wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: TRANSPARENT COATINGS
-
Compliance tests of the polymer layers used as hydrodynamic bearing coatings
PublikacjaOperational experience and scientific investigations results showed that polymer lined hydrodynamic bearings can withstand more severe operating conditions compared than white metal bearings. PTFE and PEEK-based coatings are the most frequently used as Babbitt alternatives. Both polymers differ significantly from the each other in material properties. According to catalogue data compression modulus of PTFE, it is about an order...
-
Local properties of organic coatings close to glass transition temperature
PublikacjaAcrylic coating applied on copper substrate has been investigated at different temperatures starting from the ambient one up to the level above the glass transition temperature. Its local topographic and electric properties have been examined with the atomic force microscopy (AFM) based approach including dc current mapping and local impedance spectroscopy. The local findings have been compared with the information from global...
-
The protective properties of graphene oxide coatings functionalized with phosphorus atoms.
PublikacjaRecently, electrophoretically deposited graphene oxide coatings are commonly applied as an anti-corrosion layer. However, improper adjustment of electrophoretic deposition (EPD) parameters as well as the hydrophilic nature of graphene oxide contribute to the formation of defects in the coatings and the increase in the wetting properties, respectively, and thus lead to a reduction of protective properties. The growth of wetting...
-
Fatigue Bending of V-Notched Cold-Sprayed FeCoCrNiMn Coatings
PublikacjaCold-spray coatings were produced by FeCoCrNiMn high-entropy alloy powders deposited on carbon steel substrate. The coatings were realized at intermediate temperature and high pressure (at 1100 °C and 7 MPa). The coating microstructure was characterized by scanning electron microscopy and X-ray diffraction, revealing a very dense deposition and high flattening ratio of the splatted particles. This had a large influence on the...
-
Application of percolation theory for description of electrical properties of conducting coatings
PublikacjaPrzedstawiono pomiary elektryczne i elektrochemiczne powłok organicznych przewodzących prąd elektryczny i mogących pełnić rolę anody w systemie ochrony katodowej żelbetonu. Za pomocą pomiarów impedancyjnych dokonano oceny rezystancji powłoki w funkcji zawartości grafitu. Na tej podstawie oszacowano próg perkolacji powłoki epoksydowej domieszkowanej elektrografitem. Ocenę obciążalności prądowej powłok przewodzących dokonano wykonując...
-
Evaluating and predicting the performance of organic coatings using impedance spectroscopy
PublikacjaPrzedstawiono wyniki badań cyklicznych, sinusoidalnych zmian temperatury na powłokowe systemy ochronne o skrajnie różnych właściwościach antykorozyjnych. Porównano zachowanie nowej powłoki poliestrowej typu "coil-coating" na ocynkowanej stali uprzednio eksponowanej w warunkach atmosferycznych alkidowej powłoki malarskiej na podłożu stalowym. Badania przeprowadzono przy zastosowaniu techniki spektroskopii impedancyjnej. Stwierdzono...
-
Effect of environmental temperature variations on protective properties of organic coatings
PublikacjaW oparciu o model rozwoju naprężeń oraz niszczenia kumulatywnego przedyskutowano wpływ zmiennych temperatur środowiska na mechaniczną spójność i własności ochronne systemów powłokowych. Badano wpływ cykli temperaturowych pomiędzy 20 i 55 st. C oraz między -20 i 20 st. C na trwałość różnych powłokowych systemów malarskich na stali. Stosując technikę spektroskopii impedancyjnej monitorowano zmiany parametrów powłok poddanych cyklom...
-
Degradation of organic coatings subjected to alternating mechanical stress impact.
PublikacjaW pracy przedstawiono wyniki badań nad wpływem cyklicznych naprężeń mechanicznych na dwa rodzaje systemów powłokowych stosowanych do ochrony konstrukcji mostowych. Powłoki epoksydowe i winylowe poddano cyklom zginanie/odpuszczenie w granicach odkształceń elastycznych materiału podłoża. Stan powłok oceniano przy użyciu techniki elektrochemicznej spektroskopii impedancyjnej. Otrzymane wyniki porównano z zachowaniem analogicznych...
-
Accelerated degradation of organic coatings due to cyclic mechanical stress
PublikacjaPotrzeba okresowej renowacji wymalowań na obiektach technicznych wynika z naturalnej degradacji powłok ochronnych wskutek oddziaływania czynników obecnych w miejscu eksploatacji. W niniejszej pracy opisano synergiczny wpływ dwóch z nich - promieniowana ultrafioletowego i cyklicznych naprężeń mechanicznych - na trwałość komercyjnie stosowanego zestawu powłokowego przeznaczonego do ochrony konstrukcji mostowych.
-
Cyclic mechanical stress impact on protective properties of organic coatings
PublikacjaCelem pracy jest zaprezentowanie wyników badań wpływu cyklicznych naprężeń mechanicznych na układy powłoka/metal. Powtarzające się naprężenia mechaniczne zostały zidentyfikowane jako czynnik w znaczącym stopniu przyczyniający się do degradacji powłok. Próbki składające się z powłoki epoksydowej nałożonej na stal St3SAl poddano serii 21000 cykli naprężenie-odpuszczenie. Badania przeprowadzono w zakresie odkształceń elastycznych...
-
Application of the dynamic EIS to investigation of transport within organic coatings
PublikacjaW pracy przedstawiono wyniki badań nad gwałtownym niszczeniem organicznych powłok ochronnych. Zastosowano technikę Dynamicznej Elektrochemicznej Spektroskopii Impedancyjnej (DEIS). Przez 60 sekund powłoka poliwinylowa poddawana była działaniu chlorku metylenu. W tym czasie rejestrowano chwilowe widma impedancyjne, co pozwoliło na prześledzenie dynamiki procesu degradacji powłoki. Potwierdzono przydatność techniki DEIS w badaniu...
-
Fatigue damage evaluation of organic coatings subjected to mechanical stress
PublikacjaZnaczna liczba konstrukcji ulega niszczeniu zmęczeniowemu w wyniku oddziaływania cyklicznych naprężeń mechanicznych. Jednakże w dziedzinie organicznych powłok ochronnych czynnik ten pozostaje niedoceniany. W pracy dokonano porównania wpływu cyklicznych naprężeń mechanicznych na nowe i pre-eksponowane (w podwyższonej temperaturze lub promieniowaniu UV) powłoki epoksydowe.
-
Polyurethanes for Coating, Adhesives, and Other Applications
PublikacjaAn interesting group of polyurethane (PU) materials are coatings, adhesives, sealants, and thickeners. A wide base of raw materials and various methods of PU synthesis allows production of materials with a wide range of properties that can be commonly used in many industries. This chapter describes the main types of PU coatings and adhesives and special application PUs and the methods of their production. The materials described...
-
Nanotubular oxide layers and hydroxyapatite coatings on porous titanium alloy Ti13Nb13Zr
PublikacjaThe surface condition of an implant has a significant impact on response occurring at the implant-biosystem border. The knowledge of physical-chemical and biological processes allows for targeted modification of biomaterials to induce a specified response of a tissue. The present research was aimed at development of technology composing of obtaining the nanotube oxide layers on a porous titanium alloy Ti13Nb13Zr, followed by the...
-
pH-dependent composite coatings for controlled drug delivery system - Review
PublikacjaNowadays in case of long-term implants, the most common postoperative complications are bacterial infections, which in consequence may provoke loos- ening of the implants in the primary phase of stabilization. Bacterial infections are currently the most frequent cause of revision surgery of the implants such as hip joint endoprosthesis, knee joint endoprosthesis and dental implants. In order to provide the local and long-term antibacterial...
-
Polymer biodegradable coatings as active substance release systems for urological applications
PublikacjaCatheter-associated urinary tract infections are the result of catheterization of the bladder. The risk of infection is directly proportional to the length of the bladder catheterization. Bacteria cells have the ability to adhere and create the biofilm on the surface of catheter materials. Bacteria’s biofilm is an extremely beneficial environment of existence for microorganisms. Microorganisms that are an integral part of the biofilm...
-
Comparison of Properties of the Hybrid and Bilayer MWCNTs—Hydroxyapatite Coatings on Ti Alloy
PublikacjaCarbon nanotubes are proposed for reinforcement of the hydroxyapatite coatings to improve their adhesion, resistance to mechanical loads, biocompatibility, bioactivity, corrosion resistance, and antibacterial protection. So far, research has shown that all these properties are highly susceptible to the composition and microstructure of coatings. The present research is aimed at studies of multi-wall carbon nanotubes in three different...
-
Nickel-nanodiamond coatings electrodeposited from tartrate electrolyte at ambient temperature
PublikacjaIn this study, nanocrystalline Ni and Ni-diamond coatings were obtained by electrodeposition from tartrate electrolyte at ambient temperature aiming at improving corrosion and wear properties of the material. The created surfaces were investigated with regard to microhardness, adhesion, wear- and corrosion-resistance. The various methods such as atomic force microscopy, scanning electron microscopy, electrochemical impedance spectroscopy...
-
Nanocrystalline diamond sheets as protective coatings for fiber-optic measurement head
PublikacjaFiber-optic sensors find numerous applications in science and industry, but their full potential is limited because of the risk of damaging the measurement head, in particular, due to the vulnerability of unprotected tips of the fiber to mechanical damage and aggressive chemical agents. In this paper, we report the first use of a new nanocrystalline diamond structure in a fiber-optic measurement head as a protective coating of...
-
Effects of the Origin and Deacetylation Degree of Chitosan on Properties of Its Coatings on Titanium
PublikacjaThe properties of chitosan coatings on titanium surfaces may be influenced by a variety of factors, including their chemical characteristics and the deposition method. The aim of this research was to determine the influence of a chitosan’s origin (a type of shrimp) and deacetylation degree (DD), when deposited on a very smooth titanium surface, on adhesion and biological behavior. The tests were performed using chitosan of a degree...
-
The Effects of Silver Ion Implantation on Structural and Morphological Performance of Hydroxyapatite Coatings
Publikacja -
Ammonium Hydroxide Mediated Hydrothermal Crystallization of Hydroxyapatite Coatings on Titanium Substrate
Publikacja -
Nanoparticle coatings for stir bar sorptive extraction, synthesis, characterization and application
Publikacja -
Characteristics of Hybrid Bioglass-Chitosan Coatings on the Plasma Activated PEEK Polymer
Publikacja -
Tribological performance of PTFE-metal binary coatings in rolling/sliding contact
PublikacjaTribological performance of surface coatings with embedded PTFE reservoirs in rolling/sliding contact is reported. Using two different coating materials and two shapes and patterns of PTFE reservoirs test samples in the form of discs were prepared and tested in a four-ball contact configuration under loads corresponding to nominal contact pressure of 0.5 and 1.0 GPa. It was found that one coating, namely aluminium-bronze with embedded...
-
Nanotubular oxide layers and hydroxyapatite coatings on ‘Ti–13Zr–13Nb’ alloy
PublikacjaThe presented research was aimed to determine the mechanical properties of the nanotubular oxide layer covered with hydroxyapatite coating. The Ti–13Zr–13Nb alloy was oxidised in 1M phosphoric acid with an addition of 0?5% HF for HF solution at 20 V voltage. The electrochemically assisted deposition of hydroxyapatite was performed at cyclic polarisation in NH4H2PO4 and CaCl2 solution at 80uC. The mechanical properties were determined...
-
Degradation of protective coatings in steel chimneys of flue gas desulfurisation system
PublikacjaThis paper presents problems associated with corrosion of steel stacks and changes in philosophy of corrosion protection when implemented into flue gas desulphurization systems. In-situ tests were taken by means of electrochemical impedance spectroscopy at the stack which discharges flue gas before wet lime/limestone desulphurization. A very quick electrolyte absorption by the spherical infill vinylester coating was found using...
-
Ceria Based Protective Coatings for Steel Interconnects Prepared by Spray Pyrolysis
PublikacjaStainless steels can be used in solid oxide fuel/electrolysis stacks as interconnects. For successful long term operation they require protective coatings, that lower the corrosion rate and block chemical reactions between the interconnect and adjacent layers of the oxygen or the hydrogen electrode. One of the promising coating materials for the hydrogen side is ceria. Using standard sintering techniques, ceria sinters at around...
-
Thermal boundary conditions to simulate friction layers and coatings at sliding contacts
PublikacjaA brief review of the thermal boundary conditions specified at sliding interfaces was performed. New thermal boundary conditions were derived aimed at solving problems of sliding with account of surface layers representing friction layers and tribological coatings. Based on the assumption of linear temperature distributions in the surface layers, the proposed conditions enable one to simplify simulations by eliminating the surface...
-
Chitosan/poly(4-vinylpyridine) coatings formed on AgNPs-decorated titanium
PublikacjaElectrophoretic deposition (EPD) of chitosan/poly(4-vinylpyridine) (chit/P4VP) coatings on titanium substrates previously decorated with silver nanoparticles (AgNPs) was performed at different content of P4VP in the suspension and different voltage values. The results revealed that the composite coatings were formed, well-adjacent to the titanium substrate, of suitable roughness, hydrophilicity, and corrosion resistance. The voltage...
-
Stratification of nano-pigments in anti-corrosive coatings by means of magnetic field
PublikacjaThe concept of self-stratification of coatings, although attractive, causes difficulties in its practical use, especially when pigments are added to the resins. An alternative way of obtaining a multilayer structure in a single step was presented. Using the inhomogeneous magnetic field and magnetically active components of the coating, the possibility of vertically graded differentiation of the one layer properties has been verified....
-
Thermal-Resistant Polyurethane/Nanoclay Powder Coatings: Degradation Kinetics Study
PublikacjaIn the present study, thermal degradation kinetics of polyurethane (PU) powder coatings reinforced with organo-modified montmorillonite (OMMT) was investigated. PU nanocomposites were prepared in different concentrations of 1, 3, and 5 wt.% of OMMT via the extrusion method. The microstructure of the nanocomposites was observed by scanning electron microscope (SEM) illustrating uniform dispersion of OMMT nano-clay platelets in the...
-
Preparation and properties of composite coatings, based on carbon nanotubes, for medical applications
PublikacjaThe coatings based on carbon nanotubes (CNTs) are increasingly developed for their applications, among others, in medicine, in particular for implants in implantology, cardiology, and neurology. The present review paper aims at a detailed demonstration of diferent preparation methods for such coatings, their performance, and relationships between deposition parameters and microstructure and material, mechanical, physical, chemical,...
-
Antimicrobial and Antiproliferative Coatings for Stents in Veterinary Medicine—State of the Art and Perspectives
PublikacjaMicrobial colonization in veterinary stents poses a significant and concerning issue in veterinary medicine. Over time, these pathogens, particularly bacteria, can colonize the stent surfaces, leading to various complications. Two weeks following the stent insertion procedure, the colonization becomes observable, with the aggressiveness of bacterial growth directly correlating with the duration of stent placement. Such microbial...
-
Preparation and Characterization of Diamond-like Carbon Coatings for Biomedical Applications—A Review
PublikacjaDiamond-like carbon (DLC) films are generally used in biomedical applications, mainly because of their tribological and chemical properties that prevent the release of substrate ions, extend the life cycle of the material, and promote cell growth. The unique properties of the coating depend on the ratio of the sp3/sp2 phases, where the sp2 phase provides coatings with a low coefficient of friction and good electrical conductivity,...
-
New method using bilinear transformation for parameter identification ofanticorossion coatings.
PublikacjaArtykuł przedstawia nową metodę diagnostyki powłok antykorozyjnych z wykorzystaniem przekształcenia biliniowego. Możliwa jest identyfikacja parametrów schematu zastępczego powłoki na podstawie pomiaru impedancji obiektu na kilku, optymalnie dobranych częstotliwościach pomiarowych. Podano zasady doboru optymalnych częstotliwości pomiarowych. Ich liczba jest równa liczbie elementów schematu zastępczego. Opracowany algorytm identyfikacji...
-
Cavitation erosion of heterogeneous thin coatings produced by means of laser cladding
PublikacjaPrzedstawiono badania odporności kawitacyjnej cienkich heterogenicznych warstw nakładanych metodami laserowymi na stal 45. Wykazano dobrą przyczepność i wysoką odporność kawitacyjną wykonanych powłok.
-
Assessment of fatigue damage of organic coatings subjected to cyclic mechanical stress
PublikacjaTechnika szumu elektrochemicznego od ponad 20 lat stanowi przedmiot intensywnych badań mających na celu jej praktyczne zastosowanie w monitorowaniu korozji. U podstaw omawianej metody leży odpowiednia analiza rejestrowanych symultanicznie przebiegów prądowych i potencjałowych. W zależności od użytej techniki obróbki danych uzyskane mogą być informacje dotyczące ilościowych (szybkość) i jakościowych (rodzaj zaatakowania) cech procesu...
-
Transverse surface waves on a cylindrical surface with coating
PublikacjaWe discuss the propagation of transverse surface waves that are so-called whispering-gallery waves along a surface of an elastic cylinder with coating. The coating is modelled in the framework of linearized Gurtin–Murdoch surface elasticity. Other interpretations of the surface shear modulus are given and relations to so-called stiff interface and stiff skin model are discussed. The dispersion relations are obtained and analyzed.
-
The lubricant-coating interaction in rolling and sliding contacts
Publikacja -
Hydroxyapatite films as biocompatibile coating for artifical bone
PublikacjaW artykule została szczegółowo opisana budowa kości oraz materiał biokompatybilny hydroksyapatyt (HAp). Autorzy wykazali jak wielkie podobieństwo do budowy kości przejawia sztuczny hydroksyapatyt. opisali syntezy powłoki z HAp.
-
Examination of the epoxy coating system's resistance to Corrobill
PublikacjaThe tests of the influence of the surface cleaning agent on the epoxy coating were carried out. Electrochemical and corrosion tests were carried out. The effect of the preparation on the adhesion and hardness of the tested coating was tested.
-
Impedance measurements of coating properties on bridge structures
PublikacjaPomiary impedancyjne pozwalają na prostą ocenę właściwości ochronnych powłok ochronnych i wykładzin. Pomiary stosuje się w celu porównania powłok, monitorowania ich właściwości i oceny mechanizmu działania. Metodyka jest z powodzeniem stosowana w pomiarach laboratoryjnych. Pomiary terenowe są bardziej skomplikowane ponieważ wymagają w pełni kontrolowanych komputerowo przyrządów, kontroli warunków pogodowych oraz wielu innych parametrów...
-
Evaluation of coating systems using impedance spectroscopy
PublikacjaTrwałość powłokowych systemów ochronnych zależy od oddziaływań środowiska i związana jest nieodwracalnymi procesami chemicznymi i fizycznymi. Zastosowanie spektroskopii impedancyjnej pozwala na określenie obszaru zastosowań danej powłoki i prognozowanie okresu jej trwałości. W pracy zamieszczono przykłady oceny trwałości systemów powłokowych stosowanych w strategicznych konstrukcjach.
-
Giant increase of optical transparency for Zn-rich CaxZn1−xO on Al2O3 (0001) grown by pulsed laser deposition
Publikacja -
Financial system ratings.
PublikacjaW rozdziale tym autor przedstawił wyniki swoich badań nad wykorzystaniem sztucznych sieci neuronowych w prognozowaniu upadłości przedsiębiorstw. Przedstawiono również propozycję klasyfikacji metod analizy dyskryminacyjnej oraz perceptronu wielowarstwowego stosowanych w prognozowaniu zagrożeń upadłością firm. Tabel:2, rysunków:9.
-
Towards high quality ITO coatings: the impact of nitrogen admixture in HiPIMS discharges
PublikacjaThe paper reports controlled deposition of optically transparent and electrically conductive ITO films prepared by a combination of rf (13.56 MHz) and High Power Impulse Magnetron Sputtering (HiPIMS) systems without any post deposition thermal treatment/annealing. It is shown that (i) reactive admixture of N2 gas to the process and (ii) pressure in the deposition chamber enable to optimize optical properties of ITO films. Furthermore,...
-
Properties of Nanohydroxyapatite Coatings Doped with Nanocopper, Obtained by Electrophoretic Deposition on Ti13Zr13Nb Alloy
PublikacjaNowadays, hydroxyapatite coatings are the most common surface modification of long-term implants. These coatings are characterized by high thickness and poor adhesion to the metallic substrate. The present research is aimed at characterizing the properties of nanohydroxyapatite (nanoHAp) with the addition of copper nanoparticle (nanoCu) coatings deposited on the Ti13Zr13Nb alloy by an electrophoresis process. The deposition of...
-
Microstructure and mechanical properties of laser surface-treated Ti13nb13zr alloy with MWCNTs coatings
PublikacjaLaser surface modification of titanium alloys is one of the main methods of improving the properties of titanium alloys used in implantology. This study investigates the microstructural morphology of a laser-modified surface layer on a Ti13Nb13Zr alloy with and without a carbon nanotube coating deposited by electrophoretic deposition. Laser modification was performed for samples with and without carbon nanotube coating for two...
-
Polyurethane/Silane-Functionalized ZrO2 Nanocomposite Powder Coatings: Thermal Degradation Kinetics
PublikacjaA polyurethane (PU)-based powder coating reinforced with vinyltrimethoxysilane (VTMS)-functionalized ZrO2 nanoparticles (V-ZrO2) for thermal stability was developed. Chemical structure, microstructure and thermal degradation kinetics of the prepared coatings were investigated. The peak of aliphatic C–H vibrating bond in the Fourier transform infrared (FTIR) spectrum of V-ZrO2 was a signature of VTMS attachment. Scanning electron...