Wyszukiwarka
Filtry
wszystkich: 3078
wybranych: 2345
-
Katalog
Filtry wybranego katalogu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: ENDOTHELIAL LAYER
-
Some coatings of high cavitation resistance produced by CO2 laser beam. XIV International Symposium on Gas Flow, Chemical Lasers and High Power Lasers.
PublikacjaPrzedstawiono wyniki badań odporności kawitacyjnej stali 2H13, 45 i żelaza Armco po laserowym stopowaniu ich powierzchni różnymi kompozycjami proszków Co, Mo, Ni, Mn i Cr, Ti. Wykazano różne własności kawitacyjne otrzymanych warstw w zależności od otrzymanej mikrostruktury.
-
Wpływ zawartości wolframu na własności warstw na bazie kobaltu napawanych plazmowo.The influence of tungsten amount on the PTA cobalt base layers property.
PublikacjaW pracy przeanalizowano podobieństwa i różnice między warstwami napawanymi plazmowo z wykorzystaniem proszków na bazie kobaltu o różnych zawartościach wolframu. Morfologia warstw i rozkład pierwiastków dla obydwu warstw jest analogiczna. Stwierdzono wyższą twardość warstw wykonanych z proszku o wyższej zawartości wolframu.
-
Określenie szybkości korozji stopu AlSi13Mg1CuNi nadtopionego laserowo w warunkach kriogenicznych = Corrosion rate determination of AlSi13Mg1CuNi alloy laser remelted at cryogenic conditions
PublikacjaW pracy przedstawiono wyniki badania szybkości korozji stopu AlSi13Mg1CuNi nadtopionego laserowo w warunkach kriogenicznych. Stop eksponowano w 0,01 M roztworze kwasu siarkowego H2SO4
-
Enhanced photocatalytic activity of transparent carbon nanowall/TiO2 heterostructures
PublikacjaThe synthesis of novel tunable carbon-based nanostructure represented a pivotal point to enhance the efficiency of existing photocatalysts and to extend their applicability to a wider number of sustainable processes. In this letter, we describe a transparent photocatalytic heterostructure by growing boron-doped carbon nanowalls (B-CNWs) on quartz, followed by a simple TiO2 sol-gel deposition. The effect on the thickness and boron-doping...
-
Charge-based deep level transient spectroscopy of B-doped and undoped polycrystalline diamond films
PublikacjaThe undoped and B-doped polycrystalline diamond thin film was synthesized by hot filament chemical vapor deposition and microwave plasma, respectively. The structural characterization was performed by scanning electron microscopy, X-ray diffraction and Raman spectroscopy. The electrical properties of synthesized diamond layer were characterized by dc-conductivity method and charge deep level transient spectroscopy. The B-doped...
-
Chromogeniczne pochodne azoli jako składniki warstw receptorowych czujników optycznych
PublikacjaGłównym celem badań prowadzonych w ramach studium doktoranckiego była synteza oraz badanie właściwości chromogenicznych pochodnych azoli, makrocyklicznych i acyklicznych, jako składników warstw receptorowych czujników optycznych. Otrzymane związki zawierają w swojej strukturze resztę heterocykliczną – azol, który może uczestniczyć w tworzeniu kompleksów z jonami metali ciężkich oraz co najmniej jedno ugrupowanie azowe. Obecność...
-
GaN Nanowire Array for Charge Transfer in Hybrid GaN/P3HT:PC71BM Photovoltaic Heterostructure Fabricated on Silicon
PublikacjaAbstract: We demonstrate that a GaN nanowire array can be used for efficient charge transfer between the organic photovoltaic layer and silicon in a Si/GaN/P3HT:PC71BM inverted hybrid heterostructure. The band alignment of such a material combination is favorable to facilitate exciton dissociation, carrier separation and electron transport into Si. The ordered nature of the GaN array helps to mitigate the intrinsic performance...
-
Mobility Management Solutions for IP Networks Comparative Analysis of IP-based Mobility Protocols and Handover Algorithms Invited Paper
PublikacjaA rapid growth of IP-based networks and services hascreated a vast collection of resources and functionalities availableto users by means of a uniform method of access offered by the IPprotocol. At the same time, advances in the design of mobileelectronic devices allowed them to reach a utility levelcomparable to desktop computers, while still retaining theirmobility advantage. Unfortunately, the base IP protocol does notperform...
-
Resonant Frequencies in Microstrip Structure with Omega Medium Substrate
PublikacjaThe paper presents the research on a rectangular microstrip structure with multilayer substrate containing dielectric and omega medium layers. The effect of pseudochiral medium layer location in the substrate and its thickness on the resonant frequency of the rectangular microstrip structure is investigated. The numerical analysis of investigated structures is based on expansion of electric and magnetic fields. Utilizing the continuity...
-
Stalowe panele sandwicz - nowe możliwości wynikające z zastosowania spawania laserowego = All steel sandwich panels - new possibilities introduced by laser welding techniques
PublikacjaW artykule przedstawiono podstawowe dane na temat stalowych paneli typu sandwicz i technik ich wykonywania. Złącze takie charakteryzuje się specyficznymi własnościami, zdecydowanie odmiennymi od klasycznego połączenia spoiną pachwinową, którego cechy wytrzymałościowe i technologiczne są już dobrze opanowane. W podsumowaniu wykazano, że modelowanie jego geometrii musi być prowadzone na znacznie większym poziomie szczegółowości ze...
-
Automated Analysis of Images from Confocal Laser Scanning Microscopy Applied to Observation of Calcium Channel Subunits in Nerve Cell Model Line Subjected Electroporation and Calcium
Publikacja -
Correction to: Two years later: Is the SARS-CoV-2 pandemic still having an impact on emergency surgery? An international cross-sectional survey among WSES members
Publikacja -
Nanokrystaliczne warstwy ceramiczne otrzymywane metodą pirolizy aerozolowej w tlenkowych ogniwach paliwowych
PublikacjaNiniejsza rozprawa doktorska dotyczy badań materiałów wytwarzanych w postaci cienkich, nanokrystalicznych warstw ceramicznych metodą pirolizy aerozolowej dla zastosowań w tlenkowych ogniwach paliwowych (SOFC). Badane są trzy możliwe obszary zastosowań wytwarzanych warstw tj. osadzanie powłok ochronnych na stalowych interkonektorach dostarczających gazy do elektrody tlenowej, wytwarzanie bariery ochronnej zapobiegającej dyfuzji...
-
Monitoring the curing process of epoxy adhesive using ultrasound and Lamb wave dispersion curves
PublikacjaMonitoring the stiffness of adhesives is a crucial issue when considering the durability andstrength of adhesive joints. While there are many studies conducted on specimens madeonly from adhesive, the problem of curing of an adhesive film in real joints is moderatelyconsidered. This paper presents the monitoring of stiffening of epoxy adhesive using ultra-sound. Ultrasonic pulse velocity method was firstly applied for monitoring...
-
Microstructure and Properties of Electroless Ni-P/Si3N4 Nanocomposite Coatings Deposited on the AW-7075 Aluminum Alloy
PublikacjaThe article presents the results of mechanical and tribological tests of Ni-P/Si3N4 nanocomposite coatings deposited on the AW-7075 aluminum alloy using the chemical reduction method. The influence of the chemical composition on the Vickers microhardness determined by the DSI method was examined. The nanocomposite layers were made of Si3N4 silicon nitride in a polydisperse powder with a particle size ranging from 20 to 25 nm. The...
-
Influence of dispersed phase content on the mechanical properties of electroless nanocomposite Ni-P/Si3N4 and hybrid Ni-P/Si3N4/graphite layers deposited on the AW-7075 alloy.
PublikacjaThe article presents the results of mechanical testing of Ni-P/Si3N4 nanocomposite and hybrid Ni-P/Si3N4/graphite coatings deposited on AW-7075 aluminum alloy using the chemical reduction method. In terms of mechanical testing, microhardness was measured, and surface roughness and adhesion of the coatings to the aluminum substrate were determined using the “scratch test” method. The surface morphology of the deposited layers was...
-
Interaction of SrTi0.65Fe0.35O3-δ with LaNi0.6Fe0.4O3-δ, La0.6Sr0.4Co0.2Fe0.8O3-δ and Ce0.8Gd0.2O2-δ
PublikacjaIron doped strontium titanates SrTi1-xFexO3-δ are perovskites of versatile properties. They can be used in solid oxide fuel cells or high temperature oxygen sensors. Their reactivity with electrolyte materials, cathode buffer layer materials, other cathode materials or current collector layers has not been fully tested. In this study we use X-ray diffraction to check SrTi0.65Fe0.35O3-δ compatibility with Ce0.8Gd0.2O2-δ (used as...
-
Ceria Based Protective Coatings for Steel Interconnects Prepared by Spray Pyrolysis
PublikacjaStainless steels can be used in solid oxide fuel/electrolysis stacks as interconnects. For successful long term operation they require protective coatings, that lower the corrosion rate and block chemical reactions between the interconnect and adjacent layers of the oxygen or the hydrogen electrode. One of the promising coating materials for the hydrogen side is ceria. Using standard sintering techniques, ceria sinters at around...
-
3D modelling of beach topography changes caused by the tombolo phenomenon using terrestrial laser scanning (TLS) and unmanned aerial vehicle (UAV) photogrammetry on the example of the city of Sopot
Publikacja -
Morfologia warstw na bazie kobaltu napawanych plazmowo z zastosowaniem różnych technologii procesu.Morphology of the kobalt base laser produced by PTA method using the different technology.
PublikacjaPrzeanalizowano wpływ różnych parametrów napawania laserowego na morfologię i twardość warstwy otrzymanej z jednego proszku na bazie kobaltu. Stwierdzono różnice zarówno w budowie jak i twardości wytworzonych warstw.
-
Taxonomy of Schemes for Resilient Routing
PublikacjaThis chapter provides a taxonomy of schemes for resilient routing followed by a discussion of their application to contemporary architectures of communication networks. In particular, a general classification of schemes for resilient routing is first presented followed by a description of the reference schemes for IP networks. The chapter in its later part focuses on the representative techniques of resilient routing for a multi-domain...
-
Failure analysis of the exhaust valve face in diesel marine engine
PublikacjaThe exhaust valve from marine diesel engine which was damaged after 2000 hours of service was investigated. In order to prolong the service time the valve face was cladded with cobalt base alloy using laser technique. After failure microstructural and chemical analyses reviled that cladding process was conducted improperly. The chemical composition of the clad layer was far from the designed one and what more completely inhomogeneous....
-
Absorbciâ vodoroda i povedenie vodoroda v slaâh titanovyh silavov s modificirovannoj poverhnost''û = Hydrogen absorption and hydrogen effects in the modified surface layers of Ti alloys
PublikacjaW pracy przedstawiono rezultaty badań absorpcji wodoru w stopach tytanu ze zmodyfikowaną za pomocą metod multipleksowych powierzchnią. W wyniku badań stwierdzono, iż po nadtapianiu laserowym w warunkach kriogenicznych, stopy tytanu wykazuja najwyższą zdolność absorpcji wodoru w wytworzonej warstwie wierzchniej.
-
Effect of tungsten content on the corrosion resisntance of the cobalt base PTA cladding layers = Wpływ zawartości wolframu w stopach kobaltu na odporność korozyjną warstw napawanych plazmowo
PublikacjaBadaniom poddano napawane plazmowo warstwy wytworzone na powierzchni przylgni zaworów wylotowych silnie obciążonych silników Diesla stosowanych w okrętownictwie. Jako materiał do napawania zastosowano trzy rodzaje proszków wykonanych ze stopów na bazie kobaltu i chromu zawierających różne ilości wolframu ( 4.9, 5.3 i 9 % masowych). Wykonane napoiny wielowarstwowe po odpowiednim przygotowaniu poddano działaniu podwyższonej temperatury...
-
Combination of terrestrial laser scanning and UAV photogrammetry for 3D modelling and degradation assessment of heritage building based on a lighting analysis: case study—St. Adalbert Church in Gdansk, Poland
PublikacjaThe construction of the St. Adalbert Church in Gdansk dates to 1310. It is a church of rich history and great historical value, and its care is challenging. In this study, the combination of unmanned aerial vehicle (UAV) photogrammetry and terrestrial laser scanning (TLS) was used to accurately build a 3D model of the church. Together with the collected historical inventory documentation, the historic building information model...
-
Cavitation resistance of OH18N9 steel alloyed with vaidus amount of TiC or Mn by means of laser beam. XIV International Symposium on Gas Flow, Chemical Lasers and High Power Lasers.
PublikacjaPrzedstawiono badania odporności kawitacyjnej stali OH18N9T po laserowym stopowaniu jej powierzchni węglikiem TiC oraz manganem. Wykazano, że wzbogacenie obrabianej stali manganem powoduje przemiany fazowe pod wpływem działania obciążeń kawitacyjnych, co przyczynia się do wzrostu odporności kawitacyjnej. Wzmacnianie stali węglikiem TiC powoduje natomiast zanik zdolności stali do wzmacniania odkształceniowego.
-
Wytwarzanie i modyfikacja powierzchni porowatych struktur tytanowych przeznaczonych na implanty
PublikacjaCelem pracy było wytworzenie stopu Ti-13Nb-13Zr z wykorzystaniem technologii selektywnego topienia laserowego (SLM) oraz jego biofunkcjonalizacja za pomocą utleniania mikrołukowego (MAO), a następnie określenie wpływu parametrów procesowych na właściwości otrzymanych materiałów pod kątem ich zastosowania na implanty. Oceniono wpływ napięcia, natężenia i czasu procesu MAO przeprowadzanego w elektrolicie zawierającym wapń i fosfor...
-
Investigation of low-temperature cracking in newly constructed high-modulus asphalt concrete base course of a motorway pavement
PublikacjaThe paper presents the issue of low-temperature transverse cracks which have developed in newly constructed base courses made of high-modulus asphalt concrete mix (HMAC). Numerous transverse cracks developed in the analysed HMAC base during the winter season before the pavement was actually completed, both at the transverse joint locations and in the areas between them. This had not happened so far on such a scale during road construction...
-
Polymer based thick films - material quality and interface resistance evaluation
PublikacjaThe properties of polymer based thick film layers mede using different resistive pastes and dipping silvers have been studied. The composite of carbon and graphite (C/Gr) conducting particles suspended in different polymer vehicles were used for preparation resistive layers. Interface resistance Rc created between dipping silver (DiAg) contact layer and resistive layer was determined from the surface potential distribution measurements...
-
Hydrogen degradation of pre-oxidized zirconium alloys
PublikacjaThe presence of the oxide layers on Zr alloys may retard or enhance the hydrogen entry and material degradation, depending on the layer features. This research has been aimed to determine the effects of pre-oxidation of the Zircaloy-2 alloy at a different temperature on hydrogen degradation. The specimens were oxidised in laboratory air at 350°C, 700°C, and 900°C. After, some samples were tensed at 10-5 strain rate and simultaneously...
-
Steady magnetohydrodynamic flow in a diverging channel with suction or blowing
PublikacjaAn analysis is made of steady two-dimensional divergent flow of an electrically conducting incompressible viscous fluid in a channel formed by two non-parallel walls, the flow being caused by a source of fluid volume at the intersection of the walls. The fluid is permeated by a magnetic field produced by an electric current along the line of intersection of the channel walls. The walls are porous and subjected to either suction...
-
Optical and chemical characterization of thin TiNx films deposited by DC-magnetron sputtering
PublikacjaThin titanium nitride (tinx) films were deposited on silicon substrates by means of a reactive dc-magnetron plasma. Layers were synthesized under various conditions of discharge power and nitrogen flows in two operation modes of the magnetron (the so-called "balanced" and "unbalanced" modes). The optical constants of the tinx films were investigated by spectroscopic ellipsometry (se). X-ray photoelectron spectroscopy (xps) was...
-
The use of thin diamond films in fiber optic low-coherence interferometers”
PublikacjaIn this paper we present the use of thin diamond films in fiber-optic low-coherence interferometers. Two kinds of diamond surfaces were used: undoped diamond film and boron-doped diamond film. They were deposited on glass plates as well as silicon layers. A conventionally used mirror was used as a reference layer. Diamond films were deposited using Microwave Plasma Enhanced Chemical Vapour Deposition (μPE CVD) system. Measurements...
-
Effects of thermal history on the performance of low-temperature solid oxide fuel cells with Sm0.2Ce0.8O2-δ electrolyte and LiNi0.81Co0.15Al0.04O2 electrodes
PublikacjaIn this study, low-temperature solid oxide fuel cells with an ∼560 μm thick Sm0.2Ce0.8O2−δ (SDC) electrolyte and ∼890 μm thick LiNi0.81Co0.15Al0.04O2−δ (NCAL) electrodes are constructed and characterized under three experimental conditions. The cell with an NCAL cathode pre-reduced under an H2 atmosphere at 550 °C presents the best electrochemical performance. This is ascribed to facts that the reduction reaction generating Ni–Co...
-
Incorporating Iris, Fingerprint and Face Biometric for Fraud Prevention in e-Passports Using Fuzzy Vault
PublikacjaA unified frame work which provides a higher security level to e-passports is proposed. This framework integrates face, iris and fingerprint images. It involves three layers of security: the first layer maps a biometric image to another biometric image which is called biostego image. Three mapping schemes are proposed: the first scheme maps single biometric image to single biostego image, the second scheme maps dual biometric images...
-
Implementation of Hierarchical Control of Drinking Water Supply System
PublikacjaThe paper presents the outline of the didactical project of a complex computer controlled system realized by the first degree students of the Automatics and Robotics on the Faculty of Electrical and Control Engineering (FoEaCE) in Gdansk University of Technology (GUT). The synthesis, implementation and analysis of a multilayer hierarchical control system for drinking water supply system (DWSS) are main topics of that project. The...
-
Deposition and Electrical and Structural Properties of La0.6Sr0.4CoO3 Thin Films for Application in High-Temperature Electrochemical Cells
PublikacjaLow-temperature deposition of electroceramic thin films allows the construction of new devices and their integration with existing large-scale fabrication methods. Developing a suitable low-cost deposition method is important to further advance the development of microdevices. In this work, we deposited a 1-lm-thick La0.6Sr0.4CoO3d (LSC) perovskite with high electrical conductivity on sapphire substrates at 400C and analyzed its...
-
Cost-effective methods of fabricating thin rare-earth element layers on SOC interconnects based on low-chromium ferritic stainless steel and exposed to air, humidified air or humidified hydrogen atmospheres
PublikacjaMost oxidation studies involving interconnects are conducted in air under isothermal conditions, but during real-life solid oxide cell (SOC) operation, cells are also exposed a mixture of hydrogen and water vapor. For this study, an Fe–16Cr low-chromium ferritic stainless steel was coated with different reactive element oxides – Gd2O3, CeO2, Ce0.9Y0.1O2 – using an array of methods: dip coating, electrodeposition and spray pyrolysis....
-
Role of bead sequence in underwater welding
PublikacjaThis paper presents examinations of the role of the bead sequence in underwater welding. Two specimens of wet welded layers made by covered electrodes with the use of normalized S355G10+N steel were welded by a reasonable bead sequence. For each specimen, metallographic macro- and micro-scopic tests were done. Then, Vickers HV10 hardness measurements were conducted for each pad weld in the welded layer. The results show that welding...
-
Structural Design and Sensitivity Analysis of Semi-Rigid Pavement of a Motorway
PublikacjaThis paper presents application of mechanistic-empirical methods in design of semi-rigid pavement for a section of a motorway in Poland. The stage construction was assumed. Three fatigue criteria were applied in the design. For asphalt fatigue cracking and subgrade soil the criteria from the Asphalt Institute (1981) were applied. For fatigue cracking of cement stabilized bases the Dempsey (1984) and De Beer (1992) criteria were...
-
X-ray photoelectron spectroscopy, Raman and photoluminescence studies on formation of defects in Cu:ZnO thin films and its role in nonlinear optical features
Publikacja -
Experimental generation of complex noisy photonic entanglement
PublikacjaWe present an experimental scheme based on spontaneous parametric down-conversion to produce multiple-photon pairs in maximally entangled polarization states using an arrangement of two type-I nonlinear crystals. By introducing correlated polarization noise in the paths of the generated photons we prepare mixed-entangled states whose properties illustrate fundamental results obtained recently in quantum information theory, in particular those...
-
Surface Structure of Components Created by Stereolitography
PublikacjaStereolithography is an additive rapid prototyping method. This method is based on the principle of solidifying a liquid photopolymer (resin) by laser radiation. Models obtained with this method are characterized by a specific surface structure called “stairstep effect”. It causes that, the surface should be processed by additional finishing (postprocessing). To minimize the additional machining process, the model should be set...
-
Novel MNZ-type microwave sensor for testing magnetodielectric materials
PublikacjaA novel microwave sensor with the mu-near-zero (MNZ) property is proposed for testing magnetodielectric material at 4.5 GHz. The sensor has a double-layer design consisting of a microstrip line and a metal strip with vias on layers 1 and 2, respectively. The proposed sensor can detect a unit change in relative permittivity and relative permeability with a difference in the operating frequency of 45 MHz and 78 MHz, respectively....
-
CGO FILMS ON YSZ ELECTROLYTE FABRICATED BY SPRAY PYROLYSIS FOR SOFC
PublikacjaINTRODUCTION Solid oxide fuel cells are one of the fastest developing energy converters. The advancement introduced by research community provides steady state progress is stability and performance of the fuel cells. Significant influence on the cell’s performance and stability is related to cell design. The simplest design just consists of an anode, a solid electrolyte and a cathode. However, in order to improve the properties,...
-
The effect of the exposure-in-oil on the contact of the polymers forming sliding layers in hydrodynamic bearings. Wpływ ekspozycji w oleju na kąt zwilżania polimerów stosowanych na warstwy ślizgowe w łożyskach hydrodynamicznych.
PublikacjaPolimery stosowane jako warstwy ślizgowe w hydrodynamicznych łożyskach wzdłużnych to zazwyczaj tworzywa termoplastyczne charakteryzujące się relatywnie wysokimi wartościami kątów zwilżania w porównaniu z metalami. Metale, w tym również Babbitt czy inne stopy łożyskowe, cechują niskie wartości kątów zwilżania. Im niższy kąt, tym powierzchnia lepiej się zwilża. Tworzywa sztuczne wykorzystywane w węzłach tribologicznych mających zapewnić...
-
Featuring Semitransparent p–i–n Perovskite Solar Cells for High-Efficiency Four-Terminal/Silicon Tandem Solar Cells
PublikacjaTwo issues need to be resolved when fabricating p–i–n semitransparent perovskite solar cells (ST-PVSCs) for four-terminal (4 T) perovskite/silicon tandem solar cells: 1) damage to the underlying absorber (MAPbI3), electron transporting layer ([6,6]-phenyl-C61-butyric acid methyl ester, PCBM), and work function (WF) modifier (polyethylenimine, PEI), resulting from the harsh sputtering conditions for the transparent electrodes (TEs)...
-
Enhancing Availability for Critical Services
PublikacjaTraditional approaches to provide classes of resilient service take the physical network availability as an input and then deploy redundancy and restoration techniques at various layers, often without full knowledge of mappings between layers. This makes it hard (and often inefficient) to ensure the high availability required by critical services which are typically a small fraction of the total traffic. Here, the innovative technique...
-
Oxidation and hydrogen behavior in Zr-2Mn alloy
PublikacjaThe purpose of the present research was to determine the oxidation and hydrogenation behavior in the new Zr-2Mn alloy. The oxidation of alloy was performed at temperatures between 350°C and 900°C for 30 minutes. The hydrogen charging was made for 72 h at a current density 80 mA/cm2. The charged samples were heat treated at 400°C for 4 h to obtain a uniform hydrogen profile content across the sample. The oxidation resulted in an...
-
Mobility management solutions for current IP and future networks
PublikacjaEnormous progress in the design of portable electronic devices allowed them to reach a utility level comparable to desktop computers, while still retaining their mobility advantage. At the same time new multimedia services and applications are available for IP users. Unfortunately, the performance of base IP protocol is not satisfactory in mobile environments, due to lack of handover support and higher layer mobility management...