and thawing permafrost. In this study, we examine eighty two water samples from two non-glaciated catchments with...
-
An Investigation of Polyamides Based on Isoidide-2,5-dimethyleneamine as a Green Rigid Building Block with Enhanced Reactivity
PublikacjaNovel, semicrystalline polyamides and copolyamides were synthesized from a new carbohydrate-based diamine, namely isoidide-2,5-dimethyleneamine (IIDMA). In combination with 1,6-hexamethylene diamine (1,6-HDA) as well as the biobased sebacic acid (SA) or brassylic acid (BrA), the desired copolyamides were obtained via melt polymerization of the nylon salts followed by a solid-state polycondensation (SSPC) process. Depending on the...
-
Properties of surface layers of titanium alloy Ti6Al4V after laser melting processes
PublikacjaThe article presents the investigation results of titanium alloy Ti6Al4V surface layer after laser melting process. The process of laser melting was performed using Nd-YAG laser. The evaluation of structure of the alloy as well as hardness and chemical composition was performed. It was shown that laser melting changes the structure and properties of titanium alloy Ti6Al4V and process parameters as scanning speed affects the thickness...
-
Characterization of a single-stranded DNA-binding-like Protein from Nanoarchaeum equitans - a nucleic acid binding protein with broad substrate specificity
PublikacjaBackground SSB (single-stranded DNA-binding) proteins play an essential role in all living cells and viruses, as they are involved in processes connected with ssDNA metabolism. There has recently been an increasing interest in SSBs, since they can be applied in molecular biology techniques and analytical methods. Nanoarchaeum equitans, the only known representative of Archaea phylum Nanoarchaeota, is a hyperthermophilic, nanosized,...
-
Characterization of single-stranded DNA-binding proteins from the psychrophilic bacteria Desulfotalea psychrophila, Flavobacterium psychrophilum, Psychrobacter arcticus, Psychrobacter cryohalolentis, Psychromonas ingrahamii, Psychroflexus torquis, and Photobacterium profundum
PublikacjaBackground: Single-stranded DNA-binding proteins (SSBs) play essential roles in DNA replication, recombination and repair in Bacteria, Archaea and Eukarya. In recent years, there has been an increasing interest in SSBs, since they find numerous applications in diverse molecular biology and analytical methods. Results: We report the characterization of single-stranded DNA-binding proteins from the psychrophilic bacteria Desulfotalea...
-
Remarks on use of the term “deep eutectic solvent” in analytical chemistry
PublikacjaAbout 20 years ago, Abbott and co-workers researched new solvents that were based on mixtures of choline chloride with urea and carboxylic acids and that were liquid at ambient temperature. The term “deep eutectic solvent” (DES) was later adopted for similar mixtures. As DESs have a number of interesting features, they quickly attracted the attention of researchers and found application in various branches of chemical and materials...
-
Synthesis, structural characterization, and thermal properties of Ca‐ and La‐doped soda‐lime glasses by laser melting
PublikacjaLaser melting techniques have been used in the preparation of unconventional glass compositions with high melting temperatures. Thus, we wanted to test the feasibility of using a CO2 laser in the preparation of nitrogen-rich oxynitride glasses and nitride silicate glasses. Melting from oxides and metallic raw materials, we wanted to study first glass formation and possible evaporation losses of the glass components. Two glass series...
-
Characterization of single-stranded DNA-binding proteins from the psychrophilic bacteria
PublikacjaSingle-stranded DNA-binding proteins (SSBs) are indispensable elements in the cells of all living organisms. SSB proteins interact with ssDNA insequence in an independent manner, preventing them from forming secondary structures and from degradation by nucleases. In this way, SSB-binding proteins participate in all processes involving ssDNA, such as replication, repair and recombination. Although there are differences in amino...
-
Characterization of single-stranded DNA-binding proteins from the psychrophilic bacteria
PublikacjaSingle-stranded DNA-binding proteins (SSBs) are indispensable elements in the cells of all living organisms. SSB proteins interact with ssDNAinsequence in an independent manner, preventing them from forming secondary structures and from degradation by nucleases. In this way, SSB-binding proteins participate in all processes involving ssDNA, such as replication, repair and recombination.Although there are differences in amino acid...
-
Ionic liquids for nano- and microstructures preparation. Part 2: Application in synthesis
PublikacjaIonic liquids (ILs) are widely applied to prepare metal nanoparticles and 3D semiconductor microparticles. Generally, they serve as a structuring agent or reaction medium (solvent), however it was also demonstrated that ILs can also play a role of a co-solvent, metal precursor, reducing as well as surface modifying agent. The crucial role and possible types of interactions between ILs and growing particles have been presented in...
-
Study of the ability of TXT-compounds to promote telomeric G4 DNA thermal stabilization using FRET melting assay
Dane BadawczeThe data set contains a DNA melting screen obtained from the FRET melting assay. Thermal stabilities of G-quadruplex structures were analysed in the presence and in absence of ligands. TMPyP4 and MTX were used as references. Measurements were carried out in triplicate using a LightCycler 480 thermocycler (Roche Life Science) with a filter setting of...
-
Influence of laser melting on surface layer properties of titanium alloy Ti6Al4V
PublikacjaIn time of rapid technology and medicine progress, implants are becoming more widely used in the human body, ranging from dental implants, stabilizing plates, screws, orthopaedic prostheses. For example, there are many types of hip prostheses used for hip replacement as well as various types of materials used for these orthopaedic prostheses. Properties of titanium alloys used in hip prostheses combined with good strength properties,...
-
AFM imaging of surface of modern soldering alloy
Dane BadawczeFollowing the announcement in 2006 of European Union directives aimed at limiting the use of lead in electronic products, there was an urgent need to use lead-free solders in the electronics industry. Due to production requirements, it is necessary to use solders with different melting points. To replace the low-melting eutectic Sn 37 wt. Pb, the most...
-
Concentrations and loads of DOC, phenols and aldehydes in a proglacial arctic river in relation to hydro-meteorological conditions. A case study from the southern margin of the Bellsund Fjord – SW Spitsbergen
PublikacjaClimate warming accelerates the melting and thawing of cryosphere components. Therefore, it favours the release of contaminants stored in High-Arctic glaciers for many years. The rate of land-based glacier retreat is of particular importance for the hydrological regime of glacial rivers, but also for the chemical composition of their waters. In this study, we examined 84 surface water samples collected during a period of 42 days...
-
P92 steel and inconel 617 alloy welds joint produced using ERNiCr-3 filler with GTAW process: Solidification mechanism, microstructure, mechanical properties and residual stresses
PublikacjaThe objective of the current study was to analyse the microstructure, mechanical characteristics, and residual stresses of a dissimilar welded joint (DWJ) made of P92 steel and the Inconel alloy 617 (IN617) using the gas tungsten arc welding (GTAW) method. The ERNiCr-3 filler was selected to produce the conventional V groove (VG) and narrow V groove (NVG) butt joint. The filler deficient zones in the weldments, such as the filler...
-
Structure and thermoelectric properties of Cs-Bi-Te alloys fabricated by different routes of reduction of oxide reagents
PublikacjaCesium-bismuth-telluride polycrystalline materials were fabricated using a cost-effective method based on a reduction of oxide reagents, leading to a production of a material with good thermoelectric properties. Several samples with various initial stoichiometry were prepared by melting of oxide powders at 1050 °C, quenching, milling to powders and then reducing in pure hydrogen at 400 °C. Another concept was to obtain the CsBi4Te6...
-
Opracowanie zestawu diagnostycznego do genetycznego typowania szczepów bakteryjnych metodą PCR MP
PublikacjaOmówiono etapy tworzenia zestawu diagnostycznego przeznaczonego do genetycznego typowania szczepów bakteryjnych wykorzystującego procedurę PCR MP (PCR Melting Profiles). Dokonano optymalizacji warunków i walidacji metody w celu przystosowania jej do potrzeb epidemiologicznej oceny zakażeń szpitalnych. Opracowany zestaw stwarza możliwości zastosowania go w laboratoriach prowadzących rutynowo badania diagnostyczne.
-
Evolution of magnetic and transport properties in (Cr1−xMnx)2AlC MAX-phase synthesized by arc melting technique
PublikacjaHerein we initiate a comeback to the arc melting technique to produce MAX-phase solid solutions. Bulk samples of (Cr1−xMnx)2AlC MAX-phase with X = 0, 0.025, 0.05 and 0.1 were synthesized and studied by means of X-ray diffractometry, scanning electron microscopy in combination with energy-dispersive X-ray spectroscopy. Samples were established to be homogeneous with an incorporation of Cr7C3, AlCr2 and Al2O3 secondary phases which...
-
Nanotechnologies in Development of Structural Materials and Biomaterials
PublikacjaThe nanometric materials and technologies resulted in nanostructures are reviewed. The examples of nanomaterials are shown. The typical nanotechnologies, including plastic deformation, mechanical attrition, controlled detonation, hot plasma jet synthesis, laser vaporisation, CVD and PVD, mechanical milling, annealing, ultrasonic irradiation, nanolithography, electrocrystallisation, electrospinning, sol-gel method, cryogenic laser-enhanced...
-
Novel, Fully Biobased Semicrystalline Polyamides
PublikacjaNovel, semicrystalline polyamides and co(polyamides) were synthesized from biobased sebacic acid (SA), 2,5-diamino-2,5-dideoxy-1,4;3,6-dianhydroiditol (diaminoisoidide, DAII) as well as from 1,4-diaminobutane (DAB), also known as putrescine in nature. Low molecular weight polyamides were obtained by melt polycondensation of the salts based on these monomers or by interfacial polycondensation. In order to increase their molecular...
-
THE USE OF THE Ti-13Zr-13Nb ALLOY POWDER FOR MANUFACTURING OF PROSTHETIC PARTS BY SELECTIVE LASER MELTING
PublikacjaThe 3D printing is a manufacturing technique belonging to the additive methods able to prepare the designed parts for various purposes. The present reasearch was aimed to fabricate the prosthetic foundations and bridges made of the new Ti-13Zr-13Nb alloy by the selective laser melting (SLM) of a metal powder. The scanning electron examinations and micro scanning tomography were used to investigate the surface quality and intrinsic...
-
Selective Laser Melting of Ti Alloy for Manufacturing The Prosthetic Elements
PublikacjaThe selective laser melting (SLM) is the additive manufacturing method of custom-designed parts. The used materials and the applications are various, including medicine. The titanium and its alloys are materials for which the dimensional quality, surface smoothness and no or extremely low porosity are difficult to reach. In this paper, the successful attempt to obtain by SLM the individually designed prosthetic bridges is described....
-
Technika PCR MP (PCR Melting Profile) - możliwości zastosowania w badaniach epidemiologicznych
PublikacjaUżyteczność PCR MP (ang. PCR Melting Profile), stosunkowo nowej techniki różnicowania genetycznego szczepów mikroorganizmów, pokazano na przykładach badań epidemiologicznych, dotyczących wykrywania zakażeń szpitalnych, analizy sytuacji epidemiologicznej i identyfikacji transmisji bakteryjnej u poszczególnych pacjentów. Technikę PCR MP charakteryzuje prostota, niskie koszty wykonania oraz potencjał różnicujący porównywalny do metody...
-
Investigation of magnetic order in a new intermetallic compound Nd2PtGe3
PublikacjaIn the present study we report a successful synthesis of the new intermetallic compound Nd2PtGe3 by an arc-melting method. The powder X-ray diffraction analysis indicates that this compound crystallizes in an disordered variant of the AlB2-type structure (space group P6/mmm, no. 191) with lattice parameters a = 4.2455 Å and c = 4. 1933 Å. The compound exhibits a cluster-glass transition below Tf = 2.9 K, characterized through ac...
-
Niobate in silicate and phosphate glasses: Effect of glass basicity on crucible dissolution
PublikacjaUsing niobium crucibles for melting phosphate and silicate glasses of various modifier oxide contents, and therefore varying optical basicity (Λ), was found to result in varying dissolution rates of niobate during melting. Because of their high electronic polarizability, even small concentrations of niobates are detectable in the Raman spectra of glasses. Even less than 1 mol% Nb2O5 can be identified, as independently confirmed...
-
Determinants of the surface quality, density and dimensional correctness in selective laser melting of the Ti-13Zr-13Nb alloy
PublikacjaSelective laser melting is widely used for custom-designed elements. Successful manufacturing depends on laser treatment parameters and material features. This research aimed to determine the effects of laser power, scan time and hatch distance on surface quality, relative density and dimensional precision for cuboids made of the Ti-13Zr-13Nb alloy. The influence of energy density, energy flux and pre-heating was seen to be decisive...
-
Biocompatibility and bioactivity of load-bearing metallic implants
PublikacjaThe main objective of here presented research is to develop the titanium (Ti) alloy base composite materials possessing better biocompatibility, longer lifetime and bioactivity behaviour for load-bearing implants, e.g. hip joint and knee joint endoprosthesis. The development of such materials is performed through: modeling the material behaviour in biological environment in long time and developing of new procedures for such evaluation;...
-
Hydrophobic and hydrophilic properties of pollutants as a factor influencing their redistribution during snowpack melt
PublikacjaGlaciers accumulate organic pollutants delivered by snow. However, our understanding of the exact dynamics of organic pollutants in the snowpack relies primarily on laboratory experiments and mathematical models. To fill the gap related to the detailed field data, we have conducted observations of melting snow profiles in two locations and three different stages of melting on one High Arctic glacier, as well as in superimposed...
-
Two-step synthesis of niobium doped Na–Ca–(Mg)–P–Si–O glasses
PublikacjaNiobium doped biosolubility glasses in the Na–Ca–(Mg)–P–Si–O system were prepared by using an untypical two-step synthesis route. The parent glass was melted in air atmosphere at 1350 °C followed by re-melting the glass in Nb crucible with the addition of metallic Mg/Ca powder in the nitrogen atmosphere. The second melting step was carried out at 1450–1650 °C, using an induction furnace. The topography and structure of the obtained...
-
ESTIMATION OF YOUNG`S MODULUS OF THE POROUS TITANIUM ALLOY WITH THE USE OF FEM PACKAGE
PublikacjaPorous structures made of metal or biopolymers with a structure similar in shape and mechanical properties to human bone can easily be produced by stereolithographic techniques, e.g. selective laser melting (SLM). Numerical methods, like Finite Element Method (FEM) have great potential in testing new scaffold designs, according to their mechanical properties before manufacturing, i.e. strength or stiffness. An example of such designs...
-
3D Printing of Metallic Implants
PublikacjaThe fabrication of various elements, solid and open porous structures of stainless steel and Ti alloy is described. The process was started with the design of 3D models in CAD/CAM system. The 3D models were transformed into *.stl files and then the manufacturing process of the real structures by means of the selective laser melting with the SLM Realizer 100 3D printer was made. The paper shows the porous specimens made for possible...
-
Runoff Water
PublikacjaThis entry summarizes the current state of knowledge on the role of atmospheric pollutants' transport to the surface and transformations of wet deposition on contact with various surfaces. Runoff waters are one of the forms in which precipitation reaches the groundwater and surface water. They are formed when rain or melting snow washes the surfaces of roofs, highways, agricultural areas, or tree canopies. Pollutants present in...
-
The structure of lead-silicate glasses and nanocomposites doped with iron oxide
Dane BadawczeThe structure of iron-doped glasses and glass-ceramics were studied. Samples has the composition of 50SiO2–(50−x)PbO–xFe2O3, where x=15, 20 and 25 (in mol%). All samples were prepared by the conventional melt quenching technique; the melting was conducted in air at 1623 K in alumina crucibles. The melts were poured on a brass plate preheated to 573...
-
The morphology of lead-silicate glasses and nanocomposites doped with iron oxide
Dane BadawczeThe topography of iron-doped glasses and glass-ceramics were studied. Samples has the composition of 50SiO2–(50−x)PbO–xFe2O3, where x=15, 20 and 25 (in mol%). All sampleswere prepared by the conventional melt quenching technique; the melting was conducted in air at 1623 K in alumina crucibles. The melts were poured on a brass plate preheated to 573...
-
Orientation effects on the fracture behaviour of additively manufactured stainless steel 316L subjected to high cyclic fatigue
PublikacjaIn this paper, stainless steel 316L (SS316L) bars were additively manufactured (AM) in three orientations (Z – vertical, XY – horizontal, ZX45 – midway between vertical and horizontal) by using the Laser Powder Bed Fusion Melting (LPBF-M) method. The AM specimens were subjected to load control fatigue testing under full tension and compression (R = -1) at stress amplitudes ±350, ±400 and ±450 MPa. The XY and ZX45 printing orientations...
-
Bioactive quaternary ammonium ionic liquids.
PublikacjaAn ionic liquid (IL) is an organic compound that contains at least one ionic bond. It consists of an organic cation and an organic or inorganic anion. It is an organic salt having a melting point below 100C. A very interesting group of IL are those with a long chain quaternary ammonium cation. They are formed by direct synthesis or by an anion-exchange reaction in quaternary ammonium halides. Popular and cheap precursors for the...
-
Raman spectroscopy analysis of poly(lactic acid)-carbon black composite treated by femtosecond laser
Dane BadawczeThe dataset contains the Raman spectroscopy measurements of commercially available carbon black-filled poly(lactic acid) 3D printed electrodes after femtosecond laser ablation. These results were utilized in the manuscript published in Electrochimica Acta: 10.1016/j.electacta.2022.140288
-
The structure of lead-silicate glasses containing nanocrystallites of iron oxides
Dane BadawczeThe structure of iron-doped glasses and glass-ceramics were studied. Samples has the composition of (50 − 0.5x)SiO2–(50 − 0.5x)PbO–xFe2O3, where x = 2, 5, 10, 15, 20 and 25 (in mol%). All samples were prepared by the conventional melt quenching technique; the melting was conducted in air at 1623 K in alumina crucibles. The melts were poured on a brass...
-
The morphology of lead-silicate glasses containing nanocrystallites of iron oxides
Dane BadawczeThe topography of iron-doped glasses and glass-ceramics were studied. Samples has the composition of (50 − 0.5x)SiO2–(50 − 0.5x)PbO–xFe2O3, where x = 2, 5, 10, 15, 20 and 25 (in mol%). All sampleswere prepared by the conventional melt quenching technique; the melting was conducted in air at 1623 K in alumina crucibles. The melts were poured on a brass...
-
Characterization of structural, thermal and mechanical properties of bismuth silicate glasses
Publikacjahe influence of heating and reduction processes on the structural, thermal and mechanical properties of bismuth-silicate glasses has been investigated. Two compositions of glasses: 40Bi2O3–60SiO2 (Bi0.57Si0.43Ox) and 27Bi2O3–73SiO2 (Bi0.43Si0.57Ox) were fabricated by a typical melt quenching technique. Then the reduction in hydrogen at 380 °C for 20, 42 or 67 h was performed. It was found that a 50 μm-thick layer was formed on...
-
Application of 3D printing metal powder technology in the manufacture of components with complex geometries
PublikacjaThe possibilities of using 3D printing powder technologies for making objects with complex geometries were presented. For this purpose, selected examples of elements with different geometries were used, which were built using metal powder methods – DMLS (direct metal laser sintering) / SLM (selective laser melting). Simultaneously, the indicated elements concern those areas of industry where 3D printing technology has been widely...
-
New plasmonic platform for enhanced luminescence of Valrubicin
PublikacjaLuminescence enhanced by new structure of plasmonic platform with aluminum oxide (Al2O3) buffer layer deposited on gold nanostructures is investigated. Regularly distributed gold nanostructures of average dimension of 50 nm formed the active part of plasmonic platforms. They were manufactured on Corning 1737 glass substrate by melting of gold thin film. The nanostructures were coated by dielectric Al2O3 thin film with thickness...