Filtry
wszystkich: 2044
wybranych: 1345
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: PARTITION DIMENSION
-
Wear estimation of current collector contact strips by analysis of a 3D scanning results
PublikacjaThe technical condition of current collector contact strips is very important when operational reliability of railway transportation is considered. The authors proposed a novel measurement system based on a 3D camera to register the shape and dimensions of the current collector contact strips surface. The system was installed above the railway track for tests in target ambient. During the trial operation a few dozen of contact...
-
Multi-stage magnetic-fluid seals for operating in water - life test procedure, test stand and research results. Part II Results of life tests of multi-stage magnetic - fluid seal operating in water
PublikacjaThe edge criteria for magnetic-fluid seals durability research were described in previous article [24] and now the tests results are presented. The tests were made with three magnetic fluids using various magnets quantity in magnetic assemblies. If values obtained in the repeated test deviated by more than 10 % from results of the first test an additional control test was made for final characteristics. The characteristics are:...
-
Simulation-Based Design of Microstrip Linear Antenna Arrays Using Fast Radiation Response Surrogates
PublikacjaFast yet accurate technique for simulation-based design of linear arrays of microstrip patch antennas is presented. Our technique includes: (i) optimization of the corrected array factor of the antenna array under design for a phase excitation taper resulting in reduced side lobes; (ii) simulation-driven optimization of the array element for element dimensions resulting in matching at and about operational frequency, and (iii)...
-
Green Aspects of Miniaturized Sample Preparation Techniques
PublikacjaCorrect monitoring and control of the state of the environment and scientific research on the subject of environmental protection often require that determinations of compounds present at very low concentrations be made in samples characterized by a matrix of complex composition (e.g., biological samples, water and soil samples). Moreover, due to the limited number of analytical techniques which are sufficiently sensitive to conduct...
-
Modelling of the Heat Flux Density Distribution for Laser Beam Welding
PublikacjaGreat interest of the laser beam welding in industry is a new theoretical task, making planning the welding procedure specification and the quality control of welded joints easier. Estimating and calculating the dimensions of a weld pool and temperature distribution near weld mainly concern heat source modelling. In the presented work calculations of welding pool shape and thermal field for cylindrical-powered-normally model of...
-
Towards the value-based design of on-line services
PublikacjaThe paper identifies economic factors shaping customer bahaviour in on-line services in two interrelated dimensions; (1) economic needs and requirements, relevant to expected benefits and values perceived by customers; (2) technical components, allowing technical realization of on-line services. Technical components were cathegorized into four groups, creating so-called VIPR model: Visual, Interactive, Process and Relationship-relevant...
-
Plasmon-enhanced photoluminescence from TiO2 and TeO2 thin films doped by Eu3+ for optoelectronic applications
PublikacjaIn this work we study the luminescence properties of europium-doped titanium dioxide and tellurium oxide thin films enhanced by gold plasmonic nanostructures. We propose a new type of plasmon structure with an ultrathin dielectric film between plasmonic platform and luminescent material. Plasmonic platforms were manufactured through thermal annealing of the gold thin film. Thermal dewetting of gold film results in spherical gold...
-
Synthesis of a state feedback controller for an averaging tank with variable filling
PublikacjaIn paper, a nonlinear averaging tank with variable filling is considered. The main purpose of this research work was the modelling and control system synthesis of an averaging tank. The control objectives included ensuring stability and zero steady-state error of the system and achieving settling time as short as possible, while maintaining a minimal overshoot. In order to achieve the intended purpose, firstly a mathematical model...
-
An enhanced method in predicting tensile behaviour of corroded thick steel plate specimens by using random field approach
PublikacjaThe present work investigates the possibility of using random field techniques in modelling the mechanical behaviour of corroded thick steel plate specimens. The nonlinear Finite Element method, employing the explicit dynamic solver, is used to analyse the mechanical properties of typical specimens. A material model considering full nonlinearity is used to evaluate the stress-strain response. The influence of major governing parameters...
-
An Analysis of Airline GRI and SDG Reporting
PublikacjaThis study aims to increase our understanding of the Global Reporting Initiative’s (GRI) topic-specific disclosures and the sustainable development goals (SDGs) addressed in the global passenger airline industry’s sustainability reporting (SR). Based on a quantitative content analysis of the industry’s sustainability reports from the financial year 2019 (FY19), this study reveals that airlines focused more on reporting environmental...
-
Hydrogen direct reduction and reoxidation behaviour of high-grade pellets
PublikacjaHigh grade pellets with basicity index close to 0.5 were directly reduced in pure hydrogen atmosphere. The reduction experiments were performed in the temperature range 800 e1000 C at the pressure of 8 bar. The pellets internal structure was analysed through micro tomography observations in the unreduced and reduced conditions. After reduction, the pellets showed a variation of porosity up to more than 15% with a remarkable change...
-
A non-adiabatic wavepacket dynamical study of the low energy chargetransfer process in the S3+ + H collision
PublikacjaThe collisional system S3+ + H?S2+ + H+ has been studied using a time-dependent wavepacket methodologyin two-dimensions. Using available potential energy surfaces and coupling matrix elementsobtained from multireference ab initio calculations, five non-adiabatically coupled electronic states of1P symmetry have been included in the dynamical simulations. The collision has been studied in thelow energy regime of 1-10 eV. The wavepacket...
-
Sensitivity analysis of free torsional vibration frequencies of thin-walled laminated beams under axial load
PublikacjaThe paper addresses sensitivity analysis of free torsional vibration frequencies of thin-walled beams of bisymmetric open cross-section made of unidirectional fibre-reinforced laminate. The warping effect and the axial end load are taken into account. The consideration is based upon the classical theory of thin-walled beams of non-deformable cross-section. The first-order sensitivity variation of the frequencies is derived with...
-
Design and Experiments of a Piezoelectric Motor Using Three Rotating Mode Actuators
PublikacjaThis paper represents a numerical and experimental investigation of the multicell piezoelectric motor. The proposed design consists of three individual cells that are integrated into the stator, double rotor, and a preload system combined into a symmetrical structure of the motor. Each of the cells is characterized by a traveling wave and rotating mode motor. A finite element numerical analysis is carried out to obtain optimal...
-
Dynamic tests of composite footbridge segment – experimental and numerical studies
PublikacjaExperimental dynamic tests and numerical simulations of a 3 meters long segment of a footbridge made of polymer composites are presented in the paper. The span-length is reduced, however dimensions of cross-section are the same as the target footbridge. The segment structure is made of sandwich panels, which consist of fibre reinforced polymer (GFRP) laminates (skins) and a PET foam (core). The first part of the paper contains...
-
Mathematical model of pennate muscle
PublikacjaThe purpose of this study is to create a new mathematical model of pennate striated skeletal muscle. This new model describes behaviour of isolated flat pennate muscle in two dimensions (2D) by taking into account that rheological properties of muscle fibres depend on their planar arrangement. A new mathematical model is implemented in two types: 1) numerical model of unipennate muscle (unipennate model); 2) numerical model of...
-
From unextendible product bases to genuinely entangled subspaces
PublikacjaUnextendible product bases (UPBs) are interesting mathematical objects arising in composite Hilbert spaces that have found various applications in quantum information theory, for instance in a construction of bound entangled states or Bell inequalities without quantum violation. They are closely related to another important notion, completely entangled subspaces (CESs), which are those that do not contain any fully separable pure...
-
Design and optimization of a novel miniaturized low-profile circularly polarized wide-slot antenna
PublikacjaThis paper presents a novel structure of a compact circularly polarized (CP) antenna. CP is obtained using a parasitic quasi-rectangular strip placed coplanar to the feedline. A ground plane perturbation combined with the asymmetric geometry of the coplanar waveguide ground planes is utilized to excite additional CP modes. All antenna dimensions are rigorously optimized to achieve the best possible performance in terms of the impedance...
-
Generic appearance of objective results in quantum measurements
PublikacjaMeasurement is of central interest in quantum mechanics as it provides the link between the quantum world and the world of everyday experience. One of the features of everyday experience is its robust, objective character, contrasting the delicate nature of quantum systems. Here we analyze in a completely model-independent way the celebrated von Neumann measurement process, using recent techniques of information flow, studied in...
-
Inverse surrogate models for fast geometry scaling of miniaturized dual-band couplers
PublikacjaRe-design of microwave structures for various sets of performance specifications is a challenging task, particularly for compact components where considerable electromagnetic (EM) cross-couplings make the relationships between geometry parameters and the structure responses complex. Here, we address geometry scaling of miniaturized dual-band couplers by means of inverse surrogate modeling. Our approach allows for fast estimation...
-
Novel structure and design of compact UWB slot antenna
PublikacjaIn this paper, a novel structure of a compact UWB slot antenna is presented along with a simulation-driven design optimization algorithm for adjusting geometry parameters of the device. Our primary objective is to obtain small footprint of the structure while maintaining its acceptable electrical performance. It is achieved by introducing sufficiently large number of geometry degrees of freedom, including increased number of parameterized...
-
Particle Swarm Optimization Based Optimal Design of Six-Phase Induction Motor for Electric Propulsion of Submarines
PublikacjaRecent research reveals that multi-phase motors in electric propulsion systems are highly recommended due to their improved reliability and efficiency over traditional three phase motors. This research presented a comparison of optimal model design of a six phase squirrel cage induction motor (IM) for electric propulsion by using Genetic Algorithm (GA) and Particle Swarm Optimization (PSO). A six phase squirrel cage induction...
-
A comparison of geometric analogues of holographic reduced representations, original holographic reduced representations and binary spatter codes
PublikacjaGeometric Analogues of Holographic Reduced Representations (GA HRR) employ role-filler binding based on geometric products. Atomic objects are real-valued vectors in n-dimensional Euclidean space and complex statements belong to a hierarchy of multivectors. The paper reports a battery of tests aimed at comparison of GA HRR with Holographic Reduced Representation (HRR) and Binary Spatter Codes (BSC). Firstly, we perform a test of...
-
Particle Swarm Optimization Based Optimal Design of Six-Phase Induction Motor for Electric Propulsion of Submarines
PublikacjaAbstract: Recent research reveals that multi-phase motors in electric propulsion systems are highly recommended due to their improved reliability and efficiency over traditional three phase motors. This research presented a comparison of optimal model design of a six phase squirrel cage induction motor (IM) for electric propulsion by using Genetic Algorithm (GA) and Particle Swarm Optimization (PSO). A six phase squirrel cage induction...
-
Numerical Modelling for Prediction of Compression Index from Soil Index Properties in Jimma town, Ethiopia
PublikacjaIn this study, correlations are developed to predict compression index (Cc) from index parameters so that one can be able to model Jimma soils with compression index using simple laboratory tests. Undisturbed and disturbed soil samples from twelve different locations in Jimma town were collected. Laboratory tests like specific gravity, grain size analysis, Atterberg limit, and one-dimensional consolidation test for a total of twenty-four...
-
Flow maldistribution and its mitigation in mini heat exchangers
PublikacjaIn the present paper, a detailed numerical investigation has been carried out to analyze the flow maldistribution in 50 parallel 1 mm x 1 mm rectangular minichannels and 1 mm depth minigap section with rectangular, trapezoidal, triangular or concave mani-folds in Z-type flow configuration (16 different cases). The working medium was ethanol and the mass flow rate was 5×10-4 kg/s. Both sections was heated from the bottom side. Heat...
-
Simulations of freshwater lens recharge and salt/freshwater interfaces using the HYDRUS and SWI2 packages for MODFLOW
PublikacjaThe paper presents an evaluation of the combined use of the HYDRUS and SWI2 packages for MODFLOW as a potential tool for modeling recharge in coastal aquife rs subject to saltwater intrusion. The HYDRUS package for MODFLOW solves numerically the one-dimensional form of the Richards equation describing water flow in variably- saturated media. The code computes groundwater recharge to or...
-
Job-related emotions and job burnout among civil servants: examining the shape of the relationship in cross-sectional and longitudinal models
PublikacjaWstęp: Związek pozytywności, czyli proporcji między pozytywnymi a negatywnymi emocjami, z wypaleniem zawodowym może przybierać kształt krzywoliniowy. Ponadto z perspektywy teoretycznej jest to relacja przyczynowo - skutkowa, w której pozytywność jest proksymalnym, a wypalenie – dystalnym wymiarem dobrostanu zawodowego. Dotychczasowe badania były jednak prowadzone najczęściej w planie poprzecznym i testowały relacje prostoliniowe....
-
Seafloor characterisation using multibeam sonar echo signal processing and image analysis
PublikacjaThe authors propose the approach to multibeam seafloor characterisation which relies on the combined, concurrent use of two different techniques of multibeam sonar data processing. The first one is based on constructing the grey-level sonar images of seabed using the echoes received in the consecutive beams. Then, the parameters describing the local region of sonar image, namely, the local standard deviation of a grey level, and...
-
THE EFFECT OF LOG SORTING STRATEGY ON THE FORECASTED LUMBER VALUE AFTER SAWING PINE WOOD
PublikacjaThe optimal transformation path for the resource is determined by the quality of a log combined with its dimension. The commercial value of derived products is also closely connected with the size and extent of containing wood deficiencies. The results of studies with three diverse strategies for log sorting are presented in the paper. Resource assessment by a worker without extensive experience in sorting logs, the certified grading...
-
Empirical Relationship Describing Total Convective and Radiative Heat Loss in Buildings
PublikacjaOn the basis of theoretical considerations of convective-radiative heat transfer, a relationship was developed enabling the total convective and radiative heat flux QC+R emitted from any object at tw and its surroundings at t∞ to be calculated from known values of the surface temperature of such an object, i.e., the known temperature difference Δt=tw - t∞ and average air temperature Tav. This relationship is applied to thermal...
-
Strain energy density and entire fracture surface parameters relationship for LCF life prediction of additively manufactured 18Ni300 steel
PublikacjaIn this study, the connection between total strain energy density and fracture surface topography is investigated in additively manufactured maraging steel exposed to low-cycle fatigue loading. The specimens were fabricated using laser beam powder bed fusion (LB-PBF) and examined under fully-reversed strain-controlled setup at strain amplitudes scale from 0.3% to 1.0%. The post-mortem fracture surfaces were explored using a non-contact...
-
The Undisrupted Growth of the Airbnb Phenomenon between 2014–2020. The Touristification of European Cities before the COVID-19 Outbreak
PublikacjaAs a result of the Airbnb eruption, not only has the character of the short-term rental market been completely transformed, but the decades long growth in tourism has also been further accelerated. Therefore, due to the new demands of the tourism economy, the major shift in the usage of historic city centers occurred–the process of ‘touristification’, that results in the emergence of its new, unsustainable form. Despite the significance...
-
Optimization issues in distributed computing systems design
PublikacjaIn recent years, we observe a growing interest focused on distributed computing systems. Both industry and academia require increasing computational power to process and analyze large amount of data, including significant areas like analysis of medical data, earthquake, or weather forecast. Since distributed computing systems – similar to computer networks – are vulnerable to failures, survivability mechanisms are indispensable...
-
Pressure drop related to flow maldistribution in a model minichannel plate heat exchanger
PublikacjaThe paper describes the issues related to the pressure drop that accompanies the phenomenon of maldistribution of working fluid between the channels of a model minichannel plate heat exchanger. The research concerns a single exchanger's plate containing 51 (in every geometry) parallel rectangular minichannels of hydraulic diameters 461 µm, 571 µm, 750 µm and 823 µm. In addition, the more complex geometry has been investigated,...
-
Multidimensional Scaling Analysis Applied to Music Mood Recognition
PublikacjaThe paper presents two experiments aimed at categorizing mood associated with music. Two parts of a listening test were designed and carried out with a group of students, most of whom where users of online social music services. The initial experiment was designed to evaluate the extent to which a given label describes the mood of the particular music excerpt. The second subjective test was conducted to collect the similarity data...
-
A Quasi-2D MOSFET Model — 2D-to-Quasi-2D Transformation
PublikacjaA quasi-two-dimensional (quasi-2D) representation of the MOSFET channel is proposed in this work. The representation lays the foundations for a quasi 2D MOSFET model. The quasi 2D model is a result of a 2D into quasi 2D transformation. The basis for the transformation are an analysis of a current density vector field and such phenomena as Gradual Channel Detachment Effect (GCDE), Channel Thickness Modulation Effect (CTME), and...
-
Module architecture as alternative approach to traditional construction processes
PublikacjaModule architecture today is a special type of building construction process that combines repetitive design, low-cost production based on prefabricated elements and fast erection. Module does not mean the same as modular. In general, module architecture today refers to the design of any system composed of separate components, manufactured before in factory, that can be connected together at the building site much faster than normally....
-
Lax-Wendroff and McCormack Schemes for Numerical Simulation of Unsteady Gradually and Rapidly Varied Open Channel Flow
PublikacjaTwo explicit schemes of the finite difference method are presented and analyzed in the paper. The applicability of the Lax-Wendroff and McCormack schemes for modeling unsteady rapidly and gradually varied open channel flow is investigated. For simulation of the transcritical flow the original and improved McCormack scheme is used. The schemes are used for numerical solution of one dimensional Saint-Venant equations describing free...
-
Evolution of Animats Following a Moving Target in an Artificial Ecosystem
PublikacjaMany biological animals, even microscopically small, are able to track moving sources of food. In this paper, we investigate the emergence of such behavior in artificial animals (animats) in a 2-dimensional simulated liquid environment. These "predators" are controlled by evolving artificial gene regulatory networks encoded in linear genomes. The fate of the predators is determined only by their ability to gather food and reproduce—no...
-
Ammonium <i>O</i>,<i>O</i>'-diethyl dithiophosphate
PublikacjaIn the title compound, NH4+·(C2H5O)2PS2−, the ammonium cation is connected by four charge-assisted N−H···S hydrogen bonds to four tetrahedral O,O'-diethyl dithiophosphate anions, forming layers parallel to (100). The polar and non-polar constituents of the layers are stacked alternately along [100]. Interlacing of the external ethyl groups...
-
Experimental certification of an informationally complete quantum measurement in a device-independent protocol
PublikacjaMinimal informationally complete positive operator-valued measures (MIC-POVMs) are special kinds of measurement in quantum theory in which the statistics of their d2-outcomes are enough to reconstruct any d-dimensional quantum state. For this reason, MIC-POVMs are referred to as standard measurements for quantum information.Here, we report an experiment with entangled photon pairs that certifies, for what we believe is the first...
-
ON DYNAMICS OF ELASTIC NETWORKS WITH RIGID JUNCTIONS WITHIN NONLINEAR MICRO-POLAR ELASTICITY
PublikacjaWithin the nonlinear micropolar elasticity we discuss effective dynamic (kinetic) properties of elastic networks with rigid joints. The model of a hyperelastic micropolar continuum is based on two constitutive relations, i.e., static and kinetic ones. They introduce a strain energy density and a kinetic energy density, respectively. Here we consider a three-dimensional elastic network made of three families of elastic fibers connected...
-
On phase equilibrium of an elastic liquid shell with wedge disclination
PublikacjaBased on the six-parameter shell theory we consider the phase equilibrium of a two-phase liquid membrane containing a wedge disclination. The considered problems are related to modelling of phase transitions in biological or lipid membranes. In order to capture the membrane behaviour we consider a special case of elastic shells which energy is invariant under major transformations of a reference configuration and can be treated...
-
A role of the heat and work uncompensatedtransformations in the balance of entropy and theturbomachinery efficiency
PublikacjaIn the paper we have presented a procedure of estimating a role of the uncompensated transformation of heat and work in ow of viscous and heat conducting uid. The procedure was introduced by Professor Romuald Puzyrewski and is essential in local, in time and space, balance of entropy. Furthermore this unique approach leads to redenition the eciency of uid-ow machinery in three-dimensional modeling using CFD (Computational Fluid...
-
Searching for innovation knowledge: insight into KIBS companies
PublikacjaPurpose – The paper analyzes the patterns of research of “innovation knowledge” (i.e. knowledge that can result in introducing innovations in the company that can be observed in KIBS (Knowledge-Intensive Business Services) companies. Particularly, it identifies and classifies the possible approaches adopted by companies on the basis of two dimensions: the intensity/proactivity of search efforts, and the source primarily used. Design/methodology/approach...
-
Confidence, Financial Literacy and Investment in Risky Assets: Evidence from the Survey of Consumer Finances
PublikacjaWe employ recent Survey of Consumer Finances (SCF) microdata from the US to analyze the impacts of confidence in one's own financial knowledge, confidence in the economy, and objective financial literacy on investment in risky financial assets (equity and bonds) on both the extensive and intensive margins. Controlling for a rich set of covariates including risk aversion, we find that objective financial literacy is positively...
-
Measurements of Path Loss in Off-Body Channels in Indoor Environments
PublikacjaThis paper presents a measurements of the path loss for validation of a statistical model for off-body radio channels in an indoor multipath environment, which considers the distance dependent mean path loss, and describes body shadowing and fast fading components in a statistical way. The measurement equipment and propagation indoor environment have been presented. Two different bodies and five static and two walking scenarios...
-
An extended basis inexact shift–invert Lanczos for the efficient solution of large-scale generalized eigenproblems
PublikacjaThis paper proposes a technique, based on the Inexact Shift–Invert Lanczos (ISIL) method with Inexact Jacobi Orthogonal Component Correction (IJOCC) refinement, and a preconditioned conjugate-gradient (PCG) linear solver with multilevel preconditioner, for finding several eigenvalues for generalized symmetric eigenproblems. Several eigenvalues are found by constructing (with the ISIL process) an extended projection basis. Presented...
-
Methodology for determination of the selected mechanical properties of wood based on cutting tests
PublikacjaFrom kiln-dried spruce wood (with steam) as well as in natural conditions were randomly selected 8 samples. After determining the average dimensions, moisture content and density of the samples they have been cut on the frame sawing machine PRW15M for measurement of cutting power. Based on those results from a linear rela-tionship of cutting power versus feed per toot mechanical properties of wood such as facture toughness and...