Filtry
wszystkich: 3274
wybranych: 3179
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: HAEMOPHILUS INFLUENZAE
-
Influence of cyclic frozen and defrost on mechanical properties of polytetrafluoroethylene (PTFE)-coated woven fabrics
PublikacjaThis research aims to determine the influence of the cyclic process of freezing and defrosting on the mechanical properties of the chosen glass fibres and PTFE-coated woven fabrics. The specimens were subjected to freezing at about −20 °C for 4 h and thawing by full immersion into the water at about +20 °C for 4 h. The fabric samples after 25 and 50 frozen cycles were air-dried at room temperature for one week and then subjected...
-
Influence of controlled crystallization and SrF2 content on the structure and properties of Eu3+ doped phosphate glasses
PublikacjaNew phosphate glasses and glass-ceramics P2O5–Bi2O3–K2O–Nb2O5-SrF2 doped with Eu were synthesized and studied in this work. The influence of the SrF2 content (0–15 mol%) and the parameters of the heat treatment on their structural and optical properties were investigated. For the above purpose, the structural characterization by FTIR spectroscopy and XRD measurements was carried out, which showed a significant effect of SrF2 on...
-
Sources of contamination in sediments of retention tanks and the influence of precipitation type on the size of pollution load
PublikacjaDensification of cities and urban population contributes to increased runoff and suspended solids and alteration of the urban water cycle. Nowadays, Blue-Green Infrastructure is promoted to increase a city’s resilience to floods; however, stormwater drainage systems, supported with retention tanks are still important in protecting urban areas against floods. Sediment accumulation in stormwater infrastructure relates to an issue...
-
Cross-border transmission line configuration influence on the electrical power and energy billing process
PublikacjaIn 2015 a connection between the Polish and Lithuanian power systems become fully operational. The connection consists of a 400 kV double circuit transmission line and a back-to-back HVDC substation located on the Lithuanian side. A magnetic couplings between the circuits of the transmission line cause that during power transmission a different values of active power losses are observed in both circuits. This situation may cause...
-
Influence of Diosmin Treatment on the Level of Oxidative Stress Markers in Patients with Chronic Venous Insufficiency
PublikacjaOxidative stress plays an important role in the pathophysiology of many human disorders, while antioxidants prevent the development of various adverse symptoms. Diosmin is a natural flavonoid applied in vascular system disorders, especially in chronic venous insufficiency (CVI), and it plays a significant part in the alleviation of CVI symptoms. Due to antioxidant activity, it also has the ability to scavenge the oxygen free radicals...
-
Gas Composition Influence on the Properties of Boron-Doped Diamond Films Deposited on the Fused Silica
PublikacjaThe main subject of this study are molecular structures and optical properties of boron-doped diamond films with [B]/[C] ppm ratio between 1000 and 10 000, fabricated in two molar ratios of CH 4 -H 2 mixture (1 % and 4 %). Boron-doped diamond (BDD) film on the fused silica was presented as a conductive coating for optical and electronic purposes. The scanning electron microscopy images showed homogenous and polycrystalline surface...
-
Influence of steam cooking on pro-health properties of Small and Large variety of Momordica charantia
PublikacjaSteam cooking is one of the most common preparations of Momordicacharantia dishes. This method improved the tastiness of the fruits but at the same time, some changes occurred in the volatile and non-volatile parts of their food matrices. In this study, for the first time these properties were correlated with the found substances affecting the bioactivity of this fruit. Two varieties of Momordicacharantia were analysed and compared....
-
Influence of ESPAR antenna radiation patterns shape on PPCC-based DoA estimation accuracy
PublikacjaIn the article, we show the influence of three different electronically steerable parasitic array radiator (ESPAR) antenna radiation patterns on the overall direction of arrival (DoA) estimation accuracy when power-pattern cross-correlation (PPCC) algorithm, relying on received signal strength (RSS) values, is used for the estimation. The ESPAR antenna designs were obtained for three optimization goals, which resulted in different...
-
Forecasted climate changes and their influence on cities and regions in 2050 in terms of extreme hydrological events
PublikacjaGlobal climate change is a problem which arises numerous theories and uncertainties, especially in terms of speculated human impact. Independent from the fact, what is the main driver for the changes, some of the climate shifts are visible already nowadays. Both contemporary and future cities will have to face such problems. Although climate change may cause numerous effects on different fields, a special stress in this article...
-
The influence of the welding environment on the properties of Tekken joints made from S355J2C+N steel
PublikacjaThere are three main methods of underwater welding: dry, wet and intermediate between them, by using the local dry chamber. Due to low costs, the most common method is the wet welding with the use of covered electrodes. Water as a welding environment carries out a lot of problems. The first is limited visibility and instability of the welding arc. The biggest problem during underwater welding is high susceptibility to cold cracking,...
-
Postquarter-Point Case of Ship’s Side-Berthing and Its Influence on Marine Fender Pitch
PublikacjaThis paper presents a critical analysis of some selected codes and practical recommendations used as basic rules in the design procedures of modern marine fender systems. The first part of the discussion pertains to the existing equations used in calculating the eccentricity coefficient in the ship’s kinetic energy equation and the maximum allowable fender pitch (spacing) in a set of fenders installed along a quay wall. A new approach...
-
The influence of solution annealing temperature on the properties of Lean Duplex 2101 welded joints in tubes
PublikacjaThe article presents a technology of TIG longitudinal welding without filler material (142) of heat exchanger tubes made of Lean Duplex 2101. The results of studies on the effect of heat treatment (solution annealing) on tensile strength, plasticity, delta ferrite and the structure of smooth tubes are shown. It was found, that the change in solution annealing temperature across the tested range has an impact on mechanical properties...
-
The Influence of Microstructure on the Passive Layer Chemistry and Corrosion Resistance for Some Titanium-Based Alloys
PublikacjaThe effect of microstructure and chemistry on the kinetics of passive layer growth and passivity breakdown of some Ti-based alloys, namely Ti-6Al-4V, Ti-6Al-7Nb and TC21 alloys, was studied. The rate of pitting corrosion was evaluated using cyclic polarization measurements. Chronoamperometry was applied to assess the passive layer growth kinetics and breakdown. Microstructure influence on the uniform corrosion rate of these alloys...
-
The influence of water and mineral oil on volumetric losses in the displacement pump for offshore and marine applications
PublikacjaIn this paper volumetric losses in a positive displacement pump supplied with water and mineral oil are described and compared. The experimental tests were conducted using a prototype of a satellite pump (with a non-circular tooth working mechanism). In this paper the sources of volumetric losses in this pump are characterised. On this basis, a mathematical model of these losses has been presented. The results of the calculation...
-
Modulated photocurrents in a sandwich-cell structure: II. Influence of biasillumination intensity and carrier diffusion
PublikacjaPodano przybliżone wyrażenia opisujące modulowane fotoprądy (na podstawiemodelu wielokrotnego pułapkowania) w uwzględnieniem czynników wymienionych wtytule. Zbadano numerycznie ich wpływ na modulowane fotoprądy dla modelowychrozkładów pułapek. Otrzymano wzór - kryterium zaniedbania wpływu dyfuzji nafotoprądy.
-
The influence of the motor filtrers on harmonic current emmision in the pro-ective connection of drive systems.
PublikacjaThis paper contains detailed analysis of currents in protective wire in engine supplied from frequency converter without any external filters added. It was found that the peak value of current in protective conductor of engine was about 1500 mA at frequencies 5 Hz 50 Hz. In the continuation of research the dU/dt type motor filter and the sinusoidal filter were tested. It was found that the current in protective wire decreased...
-
Random components influence on the values characterising periodic disturbances in low voltage supply lines.
PublikacjaAnalizowano wpływ składowych losowych na wielkości charakteryzujących zaburzenia okresowe w napięciu zasilania na przykładzie współczynnika zawartości harmonicznych (THD). Zaprezentowano sposób wyznaczania niepewności pomiaru współczynnika THD, uwzględniający występowanie korelacji pomiędzy składową podstawową i kolejnymi harmonicznymi napięcia sieci a także między poszczególnymi harmonicznymi. Przedstawiono analizę wyników z pomiarów...
-
The influence of hard segment crosslinking on the morphology and mechanical properties of segmented poly(ester-urethanes)
PublikacjaPrównano właściwości i morfologie usieciowanych trójmetylolopropanem (TMP) i nieusieciowanych poliestrouretanów formowanych reaktywnie. W nieusieciowanych poliestrouretanach stwierdzono za pomocą AFM obecność agregacji domen segmentów sztywnych o wymiarze 70-380 nm. W usieciowanych poliuretanach zaobserwowano jedynie jednolicie rozmieszczone domeny segmentów sztywnych wielkości 20 nm. Właściwości mechaniczne wyraźnie różniły się,...
-
Influence of porous coating on heat transfer during flow boiling of R22, R134a and R407C
PublikacjaPrzedstawiono wpływ pwłoki porowatej w pozionej rurce podczas wrzenia w przepływie i spadku ciśnienia czynników chłodniczych R22, R134a i R407C.
-
The Influence of UV Light on Performance of Poly(methyl Methacrylate) in Regard to Dye-Sensitised Solar Cells
Publikacja -
Influence of analysis of features geometrical abrasive grains stress, strain and displacement of material in zone microgrinding
Publikacja -
Molecular dynamics study on the influence of C-terminal sugar substitution on dynamics and conformation of vancomycin derivatives
Publikacja -
The influence of ICT instruments on a transmission of interest rates by business entities and public authorities – A scientific comment
Publikacja -
Studying the Influence of the Impact Gap Value on the Average Translational Speed of the Wheeled Vibration-Driven Robot
Publikacja -
The Influence of Weather Anomalies on Mercury Cycling in the Marine Coastal Zone of the Southern Baltic—Future Perspective
Publikacja -
The Influence of Synthetic Oxygenates on Euro IV Diesel Passenger Car Exhaust Emissions - Part 2
Publikacja -
The Influence of Synthetic Oxygenates on Euro IV Diesel Passenger Car Exhaust Emissions - Part 3
Publikacja -
Does social–economical transformation influence the incidence of type 1 diabetes mellitus? A Polish example
Publikacja -
Influence of the Multiple Injection Moulding and Composting Time on the Properties of Selected Packaging and Furan-Based Polyesters
Publikacja -
The isomerization of α-pinene over the Ti-SBA-15 catalyst—the influence of catalyst content and temperature
Publikacja -
Influence of the Titanium Content in the Ti-MCM-41 Catalyst on the Course of the α-Pinene Isomerization Process
Publikacja -
Influence of increased arterial stiffness on myocardial work efficiency in patients with stable coronary artery disease
Publikacja -
Moisture Influence on Compressive Strength of Calcium Silicate Masonry Units–Experimental Assessment and Normative Calculations
Publikacja -
Influence of addition of cobalamin to the extender on the post-thaw motility, viability, and DNA integrity of bovine ejaculate
Publikacja -
Influence of e-beam irradiation on poly(aliphatic/aromatic-ester) multiblock copolymers used as biomaterials
PublikacjaThe use of polymers became more relevant in medical applications for the versatility in processing and enhanced material properties of polymers. In order to be suitable as a biomaterial, it is of medical importance that these polymers are biocompatible and do not elicit negative responses from the body after implantation. Furthermore during the course of usage under load-bearing conditions, these biomaterials must sustain dynamical...
-
The influence of extracts from Rubus caesius leaves on human colon carcinoma cells cultured in vitro
Publikacja -
Influence of foliar fertilisation with calcium fertilisers on the firmness and chemical composition of two highbush blueberry cultivars
Publikacja -
The influence of street conditions on sea buckthorn fruit quality and content of micro- and macronutrients in berries and in soil
Publikacja -
Influence of various types of light on growth and physicochemical composition of blueberry (Vaccinium corymbosum L.) leaves
Publikacja -
Experimental research of circular saw blade tooth axial run-out influence on cutting effects
PublikacjaW pracy przedstawiono metodę pomiaru i wyniki badań doświadczalnych wpływu bicia osiowego ostrzy piły tarczowej na efekty przecinania
-
Influence of the engine cooling down period during short car stops on the average fuel consumption
PublikacjaW publikacji przedstawiono wpływ schłodzenia silnika podczas krótkich postojów pomiędzy jazdami na średnie zużycie paliwa. Przeprowadzono własne pomiary w czasie jazd miejskich w Gdańsku. Użyto samochodu osobowego z silnikiem o objętości skokowej 2 dm^3 z zapłonem siskrowym. Mierzono zużycie paliwa na trasach o długości 3-10 km. Krótko opisano sposoby wstępnego podgrzania silnika przed rozruchem.
-
Heat transfer to car engine cooling system - influence of coolant flow through engine block
PublikacjaW artykule przedstawiono wyniki badań doświadczalnych nad wpływem nastawianej wydajności pompy cieczy na strumień odbieranego ciepła w silniku spalinowym. Wykorzystano hamownię silnikową z silnikiem o zapłonie iskrowym o objętości skokowej 1.8 dm^3. Przyjęto obciążenia silnika oporami ruchu samochodu na biegu bezpośrednim.
-
Influence of Analyte Flow Rate on Signal and Response Time of the Amperometric Gas Sensor with Nafion Membrane
PublikacjaW publikacji przedstawiono rezultaty badań nad wpływem zmian objętościowego natężenia przepływu gazu na sygnał i czas odpowiedzi prototypowego czujnika ditlenku siarki z membraną nafionową. Porównywano właściwości czujników różniących się materiałem elektrody pracującej oraz składem roztworu elektrolitu wewnętrznego. Zastosowano elektrody pracujące wykonane z napylonych próżniowo na powierzchnię membrany nafionowej złota i platyny....
-
Chapter 1 : Supply system influence on behaviour of an elektromechanical model - four bar/dc motor
PublikacjaPraca opisuje zagadnienia wspólnego modelowania układu wieloczłonowego i napędu elektrycznego. Analizowanym układem mechanicznym jest płaski czworobok przegubowy. Analizowany mechanizm zamodelowano jako układ wieloczłonowy z zamkniętymi wielobokami ciał. Do wymuszenia ruchu układu wykorzystano model silnika prądu stałego. Zaproponowano kilka alternatywnych sposobów zasilania silnika. Układem referencyjnym jest źródło prądu stałego....
-
Influence of cathodic-protection-induced hydrogenation on mechanical properties of two ship hull plate steels
PublikacjaPrzedstawiono wyniki próby rozciągania i udarowej Charpy V dla stali zwykłej wytrzymałości (kategorii A) i podwyższonej wytrzymałości (kat. AH32) zarówno w stanie dostawy jak i po nawodorowaniu (protektor Zn w słonej wodzie). Nawodorowanie obydwu stali zwiększyło nieco granicę plastyczności (Re) i wydłużenie (A), nie zmieniając (atal A) lub nieco zmniejszając przewężenie (Z). Wpływ nawodorowania na udarność był ewidentnie pozytywny...
-
Influence of hydrostatic pump operation period on performance of a thrust bearing of a 125 MW pump-turbine
Publikacja -
THE THEORETICAL STUDY ON INFLUENCE OF FUEL INJECTION PRESSURE ON COMBUSTION PARAMETERS OF THE MARINE 4-STROKE ENGINE
Publikacja -
Magnetic Field Influence on the Superconducting Transition in Granular (BiPb)-Sr-Ca-Cu-O Superconductors
Publikacja -
Influence of geosmin, dimethyl trisulfide, 2- and 3-methylbutan-1-ol on raw spirits quality
PublikacjaJakość napojów alkoholowych jest bardzo istotna dla konsumentów. Destylarnie, chcąc wytwarzać wysokiej jakości trunki, muszą określić, które składniki są odpowiedzialne za nieprzyjemny zapach pogarszając jakość otrzymywanych alkoholi. Głównym celem przeprowadzonych badań było określenie profili zapachowych próbek destylatów rolniczych różniących się jakością organoleptyczną oraz wskazanie tych składników, których obecność może...
-
The influence of different acids and pepsin on the extractability of collagen from the skin of Baltic cod (Gadus morhua)
PublikacjaZastosowano 5,0 M roztwory kwasu cytrynowego, mlekowego, octowego oraz 0,115 M roztwór kwasu solnego. Kolagen z całych skór ekstrahowano w 4 st.C odpowiednimi kwasami (1 : 6, w/v) w czasie 24, 48 i 72 h. Stwierdzono, że kwas solny jest najmniej efektywnym rozpuszczalnikiem kolagenu spośród użytych kwasów. W zastosowanych warunkach doświadczeń maksymalnie można wyekstrahować kwasem cytrynowym 60 % kolagenu, kwasem octowym i mlekowym...