Filtry
wszystkich: 1465
-
Katalog
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: tagging
-
Glass-ceramic joining of Fe22Cr porous alloy to Crofer22APU: interfacial issues and mechanical properties
PublikacjaThis work deals with the joining of porous Fe22Cr ferritic stainless steel to a dense Crofer22APU plate by using a silica-based, Ba-containing glass-ceramic. The chemical and interfacial stability and the mechanical properties of the joints were evaluated before and after thermal ageing at 700 ◦C for 500hrs. The sintering behaviour of the glass was assessed by using heating stage microscopy (HSM) to study the influence of a porous...
-
Experimental study and comparison with predictive methods for flow boiling heat transfer coefficient of HFE7000
PublikacjaThis article describes an experimental study of flow boiling of HFE7000 inside a smooth vertical channel. The investigation has been carried out in a circular stainless-steel tube with an inner diameter of 2.3 mm. The data have been collected for the applied heat fluxes q ranging from 61 to 205 kW/m2, the mass flux G ranging from 214 to 1006 kg/(m2 s), the saturation temperature Tsat ranging from 30 to 54 °C and the full range...
-
Improved methods for stator end winding leakage inductance calculation
PublikacjaCalculating the stator end-winding leakage inductance, taking into account the rotor, is difficult due to the irregular shape of the end-winding. The end-winding leakage may distribute at the end of the active part and the fringing flux of the air gap. The fringing flux belongs to the main flux but goes into the end-winding region. Then, not all the magnetic flux occurring in the end region is the end-winding leakage flux. The...
-
Electron-impact ionization cross section calculations for selected ribonucleosides
PublikacjaTotal cross sections for the single electron-impact ionization of selected ribonuclosides (guanosine, adenosine, cytidine and uridine) have been calculated for electron energies ranging from the ionization threshold up to 5 keV.
-
Transformational Leadership and Acceptance of Mistakes as a Source of Learning: Poland-USA Cross-Country Study
PublikacjaThis study explores the influence of transformational leadership on internal innovativeness mediated by mistakes acceptance, including country and industry as factors to be considered and gender and risk-taking attitude as moderators. General findings, primarily based on the US samples (healthcare, construction, and IT industry), confirmed that transformational leadership and internal innovativeness are mediated by mistakes acceptance...
-
Development of an AI-based audiogram classification method for patient referral
PublikacjaHearing loss is one of the most significant sensory disabilities. It can have various negative effects on a person's quality of life, ranging from impeded school and academic performance to total social isolation in severe cases. It is therefore vital that early symptoms of hearing loss are diagnosed quickly and accurately. Audiology tests are commonly performed with the use of tonal audiometry, which measures a patient's hearing...
-
Applications for investigating therapy progress of autistic children
PublikacjaThe paper regards supporting behavioral therapy of autistic children with mobile applications, specifically applied for measuring the child’s progress. A family of five applications is presented, that was developed as an investigation tool within the project aimed at automation of therapy progress monitoring. The applications were already tested with children with autism spectrum disorder. Hereby we analyse children’ experience...
-
The Analysis of Container Vessel Service Efficiency in the Aspect of Berth and Handling Equipment Usage in Polish Ports
PublikacjaThe paper analyses the efficiency of container vessel service in Polish container terminals taking under considerations different berth layouts and handling equipment.
-
Role of method of implementing multi-factorial falls prevention in nursing homes for elderly persons. The EUNESE project
Publikacja -
Nutrition in the age-related disablement process
Publikacja -
Sparse vector autoregressive modeling of audio signals and its application to the elimination of impulsive disturbances
PublikacjaArchive audio files are often corrupted by impulsive disturbances, such as clicks, pops and record scratches. This paper presents a new method for elimination of impulsive disturbances from stereo audio signals. The proposed approach is based on a sparse vector autoregressive signal model, made up of two components: one taking care of short-term signal correlations, and the other one taking care of long-term correlations. The method...
-
SUMMER SCHOOL: Arch Drawing 2/ Elective design II: CULTURAL HERITAGE ROUTES – GDAŃSK FORTIFICATION SYSTEM _2023
Kursy OnlineCultural Heritage Routes – Gdańsk Fortification System This course explores challenges, conflicts and concepts of cultural heritage preservation and protection in urban level, their connection to architectural and urban design in the time of digitalisation and their importance for a future of the cities. The aim of this course, based on the case study city of Gdańsk, is to understand the problem of cultural heritage and...
-
Comparative analysis of national and regional models of the silver economy in the European Union
Publikacja -
Listening to Live Music: Life beyond Music Recommendation Systems
PublikacjaThis paper presents first a short review on music recommendation systems based on social collaborative filtering. A dictionary of terms related to music recommendation systems, such as music information retrieval (MIR), Query-by-Example (QBE), Query-by-Category (QBC), music content, music annotating, music tagging, bridging the semantic gap in music domain, etc. is introduced. Bases of music recommender systems are shortly presented,...
-
Electron-impact ionization cross section calculations for 5-chloropyridine and 5-bromopyridine molecules
PublikacjaThe total cross sections for the single electron-impact ionization of 5-chloropyridine (5-C5H4ClN) and 5-bromopyridine (5-C5H4BrN) molecules have been calculated using binary-encounter-Bethe method for electron energies ranging from the ionization threshold up to 5 keV.
-
Electro-thermal buckling of elastically supported double-layered piezoelectric nanoplates affected by an external electric voltage
PublikacjaPurpose Thermal buckling of double-layered piezoelectric nanoplates has been analyzed by applying an external electric voltage on the nanoplates. The paper aims to discuss this issue. Design/methodology/approach Double-layered nanoplates are connected to each other by considering linear van der Waals forces. Nanoplates are placed on a polymer matrix. A comprehensive thermal stress function is used for investigating thermal buckling....
-
The level of VAT in relation to the GDP of selected European Union countries in 2007-2015 (in%)
Dane BadawczeVAT (Value Added Tax) is part of a strictly harmonized tax within the European Union. Under the so-called The Sixth Directive introduced provisions regulating the subject and subject of taxation, tax exemptions and exclusions as well as the tax collection mechanism in all Member States.
-
EXPERIMENTAL VERIFICATION OF THE METHOD OF FLOW BOILING AND FLOW CONDENSATION HEAT TRANSFER PREDICTION FOR SELECTED FLUIDS
PublikacjaIn the paper presented are the results of calculations using authors own model to predict heat transfer coefficient during flow boiling of different refrigerants. The experimental data from various research studies from literature were collected. Calculations were conducted for a full range of quality variation and a wide range of mass velocity. The aim of the study was to test the sensitivity of the in- house developed model....
-
The ONETEP linear-scaling density functional theory program
PublikacjaWe present an overview of the ONETEP program for linear-scaling density functional theory (DFT) calculations with large basis set (planewave) accuracy on parallel computers. The DFT energy is computed from the density matrix, which is constructed from spatially localized orbitals we call Non-orthogonal Generalized Wannier Functions (NGWFs), expressed in terms of periodic sinc (psinc) functions. During the calculation, both the...
-
Józef Woźniak prof. dr hab. inż.
OsobyProf. dr hab. inż. Józef Woźniak prof. zw. Politechniki Gdańskiej ukończył studia na Wydziale Elektroniki Politechniki Gdańskiej w 1971 r. W 1976 r. uzyskał stopień doktora nauk technicznych, a w 1991 r. stopień doktora habilitowanego w dyscyplinie telekomunikacja i specjalności teleinformatyka. W styczniu roku 2002 otrzymał tytuł profesora nauk technicznych. W 1994 r. został mianowany na stanowisko profesora nadzwyczajnego w Politechnice...
-
Cross-cultural problem of quality
PublikacjaThe paper, by presenting issues such as variability of reality, quality of life, quality and environmental management systems, emphasizes the opportunities of taking the socially important problem under control by utilization of efficient quality engineering analytical methods.
-
Modeling and Evaluation of Electric Treeing Phenomena in Polymeric Cable Insulation
PublikacjaThis paper investigates the treeing phenomenon in polymeric materials such as crosslinked polyethylene (XLPE) that is widely used in medium and high voltage power cables as primary insulation. The modeling of electrical tree growth in the insulation from its initiation to breakdown is significant research work that illustrates the discharge dynamics and its impact on aging process in polymeric insulation. This study utilizes pulse...
-
Elderly persons professional activity - substantive issues and methodological challenges
PublikacjaPopulation ageing in Europe and mass withdrawal from professional activity leads to a number of adverse phenomena, such as increased public spending, reduced consumer demand and the growing problem of social exclusion. The study focuses on the problems of population ageing in Europe as well as on the feasible steps that may be taken with a view to professional activation of the elderly. The first part is concerned with the trends...
-
Modelling of network schedule including priority of selected technical resources
PublikacjaThe paper presents a method of network planning CPM – Critical Path Method. The author compares models of optimal solutions to design deadlines for individual works, taking various leading technical resources such as is labor and a tower crane into account.
-
Photovoltaic properties of cadmium selenide–titanyl phthalocyanine planar heterojunction devices
PublikacjaPhotovoltaic phenomenon taking place in cadmium selenide (CdSe)/titanyl phthalocyanine (TiOPc) planar heterojunction devices is described. Mechanisms of free charge carrier generation and their recombination in the dark and under illumination are analyzed, chosen photovoltaic parameters are presented.
-
Problems of construction projects regarding historic road bridges
PublikacjaThe paper describe the comparison of different approaches to reconstruction and the problems in the selection of implementation for a historic bridge over the Vistula River in Tczew. A compromise reconstruction is shown, taking technical, historical and aesthetic aspects into account, as well as needs of the local community.
-
The Effect of Polyurethane Glycolysate on the Structure and Properties of Natural Rubber/Carbon Black Composites
PublikacjaIn this work the use of polyurethane chemical recycling product (i.e. glycolysis of polyurethane waste realized with the mass excess of polymer) as a plasticizer for natural rubber-based composites was proposed. The effect of plasticizer type (napthenic oil and polyurethane foam glycolysate) and amount (2, 4, 6 or 8 parts per 100 parts of natural rubber) on the processing properties of rubber mixtures and chemical structure, swelling,...
-
Analysis of the influence of ferromagnetic contaminations in plastics on the measurements of disturbances of magnetic field of the Earth
PublikacjaPlastics can be contaminated with small particles or filings with ferromagnetic properties. These contaminations cause significant disturbances in the magnetic field in the case of taking measurements of very low magnetic fields. The analysis of the influence of contaminated plastics on magnetic measurements is presented in this paper.
-
Local buckling of thin-walled channel member flange made of aluminum alloy
PublikacjaThe paper deals with local stability of the thin-walled compressed flange of channel columns and beams made of aluminum alloy. The aim of paper is to find critical stress of local buckling of the flange member taking into account the web-flange interaction in linear and nonlinear elastic range of the member material. The governing differential equation of the problem is derived with aid of the principle of stationary total potential...
-
An analysis of observability and detectability for different sets of measured outputs - CSTR case study
PublikacjaA problem of proving the observability/detectability at a given measured output for non-linear biochemical systems has been addressed in this paper. A theory of indistinguishable state trajectories has been used to prove the properties of the observability or detectability of this system. It is related to taking system dynamics into consideration depending on initial conditions and the impact of inputs taking into account a given...
-
Fading Modeling in Maritime Container Terminal Environments
PublikacjaIn this paper, an analytical model for slow and fast fading effects in maritime container terminals is derived, from fitting distributions to the results of measurements performed in an actual operational environment. The proposed model is composed of a set of equations, enabling to evaluate fading statistical distribution parameters for different system and environments conditions, as a function of frequency, base station antenna...
-
Semantic Analysis and Text Summarization in Socio-Technical Systems
PublikacjaIn this chapter the authors present the results of the development the methodology for increasing the reliability of the functioning of the Socio-Technical System. The existed methods and algorithms for processing unstructured (textual) information were studied. Taking into account noted above strengths and weaknesses of Discriminant and Probabilistic approaches of Latent Semantic Relations analysis in of the summarization projection...
-
A mobile hospital – its advantages and functional limitations
PublikacjaThe idea of a mobile hospital is not entirely new – the need for their use, ranging from military field hospitals to the charity or mass disaster tent cities, shows how much they are needed. While these cases can be reduced to a portable ambulatory unit with a limited scope of outpatient medical activities, a fully functional hospital is a system with a high degree of complexity far exceeding a regime of compact objects. Solutions...
-
The influence of variants of finishing machining on scheduling of shaft components manufacturing
PublikacjaIn the paper variants of technological processes were presented to the study for piston rods and rams of hydraulic cylinders taking issues into consideration scheduling of course of the production in flexible manufacturing cell. At the carried study an attempt of the estimation of the influence of technological variants on the effectiveness to manufacture the flexible manufacturing system on the basis of preliminary schedules of...
-
The Impact of Sloshing Liquids on Ship Stability for Various Dimensions of Partly Filled Tanks
PublikacjaLiquid sloshing phenomenon taking place in partly filled ships' tanks directly affects the stability of a vessel. However, only static calculations are carried out onboard ships nowadays and static transfer of liquid weight is taken into account in the course of routine stability calculation. The paper is focused on a dynamic heeling moment due to liquid sloshing in tanks onboard ships. A number of numerical simulations of liquid...
-
A Method of Assessment of the Liquid Sloshing Impact on Ship Transverse Stability
PublikacjaLiquid sloshing phenomenon taking place in partly filled ships? tanks directly affects the stability of a vessel. However, only static calculations are carried out onboard ships nowadays and static transfer of liquid weight is taken into account in the course of routine stability calculation. The paper is focused on a dynamic heeling moment due to liquid sloshing in tanks onboard ships. The set of numerical simulations of liquid...
-
Hydrophobic deep eutectic solvents as “green” extraction media for polycyclic aromatic hydrocarbons in aqueous samples
PublikacjaThe paper presents novel nonionic and hydrophobic deep eutectic solvents which were synthesized from natural compounds, i.e., thymol, ±camphor, decanoic and 10-undecylenic acids. Fundamental physicochemical properties of the synthesized deep eutectic solvents were determined, followed by their application as extractants in ultrasound-assisted dispersive liquid-liquid microextraction to isolate and enrich polycyclic aromatic hydrocarbons...
-
Synthesis and thermal studies of flexible polyurethane nanocomposite foams obtained using nanoclay modified with flame retardant compound
PublikacjaThis work presents thermal studies of nanocomposites based on the flexible polyurethane (PU) matrix and filled using montmorillonite organically modified with organophosphorus flame retardant compound. Flexible PU nanocomposite foams were prepared in the reaction carried out between reactive alcoholic hydroxyl and isocyanate groups with the ratio of NCO to OH groups equal to 1.05. The amount of an organoclay ranging from 3 to 9...
-
The calculation long-term physical field created by water flow around the ship
PublikacjaThe paper presents a description of the problems with fluid flow around a ship. Using the described solution of the problem were performed numerical calculations using the boundary element method. Were also presented preliminary results of the calculation of pressure fields at the bottom of the ship, taking into account the impact of the bottom.
-
Bending of a Three-Layered Plate with Surface Stresses
PublikacjaWe discuss here the bending deformations of a three-layered plate taking into account surface and interfacial stresses. The first-order shear deformation plate theory and the Gurtin-Murdoch model of surface stresses will be considered and the formulae for stiffness parameters of the plate are derived. Their dependence on surface elastic moduli will be analyzed.
-
CSR in Polish SMEs from the Women Perspective
PublikacjaThis paper presents the implementation of the CSR approach among Polish small and medium enterprises, taking into account gender issues. It offers also a kind of evaluation of the national context of women entrepreneurship combined with a wider and deeper analysis of the CSR solutions that may be adressed to both, women, workers and women entrepreneurs.
-
Measurement of distance, velocity and angle of arrival using FMCW-CW combined waveform
PublikacjaA procedure of tacking small flying object based on a general principle of FMCW and Doppler radar is presented. In order to increase measurement range, this technique uses active signal source on the moving object. For simultaneous measurements of distance, radial velocity and direction (AoA) as well as simplified synchronization a combined FMCW-CW waveform is proposed. The presented measurement system was realized and verified...
-
ELECTRON-IMPACT IONIZATION CROSS SECTIONS CALCULATIONS FOR PURINE AND PYRIMIDINE MOLECULES
PublikacjaCross sections for electron-impact ionization of purine and pyrimidine molecules have been calculated using binary-encounter-Bethe method for electron energies ranging from the ionization threshold up to 5 keV. Ionization cross section for purine molecules is 1.4 times higher than for pyrimidine molecules. Acceptable agreement between experimental and theoretical ionization data for pyrimidine molecule has been found.
-
Durability evaluation of technical fabrics
PublikacjaA thorough examination of the influence of the conditions of use on the mechanical properties of technical fabrics is proposed. Laboratory experiments (uniaxial tensile, rheological, cyclic and biaxial tensile tests) have been conducted and the material’s parameters for Finite Element Method (FEM) simulations have been identified. Various constitutive models of technical fabrics are investigated and compared. On the basis of these...
-
Simulation of the number of storm overflows considering changes in precipitation dynamics and the urbanisation of the catchment area: a probabilistic approach
PublikacjaThis paper presents a probabilistic methodology that allows the study of the interactions between changes in rainfall dynamics and impervious areas in urban catchment on a long- and short-term basis. The proposed probabilistic model predict future storm overflows while taking into account the dynamics of changes in impervious areas and rainfall. In this model, a logistic regression method was used to simulate overflow resulting...
-
Landscape of Automated Log Analysis: A Systematic Literature Review and Mapping Study
PublikacjaLogging is a common practice in software engineering to provide insights into working systems. The main uses of log files have always been failure identification and root cause analysis. In recent years, novel applications of logging have emerged that benefit from automated analysis of log files, for example, real-time monitoring of system health, understanding users’ behavior, and extracting domain knowledge. Although nearly every...
-
District development concept – Lower Sopot (Dolny Sopot) district case study, study proposal no 1, May 2021
Dane BadawczeThe data presents results of work within the studies of the concept of development of the district in the context of the city, Lower Sopot (Dolny Sopot) district, study proposal no 1, from May 2021. The goal of the research process was to present the development concept of the area located in Lower Sopot (Dolny Sopot) district in the context of the...
-
Functional and spatial structure analysis – Lower Sopot (Dolny Sopot) district case study, study proposal no 1, February 2021
Dane BadawczeThe data presents results of work within the studies of the conditions of the district in the context of the city, Lower Sopot (Dolny Sopot) district, study proposal no 1, from February 2021. The goal of the research process was to present the functional and spatial structure analysis of the area located in Lower Sopot (Dolny Sopot) district in the...
-
Introductory CDIO Project 2022/2023
Kursy OnlineThe aim of this course is to make the students familiar with the team work to design, build and test simple electronic circuit. Also, how to write technical and engineering documentation taking in consideration electrical engineering, electronics, CAD and PCB design and computer simulation problems.
-
Introductory CDIO Project [Energy Technologies][2020/21]
Kursy OnlineThe aim of this course is to make the students familiar with the team work to design, build and test simple electronic circuit. Also, how to write technical and engineering documentation taking in consideration electrical engineering, electronics, CAD and PCB design and computer simulation problems.