Filtry
wszystkich: 1253
wybranych: 656
Wyniki wyszukiwania dla: atypical antipsychotic
-
Structure redetermination, transport and thermal properties of the YNi3Al9 compound
PublikacjaSingle crystals of completely ordered variant of the YNi3Al9 compound were grown by self-flux method with excess of aluminum. The crystal structure of the title compound was redetermined from single crystal X-ray diffraction data. The structure adopts ErNi3Al9 type, space group R32, parameters of the unit cell a = 7.2838(2) Å, c = 27.4004(8) Å. The growth of relatively large single crystals of the YNi3Al9 compound, having completely...
-
Simulations of freshwater lens recharge and salt/freshwater interfaces using the HYDRUS and SWI2 packages for MODFLOW
PublikacjaThe paper presents an evaluation of the combined use of the HYDRUS and SWI2 packages for MODFLOW as a potential tool for modeling recharge in coastal aquife rs subject to saltwater intrusion. The HYDRUS package for MODFLOW solves numerically the one-dimensional form of the Richards equation describing water flow in variably- saturated media. The code computes groundwater recharge to or...
-
Analysis of pavement structure sensitivity to passage of oversized heavy duty vehicle in terms of bearing capacity
PublikacjaOversized heavy duty vehicles occur in traffic very rarely but they reach extremely high weights, even up to 800 tonne. The detrimental impact of these vehicles on pavement structure is much higher than in case of commercial vehicles that comprise typical traffic, thus it is necessary to assess the sensitivity of pavement structure to passage of oversized vehicles. The paper presents results of sample calculations of load equivalency factor...
-
Time window based features extraction from temperature modulated gas sensors for prediction of ammonia concentration
PublikacjaElectronic gas recognition systems, in literature commonly referred as electronic noses, enable the recognition of a type and a concentration of various volatile compounds. Typical electronic gas-analyzing device consists of four main elements, namely, gas delivery subsystem, an array of gas sensors, data acquisition and power supply circuits and data analysis software. The commercially available metal-oxide TGS sensors are widely...
-
Impact of digital signal processing on FOC current feedback in high-speed PMSM drive
PublikacjaIn applications where size and weight of the electric motor are among major design concerns, Permanent Magnet Synchronous Motors (PMSMs) with wide operational speed-range are commonly preferred. Due to limited inverter switching frequency, high-speed operation of a drive results in a low ratio between the switching frequency and the fundamental frequency of motor voltage. Such operating conditions have been recently identified...
-
Denitrifcation rate in the mainstream deammonification
PublikacjaThe conventional processes of biological nitrogen removal based on nitrification and denitrification does not fit properly into the concept of the circular economy. As the alternative one should consider the deammonification process, which is a combination of partial nitrification (nitritation) and Anammox processes. It consists of removing ammonium nitrogen from wastewater under anaerobic conditions by a group of autotrophic microorganisms....
-
Probabilistic seismic assessment of RC box-girder highway bridges with unequal-height piers subjected to earthquake-induced pounding
PublikacjaThis paper uses the probabilistic seismic assessment to study the effects of pounding and irregularity on the seismic behavior of typical concrete box-girder bridges with four levels of altitudinal irregularity. To extend the results for all bridges in the same class, uncertainty related to the earthquake, structural geometries, and materials are considered. Pounding is likely to take place in two cases: the first one concerns...
-
Supramolecular deep eutectic solvents and their applications
PublikacjaIn recent years, the growing awareness of the harmfulness of chemicals to the environment has resulted in the development of green and sustainable technologies. The compromise between economy and environmental requirements is based on the development of new efficient and green solutions. Supramolecular deep eutectic solvents (SUPRADESs), a new deep eutectic solvent (DES) subclass characterized by inclusion properties, are a fresh...
-
UAV Photogrammetry under Poor Lighting Conditions—Accuracy Considerations
PublikacjaThe use of low-level photogrammetry is very broad, and studies in this field are conducted in many aspects. Most research and applications are based on image data acquired during the day, which seems natural and obvious. However, the authors of this paper draw attention to the potential and possible use of UAV photogrammetry during the darker time of the day. The potential of night-time images has not been yet widely recognized,...
-
Electron attachment to representative cations composing ionic liquids
PublikacjaUsing ab initio electronic structure methods with flexible atomic orbital basis sets, we investigated the electronic structure and stability of reduction products of selected representative cations (C+) constituting ionic liquids. We found that an electron attachment to such cations leads to the neutral radicals, whereas a subsequent attachment of another (i.e., excess) electron leads to adiabatically stable anions only in two...
-
Comprehensive evaluation of the carbon footprint components of wastewater treatment plants located in the Baltic Sea region
PublikacjaFinland and Poland share similar environmental interests with regard to their wastewater effluents eventually being discharged to the Baltic Sea. However, differences in the influent wastewater characteristics, treatment processes, operational conditions, and carbon intensities of energy mixes in both countries make these two countries interesting for carbon footprint (CF) comparison. This study aimed at proposing a functional...
-
Open-source software (OSS) and hardware (OSH) in UAVs
PublikacjaThe popularity of the Open Source Tool (OST) has expanded significantly. This is the case for Unmanned Aerial Vehicles (UAVs) based on open-source hardware (OSH) as well. Open-source software (OSS) and OSH can be applied in a wide range of applications and can improve several technologies. The chapter begins with an introduction to OSS depicting its rationale, description of fundamental differences between OSS and proprietary software...
-
Dynamic analysis of temporary steel grandstand subjected to human-induced excitations due to jumping
PublikacjaSteel grandstands are structures that are frequently used during sport games and many other non-sporting events, such as festivals, music concerts, or even politicians rallies, with participation of a large number of attendees. Unfortunately, the presence of unexpected excessive dynamic loads due to unpredictable behaviour of spectators (e.g. synchronized harmonic jumping or swaying) may lead to...
-
Distributed Architectures for Intensive Urban Computing: A Case Study on Smart Lighting for Sustainable Cities
PublikacjaNew information and communication technologies have contributed to the development of the smart city concept. On a physical level, this paradigm is characterised by deploying a substantial number of different devices that can sense their surroundings and generate a large amount of data. The most typical case is image and video acquisition sensors. Recently, these types of sensors are found in abundance in urban spaces and are responsible...
-
Testing the Positioning Accuracy of GNSS Solutions during the Tramway Track Mobile Satellite Measurements in Diverse Urban Signal Reception Conditions
PublikacjaMobile Global Navigation Satellite System (GNSS) measurements carried out on the railway consist of using satellite navigation systems to determine the track geometry of a moving railway vehicle on a given route. Their purposes include diagnostics, stocktaking, and design work in railways. The greatest advantage of this method is the ability to perform measurements in a unified and coherent spatial reference system, which...
-
Właściwości niskotemperaturowe betonów asfaltowych o wysokim module sztywności (AC-WMS) w badaniach trzypunktowego zginania
PublikacjaArtykuł przedstawia właściwości niskotemperaturowe betonów asfaltowych o wysokim module sztywności. Przedstawione wyniki zostały uzyskane w dwóch badaniach zginania trzypunktowego próbek belkowych: ze stałą prędkością przemieszczenia oraz pod stałym obciążeniem. Obie te metody są od dawna stosowane na Politechnice Gdańskiej do oceny właściwości niskotemperaturowych betonów asfaltowych. Badaniu poddano pięć betonów asfaltowych –...
-
Survey on fuzzy logic methods in control systems of electromechanical plants
PublikacjaРассмотрены алгоритмы управления электромеханическими системами с использованием теории нечеткой логики, приводятся основные положения их синтеза, рассматриваются методы анализа их устойчивости на основе нечетких функций Ляпунова. Эти алгоритмы чаще всего реализуются в виде различных регуляторов, применение которых целесообразно в системах, математическая модель которых не известна, не детерминирована или является строго нелинейной,...
-
Changes in Functional and Spatial Layouts of Polish Single-Family Houses
PublikacjaArticle presents the evolution of functional and spatial layouts of single-family houses in Poland, with particular emphasis on the functions of a contemporary house. Singlefamily housing constitutes a significant part of the construction market in Poland. The way of forming functions in single-family buildings in the historical cycle has characteristic features resulting from the culture of the society in a given period. The functional...
-
Influence of the notch rounding radius on estimating the elastic notch stress concentration factor in a laser welded tee joint
PublikacjaIn recent years an increased interest of industry in sandwich-type metal structures can be observed. These structures consist of thin plates of 2.5 mm in thickness separated by stiffeners of different shapes and forms. Welds joining the plates and stiffeners are made on the outer side of the plates using laser welding technique. A locally focused source of heat causes the plate to melt creating a very narrow and elongated joint....
-
The effect of numerical 2D and 3D FEM element modelling on strain and stress distributions at laser weld notches in steel sandwich type panels
PublikacjaLike other means of transport, merchant ships face the problem of increasing requirements concerning the environment protection, which, among other issues, implies the reduction of fuel consumption by the ship. Here, the conventional approach which consists in making use of higher strength steels to decrease the mass of the ship hull can be complemented by the use of new steel structures of sandwich panel type. However, the lack...
-
Identification of category associations using a multilabel classifier
PublikacjaDescription of the data using categories allows one to describe it on a higher abstraction level. In this way, we can operate on aggregated groups of the information, allowing one to see relationships that do not appear explicit when we analyze the individual objects separately. In this paper we present automatic identification of the associations between categories used for organization of the textual data. As experimental data...
-
Improving automatic surveillance by sound analysis
PublikacjaAn automatic surveillance system, based on event detection in the video image can be improved by implementing algorithms for audio analysis. Dangerous or illegal actions are often connected with distinctive sound events like screams or sudden bursts of energy. A method for detection and classification of alarming sound events is presented. Detection is based on the observation of sudden changes in sound level in distinctive sub-bands...
-
Audio content analysis in the urban area telemonitoring system
PublikacjaArtykuł przedstawia możliwości rozwinięcie monitoringu miejskiego o automatyczną analizę dźwięku. Przedstawiono metody parametryzacji dźwięku, które możliwe są do zastosowania w takim systemie oraz omówiono aspekty techniczne implementacji. W kolejnej części przedstawiono system decyzyjny oparty na drzewach zastosowany w systemie. System ten rozpoznaje dźwięki niebezpieczne (strzał, rozbita szyba, krzyk) wśród dźwięków zarejestrowanych...
-
Identification and characterization of single-stranded DNA-binding protein from the facultative psychrophilic bacteria Pseudoalteromonas haloplanktis
PublikacjaSingle-stranded DNA-binding protein (SSB) plays an important role in DNA metabolism such as DNAreplication, repair, and recombination, and is essential for cell survival. This study reports on the ssb-likegene cloning, gene expression and characterization of a single-stranded DNA-binding protein of Pseudoal-teromonas haloplanktis (PhaSSB) and is the first report of such a protein from psychrophilic microorganism.PhaSSB possesses...
-
Estimation of Stresses in a Dry Sand Layer Tested on Shaking Table
PublikacjaTheoretical analysis of shaking table experiments, simulating earthquake response of a dry sand layer, is presented. The aim of such experiments is to study seismic-induced compaction of soil and resulting settlements. In order to determine the soil compaction, the cyclic stresses and strains should be calculated first. These stresses are caused by the cyclic horizontal acceleration at the base of soil layer, so it is important...
-
Verification of agent system for it project management support
PublikacjaThis article is a continuation of article series telling about research about possibility of using agent system to information technology evaluation. Following article presents full conception of exploiting agent system and shows how it can support some managers works, especially in taking correct management method and information tool for project management. In this article the agent system that based on knowledge and can process...
-
Fracture Surface Topography Parameters for S235JR Steel Adhesive Joints After Fatigue Shear Testing
PublikacjaThis paper presents the experimental results of a study investigating the effect of holes and notches made on the overlap ends on the strength of adhesive joints. Single-lap joints made of S235JR steel sheets bonded with Araldite 2024-2 epoxy adhesive were tested. For comparative reasons, static shear strength tests and high-cycle fatigue strength tests were performed. Adhesive-filled joints having three holes, each with a diameter...
-
‘Personas for lighting’. Three methods to develop personas for the indoor lighting environment
PublikacjaThe objective of this research is to describe and compare three different methods of generating ‘persona for lighting’ to envision users’ behaviour within the lighting environment. ‘Personas’ are used to represent typical users, highlighting their needs, perspectives, and expectations to aid user-centric design approaches. The researchers looked for the most useful method of shaping ‘personas for lighting’ to learn about users’...
-
Near-Field Wireless Sensing of Plastics and Papers Using Frugal Peel-Off Passive Tag
PublikacjaThis article presents a novel frugal approach of testing plastics and papers using a near-field microwave sensing technique with a peel-off tag. The proposed sensing technique involves two electrical entities: the sensor, which may be regarded as a reader, and a disposable tag. The reader is a modified design of a gap-coupled microstrip line (GCML) sensor, while the passive tag is a standard double-ring complementary split-ring...
-
Tuning Electrochemical Performance by Microstructural Optimization of the Nanocrystalline Functional Oxygen Electrode Layer for Solid Oxide Cells
PublikacjaFurther development of solid oxide fuel cell (SOFC) oxygen electrodes can be achieved through improvements in oxygen electrode design by microstructure miniaturisation alongside nanomaterials implementation. In this work, improved electrochemical performance of an La0.6Sr0.4Co0.2Fe0.8O3-d (LSCF) cathode was achieved by the controlled modification of the La0.6Sr0.4CoO3-d (LSC) nanocrystalline interlayer introduced between a porous...
-
Adaptive Algorithm of a Tap-Changer Controller of the Power Transformer Supplying the Radial Network Reducing the Risk of Voltage Collapse
Publikacjahe development of renewable energy, including wind farms, photovoltaic farms as well as prosumer installations, and the development of electromobility pose new challenges for network operators. The results of these changes are, among others, the change of network load profiles and load flows determining greater volatility of voltages. Most of the proposed solutions do not assume a change of the transformer regulator algorithm....
-
Experimental study on the seepage flow through the ice jam
PublikacjaIn light of the observed climate change, there is a need for better understanding of river ice processes for managing water resources in the cold regions. Ice jams produce significant resistance which may cause rise of water level and flooding. The jam resistance is only referred to the roughness of its underside, and this approach lead to exceptional roughness coefficients which has no physical explanation. Number of evidences...
-
The Influence of Calcium Glycerophosphate (GPCa) Modifier on Physicochemical, Mechanical, and Biological Performance of Polyurethanes Applicable as Biomaterials for Bone Tissue Scaffolds Fabrication
PublikacjaIn this paper we describe the synthesis of poly(ester ether urethane)s (PEEURs) by using selected raw materials to reach a biocompatible polyurethane (PU) for biomedical applications. PEEURs were synthesized by using aliphatic 1,6-hexamethylene diisocyanate (HDI), poly(ethylene glycol) (PEG), α,ω-dihydroxy(ethylene-butylene adipate) (Polios), 1,4-butanediol (BDO) as a chain extender and calcium glycerolphosphate salt (GPCa) as...
-
Investigation of behaviour of metal structures with polymer dampers under dynamic loads
PublikacjaA large number of accidents concerning structures subjected to dynamic loads have been recently observed. One of the examples of such a structure is a temporary steel grandstand erected using scaffolding system. Dynamic load that is generated by crowd movement has a significant influence on the behaviour of the structure and may lead to excessive structural vibrations. The aim of the study is to consider the idea of using polymer...
-
Features of load and wear of main propulsion devices on sea-going ships with piston combustion engines and their impact on changes in technical states of the systems
PublikacjaThe paper presents the specificity of operation of propulsion systems of seagoing ships which causes the need to control the load on them, especially on their engines called main engines. The characteristics of the load on the propulsion systems, especially on the main engines as well as on the shaft lines and propellers driven by the engines, along with the process of wear in tribological joints (sliding tribological systems)...
-
The optimization of enzyme immobilization at Au-Ti nanotextured platform and its impact onto the response towards glucose in neutral media
PublikacjaThe market of non-invasive glucose sensors is drastically growing due to increasing number of people suffering from diabetes. Therefore, there is a significant need for any improvement in the field of biosensors that can be used for monitoring glucose level in human body. In recent years the emphasis is put onto the modification of electrode material with enzymes possessing recognition centre specific towards particular molecules....
-
Longitudinal Motion Due to Action of Tunnel Thrusters
PublikacjaTunnel thrusters are propulsion and active control devises that provide a side force, or transverse thrust, to support mooring operations or position keeping. They shorten the time of manoeuvring, reduce the cost of towage and since inception, manoeuvrability specifically in ports has become a lot easier. Tunnel thrusters can either be operated manually or with the help of Dynamic Positioning systems which makes it even more efficient. Theoretically,...
-
Generalized Formulation of Response Features for Reliable Optimization of Antenna Input Characteristics
PublikacjaElectromagnetic (EM)-driven parameter adjustment has become imperative in the design of modern antennas. It is necessary because the initial designs rendered through topology evolution, parameter sweeping, or theoretical models, are often of poor quality and need to be improved to satisfy stringent performance requirements. Given multiple objectives, constraints, and a typically large number of geometry parameters, the design closure...
-
Smart Decisional DNA Technology to Enhance Industry 4.0 Environment in Conjunction with Conventional Manufacturing
PublikacjaKnowledge-based support has become an indispensable part not only to the traditional manufacturing set-ups but also to the new fast-emerging Industry 4.0 scenario. In this regard, successful research has been performed and extensively reported to develop Decisional DNA based knowledge representation models of engineering object and engineering process called Virtual engineering object (VEO), Virtual engineering process (VEP) and...
-
Faults and Fault Detection Methods in Electric Drives
PublikacjaThe chapter presents a review of faults and fault detection methods in electric drives. Typical faults are presented that arises for the induction motor, which is valued in the industry for its robust construction and cost-effective production. Moreover, a summary is presented of detectable faults in conjunction with the required physical information that allow a detection of specific faults. In order to address faults of a complete...
-
Viability of fruit seed oil O/W emulsions in personal care products
PublikacjaThe use of fruit seed oils in personal care products is of significance to both their function and image. Poland is an important processor of fruit products within the EU, and thus has a large availability of seeds from domestic fruits, which are normally considered to be a waste material or feed for livestock. Unfortunately, current literature is scarce of the suitability of these oils for topical dermatological use in the form...
-
Effects of Bromine Doping on the Structural Properties and Band Gap of CH3NH3Pb(I1–xBrx)3 Perovskite
PublikacjaAn experimental and theoretical study is reported to investigate the influence of bromine doping on CH3NH3Pb(I1−xBrx)3 perovskite for Br compositions ranging from x = 0 to x = 0.1, in which the material remains in the tetragonal phase. The experimental band gap is deduced from UV−vis absorption spectroscopy and displays a linear behavior as a function of bromine concentration. Density functional theory calculations are performed...
-
Synthesis of 3-(2-Alkylthio-4-chloro-5-methylbenzenesulfonyl)-2-(1-phenyl-3-arylprop-2-enylideneamino)guanidine Derivatives with Pro-Apoptotic Activity against Cancer Cells
PublikacjaThe untypical course of reaction between chalcones and benzenesulfonylaminoguanidines led to the new 3-(2-alkylthio-4-chloro-5-methylbenzenesulfonyl)-2-(1-phenyl-3-arylprop-2- enylideneamino)guanidine derivatives 8–33. The new compounds were tested in vitro for their impact on the growth of breast cancer cells MCF-7, cervical cancer cells HeLa and colon cancer cells HCT-116 by MTT assay. The results revealed that the activity of...
-
ATTITUDE OF YOUTH TO SELECT SPECIALTY AND QUALITY OF EDUCATION
PublikacjaThe problems of young people guidance on the choice of profession according to the labour market requirements and the education quality are considered. The problem of youth education and employment is very topical, and in relation to vocational education the main theoretical and practical approaches to its modernization should be changed. The paper is determined the key aspects for choosing the University to receive education and...
-
Examination of epigenetic inhibitor zebularine in treatment of skin wounds in healthy and diabetic mice
PublikacjaDNA methyltransferase inhibitor zebularine was proven to induce regeneration in the ear pinna in mice. We utilized a dorsal skin wound model to further evaluate this epigenetic inhibitor in wound healing. Full-thickness excisional wounds were made on the dorsum of 2 and 10-month-old healthy BALB/c and 3 and 8-month-old diabetic (db/db) mice, followed by topical or intraperitoneal zebularine delivery. Depending on the strain, age,...
-
Characterization of single-stranded DNA-binding proteins from the psychrophilic bacteria Desulfotalea psychrophila, Flavobacterium psychrophilum, Psychrobacter arcticus, Psychrobacter cryohalolentis, Psychromonas ingrahamii, Psychroflexus torquis, and Photobacterium profundum
PublikacjaBackground: Single-stranded DNA-binding proteins (SSBs) play essential roles in DNA replication, recombination and repair in Bacteria, Archaea and Eukarya. In recent years, there has been an increasing interest in SSBs, since they find numerous applications in diverse molecular biology and analytical methods. Results: We report the characterization of single-stranded DNA-binding proteins from the psychrophilic bacteria Desulfotalea...
-
A new procedure for the determination of distillation temperature distribution of high-boiling petroleum products and fractions
PublikacjaThe distribution of distillation temperatures of liquid and semi-fluid products, including petroleum fractions and products, is an important process and practical parameter. It provides information on properties of crude oil and content of particular fractions, classified on the basis of their boiling points, as well as the optimum conditions of atmospheric or vacuum distillation. At present, the distribution of distillation temperatures...
-
Micro-cracking pattern recognition of hybrid CNTs/GNPs cement pastes under three-point bending loading using acoustic emission technique
PublikacjaThe generation of microcracks has an important influence on the behaviour of concrete structures. In this study, the acoustic emission (AE) technique was used to investigate the fracture phenomena and micro-cracking behavior of hybrid carbon nanotubes (CNTs, the 1-D allotrope of carbon atoms) and graphene nanoplatelets (GNPs, 2D monolayer of sp2-hybridized carbon atoms), cement composites under three-point bending loading. In...
-
Influence of bush wear in water lubricated marine stern tube bearings with shaft misalignment
PublikacjaWater lubricated propeller shaft bearings are frequently employed on modern ships due to their advantages such as durability, simplicity and low price. Specific working conditions on ships cause shaft misalignment which often results in rapid wearing of bush and shaft. Shaft misalignment could be an effect of manufacturing or assembly faults but sometimes it appears due to hull or shaft deformation. The wearing process has influence...
-
Fabrication and characterization of boron-doped nanocrystalline diamond-coated MEMS probes
PublikacjaFabrication processes of thin boron-doped nanocrystalline diamond (B-NCD) films on silicon-based micro- and nano-electromechanical structures have been investigated. Nanocrystalline boron doped -diamond (B-NCD) films were deposited using Microwave Plasma Assisted Chemical Vapour Deposition (MW PA CVD) method. The variation of B-NCD morphology, structure and optical parameters were particularly investigated. The use of truncated...