Filtry
wszystkich: 3197
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: NONLINEAR OBSERVERS
-
Rotordynamic characteristics of a chamber seal
PublikacjaThe paper presents the results of numerical and experimental investigations into pressure forces generated in a turbine labyrinth seal of a modernized type. The experiments were performed on a single-stage air model turbine of the impulse type. The experiments were performed on a single-stage air model turbine of the impulse type. The experimental data were compared with theoretical results obtained by means of CFD Fluent Code....
-
Stability of trusses with linear elastic side-supports
PublikacjaThe present research is devoted to study of a lateral buckling of truss with linear elastic side supports. The elastic support reaction in relation to force in compressed chord and coefficient of buckling length related to side support distance are also calculated. The effect of slope of side support on limit force is also considered. The nonlinear analysis of two roof trusses are carried out. The results are compared to design...
-
Solving Boundary Value Problems for Second Order Singularly Perturbed Delay Differential Equations by ε-Approximate Fixed-Point Method
PublikacjaIn this paper, the boundary value problem for second order singularly perturbed delay differential equation is reduced to a fixed-point problem v = Av with a properly chosen (generally nonlinear) operator A. The unknown fixed-point v is approximated by cubic spline vh defined by its values vi = vh(ti) at grid points ti, i = 0, 1, ... ,N. The necessary for construction the cubic spline and missing the first derivatives at the boundary...
-
Predicting the seismic collapse capacity of adjacent SMRFs retrofitted with fluid viscous dampers in pounding condition
PublikacjaSevere damages of adjacent structures due to structural pounding during earthquakes have emphasized the need to use some seismic retrofit strategy to enhance the structural performance. The purpose of this paper is to study the influence of using linear and nonlinear Fluid Viscous Dampers (FVDs) on the seismic collapse capacities of adjacent structures prone to pounding and proposing modification factors to modify the median...
-
Comparison of classical Winter's bracing requirements of compressedtruss chord with stability analysis of 3D truss-model
PublikacjaMost code requirements concerning bracing are based on principles developed by Winter. The present research is devoted tostudy a lateral buckling of truss with linear elastic side supports. The classical Winter's model of truss chord in the case ofout of the truss plane buckling is compared with nonlinear analysis of 3D truss model. Full bracing condition, that permitsthe truss chord to support load level corresponding to an unbraced...
-
The Examination of the Upper Layers of the Seabed by the Means of the Acoustic Methods
PublikacjaPropagation of acoustic waves in the sea, in particular in shallow sea, depends on several factors. The basic of them are source power and frequency of acoustic waves, spatial distribution inhomogeneous medium in which acoustic wave propagates, and distributions of speed of sound and density of seawater. The coastal conditions, which limit water medium from above (free surface of the sea) and from bottom (the seabed), are no less...
-
Searching of the buried objects in the sea bottom by means of noninvasive methods
PublikacjaSearching of objects on the seabed or under its surface currently is a challenge for a number of researchers interested in the sea bottom. The problem relates to the objects on the depths of up to several tens of meters from the surface of the seabed. Finding the objects is the subject of interest for a wide group of users starting from archaeologists, and ending on groups interested in marine safety, as well as in military application...
-
Computational modelling of historic masonry railroad arch bridges
PublikacjaThe problems encountered during the analyzes of structural response of historic masonry railroad arch bridges are described in this paper. The attention is mainly focused on the stiffness of the masonry arches, their strengths and appropriate estimation of railroad load intensity. Issues related to computational modelling of two, existing, almost 130 years old masonry arch railroad bridges are presented in this context. The main...
-
The elasto-plastic numerical study of crack initiation in notched PMMA specimens under uniaxial loading conditions – Tension and torsion
PublikacjaThis paper presents the results of FEM numerical calculations aimed at describing the plastic strain and stress fields under critical loading conditions: tensile force or torsional moment. The calculations were carried out with reference to the results of experimental tensile and torsional tests of flat PMMA specimens weakened with V-notches of different root radii: 0.5, 2 and 10 mm. The procedure for conducting nonlinear numerical...
-
Optimal state feedback controller for balancing cube
PublikacjaIn this paper, a nonlinear balancing cube system is considered, the concept for which is based on an inverted pendulum. The main purpose of this work was the modelling and construction of a balancing cube with the synthesis of the control system. The control objectives included swing-up and stabilization of the cube on its vertex at an unstable equilibrium. Execution of the intended purpose required, first, deriving a cognitive...
-
Assessment of wastewater quality indicators for wastewater treatment influent using an advanced logistic regression model
PublikacjaInfluent quality indicators play a significant role in wastewater treatment plant performance due to their correlation with reactor operations and effluent quality. However, selecting a specific/best parameter indicator for predicting influent wastewater quality is one of the challenges in wastewa- ter treatment. This study, therefore, focused on determining suitable variables as influent quality indicators. For this purpose, a...
-
Synthesis of a state feedback controller for an averaging tank with variable filling
PublikacjaIn paper, a nonlinear averaging tank with variable filling is considered. The main purpose of this research work was the modelling and control system synthesis of an averaging tank. The control objectives included ensuring stability and zero steady-state error of the system and achieving settling time as short as possible, while maintaining a minimal overshoot. In order to achieve the intended purpose, firstly a mathematical model...
-
A simple and efficient hybrid discretization approach to alleviate membrane locking in isogeometric thin shells
PublikacjaThis work presents a new hybrid discretization approach to alleviate membrane locking in isogeometric finite element formulations for Kirchhoff–Love shells. The approach is simple, and requires no additional dofs and no static condensation. It does not increase the bandwidth of the tangent matrix and is effective for both linear and nonlinear problems. It combines isogeometric surface discretizations with classical Lagrange-based...
-
Determination of the theoretical and actual working volume of a hydraulic motor
PublikacjaA new methodology of determination of the theoretical and actual working volume of a hydraulic motor based on the characteristics of the delivered flow rate into hydraulic motor vs. the rotational speed at a constant pressure drop in the working chambers is described in this paper. A new method of describing the delivered flow rate into a motor per one shaft revolution as a nonlinear function of the pressure drop in the motor working...
-
Damage Analysis of Tensioning Cable Anchorage Zone of a Bridge Superstructure, Using CDP Abaqus Material Model
PublikacjaNumerical analysis of the tensioning cables anchorage zone of a bridge superstructure is presented in this paper. It aims to identify why severe concrete cracking occurs during the tensioning process in the vicinity of anchor heads. In order to simulate the tensioning, among others, a so-called local numerical model of a section of the bridge superstructure was created in the Abaqus Finite Element Method (FEM) environment. The...
-
Expedited Design Closure of Antennas By Means Of Trust-Region-Based Adaptive Response Scaling
PublikacjaIn the letter, a reliable procedure for expedited design optimization of antenna structures by means of trust-region adaptive response scaling (TR-ARS) is proposed. The presented approach exploits two-level electromagnetic (EM) simulation models. A predicted high-fidelity model response is obtained by applying nonlinear frequency and amplitude correction to the low-fidelity model. The surrogate created this way is iteratively rebuilt...
-
Improving SBR Performance Alongside with Cost Reduction through Optimizing Biological Processes and Dissolved Oxygen Concentration Trajectory
PublikacjaAuthors of this paper take under investigation the optimization of biological processes during the wastewater treatment in sequencing batch reactor (SBR) plant. A designed optimizing supervisory controller generates the dissolved oxygen (DO) trajectory for the lower level parts of the hierarchical control system. Proper adjustment of this element has an essential impact on the efficiency of the wastewater treatment process as well...
-
Computationally Effcient Solution of a 2D Diffusive Wave Equation Used for Flood Inundation Problems
PublikacjaThis paper presents a study dealing with increasing the computational efficiency in modeling floodplain inundation using a two-dimensional diffusive wave equation. To this end, the domain decomposition technique was used. The resulting one-dimensional diffusion equations were approximated in space with the modified finite element scheme, whereas time integration was carried out using the implicit two-level scheme. The proposed...
-
An enhanced method in predicting tensile behaviour of corroded thick steel plate specimens by using random field approach
PublikacjaThe present work investigates the possibility of using random field techniques in modelling the mechanical behaviour of corroded thick steel plate specimens. The nonlinear Finite Element method, employing the explicit dynamic solver, is used to analyse the mechanical properties of typical specimens. A material model considering full nonlinearity is used to evaluate the stress-strain response. The influence of major governing parameters...
-
On instabilities and post-buckling of piezomagnetic and flexomagnetic nanostructures
PublikacjaWe focus on the mechanical strength of piezomagnetic beam-like nanosize sensors during post-buckling. An effective flexomagnetic property is also taken into account. The modelled sensor is selected to be a Euler-Bernoulli type beam. Long-range interactions between atoms result in a mathematical model based on the nonlocal strain gradient elasticity approach (NSGT). Due to possible large deformations within a post-buckling phenomenon,...
-
Examination of fresh water chemistry in maritime Antarctica during austral summer 2017
PublikacjaDue to the fact that Antarctica is one of the least polluted places on Earth, it is a perfect place to observe the spread of global pollution. Therefore, research conducted on this continent is important due to the possibility of investigating the type of pollution and their way of transport. This work considers presence of organic contaminants in Maritime Antarctica in unexplored until now, Lions Rump headland. Qualitative and...
-
Optical flow method for measuring deformation of soil specimen subjected to torsional shearing
PublikacjaIn this study optical flow method was used for soil small deformation measurement in laboratory tests. The main objective was to observe how the deformation distributes along the whole height of cylindrical soil specimen subjected to torsional shearing (TS test). The experiments were conducted on dry non-cohesive soil specimens under two values of isotropic pressure. Specimens were loaded with low-amplitude cyclic torque to analyze...
-
The data exchange between smart glasses and healthcare information systems using the HL7 FHIR standard
PublikacjaIn this study we evaluated system architecture for the use of smart glasses as a viewer of information, as a source of medical data (vital sign measurements: temperature, pulse rate, and respiration rate), and as a filter of healthcare information. All activities were based on patient/device identification procedures using graphical markers or features based on visual appearance. The architecture and particular use cases were implemented...
-
Analysis of the Water Level Variation at the Polish Part of the Vistula Lagoon (2008-2017)
Dane BadawczeThe dataset consists of the following data:
-
The AFM micrographs of austenitic stainless steel subjected to sensitization for intergranular corrosion
Dane BadawczeThe dataset contains atomic force microscopy (AFM) maps of topographic images of austenitic steel samples subjected to sensitization to the process of intergranular corrosion. Precipitations of carbides as well as other intermetallic phases can be observed and detected before the fragments of structures sensitized by improper thermal treatment are exposed...
-
Sensorless Disturbance Detection for Five Phase Induction Motor with Third Harmonic Injection
PublikacjaThe paper presents a sensorless disturbance detection procedure that was done on a five phase induction motor with third harmonic injection. A test bench was developed where a three phase machine serves as disturbance generator of different frequencies. The control of the machines is based on multi scalar variables that ensures an independent control of the motor EMF and the rotor flux. For disturbance identification a speed observer...
-
Broadband dielectric spectroscopy studies of multiple times processed poly(lactic acid)-carbon black composites
Dane BadawczeThis dataset contains broadband dielectric spectroscopy studies of commercially available ProtoPasta 3D printable filament, composed of poly-lactic acid (PLA) and conductive carbon black (CB) filler. The aim of the study is to observe structural differences and applied properties changes under multiple reprocessing of the composite material at different...
-
Topography studies of multiple times processed poly(lactic acid)-carbon black composites
Dane BadawczeThis dataset contains topography studies with scanning electron microscope of commercially available ProtoPasta 3D printable filament, composed of poly-lactic acid (PLA) and conductive carbon black (CB) filler. The aim of the study is to observe structural differences and applied properties changes under multiple reprocessing of the composite material...
-
Electrochemical analyses of multiple times processed poly(lactic acid)-carbon black composites
Dane BadawczeThis dataset contains cyclic voltammetry studies of commercially available ProtoPasta 3D printable filament, composed of poly-lactic acid (PLA) and conductive carbon black (CB) filler. The aim of the study is to observe structural differences and applied properties changes under multiple reprocessing of the composite material at different temperatures...
-
Thermal analyses of multiple times processed poly(lactic acid)-carbon black composites
Dane BadawczeThis dataset contains thermal analyses (TGA, DTG, DSC) studies of commercially available ProtoPasta 3D printable filament, composed of poly-lactic acid (PLA) and conductive carbon black (CB) filler. The aim of the study is to observe structural differences and applied properties changes under multiple reprocessing of the composite material at different...
-
Active and Dynamic Graphical Code for Object Identification in Healthcare
PublikacjaA new approach for item marking using two dimensional discrete graphics markers. Proposed solution allow o change the code rapidly, upon request and in the case of thermal markers make the code invisible for unauthorized observers. Connecting the proposed codes with wearable multmedial platform such as eGlasses can create new possibilities in human-environment interaction.
-
Determination of mechanical properties of Ti13Nb13Zr cubes made with STL technology subjected to uniaxial compression
Dane BadawczeThe aim of the study was to determine the mechanical properties of Ti13Nb13Zr cubes made with STL technology (3D printing). The experiments were carried out on the Hung Ta universal test machine HT-2402. Cubes with the initial dimensions of 10x10x10 mm were subjected to compression by increasing force to over 80 kN. In various experiments, the angle...
-
TDOA versus ATDOA for wide area multilateration system
PublikacjaThis paper outlines a new method of a location service (LCS) in the asynchronous wireless networks (AWNs) where the nodes (base stations) operate asynchronously in relation to one another. This method, called asynchronous time difference of arrival (ATDOA), enables the calculation of the position of the mobile object (MO) through the measurements taken by a set of non-synchronized fixed nodes and is based on the measurement of...
-
Methylation effect in e−— scattering on methyl-substituted ethylenes
PublikacjaMethylation effect has been observed and studied in electron-scattering from selected hydrocarbon molecules. In measured total cross section (TCS) functions we have noticed energy shifts and changes in the intensity of observed structures.
-
Finite element models used in diagnostics of transverse cracks in bridge approach pavement
Dane BadawczeTransverse cracks in the asphalt pavement were observed on bridge structures next to single-module expansion joints with a 5 meter approach slab set at the depth of 1 m. The finite element (FE) models of the approach pavement were created to investigate the reasons of premature cracking and crack initiation mechanism over the back edge of the abutment...
-
Cyclic behavior of FeCoCrNiMn high entropy alloy coatings produced through cold spray
PublikacjaeCoCrNiMn high entropy alloy powders were employed to produce coatings on carbon steel through high pressure cold spray (at 1100 °C and 7 MPa in temperature and pressure respectively). X-ray diffraction of the sprayed material revealed a dense coating with the retention of the original crystallographic structure. Once splatted, particles revealed high flattening ratio with consequent excellent adhesion of the coating to the substrate....
-
Rheology studies of multiple times processed poly(lactic acid)-carbon black composites
Dane BadawczeThis dataset contains MFR/MVR (melt flow rate) rheology studies of commercially available ProtoPasta 3D printable filament, composed of poly-lactic acid (PLA) and conductive carbon black (CB) filler. The study aims to observe structural differences and applied properties changes under multiple reprocessing of the composite material at different temperatures...
-
Surrogate Modeling and Optimization Using Shape-Preserving Response Prediction: A Review
PublikacjaComputer simulation models are ubiquitous in modern engineering design. In many cases, they are the only way to evaluate a given design with sufficient fidelity. Unfortunately, an added computa-tional expense is associated with higher fidelity models. Moreover, the systems being considered are often highly nonlinear and may feature a large number of designable parameters. Therefore, it may be impractical to solve the design problem...
-
Examples of numerical simulations of two-dimensional unsaturated flow with VS2DI code using different interblock conductivity averaging schemes
PublikacjaFlow in unsaturated porous media is commonly described by the Richards equation. This equation is strongly nonlinear due to interrelationships between water pressure head (negative in unsaturated conditions), water content and hydraulic conductivity. The accuracy of numerical solution of the Richards equation often depends on the method used to estimate average hydraulic conductivity between neighboring nodes or cells of the numerical...
-
Acoustic streaming caused by some types of aperiodic sound. Buildup of acoustic streaming
PublikacjaThe analysis of streaming caused by aperiodic sound of different types (switched on at transducer sound or sound determined by initial conditions) is undertaken. The analysis bases on analytical governing equation for streaming Eulerian velocity, which is a result of decomposition of the hydrodynamic equations into acoustic and non-acoustic parts. Its driving force (of acoustic nature) represents a sum of two terms; one is the...
-
Evolutionary Algorithms in MPLS network designing
PublikacjaMPLS technology become more and more popular especially in core networks giving great flexibility and compatibility with existing Internet protocols. There is a need to optimal design such networks and optimal bandwidth allocation. Linear Programming is not time efficient and does not solve nonlinear problems. Heuristic algorithms are believed to deal with these disadvantages and the most promising of them are Evolutionary Algorithms....
-
Seismic pounding behavior of multi-story buildings in series considering the effect of infill panels
PublikacjaThe aim of the present paper is to study the influence of the infill panels on the seismic pounding response of adjacent structures in series. The contribution of the masonry infill has been simulated using equivalent diagonal compression struts. Steel frames have been assumed to have elastic-plastic behavior with 1% linear strain hardening. The dynamic contact analysis has been utilized where contact surface model (target and...
-
Textile reinforced concrete members subjected to tension, bending, and in-plane loads: Experimental study and numerical analyses
PublikacjaTextile reinforced concrete has raised increasing research interest during the last years, mainly due to its potential to be used for freeform shell structures involving complex load situations. Yet, most experimental work has focused on test setups with primarily uniaxial loading. In the current work, such setups are complemented with a novel test setup of deep beams, including in-plane bending and shear. Further, nonlinear finite...
-
Fractional Spectral and Fractional Finite Element Methods: A Comprehensive Review and Future Prospects
PublikacjaIn this article, we will discuss the applications of the Spectral element method (SEM) and Finite element Method (FEM) for fractional calculusThe so-called fractional Spectral element method (f-SEM) and fractional Finite element method (f-FEM) are crucial in various branches of science and play a significant role. In this review, we discuss the advantages and adaptability of FEM and SEM, which provide the simulations of fractional...
-
Detection of Closing Crack in Beam Based on Responses Induced by Harmonic Excitation
PublikacjaThe non-linear contact model was chosen to simulate the closed crack in the cantilever beam. The study examines the shape and characteristics of the phase diagram of a cantilever beam with closed cracks. It investigates how various crack properties influence the geometry of the phase diagram and proposes a method for identifying cracks based on their features. The area of each closed curve in the phase diagram is determined using...
-
An isogeometric finite element formulation for frictionless contact of Cosserat rods with unconstrained directors
PublikacjaThis paper presents an isogeometric finite element formulation for nonlinear beams with impenetrability constraints, based on the kinematics of Cosserat rods with unconstrained directors. The beam cross-sectional deformation is represented by director vectors of an arbitrary order. For the frictionless lateral beam-to-beam contact, a surface-to-surface contact algorithm combined with an active set strategy and a penalty method...
-
Testing of the longest span soil-steel bridge in Europe – new quality in measurements
PublikacjaThe article describes interdisciplinary and comprehensive diagnostic tests of final bridge inspection and acceptance proposed for a soil – steel bridge made of corrugated sheets, being the European span length record holder (25.74 m). As an effect of an original concept a detailed and precise information about the structure response was collected. The load test design was based on the nonlinear numerical simulations performed by...
-
A new approach to designing control of dissolved oxygen and aeration system in sequencing batch reactor by applied backstepping control algorithm
PublikacjaThe Wastewater Treatment Plant (WWTP) is a very complex system, due to its nonlinearity, time-variance, and multiple time scales in its dynamics among others. The most important control parameter in a WWTP is the Dissolved Oxygen (DO) concentration. The tracking problem of the DO concentration is one of the most fundamental issues in biological wastewater treatment. Proper DO concentration control is necessary to achieve adequate...
-
Electro-mechanical shear buckling of piezoelectric nanoplate using modified couple stress theory based on simplified first order shear deformation theory
PublikacjaThis paper studies the electro-mechanical shear buckling analysis of piezoelectric nanoplate using modified couple stress theory with various boundary conditions.In order to be taken electric effects into account, an external electric voltage is applied on the piezoelectric nanoplate. The simplified first order shear deformation theory (S-FSDT) has been employed and the governing differential equations have been obtained using...
-
CONTROL OF THE WAVES IN A TOWING TANK WITH THE USE OF A BLACK-BOX MODEL
PublikacjaThe paper describes an adaptive control system of the waves, implemented in the Ship Design and Research Centre, CTO S.A. The purpose of generating the waves in the towing tank is the modelling of the environmental conditions during hydrodynamic model tests. The tests are performed on scale models of towed or free running ships, anchored structures like oil rigs or bottommounted structures, e.g. wind turbines. In the towing tank...