Filtry
wszystkich: 1474
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: ELASTOMERIC POLYMER COMPOSITE
-
Towards Computer-Aided Graphene Covered TiO2-Cu/(CuxOy) Composite Design for the Purpose of Photoinduced Hydrogen Evolution
PublikacjaIn search a hydrogen source, we synthesized TiO2-Cu-graphene composite photocatalyst for hydrogen evolution. The catalyst is a new and unique material as it consists of copper-decorated TiO2 particles covered tightly in graphene and obtained in a fluidized bed reactor. Both, reduction of copper from Cu(CH3COO) at the surface of TiO2 particles and covering of TiO2-Cu in graphene thin layer by Chemical Vapour Deposition (CVD) were...
-
Impact response of novel layered two stage fibrous composite slabs with different support type
PublikacjaThe performance of novel Layered Two Stage Fibrous Composite slabs (LTSFC) was pioneered under falling mass collisions using a combined experimental and numerical study. Such LTSFC slabs consist of three layers with and without the insertion of glass fibre mesh between the layers. LTSFC techniques were used to fabricate the composite slabs with three layers including 3%, 1.5%, and 3% of fibre content for the top, middle, and...
-
Surface modifcation of PMMA polymer detected by XPS
Dane BadawczeIn order to obtain the experimental specimens, four PMMA/PC61BM samples with the following mass proportions were prepared: 10%, 20%, 30%, and 40%. In addition, as a reference, a PMMA sample without PC61BM was prepared as well. For the fabrication process, PC61BM 99.5% (Solenne BV), chloroform HPLC (Sigma Aldrich), and PMMA (commercially available...
-
A Quantitative Investigation of Dislocation Density in an Al Matrix Composite Produced by a Combination of Micro-/Macro-Rolling
PublikacjaAn aluminum matrix composite with dispersed carbon nanotubes (CNTs) was produced via flake powder metallurgy using a micro-rolling process and vacuum hot pressing (VHP), followed by conventional rolling using a macro-rolling process. The microstructure and mechanical properties of the produced composites were studied. In addition, a new quantitative model was introduced to study the dislocation density based on the microstructural...
-
Edgewise Compressive Behavior of Composite Structural Insulated Panels with Magnesium Oxide Board Facings
PublikacjaEdgewise compression response of a composite structural insulated panel (CSIP) with magnesium oxide board facings was investigated. The discussed CSIP is a novel multifunctional sandwich panel introduced to the housing industry as a part of the wall, floor, and roof assemblies. The study aims to propose a computational tool for reliable prediction of failure modes of CSIPs subjected to concentric and eccentric axial loads. An advanced...
-
Preventing of earthquake-induced pounding between steel structures by using polymer elements – experimental study
PublikacjaPounding between two, or more, adjacent buildings during earthquakes has been identified as one of the reasons for substantial damage or even total collapse of colliding structures, so it has been the subject of numerous studies in the recent years. A major reason leading to interactions between adjacent, insufficiently separated structures results from the differences in their dynamic properties. A number of different methods...
-
Low-strain sensor based on the flexible boron-doped diamond-polymer structures
PublikacjaA free-standing high boron-doped diamond nanosheet (BDDNS) has been fabricated for the development of a flexible BDDNS strain senor. High boron-doped diamond was initially grown on a tantalum substrate in a microwave plasma-assisted chemical vapor deposition method, and was then transferred to a Kapton polymer substrate to fabricate the flexible BDDNS/Kapton device. Before performing the transfer process, the thin BDDNS’s morphology...
-
Polymer journal bearings behaviour research under limited lubrication and cooling conditions conducted on high torque test rig
PublikacjaPolymer journal bearings are frequently used as a water-lubricated bearings of small marine units’ propeller shafts . Choice of these bearings is based on their simple construction and relatively low purchase and maintenance costs. Although properly designed and installed water lubricated bearings may well last for over a decade, rapid wear or failure of these bearings can be observed...
-
Magdalena Rucka prof. dr hab. inż.
Osoby -
By-Products from Food Industry as a Promising Alternative for the Conventional Fillers for Wood–Polymer Composites
PublikacjaThe present paper describes the application of two types of food-industry by-products, brewers’ spent grain (BSG), and coffee silverskin (ŁK) as promising alternatives for the conventional beech wood flour (WF) for wood–polymer composites. The main goal was to investigate the impact of partial and complete WF substitution by BSG and ŁK on the processing, structure, physicochemical, mechanical, and thermal properties of resulting...
-
Damage Detection of Steel-Concrete Composite Beam
Publikacja -
Wavelet analysis for damage identification in composite structures
Publikacjaw pracy zaproponowano metodę analizy sygnalu opartą o transformatę falkową, pozwalajacą na identyfikcaje pęknięcia zmęczeniowego w jednowymiarowych elementach konstrukcyjnych wykonanych z materialow kompozytowych
-
Tribological Behaviour of Copper-Graphene Composite Materials
Publikacja -
Detection of delamination in multi layer composite beams.
PublikacjaW pracy przedstawiono model belki kompozytowej z delaminacją. Omówiono czynniki propagacji fali sprężystej w belce i możliwości wykorzystania zmian w propagującej fali wywołanych delaminacją do jej detekcji.
-
Role of composite cathodes in single chamber SOFC.
PublikacjaZbadano wpływ składu katody na napięcie oraz wydajność ogniw paliwowych pracujących w konfiguracji jednokomorowej. W związku z tym, że takie ogniwo pracuje w mieszanienie powietrza i paliwa, napięcie jest określone przez różnice aktywności katalitycznej anody i katody. Typowy cermet na bazie niklu oraz związki perovskitów pracują dobrze odpowiednio jako anoda i katoda. Jednakże perowskity mają również właściwości katalityczne,...
-
Wave Propagation Modelling in Composite Plates with Damages
PublikacjaW pracy przedstawiono model i wyniki analizy propagacji fali spręzystej w płycie kompozytowej z uszkodzeniami.
-
Wavelet Analysis for Damage Identification in Composite Structures
Publikacja -
Fabrication methods of smart composite coatings - review
PublikacjaPostoperative bacterial infections are one of the main reasons for unsuccessful implantation of long-term implants. The development of bacterial infection requires antibiotic therapy, in extreme cases a reimplantation procedure is necessary. In order to provide materials for implants with antibacterial properties, they are subjected to modifications to create a coating that will release the drug substance, when the inflammation...
-
Failure Analysis of footbridge made of composite materials
PublikacjaFinite element method analysis of a pedestrian footbridge made of sandwich material is presented. The internal structure of the material is modelled as a structural shell assuming the Equivalent Single Layer approach (ESL). Two FEM commercial codes are employed. The response of the structure is studied in order to determine the load level that activates Hashin and Tsai-Wu failure criteria. Some practical aspects of designing footbridges...
-
Water Footprint Assessment of Selected Polymers, Polymer Blends, Composites, and Biocomposites for Industrial Application
PublikacjaThis paper presents a water footprint assessment of polymers, polymer blends, composites, and biocomposites based on a standardized EUR-pallet case study. The water footprint analysis is based on life cycle assessment (LCA). The study investigates six variants of EUR-pallet production depending on the materials used. The system boundary included the production of each material and the injection molding to obtain a standardized...
-
Thermal properties of a cement composite containing phase change materials (PCMs) with post-pyrolytic char obtained from spent tyres as a carrier
PublikacjaThis work examines the possible use of post-pyrolysis char made from spent vehicle tyres as a carrier for phase change materials (PCM), which could be used as an additive to cement mortar. Because of the ability of PCM to accumulate heat, the cement composite obtained from it, apart from its structural and strength properties, will acquire an additional energy storage function, which can be very important for energy-saving construction. In...
-
Experimental and numerical evaluation of mechanical behaviour of composite structural insulated wall panels under edgewise compression
PublikacjaA composite structural insulated sandwich panel (CSIP) is a quite novel approach to the idea of sandwich structures. A series of natural-scale experimental test is required each time a change in panel’s geometry is planned and a reliable computational tool is required to precede actual laboratory testing with virtual simulations. An attempt of creating such a tool has been made with use of a commercial FEM code ABAQUS, in order...
-
Insights into the Thermo-Mechanical Treatment of Brewers’ Spent Grain as a Potential Filler for Polymer Composites
PublikacjaThis paper investigated the impact of twin-screw extrusion parameters on the properties of brewers’ spent grain. The chemical structure, antioxidant activity, particle size, and color properties, as well as the emission of volatile organic compounds during extrusion, were investigated. The main compounds detected in the air during modifications were terpenes and terpenoids, such as α-pinene, camphene, 3-carene, limonene, or terpinene....
-
Characterization of various drinking waters by new potentiometric taste sensor with lipid, lipid-like polymer membranes
PublikacjaA new sensing system comprising five all-solid-state electrodes with lipid, lipid like-polymer membranes was applied for rapid qualitative and quantitative analysis of various drinking waters. The results elaborated by chemometric methods revealed sensitivity to CO2 content in drinking water, suggesting that this sensing system could be used as a taste sensor. The ability of taste sensor to perform quantitative analysis of minerals...
-
Ni/cerium Molybdenum Oxide Hydrate Microflakes Composite Coatings Electrodeposited from Choline Chloride: Ethylene Glycol Deep Eutectic Solvent
PublikacjaCerium molybdenum oxide hydrate microflakes are codeposited with nickel from a deep eutectic solvent-based bath. During seven days of exposure in 0.05 M NaCl solution, the corrosion resistance of composite coating (Ni/CeMoOxide) is slightly reduced, due to the existence of some microcracks caused by large microflakes. Multielemental analysis of the solution, in which coatings are exposed and the qualitative changes in the surface...
-
Layer-by-layer polymer deposited fabrics with superior flame retardancy and electrical conductivity
PublikacjaSmart and multifunctional textiles and fabrics are progressively developing, such that multifunctional fabrics are becoming more widespread. We elaborated herein multi-layered flax fabrics with superior flame retardancy and conductivity, which revealed fireproof feature while keeping conductivity during burning. The flax fabric was reinforced by layer-by-layer (LbL) deposition of sodium polyacrylate (SPA), polyethylenimine (PEI),...
-
Deformation Analysis of a Composite Bridge during Proof Loading Using Point Cloud Processing
PublikacjaRemote sensing in structural diagnostics has recently been gaining attention. These techniques allow the creation of three-dimensional projections of the measured objects, and are relatively easy to use. One of the most popular branches of remote sensing is terrestrial laser scanning. Laser scanners are fast and efficient, gathering up to one million points per second. However, the weakness of terrestrial laser scanning is the...
-
Electrical properties of polymer coatings modified with nanoadditives
PublikacjaW pracy przedstawiono właściwości elektryczne (antystatyczne, rezystancję powierzchniową) polimerowych powłok. Pokazano wpływ różnych domieszek na czasy rozładowania się warstwy oraz na jej rezystancję powierzchniową.
-
Manufacturing of metal-polymer composites for medical applications
Publikacja -
Conducting Polymer Microelectrodes Anchored to Hydrogel Films
PublikacjaArtykuł prezentuje wytwarzanie organicznych hydrożeli z mikroelektrodami poli(3,4-ethylenedioxythiophene, PEDOT), które wykazują obniżoną rezystywność 100 Ω/□. Proces przygotowania rozpoczyna się elektroosadzania przewodzącego PEDOT (ok. 20 S/cm) na mikroelektrodach Pt. Elektrolityczne wiąże się film PEDOT z hydrożelem. Tak wytworzona struktura jest odrywana elektrycznie pd podłoża.
-
Mechanism for sonocoating a polymer surface with nano-hydroxyapatite
Publikacja -
THERMOPLASTIC POLYMER MACHINE GUARDS – EXPLOITATION SAFETY
Publikacja -
Raman investigation of hybrid polymer thin films
PublikacjaPrzestawiono problemy diagnostyki ramanowskiej transparentnych struktur cienkowarstwowych wykonanych metodą zol-żel z polimerów hybrydowych. Analizowano możliwości badania struktury molekularnej i grubości, a także określania jakości wykonania struktur falowodowych. Przedstawiono wyniki badań wykonanych mikroskopem ramanowskim dla polimerowych struktur cienkowarstwowych osadzonych na podłożach szklanych i krzemowych.
-
Investigations of a new humidity sensor with polymer film
PublikacjaPrzedstawiono wyniki badań impedancyjnych nowego czujnika wilgotności z filmem polimerowym. Jako polimer wykorzystano chemicznie modyfikowaną polietylenoiminę.
-
Green Polymer Nanocomposites for Skin Tissue Engineering
PublikacjaFabrication of an appropriate skin scaffold needs to meet several standards related to the mechanical and biological properties. Fully natural/green scaffolds with acceptable biodegradability, biocompatibility, and physiological properties quite often suffer from poor mechanical properties. Therefore, for appropriate skin tissue engineering and to mimic the real functions, we need to use synthetic polymers and/or additives as complements...
-
Recycled rubber wastes-based polymer composites with flame retardancy and electrical conductivity: Rational design, modeling and optimization
PublikacjaPolymer recycling techniques experience a maturity period of design and application. Rubbers comprise a high proportion of polymer wastes, highly flammable and impossible to re-melt. Polymer composites based on ground tire rubber (GTR) and ethylene-vinyl acetate copolymer (EVA) containing carbon black (CB) (1–50 phr), with variable EVA/GTR weight composition (10/90, 25/75, 50/50, 75/25 and 90/10), and processing temperature (Low:...
-
Facilitated water transport in composite reduced graphene oxide pervaporation membranes for ethanol upgrading
PublikacjaHigh purity ethanol is one of the most sought-after renewable energy sources. However, standard production methods yield ethanol of insufficient quality. Membrane processes such as pervaporation are recognized as a viable method for upgrading ethanol. Their performance and selectivity depend solely on membrane employed. Hydrophilic polyvinyl alcohol (PVA) membranes are used industrially for this purpose, but there is a trade-off...
-
Marta Kuc-Czarnecka dr
OsobyMarta Kuc-Czarnecka jest zastępczynią kierownika Katedry Statystyki i Ekonomii na Wydziale Zarządzania i Ekonomii Politechniki Gdańskiej. Pełni również funkcję pełnomocniczki Dziekana ds. akredytacji AMBA. Jest współzałożycielką Rethinking Economics Gdańsk oraz członkinią Fundacji im. Edwarda Lipińskiego na rzecz promocji pluralizmu w naukach ekonomicznych. W latach 2018-2022 była ekspertką Europejskiej Fundacji na Rzecz Poprawy...
-
Thermosensitive composite based on agarose and chitosan saturated with carbon dioxide. Preliminary study of requirements for production of new CSAG bioink.
PublikacjaThis study introduces a method for producing printable, thermosensitive bioink formulated from agarose (AG) and carbon dioxide-saturated chitosan (CS) hydrogels. The research identified medium molecular weight chitosan as optimal for bioink production, with a preferred chitosan hydrogel content of 40–60 %. Rheological analysis reveals the bioink's pseudoplastic behavior and a sol-gel phase transition between 27.0 and 31.5 °C. The...
-
ADVANCES IN POLYMER TECHNOLOGY
Czasopisma -
Composite Hodgkin and non-Hodgkin lymphoma - Male, 65 - Tissue image [10100730045401421]
Dane BadawczeThis is the histopathological image of HEMATOPOIETIC AND RETICULOENDOTHELIAL SYSTEMS tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
Composite Hodgkin and non-Hodgkin lymphoma - Male, 65 - Tissue image [10100730045404301]
Dane BadawczeThis is the histopathological image of HEMATOPOIETIC AND RETICULOENDOTHELIAL SYSTEMS tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
Composite Hodgkin and non-Hodgkin lymphoma - Male, 65 - Tissue image [10100730045406631]
Dane BadawczeThis is the histopathological image of HEMATOPOIETIC AND RETICULOENDOTHELIAL SYSTEMS tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
Composite Hodgkin and non-Hodgkin lymphoma - Male, 65 - Tissue image [10100730045401001]
Dane BadawczeThis is the histopathological image of HEMATOPOIETIC AND RETICULOENDOTHELIAL SYSTEMS tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
Composite Hodgkin and non-Hodgkin lymphoma - Male, 65 - Tissue image [10100730045409611]
Dane BadawczeThis is the histopathological image of HEMATOPOIETIC AND RETICULOENDOTHELIAL SYSTEMS tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
Composite Hodgkin and non-Hodgkin lymphoma - Male, 65 - Tissue image [10100730045407111]
Dane BadawczeThis is the histopathological image of HEMATOPOIETIC AND RETICULOENDOTHELIAL SYSTEMS tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
Composite Hodgkin and non-Hodgkin lymphoma - Male, 65 - Tissue image [10100730045403771]
Dane BadawczeThis is the histopathological image of HEMATOPOIETIC AND RETICULOENDOTHELIAL SYSTEMS tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
Composite Hodgkin and non-Hodgkin lymphoma - Male, 65 - Tissue image [10100730045403501]
Dane BadawczeThis is the histopathological image of HEMATOPOIETIC AND RETICULOENDOTHELIAL SYSTEMS tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
A facile approach to fabricate load-bearing porous polymer scaffolds for bone tissue engineering
PublikacjaBiodegradable porous scaffolds with oriented interconnected pores and high mechanical are load-bearing biomaterials for bone tissue engineering. Herein, we report a simple, non-toxic, and cost-effective method to fabricate high-strength porous biodegradable scaffolds, composed of a polymer matrix of polycaprolactone (PCL) and water-soluble poly (ethylene oxide) (PEO) as a sacrificial material by integrating annealing treatment,...
-
Electrophoretically Deposited Chitosan/Eudragit E 100/AgNPs Composite Coatings on Titanium Substrate as a Silver Release System
PublikacjaDue to the possibility of bacterial infections occurring around peri-implant tissues, it is necessary to provide implant coatings that release antibacterial substances. The scientific goal of this paper was to produce by electrophoretic deposition (EPD) a smart, chitosan/Eudragit E 100/silver nanoparticles (chit/EE100/AgNPs) composite coating on the surface of titanium grade 2 using different deposition parameters, such as the...