Filtry
wszystkich: 1346
wybranych: 910
Wyniki wyszukiwania dla: NITROUS OXIDE
-
Electro-optical transducer based on indium-tin-oxide-coated optical fiber for analysis of ionized media
PublikacjaThe paper introduces a concept of an optical fiber based electro-optical transducer for monitoring of ionized media, such as low-temperature plasma. It utilizes optical fiber with a section of a core coated with tailored indium tin oxide (ITO) thin film and thus combines the optical phenomena of lossy-mode resonance (LMR) with the electrostatic probe. ITO is an optically transparent and electrically conductive material and if its...
-
Crystalline Silicon (c-Si)-Based Tunnel Oxide Passivated Contact (TOPCon) Solar Cells: A Review
PublikacjaContact selectivity is a key parameter for enhancing and improving the power conversion efficiency (PCE) of crystalline silicon (c-Si)-based solar cells. Carrier selective contacts (CSC) are the key technology which has the potential to achieve a higher PCE for c-Si-based solar cells closer to their theoretical efficiency limit. A recent and state-of-the-art approach in this domain is the tunnel oxide passivated contact (TOPCon)...
-
Nanostructured graphene oxide enriched with metallic nanoparticles as a biointerface to enhance cell adhesion through mechanosensory modifications
Publikacja -
Equilibrium, kinetic and thermodynamic studies on adsorption of cationic dyes from aqueous solutions using graphene oxide
Publikacja -
The cellulose fibers functionalized with star-like zinc oxide nanoparticles with boosted antibacterial performance for hygienic products
Publikacja -
Reduced graphene oxide nanocomposites with different diameters and crystallinity of TiO2 nanoparticles – synthesis, characterization and photocatalytic activity
Publikacja -
Influence of reduction process on the structural and mechanical properties of (Pb,Bi)-(Si,Ge)-O oxide glasses
PublikacjaThe effect of the reduction process in H2 at 380 °C on the microstructure and elemental composition of a glass Bi0.4Pb0.2Si0.4Ox has been investigated. It has been shown that after reduction a clearly separated top layer with a thickness of approx. 50 µm was formed on the surface of the sample. This layer is depleted of oxygen and has higher electrical conductivity than the interior of the glass. It has also been found that some...
-
Structure and thermoelectric properties of Cs-Bi-Te alloys fabricated by different routes of reduction of oxide reagents
PublikacjaCesium-bismuth-telluride polycrystalline materials were fabricated using a cost-effective method based on a reduction of oxide reagents, leading to a production of a material with good thermoelectric properties. Several samples with various initial stoichiometry were prepared by melting of oxide powders at 1050 °C, quenching, milling to powders and then reducing in pure hydrogen at 400 °C. Another concept was to obtain the CsBi4Te6...
-
Synthesis of isotactic polypropylene- block -polystyrene block copolymers as compatibilizers for isotactic polypropylene/polyphenylene oxide blends
PublikacjaPoly(2,6-dimethyl-1,4-phenylene oxide) (PPO) and isotactic polypropylene (iPP) are highly incompatible and consequently their uncompatibilized blends are quite brittle regardless of the molecular weights and ductility of the individual components. Isotactic polypropylene-polystyrene block copolymers, to be applied as compatibilizers for a broad range of PPO/iPP blend compositions, were prepared by mechanism transformation from...
-
Determination of pseudocapacitance chan ges of nickel oxide NiO electrode with use of dynamic electrochemical impedancje spectroscopy
PublikacjaThe electrochemical capacitors (ECs) are attractive energy storage devices which can be applied in many electronic products (e.g., cameras, laptops, cell phones) or hybrid electric vehicles (HEV). The energy storage in ECs is based on capacitive (the electrical double layer charging/discharging) and pseudocapacitive (additional charge provided by faradic reaction) phenomena. Considering the electrodes exhibiting pseudocapacitance,...
-
Inhibition of amyloid fibril formation of hen egg white lysozyme by trimethylamine N-oxide at low pH
PublikacjaIn vitro inhibition of the formation of fibrous aggregates of proteins (amyloids) has gained increasing attention due to the number of diseases associated with protein misfolding and fibrillation. An interesting group of compounds for which pronounced activity against this phenomenon can be expected consists of low molecular weight substances (osmolytes) which have the ability to change protein stability. Here we investigate the...
-
Data analysis of FTIR spectra for study of outlet gases of Solid Oxide Fuel Cells fuelled by biogas
PublikacjaW pracy przedstawiono system umożliwiający połączenie spektroskopii FTIR z specjalnie zaprojektowanym oprogramowaniem w celu uzyskania informacji o stężeniach gazów wylotowych z ogniw paliwowych SOFC. Przebadane zostały główne produkty reformingu biogazu: tlenek węgla, dwutlenek węgla, metan oraz wodór. Opisane oprogramowanie umożliwia w prosty i szybki sposób uzyskanie informacji o gazach wylotowych ogniwa paliwowego.
-
Study on Combined Optical and Electrochemical Analysis Using Indium-tin-oxide-coated Optical Fiber Sensor
PublikacjaThe growing needs for fast and reliable sensing devices stimulate development of new technological solutions. In this work a new multi-domain sensing method is demonstrated where optical sensing device has been applied to enhance amount of data received during electrochemical analysis. Thin, optically transparent, high-refractive-index, and electrically conductive indium tin oxide (ITO) film was deposited using magnetron sputtering...
-
In-situ Cu-doped MnCo-spinel coatings for solid oxide cell interconnects processed by electrophoretic deposition
PublikacjaThe Cu doping of the Mn–Co spinel is obtained “in-situ” by electrophoretic co-deposition of CuO and Mn1.5Co1.5O4 powders and subsequent two-step reactive sintering. Cu-doped Mn1.5Co1.5O4 coatings on Crofer22APU processed by electrophoretic co-deposition method are tested in terms of long term oxidation resistance and area specific resistance tests up to 3600 h. The introduction of Cu in the spinel lead to higher level of densification...
-
Effects of electrophoretic deposition times and nanotubular oxide surfaces on properties of the nanohydroxyapatite/nanocopper coating on the Ti13Zr13Nb alloy
PublikacjaLoad-bearing implants are developed with a particular emphasis placed on an application of ceramic hydroxyapatite coatings in order, to enhance the bioactivity of titanium implants and to shorten the healing time. Therefore, thin, fully crystalline coatings that are, highly adhesive, hydrophilic and demonstrating antibacterial properties are ly looked for. The aim of this research was to develop and characterize the properties...
-
The Potential Use of Citrus aurantifolia L. Essential Oils for Decay Control, Quality Preservation of Agricultural Products, and Anti-Insect Activity
Publikacja -
Nitrogen dioxide gas-sensing detection with GO modified CuO thin films
PublikacjaGas sensors have been continuously developed over the last few decades for several applications including air quality monitoring, automotive industry and recently for medical use. Gas sensors are usually based on metal oxides (MOXs), such as SnO2, TiO2, ZnO, WO3, CuO. Recently, new materials such as graphene oxide and heterostructures of graphene oxide and metal oxides are utilized for gassensing applications.
-
On the distribution of aluminium and magnesium oxides in wustite catalysts for ammonia synthesis
Publikacja -
Novel Class of Proton Conducting Materials—High Entropy Oxides
PublikacjaHere, for the first time, we present data on proton conductivity of high-entropy, single-phase perovskites. The BaZr0.2Sn0.2Ti0.2Hf0.2Ce0.2O3−δ, BaZr0.2Sn0.2Ti0.2Hf0.2Y0.2O3−δ, BaZr1/7Sn1/7Ti1/7Hf1/7Ce1/7Nb1/7Y1/7O3−δ, and BaZr0.15Sn0.15Ti0.15Hf0.15Ce0.15Nb0.15Y0.10O3−δ single-phase perovskites were synthesized. Before electrical measurements, materials were characterized using X-ray diffraction (XRD), scanning electron microscopy...
-
Benzophosphol-3-yl Triflates as Precursors of 1,3-Diarylbenzophosphole Oxides
PublikacjaAsimplemethodforthesynthesisof3-arylbenzophospholeoxidesunderSuzuki−Miyauracouplingconditionshasbeenpresented.Itemploysbenzophosphol-3-yltriflatestartingmaterialswhich,priortoourwork,hadnotbeenusedforthesynthesisof3-arylbenzophospholeoxides.Thereactionsproceedover24handprovidealibraryof3-arylbenzophospholeoxides.Thesyntheticaccesstothebenzophosphol-3-yltriflateshasbeenimproved.Thepreliminaryphotophysicalpropertiesofsome3-arylbenzophospholeoxideshavebeeninvestigatedbyabsorptionandemissionmeasurements.Thetheoreticalcalculationswereperformedtoestablishstructure−propertyrelationships.
-
Influence of hydrophobization of fumed oxides on interactions with polar and nonpolar adsorbates
Publikacja -
Positron Annihilation Studies of Silicon Oxides and Oxygen Precipitates in Silicon
PublikacjaTechniki pozytonowe dają możliwości badania defektów i zmian strukturalnych nie obserwowanych innymi metodami. W tej pracy zastosowano 3 różne techniki pozytonowe do badania zmian strukturalnych i tworzenia wydzieleń SiOx w krzemie.
-
Transition Metal Oxides influence on phosphate and borate glasses structure
PublikacjaBorate and phosphate glasses possess many potential luminescence and optical applications. With their low melting point, they are one of the most often studied amorphous materials. In recent years these glasses, doped with transition metal oxides (TMO), gained much attention due to their tunable structural and thermal properties. Review of systems containing TMOs was presented. Additionally synthesis of binary MnO-P2O5 and MnO-B2O3...
-
Visible light-induced photocatalytic reaction of gold-modified titanium(IV) oxide particles: action spectrum analysis
PublikacjaAnalizy spektrum działania wykazały, ze wzbudzenie powierzchniowego plazmonu złota inicjuje utlenianie 2-propanolu w świetle widzialnym w napowietrzonej zawiesinie tlenku(IV) tytanu zmodyfikowanego zlotem. Badania przeprowadzone z użyciem światła polichromatycznego wykazały, ze szybkość reakcji foto-utleniania zależy od właściwości tlenku(IV) tytanu, takich jak rozmiar ziaren, pola powierzchni właściwej, formy krystalicznej (anataz...
-
Co-free triple perovskite La1.5Ba1.5Cu3O7±δ as a promising air electrode material for solid oxide fuel cells
Publikacja -
Fe3O4/graphene oxide/Fe4[Fe(CN)6]3 nanocomposite for high performance electromagnetic interference shielding
Publikacja -
Investigation on structural, optical and anti-bacterial properties of organic additives iron oxide prepared by chemical route method
Publikacja -
Robust effectiveness behavior of synthesized cobalt doped Prussian blue graphene oxide ferrite against EMI shielding
Publikacja -
Reduced graphene oxide doping with nanometer-sized ferrocene moieties – New active material for glucose redox sensors
Publikacja -
Nanoconjugates of graphene oxide derivatives and meso-tetraphenylporphyrin: a new avenue for anticancer photodynamic therapies – Cell-on-a-Chip analysis
Publikacja -
Biochar-assisted transformation of engineered-cerium oxide nanoparticles: Effect on wheat growth, photosynthetic traits and cerium accumulation
Publikacja -
Improvement of Oxygen Electrode Performance of Intermediate Temperature Solid Oxide Cells by Spray Pyrolysis Deposited Active Layers
PublikacjaIntermediate temperature solid oxide fuel cells oxygen electrodes are modified by active interfacial layers. Spray pyrolysis is used to produce thin (≈500 nm) layers of mixed ionic and electronic conductors: Sm0.5Sr0.5CoO3−δ (SSC), La0.6Sr0.4CoO3−δ (LSC), La0.6Sr0.4Co0.2Fe0.8O3−δ (LSCF), and Pr6O11 (PrOx) on the electrode–electrolyte interface. The influence of the annealing temperature on the electrode polarization (area specific...
-
Removal of lead ions from wastewater using lanthanum sulfide nanoparticle decorated over magnetic graphene oxide
PublikacjaIn this study, the new lanthanum sulfide nanoparticle (La2S3) was synthesized and incorporated onto magnetic graphene oxide (MGO) sheets surface to produce potential adsorbent (MGO@LaS) for efficient removal of lead ions (Pb2+) from wastewater. The synthesized MGO@LaS adsorbent was characterized using Fourier transform infrared spectroscopy, field emission scanning electron microscopy and energy-dispersive X-ray spectroscopy. The...
-
Highly crystalline colloidal nickel oxide hole transport layer for low-temperature processable perovskite solar cell
PublikacjaHighly crystalline NiOX usually requires high annealing temperature (>300 °C) which is incompatible with flexible substrate and might consume high amount of energy. Herein, we demonstrate a facile emulsion process to synthesize highly crystalline, low temperature deposition (<150 °C) and solution processable NiOx nanoparticles (NPs) as a hole transport layer for the perovskite solar cells (PVSCs). A novel surfactant of tetramethylammonium...
-
Recent advances on spinel-based protective coatings for solid oxide cell metallic interconnects produced by electrophoretic deposition
PublikacjaThe application of ceramic protective coatings to the metallic interconnects in solid oxide cells (SOCs) is a viable and effective method to limit interconnect degradation issues. This featured letter provides a critical overview of the main outcomes of current research on the use of the electrophoretic deposition (EPD) technique to produce protective coatings for SOC metallic interconnects, specifically focusing on different approaches...
-
Chemically reduced graphene oxide based aerogels - Insight on the surface and textural functionalities dependent on handling the synthesis factors
PublikacjaEfficient adjusting of reduced graphene oxide aerogels properties requires information about experimental factor-aerogel property relationship. In this work, the reduced graphene oxide aerogels surface and textural functionalities in relation to precursor concentration, gelation time and hydrogel freezing temperature were studied in detail, with the use of dynamic adsorption method of gaseous organic probes and experimental design....
-
Mono- and bimetallic (Pt/Cu) titanium(IV) oxide photocatalysts. Physicochemical and photocatalytic data of magnetic nanocomposites’ shell
PublikacjaSurface modification of titania with noble and semi-noble metals resulted in significant enhancement of photocatalytic activity. Presented data, showing the photocatalytic properties of TiO2-M (where M is Pt and/or Cu) photocatalysts were further used as Fe3O4@SiO2/TiO2-M magnetic nanocomposites shells in "Mono- and bimetallic (Pt/Cu) titanium(IV) oxide core-shell photocatalysts with Vis light activity and magnetic separability"...
-
Highly crystalline colloidal nickel oxide hole transport layer for low-temperature processable perovskite solar cell
PublikacjaHighly crystalline NiOX usually requires high annealing temperature (>300 °C) which is incompatible with flexible substrate and might consume high amount of energy. Herein, we demonstrate a facile emulsion process to synthesize highly crystalline, low temperature deposition (<150 °C) and solution processable NiOx nanoparticles (NPs) as a hole transport layer for the perovskite solar cells (PVSCs)....
-
Zinc Oxide Nanoparticles Cytotoxicity and Release from Newly Formed PMMA–ZnO Nanocomposites Designed for Denture Bases
Publikacja -
Physical and sealing properties of BaO–Al2O3–SiO2–CaO–V2O5 glasses for solid oxide fuel cell applications
PublikacjaIn this study, the properties of BaO–Al2O3–SiO2 (SAB) glasses incorporated with CaO and V2O5 as the network modifier and additive, respectively, are evaluated. The electrical resistivities of the glasses decrease upon the addition of CaO but increase upon increasing their V2O5 content because the V5+ species lower the ionic mobility of the glasses. The addition of V2O5 improves the wettability of the glasses on the Crofer 22 APU...
-
Thickness and structure change of titanium(IV) oxide thin films synthesized by the sol–gel spin coating method
Publikacja -
Study of the chromatographic behavior of selected steroid hormones on aluminum oxide plates based on quantitative structure-retention relationships
Publikacja -
On the Possibility of Improving the Oxidation Resistance of High-Chromium Ferritic Stainless Steel Using Reactive Element Oxide Nanoparticles
PublikacjaHigh-chromium ferritic steels are current the only viable candidates for cheap interconnect materials for application in high-temperature solid oxide fuel and electrolyzer cells (HT-SOFCs/SOECs). The durability and operating characteristics of interconnects manufactured using these materials may be improved significantly by applying a protective-conducting MoCo2O4 coating and depositing an intermediate layer consisting of nanoparticles...
-
Experimental study and numerical simulation on porosity dependent direct reducibility of high-grade iron oxide pellets in hydrogen
PublikacjaThe transition to more environmentally friendly steel production methods has intensified research into hydrogen-based direct reduction (HyDR) of iron oxide pellets. The aim of this study is to systematically investigate the kinetics of the reduction process, the evolution of porosity and the resulting microstructural changes on the reduction behavior of high-quality pellets during HyDR of iron ore at different temperatures. A modified...
-
Evaluation of structural and electrical properties of multicomponent spinel oxide thin films deposited via spray pyrolysis technique
PublikacjaThis work reports the preparation of (Mn,Co,Fe,Ni,Cr)3O4 high-entropy spinel oxide in the form of a ~ 500 nm thin film utilising a facile spray pyrolysis technique. The structural and electrical properties of the layers were characterised after exposure to temperatures in the range of 400–900 ◦C. The as-deposited layers were amorphous, and crystallised upon heat treatment at 500 ◦C. Microstructural analyses proved a homogeneous...
-
Intense and stable room-temperature photoluminescence from nanoporous vanadium oxide formed by in-ambient degradation of VI3 crystals
PublikacjaVanadium oxides have attracted research interest because their optoelectronic properties make them optically active with room-temperature photoluminescence (PL) emission, which, however, is not sufficiently intense for real applications. For this reason, many nanostructured vanadium oxides are currently fabricated through several precursors and different treatments to improve the PL efficiency and enhance the PL intensity. Herein,...
-
Ultrafast self-expanded reduced graphene oxide and 2D MoS2 based films as anode in Li-ion battery
Publikacja -
Adsorption of anionic azo-dyes from aqueous solutions onto graphene oxide: Equilibrium, kinetic and thermodynamic studies
Publikacja -
Application of wet powder spraying for anode supported solid oxide fuel cell with a perowskite SrTi0.98Nb0.02O3-d anode
PublikacjaAnode-supported solid oxide fuel cell with SrTi0.98Nb0.02O3–d anode, yttria-stabilized zirconia electrolyte and La(Ni0.6Fe0.4) O3d cathode has been successfully fabricated and evaluated. Process of anode support fabrication has been presented. Wet powder spraying and high temperature sintering method have been studied and applied to deposit the thin electrolyte layer.In order to improve catalytic properties of the anode, it has...
-
Improved performance of LaNi0.6Fe0.4O3 solid oxide fuel cell cathode by application of a thin interface cathode functional layer
PublikacjaIn this work, novel functional layers were prepared by a low temperature spray pyrolysis method on the oxygen side of the solid oxide cells. Thin layers of Ce0.8Gd0.2O2 and LaNi0.6Fe0.4O3 are prepared between the electrolyte and the porous oxygen electrode. Additionally the influence of the sprayed ceria barrier layer on the zirconia based electrolyte with the new layers is evaluated. Impedance spectroscopy results show improvement...