Wyszukiwarka
Wyniki wyszukiwania dla: CO-GRINDING METHOD
-
Modeling and Simulation Method of Precision Grinding Processes
Publikacja -
Identification and characterization of the grinding burns by eddy current method
Publikacja -
The effect of tyre rubber grinding method on the rubber-asphalt binder properties
PublikacjaRubber products, especially those used in the automotive industry, are responsible for a significant amount of waste, mainly in the form of worn tyres. One way to recycle tyres is to use them as an asphalt binder modifier. The properties of rubber-asphalt binders vary greatly depending on the morphology of the ground tyre rubber (GTR) grains and the type of tyre to be recycled (car/truck). The paper presents the results of research...
-
Method of Monitoring of the Grinding Process with Lapping Kinematics Using Audible Sound Analysis
PublikacjaUtilising microphones as audible sound sensors for monitoring a single-side grinding process with lapping kinematics is presented in the paper. The audible sound generated during grinding depended on the cutting properties of electroplated tools with D107 diamond grains and different thicknesses of the nickel bond. The tool wear affected the obtained technological effects such as material removal rate and the surface roughness...
-
Utility of an unitary-shredding method to evaluate the conditions and selection of constructional features during grinding
Publikacja -
The influence of transition metals (Fe, Co) on the structural, magnetic and optical properties of TiO2 nanoparticles synthesized by the hydrothermal method
Publikacja -
Investigation of cationic distribution, Y–K angles, and optical and dielectric properties of as-synthesized cerium-doped cobalt nano-ferrites prepared by co-precipitation method
Publikacja -
Finger Vein Presentation Attack Detection Method Using a Hybridized Gray-Level Co-Occurrence Matrix Feature with Light-Gradient Boosting Machine Model
PublikacjaPresentation Attack Detection (PAD) is crucial in biometric finger vein recognition. The susceptibility of these systems to forged finger vein images is a significant challenge. Existing approaches to mitigate presentation attacks have computational complexity limitations and limited data availability. This study proposed a novel method for identifying presentation attacks in finger vein biometric systems. We have used optimal...
-
Correction to: Investigation of cationic distribution, Y–K angles, and optical and dielectric properties of as-synthesized cerium-doped cobalt nano-ferrites prepared by co-precipitation method
Publikacja -
The XRD diffraction patterns of as-prepared (La0.3Sr0.6Ce0.1)0.9Me0.1Ti0.9O3-δ (Me= Co, Cu, Fe, Mn, Ni) materials synthesized via the solid state reaction method
Dane BadawczeThe (La0.3Sr0.6Ce0.1)0.9Me0.1Ti0.9O3-δ (Me= Co, Cu, Fe, Mn, Ni) materials were synthesized via the solid state reaction method and examined as a potential anode material. First, the mixed oxide reagents were pressed into pellets and calcined at 1200 °C for 12 hours to decompose most of the organic compounds. The resulting calcined pellet was ground...
-
Monitoring of single-side lap grinding with electroplated tools
PublikacjaThe results presented in the paper show that utilising microphones as audible sound sensors is a suitable approach for monitoring a single-side lap grinding process due to the low levels of noise generated by the drives of a machine tool. The results confirm that sound signal analysis is a feasible and relatively simple method to monitor a lap grinding process with the use of an audible sound sensor. Proposed method can be used...
-
Thermal and technological aspects of double face grinding of Al2O3 ceramic materials
PublikacjaDouble face grinding with planetary kinematics is a process to manufacture workpieces with plan parallel functional surfaces, such as bearing rings or sealing shims. In order to increase the economic efficiency of this process, it has to be advanced permanently. The temperature in the contact zone of most grinding processes has a huge influence on the process efficiency and the workpiece qualities. In contrast to most grinding...
-
Thermal and technological aspects of double face grinding of C45 carbon steel
PublikacjaIn grinding, the contact zone temperature is a decisive factor influencing the achievable surface quality and the grinding tool wear. In contrast to other grinding processes, only few information regarding double face grinding with planetary kinematics when processing steel is known up to date. Since the successive substitution of in-dustrial double-sided lapping processes by double-sided grinding, it has become necessary to the...
-
Analysis of Roughness, the Material Removal Rate, and the Acoustic Emission Signal Obtained in Flat Grinding Processes
PublikacjaIn this work, the analysis of the acoustic emission (AE) signal in grinding processes is addressed. The proposed analysis method decomposes the acoustic signal into three frequency ranges. The total energy of each range is determined, as well as the highest frequency. Different grinding experiments were carried out, according to a full factorial design of experiments (DOE), in which feed speed, depth of cut, and transversal step...
-
The Impact of Material Selection on Durability of Exhaust Valve Faces of a Ship Engine – A Case Study
Publikacjawo alloys were used in order to extend the service life of marine engine exhaust valve head. Layers of cobalt base alloys were made of the powders with with chemical composition as follow: the layer marked L12; C-1,55%; Si-1,21%; Cr-29,7%; W-9%; Ni-2%; Mo<0,01%; Fe-1,7%; Co-54,83% and the layer marked N; C-1,45%; Co-38,9%; Cr-24,13%; Ni-10,43%; W-8,75%; Fe-7,64%; Mo-7,56%; Si-2,59%. Base metal was valve steel after heat treatment....
-
Mariusz Deja prof. dr hab. inż.
OsobyAdiunkt w Katedrze Technologii Maszyn i Automatyzacji Produkcji. Ukończył w 1993 roku studia wyższe magisterskie na Wydziale Mechanicznym Politechniki Gdańskiej, kierunek: Mechanika i Budowa Maszyn, specjalność: Projektowanie Procesów Technologicznych. Po ukończeniu studiów podjął pracę w Katedrze Technologii Maszyn i Automatyzacji Produkcji, a jego podstawowy obszar działalności naukowej związany był z technologią docierania...
-
Microgrinding with single-disk lapping kinematics.
PublikacjaGrinding operations are carried out with a variety of tool-workpiece configurations. The selection of a grinding process for a particular application depends on part shape, part size, ease of fixture, requirements concerning the acceptable shape errors. It is evident that lapping is very effective in eliminating the waviness while surface grinding is not. Dual disk machines for the double face grinding with planetary kinematics...
-
Sphere Drive and Control System for Haptic Interaction With Physical, Virtual, and Augmented Reality
PublikacjaA system for haptic interaction with physical, virtual, and augmented realities, founded on drive and measurement elements (DMEs), is considered. The system consists of eight DME rolls equipped with linear actuators, able to measure their angular velocity, drive the sphere, and adjust downforce (pressing the roll against the sphere). Two modeling issues are addressed. Special effort is put in to compensate for various technical...
-
Mirosław Wołoszyn dr hab. inż.
OsobyUrodził się 18 marca 1963 r. w Gdyni. Absolwent Wydziału Elektrycznego Politechniki Gdańskiej. Od 1987 r. pracuje na Wydziale Elektrotechniki i Automatyki Politechniki Gdańskiej. W roku 1997 uzyskał stopień doktora nauk technicznych, a w roku 2013 – stopień doktora habilitowanego. Aktualnie zatrudniony na stanowisku profesora nadzwyczajnego. Jego zainteresowania badawcze dotyczą lokalizacji i identyfikacji obiektów ferromagnetycznych...
-
Reduction of noise and rolling resistance by horizontal grinding of asphalt pavements
PublikacjaGrinding of cement concrete pavements to reduce unevenness and noise is common since a long time. Grinding is then made with wheels equipped with diamond blades rotating in the vertical plane. This creates narrow vertical/longitudinal grooves in the pavement. It is not applied to asphalt pavements. In this paper an alternative type of grinding is studied. In this case plates with diamond heads rotate in the same plane as the pavement,...
-
Studies on the influence of technological variants of finishing machining on flow of parts in flexible manufacturing
PublikacjaIn the article below the problems of influence of variants of finishing processing on flow of machining parts in flexible manufacturing system were presented. The investigations were carried out the technological processes for piston rods and rams of hydraulic cylinders. There were also presented model variants of technological processes for piston rods finished with the burnishing. In these studies the influence of technological...
-
The best porous asphalt pavement in Sweden so far
PublikacjaIn 2010 a double-layer porous asphalt concrete (DPAC) pavement was constructed in various versions on the E4 motorway through the Swedish city Huskvarna. As a result of a court decision the Swedish Transport Administration had to reduce noise emission by applying a low noise road surface that would reduce A-weighted noise levels by 5 dB, as an average. Earlier experience in Sweden indicated that it was possible to obtain a high...
-
Photocatalytic and Antimicrobial Properties of Ag2O/TiO2 Heterojunction
PublikacjaAg2O/TiO2 heterojunctions were prepared by a simple method, i.e., the grinding of argentous oxide with six different titania photocatalysts. The physicochemical properties of the obtained photocatalysts were characterized by diffuse-reflectance spectroscopy (DRS), X-ray powder diffraction (XRD) and scanning transmission electron microscopy (STEM) with an energy dispersive X-ray spectroscopy (EDS). The photocatalytic activity was...
-
Acoustic lifecycle study of the double-layer porous asphalt on E4 in Huskvarna, Sweden
PublikacjaIn 2010 a double-layer porous asphalt concrete (DPAC) pavement was constructed on the E4 motorway through the Swedish city Huskvarna. Earlier experience in Sweden indicated that it was feasible to obtain a high initial noise reduction but due to the widespread use of studded tires in winter, clogging and ravelling created losses of around 2 dB per year, with an expected acoustical lifetime of only 3 years. However, the improved...
-
Ground tire rubber functionalization as a promising approach for the production of sustainable adsorbents of environmental pollutants
PublikacjaWaste tires management and further utilization are currently one of the biggest concerns regarding the environment and human health protection. At present, shredding, grinding, or pulverization of waste tires are the most popular options for industrial recycling. Although many solutions for ground tire rubber (GTR) applications were checked and verified so far, their further implementation at an industrial scale is still very limited....
-
The Influence of Workpiece Hardness on Plate Temperature during One Side Lapping
PublikacjaLapping leads to a surface with low roughness and high precision. Because of required parts accuracy tool flatness is the key to the successful machining. To avoid its excessive thermal expansion, plate temperature research was taken. The goal was to determine the correlation between the basic lapping conditions and wheel temperature. In work Bulsara et al. authors developed model to estimate the maximum and average temperature...
-
The use of Preston equation to determine material removal during lap-grinding with electroplated CBN tools
PublikacjaGrinding executed in a lapping configuration is an alternative finishing process benefiting from both grinding and free-abrasive machining, while minimizing the heat effect impact. Electroplated tools can be effectively used in different abrasive processes, including high-speed grinding, however, the assessment of machining performance over time is a key factor in their correct use to achieve satisfactory technological results....
-
The Influence of the Depth of Cut in Single-Pass Grinding on the Microstructure and Properties of the C45 Steel Surface Layer
PublikacjaThe paper contains the results of a metallographic examination and nanoindentation test conducted for the medium carbon structural steel with low content of Mn, Si, Cu, Cr, and Ni after its grinding to a depth ranging from 2 μm to 20 μm, at constant cutting speed (peripheral speed) of vs = 25 ms−1 and constant feed rate of vft = 1 m/min. Applied grinding parameters did not cause the surface layer hardening, which could generate...
-
Vertical vibration reduction and audible sound analysis in surface grinding with electroplated tools
PublikacjaOne of the first approaches to the development of a grinding process monitoring system based on audible sound sensors is presented in the paper. Electroplated diamond tools (abrasive D64 and D107) were used in a modified single-disc lapping machine configuration for flat grinding of ceramics (Al2O3). The main aim of the machine modification was to reduce the vertical vibration in order to decrease the tool wear and to increase...
-
Research on Tool Temperature Dependence on Lapping Grains Size
PublikacjaCommonly used as a finishing operation, lapping has been used for achieving ultra-high finishes and close tolerances between mating pieces. Its carried out by applying loose abrasive grains between work and lap surfaces, and causing a relative motion between them resulting in a finish of multi-directional lay. The grains activity (sliding and rolling) in the working gap causes not only the material removal but also the temperature...
-
Cement kiln dust
PublikacjaThe volume of cement production in the world has remained at the level of approxi mately 4.1 billion tons/year. The cement production process is energy intensive and is the world’s leading emitter of carbon dioxide. Therefore, the main activities cement plants are aimed at introducing technologies changes in production of clinkier.The construction industry is responsible for the majority of CO2 emissions to the atmosphere: the...
-
Emilia Miszewska dr inż.
OsobyEmilia Miszewska urodziła się w 1986 roku w Gdańsku. Ukończyła Szkołę Podstawową nr 17 w Gdańsku z klasami sportowymi o profilu pływanie oraz Liceum Sportowe nr 11 im. Janusza Kusocińskiego w Gdańsku. W 2005 roku rozpoczęła jednolite studia magisterskie na Wydziale Inżynierii Lądowej i Środowiska, które ukończyła w roku 2011, broniąc pracę dyplomową pt. „Analiza i opracowanie wytycznych zabezpieczenia pożarowego oraz planu...
-
Developments in manufacturing engineering and machining process planning
PublikacjaCurrent research conducted in the Department of Manufacturing Engineering and Automation is presented in the paper. This includes: abrasive cutting off, grinding with lapping kinematics, rapid prototyping and machining procrss planning. Experimental results and computer simulation are presented and analysed.
-
Karol Daliga dr inż.
OsobyW 2005 roku ukończył klasę o profilu matematyczno - fizycznym i zdał maturę w I Liceum Ogólnokształcącym im. Władysława Gebika d. polskie gimnazjum w Kwidzynie. W latach 2005-2010 odbył studia magisterskie na Wydziale Fizyki Technicznej i Matematyki Stosowanej Politechniki Gdanskiej, a w latach 2008 - 2012 odbył studia inżynierskie na Wydziale Inżynierii Lądowej i Środowiska Politechniki Gdańskiej. 31 marca 2021 r. obronił pracę...
-
Krzysztof Nyka dr hab. inż.
OsobyKrzysztof Nyka, absolwent Wydziału Elektroniki Telekomunikacji i Informatyki Politechniki Gdańskiej (WETI PG), gdzie uzyskał tytuł magistra inżyniera (1986, telekomunikacja) stopień doktora nauk technicznych (2002, elektronika) i doktora habilitowanego (2020 automatyka, elektronika i elektrotechnika). Obecnie jest zatrudniony na stanowisku profesora uczelni w Katedrze Inżynierii Mikrofalowej i Antenowej WETI PG. Zainteresowania...
-
Recycling of Polyurethanes
PublikacjaPolyurethane waste can be recycled by mechanical methods (i.e., grinding and applying as a filler or pressing with a bonding agent) and chemical methods (mainly by e.g., glycolysis, hydrolysis, or aminolysis). There is also possibility to the recover energy from polyurethanes waste (by incineration, gasification, and pyrolysis).
-
Wear of electroplated diamond tools in lap-grinding of Al2O3 ceramic materials
PublikacjaCurrent development of modern products, together with ever-increasing demands for their operation and usage, necessitate the search for new processing methods. Abrasive machining is widely used in many industrial areas, especially for processing difficult-to-machine materials such as advanced ceramics. Grinding with lapping kinematics, also called lap-grinding, is still one of the innovative methods of abrasive processing being...
-
Petrophysical analyses of rock construction materials from the Roman rural settlement in Podšilo bay on Rab island (NE Adriatic, Croatia)
PublikacjaThis article presents the results of petrophysical analyses of limestones and sandstones used for the construction of the wall structures of a Roman rural settlement located in Podšilo Bay on Rab Island (Croatia). An on-site analysis of the walls indicated the use of different lithotypes, which is an uncommon case in the area. So far, no petrophysical properties of the applied materials have been tested, and their provenance...
-
Studies on the solid-liquid equilibria and intermolecular interactions Urea binary mixtures with Sulfanilamide and Sulfacetamide
PublikacjaThe binary phase diagrams of Sulfanilamide-Urea (SN-U) and Sulfacetamide-Urea (SC-U) were measured using differential scanning calorimetry technique (DSC). Both examined mixtures were found to form simple binary eutectics. The limited miscibility in the solid state observed by DSC, proving inability of co-crystallization in new multi-molecular form, was also confirmed using PXRD and FTIR-ATR measurements of solid dispersions...
-
Results after grinding C45 steel
Dane BadawczeThe database contains results from nanoindenter, scanning microscope and also X-ray diffractometer. To determine the residual stresses and the size of the crystallites in the ferrite grains in the grinded surface layer, the Williamson Hall analysis of the X-ray diffraction patterns was performed. XRD diffraction patterns were also used to perform a...
-
Marek Zienkiewicz dr inż.
OsobyDoktor inżynier Marek Hubert dwojga imion Zienkiewicz jest absolwentem Wydziału Geodezji, Inżynierii Przestrzennej i Budownictwa Uniwersytetu Warmińsko-Mazurskiego w Olsztynie. Zainteresowania naukowe w okresie studiów inżynierskich, magisterskich i doktoranckich rozwijał pod opieką przedstawicieli olsztyńskiej szkoły geodezyjnego rachunku wyrównawczego. W roku 2011 uzyskał tytuł zawodowy magistra inżyniera w zakresie geodezji...
-
Kazimierz Darowicki prof. dr hab. inż.
OsobyStudia wyższe ukończyłem w czerwcu 1981 roku po zdaniu egzaminu dyplomowego i obronie pracy magisterskiej. Opiekunem pracy magisterskiej był dr hab. inż. Tadeusz Szauer. W roku 1991, 27 listopada uzyskałem stopień naukowy broniąc pracę doktorską zatytułowaną „Symulacyjna i korelacyjna analiza widm immitancyjnych inhibitowanej reakcji elektrodowej”. Promotorem pracy był prof. dr hab. inż. Józef Kubicki (Wydział Chemiczny...
-
Jakub Miler dr inż.
OsobyKariera akademicka: 2000: mgr inż. Wydział ETI, Politechnika Gdańska, praca pt. "Computer system for supporting risk management in a software engineering project", promotor prof. Janusz Górski 2005: dr inż. Wydział ETI, Politechnika Gdańska, rozprawa pt. "A Method of Software Project Risk Identification and Analysis", obroniona z wyróżnieniem, dziedzina nauki techniczne, dyscyplina informatyka, promotor prof. Janusz Górski Zainteresowania...
-
Influence of Flat Lapping Kinematics on Machinability of Ceramics
PublikacjaNew tools for flat grinding of ceramics are presented in the paper. Electroplated CBN tools (B64 and B107) were used in a modified single-disc lapping machine configuration. The results from experiments, such as the material removal rate and surface roughness parameters are presented and analyzed. Numerical simulations, based on the model for the shape error and tool wear estimation in machining with flat lapping kinematics, are...
-
Joanna Janczewska prof. dr hab.
OsobyJoanna Janczewska odbyła studia wyższe magisterskie na kierunku Matematyka w latach 1994–1999 z wynikiem bardzo dobrym i uzyskała w 1999 roku tytuł magistra. W 2002 roku na Uniwersytecie Gdańskim uzyskała stopień naukowy doktora nauk matematycznych w zakresie matematyki. Promotorem w przewodzie doktorskim był dr hab. Andrzej Borysowicz, prof. UG. W październiku 2004 roku podjęła pracę na stanowisku adiunkta w Katedrze Algebry...
-
Paweł Szymon Dąbrowski dr inż.
OsobyDr inż. Paweł Szymon Dąbrowski w latach 2004-2009 studiował na kierunku geodezja i kartografia na Uniwersytecie Warmińsko-Mazurskim w Olsztynie, gdzie uzyskał tytuł zawodowy magistra inżyniera. W latach 2009-2016 pracował w wykonawstwie geodezyjnym w Iławie i Gdańsku. Doświadczenie zawodowe zdobył on podczas realizacji inwestycji Pomorskiej Kolei Metropolitalnej, co pomogło mu w zdobyciu w 2015 r. geodezyjnych uprawnień zawodowych...
-
THE MELT FLOWABILITY AND TENSILE PERFORMANCE OF POLY (-CAPROLACTONE)/BREWERS’ SPENT GRAIN COMPOSITES AS A FUNCTION OF FILLER MODIFICATION
PublikacjaNowadays, it is essential to reduce the environmental impact of products and technologies. Such an approach should be highlighted in all research activities. In the case of polymer composites, it can be realized by introducing by-products or waste materials as fillers. An auspicious example of such material is the brewers’ spent grain, the major byproduct of the beer production. Its chemical composition, relatively similar to conventional...
-
The influence of rubber recyclate morphology on the properties of rubber-asphalt composite
PublikacjaIn the paper wastes, mostly in the form of used tires, were analyzed. One of the methods of waste tires application use them as a modifier of asphalt. However, the properties of rubber-asphalt composites depend on the morphology of waste tiregranulate and kind of tire recycled (car/truck). In this chapter, the influence of grinding methods of waste tire on the prop¬erties of rubber-asphalt composites were studied. SEM analysis...
-
Enzymatic activities behind degradation of glucosinolates
PublikacjaMyrosinase (thioglucosidase, EC 3.2.1.147) is the enzyme responsible for the hydrolysis of glucosinolates (GLs). In plant tissue, myrosinase and GLs are sequestered in separate cellular compartments. As a result of cell disruption, e.g., after pathogen attack or on chopping or grinding during food preparation, the myrosinase comes into contact with GLs and catalyzes the hydrolysis of thioglucosidic bond in GL structure. Consequently,...
-
Convenient and efficient N-methylation of secondary amines under solvent-free ball milling conditions
PublikacjaIn the present work, we report the development of a rapid, efcient, and solvent-free procedure for the N-methylation of secondary amines under mechanochemical conditions. After optimization of the milling parameters, a vibrational ball mill was used to synthesize 26 tertiary N-methylated amine derivatives in a short time of 20 min (30 Hz frequency) and high yields ranging from 78 to 95%. An exception was compounds having a hydroxyl...