Wyszukiwarka
Filtry
wszystkich: 445
wybranych: 392
-
Katalog
Filtry wybranego katalogu
Wyniki wyszukiwania dla: DISTORTION COMPENSATION
-
Effect of adhesive compliance in the assessment of soft adhesives with the wedge test
PublikacjaWedge tests are usually analysed assuming that the free, unbonded members may be treated as encastré cantilever beams. However, if the adhesive layer is sufficiently flexible (e.g., due to low elastic modulus), then significant strain in the bonded region may occur and lead to modification of the behaviour outside this region. Using in conjunction a sensitive strain gauge method on asymmetric wedge tests and a mathematical analysis...
-
Current divider-based nanosecond high current pulse measuring systems
PublikacjaThis paper presents the analysis of the new approach to the measurement methodology of significant values (in order of hundreds of kA) and huge steepness (in order of MA/μs) current pulses based on current dividers along with a comparison of the various types transducers suitability in measuring systems with such extreme parameters. Such dividers are used to extend the measurement ranges of current transducers with limited current...
-
A new approach to active noise and vibration control - [Part I: the known frequency case]
PublikacjaThis paper presents a new approach to rejection of complex-valued sinusoidal disturbances acting at the output of a discrete-time stable linear plant with unknown dynamics. It is assumed that the frequency of the sinusoidal disturbance is known, and that the output signal is contaminated with wideband measurement noise. The disturbance rejection control rule is first derived and analyzed for a nominal plant model, different from...
-
Application of OFDM technique to underwater acoustic data transmission
PublikacjaPerformances of underwater acoustic communication (UAC) digital systems are strongly related to specific transmission properties of the underwater channel. Depending on the characteristics of the channel, an architecture and modulation techniques are usually implemented that are known as reliable solutions for data transmission in difficult radio channels. The OFDM technique seems to be the most promising nowadays. The parameters...
-
Wind Turbines Modeling as the Tool for Developing Algorithms of Processing their Video Recordings
PublikacjaIn the real world, many factors exist disturbing observation of the examined phenomena and causing various noises and distortions in recorded signals. It very often makes it difficult or even impossible to optimize various signal processing algorithms, through finding appropriate parameters. In this paper, we show an application, that retrieves wind turbine rotor speed from recorded video. Next, we describe the process of reduction...
-
Wind Turbines Modeling as the Tool for Developing Algorithms of Processing their Video Recordings
PublikacjaIn the real world, many factors exist disturbing observation of the examined phenomena and causing various noises and distortions in recorded signals. It very often makes it difficult or even impossible to optimize various signal processing algorithms, through finding appropriate parameters. In this paper, we show an application, that retrieves wind turbine rotor speed from recorded video. Next, we describe the process of reduction...
-
Isolation and structure of a covalent cross-link adduct between mitomycin C and DNA
PublikacjaA DNA cross-link adduct of the antitumor agent mitomycin C (MC) to DNA has been isolated and characterized; the results provide direct proof for bifunctional alkylation of DNA by MC. Exposure of MC to Micrococcus luteus DNA under reductive conditions and subsequent nuclease digestion yielded adducts formed between MC and deoxyguanosine residues. In addition to the two known monoadducts, a bisadduct was obtained. Reductive MC activation...
-
Current harmonic controller in multiple reference frames for series active power filter integrated with 18-pulse diode rectifier
PublikacjaThe paper presents the control system and selected results of experimental tests of the AC/DC power converter consisting of an 18-pulse diode rectifier based on coupled reactors and a serial active power filter. Proportional integral controllers with decoupling components are implemented in multiple reference frames for selective line current harmonic suppression. The regulator is provided with a backtracking anti-windup mechanism...
-
A low-voltage CMOS negative impedance converter for analogue filtering applications
PublikacjaLow-voltage high-frequency continuous-time filters are still required in many applications and are the subject of continuing research. There are many techniques to realize integrated filters, including OTA C, Opamp RC and MOSFET-C-Opamp. The latter two show high dynamic range at low supply voltage, but their frequency operating range is usually limited to several megahertz. Transconductance filters are dedicated to higher frequencies....
-
Multiple output differential OTA with linearizing bulk-driven active-error feedback loop for continuous-time filter applications
PublikacjaA CMOS circuit realization of a highly linear multiple-output differential operational transconductance amplifier (OTA) has been proposed. The presented approach exploits a differential pair as an input stage with both the gate and the bulk terminals as signal ports. For the proposed OTA, improved linearity is obtained by means of the active-error feedback loop operating at the bulk terminals of the input stage. SPICE simulations...
-
Hysteresis curves for some periodic and aperiodic perturbations in magnetosonic flow
PublikacjaA thermodynamic relation between perturbations of pressure and mass density in the magnetohydrodynamic flow is theoretically studied. Planar magnetohydrodynamic perturbations with the wave vector, which forms a constant angle with the equilibrium magnetic field, are under study. The theory considers thermal conduction of a plasma and the deviation from adiabaticity of a flow due to some kind of heating–cooling function. It also...
-
Możliwości sterowania mocą bierną elektrowni wiatrowej : Reactive power control methods in wind parks
PublikacjaReferat poświęcony jest zagadnieniu sterowania mocą bierną w elektrowniach wiatrowych. W pierwszej części referatu opisano tło problemu sterowania mocą bierną w parkach wiatrowych, podano powody, dla których moc bierna powinna podlegać regulacji oraz zarysowano metody, które mogą być do niej użyte. W celu sprawdzenia proponowanych metod kompensacji, zbudowano model matematyczny elektrowni wiatrowej, którego poszczególne elementy...
-
Wet H2S corrosion and degradation of pipeline in amine regeneration system
PublikacjaThe paper presents the results of NDT examinations, metallographic tests and risk assessment of degradation related to corrosion of amine regeneration unit in a desulphurisation system. Intensive corrosion resulting from acid gases environment upon water condensation causes perforation of the pipeline. Detailed analysis reveals cracking related to the mechanism of wet H2S. Hydrogen penetration, resulting from the wet H2S process,...
-
On ''cheap smoothing'' opportunities in identification of time-varying systems
PublikacjaIn certain applications of nonstationary system identification the model-based decisions can be postponed, i.e. executed with a delay. This allows one to incorporate into the identification process not only the currently available information, but also a number of ''future'' data points. The resulting estimation schemes, which involve smoothing, are not causal. Despite the possible performance improvements, the existing smoothing...
-
Effects of Bromine Doping on the Structural Properties and Band Gap of CH3NH3Pb(I1–xBrx)3 Perovskite
PublikacjaAn experimental and theoretical study is reported to investigate the influence of bromine doping on CH3NH3Pb(I1−xBrx)3 perovskite for Br compositions ranging from x = 0 to x = 0.1, in which the material remains in the tetragonal phase. The experimental band gap is deduced from UV−vis absorption spectroscopy and displays a linear behavior as a function of bromine concentration. Density functional theory calculations are performed...
-
The In-Depth Studies of Pulsed UV Laser-Modified TiO2 Nanotubes: The Influence of Geometry, Crystallinity, and Processing Parameters
PublikacjaThe laser processing of the titania nanotubes has been investigated in terms of morphology, structure, and optical properties of the obtained material. The length of the nanotubes and crystallinity, as well as the atmosphere of the laser treatment, were taken into account. The degree of changes of the initial geometry of nanotubes were checked by means of scanning electron microscopy, which visualizes both the surface and the cross-section....
-
Selective Harmonic Elimination PWM For a Cascaded Multi-level Inverter
PublikacjaThis paper deals with the selective harmonic elimination pulse width modulation (SHE-PWM) technique. This technique is used for the elimination of selected dominant low order harmonics in the multi-level inverter output voltage. The presence of these harmonics is the essential drawback of such kind of inverters; especially when it is used for the control of different AC drivers. The SHE-PWM is based...
-
Study of the Influence of Heat Convection Coefficient on Predicted Performance of a Large Tilting-Pad Thrust Bearing
PublikacjaPart of the heat generated by the shearing of the lubricating film during operation of a hydrodynamic bearing is transferred to the bearing components. In the case of the pad, which is usually fully submerged in the lubricating oil, heat is further transferred at the pad free walls to the oil by convection. This mechanism causes a thermal gradient in a pad and, consequently, its thermal deflection. In large hydrodynamic thrust...
-
Using wavelet techniques for multibeam sonar bathymetry data compression
PublikacjaMultibeam sonars are widely used in applications like high resolution bathymetry measurements or underwater object imaging. One of the significant problems in multibeam sensing of the marine environment is large amount of data which must be transmitted from the sonar processing unit to an operator station using a limited bit rate channel. For instance, such a situation would be in the case when the multibeam sonar was mounted on...
-
On the compression of multibeam sonar raw bathymetry data
PublikacjaMultibeam sonars are widely used in applications like high resolution bathymetry measurements or underwater object imaging. One of the significant problems in multibeam sensing of the marine environment is large amount of data which must be transmitted from the sonar processing unit to an operator station using a limited bit rate channel. For instance, such a situation would be in the case when the multibeam sonar was mounted on...
-
Iterative‐recursive estimation of parameters of regression models with resistance to outliers on practical examples
PublikacjaHere, identification of processes and systems in the sense of the least sum of absolute values is taken into consideration. The respective absolute value estimators are recognised as exceptionally insensitive to large measurement faults or other defects in the processed data, whereas the classical least squares procedure appears to be completely impractical for processing the data contaminated with such parasitic distortions. Since...
-
Signal filtering method of the fast-varying diesel exhaust gas temperature
PublikacjaThe paper presents the problem of the impact of external distortions originating on laboratory test stands on the results of measurements of fast-varying diesel exhaust gas temperature. It has been stressed how significant the aspect of the test stand adaptation is during an experiment to ensure the smallest possible impact. This paper, however, focuses on the methods of mathematical processing of a signal recorded during experimental...
-
Fast bubble dynamics and sizing
PublikacjaSingle bubble sizing is usually performed by measuring the resonant bubble response using the Dual Frequency Ultrasound Method. However, in practice, the use of millisecond-duration chirp-like waves yields nonlinear distortions of the bubble oscillations. In comparison with the resonant curve obtained under harmonic excitation, it was observed that the bubble dynamic response shifted by up to 20 percent of the resonant frequency...
-
Disruption of the communication process on the example of ALEP-PL web application
PublikacjaBy creating a dedicated web service, such as the presented ALEP-PL solution, you can not assume that its users have suffcient knowledge of the energy sector. This application is dedicated to the local energy planning. The ALEP-PL makes it easier to incorporate in the planning of key players in the local energy market. This group of ALEP-PL users represents mainly the ocials of energy companies and specialist offcers. In the paper...
-
Periodic Properties of 1D FE Discrete Models in High Frequency Dynamics
PublikacjaFinite element discrete models of various engineering 1D structures may be considered as structures of certain periodic characteristics. The source of this periodicity comes from the discontinuity of stress/strain field between the elements. This behaviour remains unnoticeable, when low frequency dynamics of these structures is investigated. At high frequency regimes, however, its influence may be strong enough to dominate calculated...
-
Broken rotor bar impact on sensorless control of induction machine
PublikacjaThe aim of the research is analysis of the sensorless control system of induction machine with broken rotor for diagnostic purposes. Increasing popularity of sensorless controlled variable speed drives requires research in area of reliability, range of stable operation, fault symptoms and application of diagnosis methods. T transformation (Cunha et al.,2003) used for conversion of instantaneous rotor currents electrical circuit...
-
Control of the wind turbine generator
PublikacjaWind power system consists of two main parts: wind turbine and electrical generator. Wind turbine converts the energy of the flowing air into mechanical energy, next generator converts this energy into electrical energy that is sent to the power system. These two processes should be realized with maximum efficiency and the following requirements for the control system can be formulated: opti-mal wind power conversion, compensation...
-
A concept of Signal Equalization Method Based on Music Genre and the Listener's Room Characteristics
PublikacjaA research study that investigates the influence of the room acoustics environment on the frequency characteristic of the audio signal playback is presented. First, a novel spectral equalization method of the room acoustic conditions is introduced. On the basis of the frequency response of the room, a system for room acoustics compensation based on eight-band equalizer is proposed. The system settings depend on music genre. In...
-
Rain Water: Atmospheric Deposition
PublikacjaWater is transferred from the atmosphere to the land surface mainly via various forms of atmospheric precipitation; however, the contribution of surface condensation/deposition (e.g., dew, hoar frost, occult precipitation) should not be neglected. Rainwater and liquid deposits (dew, hoar frost, rime) are components of the physical and geographical environment that are easily assimilated and transported. Thus, they are generally...
-
Thermodynamic analysis of the double Brayton cycle with the use of oxy combustion and capture of CO2
PublikacjaIn this paper, thermodynamic analysis of a proposed innovative double Brayton cycle with the use of oxy combustion and capture of CO2, is presented. For that purpose, the computation flow mechanics (CFM) approach has been developed. The double Brayton cycle (DBC) consists of primary Brayton and secondary inverse Brayton cycle. Inversion means that the role of the compressor and the gas turbine is changed and firstly we have expansion...
-
Analiza ograniczeń technologicznych systemów lokalizacji inercyjnej
PublikacjaW artykule opisano kluczowe ograniczenia technologiczne zmniejszające dokładność inercyjnych systemów lokalizacyjnych. Każdy z czynników został przedstawiony w kontekście swego źródła oraz wpływu na proces lokalizacyjny. Dodatkowo w artykule zawarto opis metod kompensacji błędów występujących w procesie lokalizacji inercyjnej. W treści artykułu analizie poddano rozwiązania obecne w systemach lokalizacji inercyjnej dla wolno poruszających...
-
Enhanced Mechanical and Electromechanical Properties of Compositionally Complex Zirconia Zr1–x(Gd1/5Pr1/5Nd1/5Sm1/5Y1/5)xO2−δ Ceramics
PublikacjaCompositionally complex oxides (CCOs) or high-entropy oxides (HEOs) are new multi-element oxides with unexplored physical and functional properties. In this work, we report fluorite structure derived compositionally complex zirconia with composition Zr1- x(Gd1/5Pr1/5Nd1/5Sm1/5Y1/5)xO2-δ (x = 0.1 and 0.2) synthesized in solid-state reaction route and sintered via hot pressing at 1350 °C. We explore the evolution of these oxides'...
-
Investigation of Noise Threats and Their Impact on Hearing in Selected Schools
PublikacjaNoise measurements conducted in selected schools in Gdansk area are presented in this paper. The main aim of this research was to determine noise threats at schools. Some objective measurements of the acoustic climate were performed employing a noise monitoring station engineered at the Multimedia System Department, Gdansk University of Technology. Simultaneously, subjective noise annoyance examinations were carried out among pupils...
-
Investigation of noise threats and their impact on hearing in selected schools - a pilot study.
PublikacjaNoise measurements conducted in selected schools in Gdansk area are presented in this paper. The main aim of this research was to determine noise threats at schools. Some objective measurements of the acoustic climate were performed employing a noise monitoring station engineered at the Multimedia System Department, Gdansk University of Technology. Simultaneously, subjective noise annoyance examinations were carried out among pupils...
-
A benchmark for particle shape dependence
PublikacjaParticle shape is a major parameter for the space-filling and strength properties of granular materials. For a systematic investigation of shape effect, a numerical benchmark test was set up within a collaborative group using different numerical methods and particles of various shape characteristics such as elongation, angularity and nonconvexity. Extensive 2D shear simulations were performed in this framework and the shear strength...
-
Particle shape dependence in 2D granular media
PublikacjaParticle shape is a key to the space-filling and strength properties of granular matter. We consider a shape parameter eta describing the degree of distortion from a perfectly spherical shape. Encompassing most specific shape characteristics such as elongation, angularity and non-convexity, eta is a low-order but generic parameter that we used in a numerical benchmark test for a systematic investigation of shape dependence in sheared...
-
Robustness in Compressed Neural Networks for Object Detection
PublikacjaModel compression techniques allow to significantly reduce the computational cost associated with data processing by deep neural networks with only a minor decrease in average accuracy. Simultaneously, reducing the model size may have a large effect on noisy cases or objects belonging to less frequent classes. It is a crucial problem from the perspective of the models' safety, especially for object detection in the autonomous driving...
-
Analysis of cyclone separator solutions depending on spray ejector condenser conditions
PublikacjaThe core design strategy for minimizing CO2 emissions in gas power plant entails combining a spray ejector condenser (SEC) and separator to accomplish steam condensation and CO2 purification. This innovative process involves direct-contact condensation of steam with CO2, facilitated by interaction with a subcooled water spray, along with a cyclone separator mechanism intended for generating pure CO2. The investigation of the SEC...
-
Depressive symptoms in elderly people participating in University of the Third Age and residents of Nursing Homes: The role of optimism and acceptance of passing
PublikacjaThe elderly age group needs particular support in preventing development of depressive symptoms, among others, due to the prospect of passing. This group is heterogenous in terms of characteristics of ways of spending leisure time, which, as an important aspect of everyday life affecting the quality of interpersonal relationships and well-being, might be related to the level of their depressive symptoms. The aim of this study...
-
Three phase transient model of wet coal pyrolysis
PublikacjaA one-dimensional transient mathematical model was developed to describe the thermal and flow phenomena during coal pyrolysis in a coke oven. The model was solved numerically using partly implicit methods for gas flow and heat transfer problems. It was successfully validated with industrial-scale measurements of temperature change in the middle-plane of the coke oven chamber. The evolution of temperature and pressure, distributions...
-
Performance of the very high-temperature heat pump with low GWP working fluids
PublikacjaTraditional heat pumps are a very attractive pro-ecological solutions for a number of applications, including providing of heating or heat recovery from industrial processes. The application range of heat pumps could be greatly enlarged when the operating temperature would be increased to 130-150°C and/or the temperature lift can be increased to 50-100 K. In the paper, the very high temperature vapour-compressor based single stage...
-
Ruchotwórczość wielkopowierzchniowych obiektów handlowych trzeciej generacji na przykładzie Trójmiasta
PublikacjaWielkopowierzchniowe obiekty (handlowe, usługowe itp.) generują ruch o dużych natężeniach, które często przekraczają możliwości przepustowe przyległego układu ulicznego. Wpływają w ten sposób na znaczne pogorszenie się warunków ruchu w najbliższym otoczeniu obiektu i zakłócenia w prawidłowym funkcjonowaniu systemu transportowego miasta. Wobec braku polskich doświadczeń konieczne jest badanie wpływu wybranych czynników demograficznych,...
-
Nonlinear properties of the Gotland Deep – Baltic Sea
PublikacjaThe properties of the nonlinear phenomenon in water, including sea water, have been well known for many decades. The feature of the non homogeneous distribution of the speed of sound along the depth of the sea is very interesting from the physical and technical point of view. It is important especially in the observation of underwater area by means of acoustical method ( Grelowska et al ., 2013; 2014). The observation of the underwater...
-
Assessment of particular abdominal aorta section extraction from contrast-enhanced computed tomography angiography
PublikacjaThe aim of this work is to improve the accuracy of extraction of a particular abdominal aorta section and to reduce the distortion in three-dimensional Computed Tomography Angiography (CTA) images. Imaging modality and quality plays crucial role in the medical diagnostic process, thus ensuring high quality of images is essential at every stage of acquisition and processing.Noise is defined as a disturbance of the image quality...
-
A New Approach to the PWM Modulation for the Multiphase Matrix Converters Supplying Loads with Open-End Winding.
PublikacjaThis article presents three variants of the Pulse Width Modulation (PWM) for the Double Square Multiphase type Conventional Matrix Converters (DSM-CMC) supplying loads with the open-end winding. The first variant of PWM offers the ability to obtain zero value of the common-mode voltage at the load's terminals and applies only six switches within the modulation period. The second proposal archives for less Total Harmonic Distortion...
-
Thin-walled cross section shape influence on steel member resistance.
PublikacjaThis work describes why trending thin-walled technology is achieving popularity in steel construction sector. A purpose of this article is to present the influence of the cold-formed element cross-section shape on an axial compression and a bending moment resistance. The authors have considered four different shapes assuming constant section area and thickness. Calculations were based on three different steel grades taking into...
-
Radar technique in application of interlayer identification connections
PublikacjaOne of important issues in pavement construction is to ensure that layers applied directly one on top of the other make up a continuous whole and form an integral construction complex. An appropriate interlayer connection plays here significant role ensuring proper transmission of distortions generated by wheels of vehicles to lower layers and preventing water penetration between the layers. In case of damaged pavements where lack...
-
A novel (Ti/Ce)UiO-X MOFs@TiO2 heterojunction for enhanced photocatalytic performance: Boosting via Ce4+/Ce3+ and Ti4+/Ti3+ redox mediators
PublikacjaTitanium-substituted cerium-oxo-based UiO MOFs with terephthalate linkers modified by various groups (–Br, –NH2, –NO2) or their derivatives (N-heterocyclic or biphenyl groups) were combined with titanium dioxide in a multistep route to obtain a core-shell-like architecture. DFT simulations showed that Ce- and bimetallic Ti/Ce- MOFs exhibited different charge compensation. Extended characterization revealed the formation of heterojunctions between...
-
Comparative study of operation of condensing and traditional boilers equipped with ORC module for electricity generation
PublikacjaThe study analyzed the operation of the "traditional" boiler equipped with the ORC module as the similar arrangement but with the condensing boiler. In the case of a conventional boiler there is noted a greater fuel consumption and the greater power generated than in the case of the unit with the condensing boiler. Postulated is the indicator in the form of a ratio of turbine power to the mass flow rate of fuel, which in turn gives...
-
ASYNCHRONICZNE METODY RADIOLOKALIZACYJNE
PublikacjaW pracy przedstawiono wybrane problemy lokalizowania obiektów w asynchronicznych sieciach radiowych. W pierwszej kolejności zostały zdefiniowane kryteria jakościowe do oceny efektywności pracy opracowanych metod oraz przedstawiono model symulacyjny, który został użyty do badań. W kolejnych trzech rozdziałach szczegółowo opisano trzy oryginalne asynchroniczne metody radiolokalizacyjne w różnych wariantach. Przeprowadzono analizę...