Filters
total: 2262
filtered: 1862
displaying 1000 best results Help
Search results for: AL MATRIX COMPOSITE
-
Inorganic membrane: a game changer for gas separation and purification
PublicationThis review explores the advancements and remaining challenges in inorganic membrane science, particularly focusing on their potential for industrial applications. It delves into the fundamental principles of inorganic membrane design, fabrication, and characterization techniques. The review also critically analyzes key challenges faced by inorganic membranes, such as physical aging, plasticization, defective formation, and fouling....
-
Analysis of airborne metal containing particles with EDX/EDS detectorsin electron microscopes
PublicationIn years 2006-2010 particulate matter analysis was undertaken for dust samples collected from Gdansk and London area in orderto compare their morphology and composition. Part of those studies was devoted to analysis of particulate matter (PM) bearingmetals. Characterization of the morphology and size of the particles collected onto the filters was performed using a scanning electronmicroscope (SEM) and transmission electron microscope...
-
Combining CDKN1A gene expression and genome-wide SNPs in a twin cohort to gain insight into the heritability of individual radiosensitivity
Publication -
Machinability investigation in electric discharge machining of carbon fiber reinforced composites for aerospace applications
Publication -
Operational control on environmental safety of potentially toxic elements during thermal conversion of metal-accumulator invasive ragweed to biochar
Publication -
Synthesis and Testing of BCZY/LNZ Mixed Proton–electron Conducting Composites for Fuel Cell Applications
PublicationA composite of BaCe0.6Zr0.2Y0.2O3–δ and Li2O:NiO:ZnO was investigated for fuel cell applications. The composite was successfully synthesized and its phase stability was confirmed at temperatures up to 900 °C. The influence of sintering and pressing aids on density was also investigated. Electrical properties were measured. DC electrical conductivity was about 8•10-4 S/m at 845 K. Open circuit voltage measurements in wet hydrogen...
-
Waste tire rubber as low-cost and environmentally-friendly modifier in thermoset polymers – a review
PublicationNowadays, waste tire rubber (WTR) management is a growing and serious problem. Therefore, research works focused on the development of cost-effective and environmentally-friendly methods of WTR recycling are fully justified. Incorporation of WTR into polymer matrices and composite materials attracts much attention, because this approach allows sustainable development of industrially applicable waste tires recycling technologies....
-
Modification of thermal and rheological characteristics of bitumen by waste PET/GTR blends
PublicationWaste poly(ethylene terephthalate) (wPET)/ground tire rubber (GTR) blends with variable compositions were applied as low-cost modifiers into bitumen and their performance has been evaluated via morphological, thermal and rheological analyses. Depending on the weight ratio of wPET/GTR, dispersion of single/composite domains of waste polymers in the bitumen has promoted the interaction between bitumen and blend components. Fourier...
-
Electromodulation of photoluminescence in vacuum-evaporated films of fac-tris(2-phenylpyridine)iridium(III)
PublicationZaobserwowano silne wygaszenie fosforescencji w komórkach sandwiczowych Al/Ir(ppy)3/Al/kwarc, które w polu elektrycznym o natężeniu 3 MV/cm dochodzi do 30%. Mechanizm wygaszania jest związany z dysocjacją ekscytonów trypletowych pod działaniem zewnętrznego pola elektrycznego w obszarach zdefektowanych sieci krystalicznej.
-
Secure Quaternion Feistel Cipher for DICOM Images
PublicationAn improved and extended version of a quaternion-based lossless encryption technique for digital image and communication on medicine (DICOM) images is proposed. We highlight and address several security flaws present in the previous version of the algorithm originally proposed by Dzwonkowski et al. (2015). The newly proposed secure quater- nion Feistel cipher (S-QFC) algorithm...
-
Laser Welding of UNS S33207 Hyper-Duplex Stainless Steel to 6061 Aluminum Alloy Using High Entropy Alloy as a Filler Material
PublicationThe high entropy alloy (HEA) filler used during the fabrication method determines the reliability of HEAs for steel-aluminum dissimilar alloy configuration. HEAs have a direct impact on the formation of intermetallic compounds (IMC) formed by the interaction of iron (Fe) and aluminum (Al), and influence the size of the joint’s interaction zone. A novel welding process for Fe-Al alloy joints was developed to prevent the development...
-
Kompozytowy most dla pieszych. Badania doświadczalne i przygotowanie do projektowania
PublicationDysertacja powstała w ramach grantu badawczego NCBiR, pt. „Opracowanie kompozytowych przęseł mostów dla pieszych do zastosowania nad drogami GP”, nr PBS1/B2/6/2013. Głównym celem pracy było wsparcie procesu projektowania kompozytowego mostu pieszo-rowerowego. Zakres pracy obejmuje badania doświadczalne elementów kompozytowych GFRP, walidację modeli obliczeniowych oraz wykorzystanie aparatu analizy wrażliwości do procesu projektowego....
-
Tailoring diamondised nanocarbon-loaded poly(lactic acid) composites for highly electroactive surfaces: extrusion and characterisation of filaments for improved 3D-printed surfaces
PublicationA new 3D-printable composite has been developed dedicated to electroanalytical applications. Two types of diamondised nanocarbons - detonation nanodiamonds (DNDs) and boron-doped carbon nanowalls (BCNWs) - were added as fillers in poly(lactic acid) (PLA)-based composites to extrude 3D filaments. Carbon black served as a primary filler to reach high composite conductivity at low diamondised nanocarbon concentrations (0.01 to 0.2...
-
An Aqueous Exfoliation of WO3 as a Route for Counterions Fabrication—Improved Photocatalytic and Capacitive Properties of Polyaniline/WO3Composite
PublicationIn this paper, we demonstrate a novel, electrochemical route of polyaniline/tungsten oxide (PANI)/WO3) film preparation. Polyaniline composite film was electrodeposited on the FTO (fluorine-doped tin oxide) substrate from the aqueous electrolyte that contained aniline (monomer) and exfoliated WO3 as a source of counter ions. The chemical nature of WO3 incorporated in the polyaniline matrix was investigated using X-ray photoelectron...
-
Molecular Characterization of a Novel Lytic Enzyme LysC from Clostridium intestinale URNW and Its Antibacterial Activity Mediated by Positively Charged N-Terminal Extension
Publication -
Environmental risk, toxicity, and biodegradation of polyethylene: a review
Publication -
The effect of hybridization of fire retarded epoxy/flax-cotton fiber laminates by expanded vermiculite: Structure-property relationship study
PublicationThe study describes the hybridization of epoxy/flax-cotton (EP/FF) composites containing ammonium polyphosphate (APP) with micrometric expanded vermiculite (VMT) (1–10 wt%). The efficiency of hybridization of flame retarded epoxy/flax-cotton composites was assessed by performing static tensile and flexural strength evaluation, supplemented by impact strength measurements of the composites. Moreover, thermal and thermomechanical...
-
Chemical surface etching methods for ground tire rubber as sustainable approach for environmentally-friendly composites development– a review
PublicationGround tire rubber (GTR) has been used as a sustainable low-cost modifier in various composites. However, due to the hydrophobic nature of GTR, it is in compatible with most matrices and results in deterioration in both mechanical and physical properties of composites. This necessitates pre-modification of the powdered rubber to improve the interfacial bonding at the rubber-matric interface. The most common GTR modification research...
-
Super tough interpenetrating polymeric network of styrene butadiene rubber‐poly (methyl methacrylate) incorporated with general purpose carbon black ( N660 )
PublicationA classic set of polymeric interpenetrating polymeric network (IPN) microcomposites has been fabricated using an elastomer—styrene butadiene rubber [SBR], a thermoplastic poly(methyl methacrylate)-PMMA and with carbon black (CB)-N660 as a filler and reinforcing agent. This synthesized IPN composite can be promisingly employed as a toughened plastic and vibrational damper in a wide service range with excellent thermal stability,...
-
Impact Behaviour of Glass Fribre /Epoxy Composites with Nano-Enhanced Resin after Water Exposure
PublicationImpact behaviour of glass fibre /epoxy composites with nano- SiO2 modified resin was studied in terms of low velocity impact after water exposure. Nanocomposites with 1%, 2%, 3% 5% 7% nano-SiO2 (Nanopox- Evonic) were investigated. Peak impact load and impact damage area as a function of nanoparticle contents were compared for dry specimens and for samples exposed to water (0.7 %wt. 1.7% water absorbed) at 1J, 2J 3J impact energies....
-
Internal electric fields in vacuum-evaporated films as studied by electroabsorption spectroscopy
PublicationMierzono sygnały elektroabsorpcji na I-szej harmonicznej częstości przykładanego sinusoidalnego pola elektrycznego w komórkach sandwiczowych Al/warstwa organiczna/Al. Wyznaczono elektryczne pola wewnętrzne (Fi) dla materiałów stosowanych w organicznych diodach elektroluminescencyjnych (TPD, TAPC, MTDATA, QAC, Alq3, Ir(ppy)3, PtOEP). Mechanizm powstawania pól Fi powiązano z pułapkowaniem ładunku w obszarach przyelektrodowych.
-
SnO2 nanoparticles embedded onto MoS2 nanoflakes - An efficient catalyst for photodegradation of methylene blue and photoreduction of hexavalent chromium
PublicationIn this work, a molybdenum disulfide/tin oxide (MoS2/SnO2) composite was successfully prepared via a hydrothermal method. The MoS2/SnO2 composite was used as a photocatalyst for photoreduction of hexavalent chromium and photodecomposition of methylene blue. It exhibited higher photocatalytic performance under simulated solar light irradiation than MoS2 itself. The obtained material was characterized by several spectroscopic and...
-
Review on friction stir welding of dissimilar magnesium and aluminum alloys: Scientometric analysis and strategies for achieving high-quality joints
PublicationMagnesium and aluminum alloys continually attract interest as lightweight structural materials for transport applications. However, joining these dissimilar alloys is very challenging. The main obstacle that hinders progress in dissimilar Mg-Al joining is the formation of brittle intermetallic compounds (IMCs). As a solid-state joining technique, FSW is an excellent candidate to attenuate the deleterious IMC effects in dissimilar...
-
Materiały dla jednowarstwowych ogniw paliwowych
PublicationA composite material, which may be further applied as a single layer fuel cell, was synthesizes using solid state synthesis method. Composite consisted of two components. The first was a nanoeramic proton conductor - calcium doped lanthanum niobate. The second one was a nanoceramic semiconductor oxide composed of lithium, nickel and zinc oxides respectively.
-
Electrode materials for electrochemical capacitors based on poly(3,4-ethylenedioxythiophene) and functionalized multi-walled carbon nanotubes characterized in aqueous and aprotic electrolytes
PublicationWithin this work, we report a facile one-stage synthesis of nanocomposites based on functionalized carbon nanotubes (CNTs) and electroactive polymer poly(3,4-ethylenedioxythiophene). Three different composites are investigated as potential electrode materials for the electrochemical capacitors. Two of the composites contain carbon nanotubes (ox-CNTs), functionalized by acid oxidation process (65% HNO3, 120 °C). The third composite...
-
Niekonwencjonalne koła pojazdów
PublicationPrzedstawiono sposoby zapobiegania skutkom utraty ciśnienia w oponach pneumatycznych. Zaprezentowano koła niepneumatyczne, zastosowane w pojeździe księżycowym. Omówiono wyniki badań kół kompozytowych. Przedstawiono najnowsze rozwiązania konstrukcyjne koł niepneumatycznych przeznaczonych do pojazdów mechanicznych.
-
Badania doświadczalne segmentu walidacyjnego kompozytowej kładki pieszo-rowerowej
PublicationW artykule przedstawiono zakres badań zrealizowanych na segmencie walidacyjnym o długości ~3 m będącym wycinkiem docelowej kompozytowej, powłokowej kładki pieszo-rowerowej. Wykonane testy statyczne i dynamiczne pozwoliły na ocenę pracy konstrukcji i potwierdziły przyjęte na etapie projektowania założenia teoretyczne.
-
Load capacity and serviceability conditions for footbridges made of fibre-reinforced polymer laminates = Warunki nośności i użytkowalności w odniesieniu do kładek z laminatów polimerowych
PublicationThe contribution is focused on derivation of the Ultimate Limit State (ULS) and Serviceability Limit State (SLS) design criteria for footbridges built of fibre-reinforced polymer matrix (FRP) laminates. The ULS design criterion is based on the design guidelines for above-ground, pressure, FRP composite tanks and the Tsai-Wu failure criterion, which is used to predict the onset of FRP laminates damage. The SLS criterion is based...
-
Ultrasound assisted dispersive solid phase microextraction using polystyrene-polyoleic acid graft copolymer for determination of Sb(III) in various bottled beverages by HGAAS
PublicationA new polyoleic acid-polystyrene (PoleS) block/graft copolymer was synthesized and applied as adsorbent for ultrasound assisted dispersive solid phase microextraction (UA-DSPME) of Sb(III) in different bottled beverages and analysis using hydride generation atomic absorption spectrometry (HGAAS). Adsorption capacity of the PoleS was 150 mg g−1. Several sample preparation parameters such as sorbent amount, solvent type, pH, sample...
-
Investigation of corrosion behavior of 6060 and 6082 aluminum alloys under simulated acid rain conditions
PublicationInstantaneous impedance changes of 6060 and 6082 type aluminum alloys in pure water, and simulated acid rain poured into the pure water was investigated by dynamic electrochemical impedance spectroscopy (DEIS). In this way, the influence of aluminum content on the corrosion behavior of 6060 and 6082 type aluminum alloys immersed in simulated acid rain was determined. The corrosion rate of the alloy decreased with increasing Al...
-
The Efficiency of Polish Stock Market: Ordinal Patterns Approach
PublicationZunino et al. analyzed the problem of discrimination of developed and emergent markets by the use of ordinal patterns methods: number of forbidden patterns and ordinal pattern probability distribution as a basis for entropy and statistical measure of complexity. In this paper we apply the same methodology for the analysis of Polish stock market (index WIG). The results indicate that Polish market belongs neither to developed, nor...
-
Distillery Wastes as External Carbon Sources for Denitrification in Municipal Wastewater Treatment Plants
PublicationIn order to improve efficiency of N removal within the existing capacities, the denitrification process can be enhanced by adding external carbon sources. The studies on utilization of various by-products or waste materials as alternative carbon sources for denitrification have been carried out for over 20 years (Sage et al. 2006). Among several commercially available organic compounds (such as methanol, ethanol, acetic acid, glucose),...
-
LabVIEW-based intelligent system of protection against electric shock for photovoltaic installations
PublicationEvaluation of shock hazard in installations with photovoltaic sources of energy is more complicated than in a conventional low voltage system. In case of earth fault in photovoltaic generators, that are connected to the AC power public grid, a composite waveform of earth fault current in the installation may occur. For composite waveforms, the safety criteria should be modified. The paper considers the effect of the composite waveforms...
-
Proposed approaches for coronaviruses elimination from wastewater: Membrane techniques and nanotechnology solutions
Publication -
The Role of Dopaminergic Genes in Probabilistic Reinforcement Learning in Schizophrenia Spectrum Disorders
Publication -
Confirmation Bias in the Course of Instructed Reinforcement Learning in Schizophrenia-Spectrum Disorders
Publication -
Enhanced supercapacitor materials from pyrolyzed algae and graphene composites
PublicationThis study focuses on the synthesis and characterization of supercapacitor materials derived from pyrolyzed natural compounds. Four compounds were investigated: methylcellulose with lysine (ML), methylcellulose with lysine-graphene composite (MLG), algae (A), and algae-graphene composite (AG). The pyrolysis process was utilized to convert these natural compounds into carbon-based materials suitable for supercapacitor applications....
-
Conductive Thermoplastic Polyurethane Nanocomposite Foams Derived from a Cellulose/MWCNTs Aerogel Framework: Simultaneous Enhancement of Piezoresistance, Strength, and Endurance
PublicationHigh conductivity and excellent mechanical properties of composite polymers favors their application as piezoresistive strain sensors. Nonetheless, it is difficult to develop composite polymers with desirable piezoresistance, mechanicaland durable properties. Herein, we developed conductive cellulose/MWCNTs aerogel using the freeze-drying technique. Besides, we explored the application of the highly-sensitive piezoresistive polymer...
-
Cement composites with expanded graphite as resistance heating elements
Publication -
Water absorption and blistering of glass fibre-reinforced polymer marine laminates with nanoparticle-modified coatings
PublicationMacro and microstructural damage was studied in typical glass fibre-reinforced polymer laminates with two types of coating systems – (a) isophtalic gel coat: pure or mixed with SiO2 nanoparticles 5 wt% (5%N) or 10 wt% (10%N) and (b) a two-layer coating system: urethane-modified vinyl ester-based gel coat and additional polyester barrier coat layer. Accelerated tests were performed at 50C for 50 days for specimens with nanoparticle-modified...
-
Material characterisation of biaxial glass-fibre non-crimp fabrics as a function of ply orientation, stitch pattern, stitch length and stitch tension
PublicationDue to their high density-specific stiffnesses and strength, fibre reinforced plastic (FRP) composites are particularly interesting for mobility and transport applications. Warp-knitted non-crimp fabrics (NCF) are one possible way to produce such FRP composites. They are advantageous because of their low production costs and the ability to tailor the properties of the textile to the reinforcement and drape requirements of the application....
-
Structural and physico-mechanical properties of natural rubber/GTR composites devulcanized by microwaves: Influence of GTR source and irradiation time
PublicationGround tire rubber from car and truck was modified using microwave irradiation at variable time. The irradiated ground tire rubber was used as filler in composites based on natural rubber. The composites, with high content of ground tire rubber, were prepared using an internal batch mixer and subsequently cross-linked at 160℃. The influence of the ground tire rubber source (car/truck) and irradiation time on structure, physico-mechanical...
-
Stability analyses of a cylindrical steel silo with corrugated sheets and columns
PublicationW artykule przedstawiono wyniki obliczeń stateczności silosów z blachy falistej ze słupami. Wykonano analizy linowe i analizy nieliniowe stosując metody elementów skończonych. W obliczeniach uwzględniono model przestrzenny powłokowy oraz uproszczony model przestrzenny z blachy ortotropowej z belkami. Wyniki numeryczne porównano z Eurokodem.
-
Reliable method of assessing fracture properties of asymmetric bonded joints
PublicationTwo methods of assessing fracture properties of adhesive joints were studied. Two wedge tests: with continuous deflection and with force measurements were compared. Asymmetric geometry of the bonded joint was considered, i.e. two different plates of aluminium alloys: Al-Cu and Al-Mg, were bonded with epoxy DGEBA adhesive. The analytical model is shown to estimate the values of fracture properties: crack position and critical fracture...
-
O modelowaniu numerycznym dźwigarów zespolonych
PublicationThe paper is a general review of theoretical problems and corresponding numerical procedures actually available in commercial engineering software. Several possibilities of numerical simulation for composite girders are presented. Effectivity of meshing is showed on the simple example. Finally several examples of structural numeric models for real bridges are included. In the author's opinion, presented available procedures for...
-
A novel approach in wood waste utilization for manufacturing of catalyst-free polyurethane-wood composites (PU-WC)
PublicationIn recent decades, due to the increase in environmental awareness and noticeable environmental degradation, the area of wood waste management has attracted increasing attention. The purpose of this study is to develop a new type of highly filled polyurethane wood-composite (PU-WC) by the utilization of large amount of wood wastes without addition of a catalyst. Although wood-plastic composites (WPCs) are widely known, there is...
-
Selection of circuit geometry for miniaturized microwave components based on concurrent optimization of performance and layout area
PublicationThe paper presents a framework for automated EM-driven circuit geometry selection of miniaturized microwave components. Selection of a particular layout is based directly on miniaturization rates achieved for a set of candidate circuit geometries. Size reduction of the considered structures is obtained by replacing their main building blocks (i.e., conventional transmission lines) with slow-wave composite cells and meander lines....
-
Mechanical Performance and Environmental Assessment of Sustainable Concrete Reinforced with Recycled End-of-Life Tyre Fibres
PublicationThe presented research’s main objective was to develop the solution to the global problem of using steel waste obtained during rubber recovery during the tire recycling. A detailed comparative analysis of mechanical and physical features of the concrete composite with the addition of recycled steel fibres (RSF) in relation to the steel fibre concrete commonly used for industrial floors was conducted. A study was carried out using...
-
Fractional neutron point kinetics equations for nuclear reactor dynamics – Numerical solution investigations
PublicationThis paper presents results concerning numerical solutions to a fractional neutron point kinetics model for a nuclear reactor. The paper discusses and expands on results presented in (Espinosa-Paredes et al., 2011). The fractional neutron point kinetics model with six groups of delayed neutron precursors was developed and a numerical solution using the Edwards’ method was proposed (Edwards et al., 2002). The mathematical model...
-
Efektywność flotacji jonowej i precypitacyjnej mieszaniny jonów cynku i glinu
PublicationPrzedmiotem badań była ocena wpływu pH surówki oraz stężenia kolektora na efektywność półperiodycznych flotacji jonowej i precypitacyjnej, zachodzących w roztworach zawierających mieszaniny jonów Zn(II) i Al(III). Stwierdzono, iż w warunkach flotacji jonowej, zachodzących w roztworach kwaśnych, występuje konkurencja pomiędzy flotowanymi kationami w tworzeniu związków z kolektorem. Dla roztworów o pH>11 możliwa jest selektywna flotacja...