Search
Filters
total: 4093
filtered: 3184
displaying 1000 best results Help
Search results for: FRICTION-MECHANICAL TREATMENT
-
Thermo-Mechanical Simulation of Underwater Friction Stir Welding of Low Carbon Steel
PublicationThis article investigates the flow of materials and weld formation during underwater friction stir welding (UFSW) of low carbon steel. A thermo-mechanical model is used to understand the relation between frictional heat phenomena during the welding and weld properties. To better understand the effects of the water environment, the simulation and experimental results were compared with the sample prepared by the traditional friction...
-
Investigation of Mechanical and Microstructural Properties of Welded Specimens of AA6061-T6 Alloy with Friction Stir Welding and Parallel Friction Stir Welding Methods
PublicationThe present study investigates the effect of two parameters of process type and tool offset on tensile, microhardness, and microstructure properties of AA6061-T6 aluminum alloy joints. Three methods of Friction Stir Welding (FSW), Advancing Parallel-Friction Stir Welding (AP-FSW), and Retreating Parallel-Friction Stir Welding (RP-FSW) were used. In addition, four modes of 0.5, 1, 1.5, and 2 mm of tool offset were used in two welding...
-
Corrosion and Cavitation Resistances of Low Alloy Steel After Frictional-Mechanical Treatment
PublicationPaper presents the results of the studies of wear, corrosion and cavitation resistances of the S355J2 low alloy medium carbon steel subjected to surface modification by friction-mechanical treatment, as tested in sea water simulated solution. To evaluate the effect of the surface treatment, the comparative studies of the corrosive properties of the steel before and after treatment have been considered. The treatment due to a severe...
-
Recycling of Waste Rubber by Thermo-Mechanical Treatment in a Twin-Screw Extruder
PublicationRecycling of waste tires is a significant issue considering both environmental and economic aspects. One of the leading recycling routes is the shredding of tires resulting in the generation of ground tire rubber. This material can be easily introduced into various polymer matrices as a filler, reducing the use of conventionally applied petroleum-based materials. In such cases, it is essential to ensure sufficient interfacial compatibility,...
-
The effectiveness of the mechanical treatment of municipal waste using the example of a selected installation
Publication -
Temperature Evolution, Material Flow, and Resulting Mechanical Properties as a Function of Tool Geometry during Friction Stir Welding of AA6082
PublicationThe friction stir welding process was simulated for joining AA6082 aluminum alloy with the use of the computational fluid dynamics method. Two different tool geometries were used—a tapered cylindrical pin (simple pin) and a hexagonal pin with grooves (complex pin). The analysis of the simulations performed was discussed in terms of temperature evolution during the process, total heat input, residual stresses and material flow....
-
The Influence of Tool Shape and Process Parameters on the Mechanical Properties of AW-3004 Aluminium Alloy Friction Stir Welded Joints
PublicationThe purpose of the following study was to compare the effect of the shape of a tool onthe joint and to obtain the values of Friction Stir Welding (FSW) parameters that provide the bestpossible joint quality. The material used was an aluminium alloy, EN AW-3004 (AlMn1Mg1). To theauthors’ best knowledge, no investigations of this alloy during FSW have been presented earlier. Fivebutt joints were made with a self-developed, cylindrical,...
-
Sustainable upcycling of brewers’ spent grain by thermo-mechanical treatment in twin-screw extruder
PublicationThermo-mechanical treatment of brewers’ spent grain (a by-product of beer manufacturing) was successfully performed via the extrusion process. The impact of temperature (from 30 to 180 °C), throughput (from 1 to 5 kg/h) and screw speed (from 75 to 375 rpm) on particle size, color, chemical structure, antioxidant activity and thermal stability of resulting material, as well as correlations between particular properties, were investigated....
-
Effect of Laser Treatment on Intrinsic Mechanical Stresses in Titanium and Some of Its Alloys
PublicationLaser surface treatment conducted at different power levels is an option to modify titanium bone implants to produce nano- and microtopography. However, such processing can lead to excess mechanical stress within the surface layer. This research aims to calculate the level of such residual stresses after the surface processing of Ti grade IV, Ti15Mo, and Ti6Al7Nb alloys with an Nd:YAG laser. Light and scanning electron microscopies...
-
Analysis of Potential Exposure to Components of Municipal Solid Waste in a Mechanical Biological Treatment
Publication -
The Effect of Cryogenic Treatment on Microstructure and Mechanical Response of AISI D3 Tool Steel Punches
PublicationRecently, deep cryogenic treatment is performed to improve the mechanical responses (wear, hardness, fatigue, and thermal conductivity) of various steel components. Researchers have tried to evaluate the eco-friendly and nontoxic process to optimize the parameters. Cold-shearing punches used to manufacture various holes that undergo severe impact loading and wear in the metal forming process. This study concerns the effect of soaking...
-
Influence of Surface Laser Treatment on Mechanical Properties and Residual Stresses of Titanium and its Alloys
PublicationSurface modification of the titanium and its alloys used in implantology with a long-pulse laser can change the surface topography, but it also leads to changes in the stress sign and magnitude in the resulting subsurface layer. The presented research was aimed at evaluating the state of stress after laser remelting with the Nd:YAG laser of pre-etched titanium alloys Ti6Al4V and Ti13Nb13Zr and pure titanium. The obtained surface...
-
Insights into the Thermo-Mechanical Treatment of Brewers’ Spent Grain as a Potential Filler for Polymer Composites
PublicationThis paper investigated the impact of twin-screw extrusion parameters on the properties of brewers’ spent grain. The chemical structure, antioxidant activity, particle size, and color properties, as well as the emission of volatile organic compounds during extrusion, were investigated. The main compounds detected in the air during modifications were terpenes and terpenoids, such as α-pinene, camphene, 3-carene, limonene, or terpinene....
-
Application of mechanical Barkhausen noise in assessment of X20 steel properties after heat treatment
Publication -
Poly(ε-Caprolactone)/Brewers’ Spent Grain Composites—The Impact of Filler Treatment on the Mechanical Performance
PublicationWaste lignocellulose materials, such as brewers’ spent grain, can be considered very promising sources of fillers for the manufacturing of natural fiber composites. Nevertheless, due to the chemical structure differences between polymer matrices and brewers’ spent grain, filler treatment should be included. The presented work aimed to investigate the impact of fillers’ reactive extrusion on the chemical structure and the poly(ε-caprolactone)/brewers’...
-
Hybrid Processing: the Impact of Mechanical and Surface Thermal Treatment Integration onto the Machine Parts Quality
Publication -
Influence of microwave treatment conditions of GTR on physico-mechanical and structural properties of NBR/NR/GTR composites
PublicationThe increasing amount of tires used in the industry induces the researchers to find alternatives to the recycling of the end-of-life tires. Several alternatives in order to application of ground tire rubber GTR include their incorporation as a filler in composites. The main issue in this approach is the lack of compatibility between GTR and polymer matrix. In order to solve this problem the devulcanization by microwaves has been...
-
Effect of Porosity on the Thermo-Mechanical Behavior of Friction-Stir-Welded Spark-Plasma-Sintered Aluminum Matrix Composites with Bimodal Micro- and Nano-Sized Reinforcing Al2O3 Particles
PublicationThe thermo-mechanical behavior of nanosized Al2O3 particles reinforcing aluminum was analyzed in the present paper. The material was prepared by spark plasma sintering and friction stir welding. The thermal stresses affecting the composite behavior during welding were modeled through COMSOL MultiPhysics, and the results were validated by the analyses of the composites’ mechanical properties. The spark-plasma-sintered materials...
-
Physical and Mechanical Evaluation of Silicone-Based Double-Layer Adhesive Patch Intended for Keloids and Scar Treatment Therapy
PublicationGrowing interest in silicone elastomers for pharmaceutical purposes is due to both theirbeneficial material effect for scar treatment and their potential as drug carriers. Regarding their morphological structure, silicone polymers possess unique properties, which enable a wide range of applicability possibilities. The present study focused on developing a double-layer adhesive silicone film (DLASil) by evaluating its physical...
-
Influence of retrogression and reaging (RRA) heat treatment on microstructure, mechanical and chemical behaviour of an Al-Zn-Mg alloy
PublicationBadano metodą stałego wolnego rozciągania w wodzie morskiej wpływ czasu i temperatury nawrotu oraz powtórnego starzenia na czas do zniszczenia, energię zniszczenia, przewężenie i odkształcenie. Stwierdzono ogólnie niewielki wpływ, przy czym wzrostowi odporności na korozję naprężeniową towarzyszył spadek właściwości mechanicznych. Obserwowane zmiany właściwości przypisano zmianom struktury dyslokacyjnej i mikrostruktury.
-
Physical and Mechanical Evaluation of Silicone-Based Double-Layer Adhesive Patch Intended for Keloids and Scar Treatment Therapy
Publication -
Effect of pulse laser treatment at different process variables on mechanical behavior of carbon nanotubes electrophoretically deposited on titanium alloy
PublicationPurpose: Titanium and its alloys are widely used as biomaterials for long-term implants, but they are usually surface-modified due to their weak bioactivity and wear resistance. Laser processing was used to modify the surface layer, and elemental carbon was a component of the deposited coatings. This research aims to use a combination of both methods based on preliminary electrophoretic deposition of multi-wall carbon nanotubes...
-
To what extent can hyperelastic models make sense the effect of clay surface treatment on the mechanical properties of elastomeric nanocomposites?
PublicationThe poor knowledge about nonlinear mechanical behavior of elastomer nanocomposites arises from the incomplete information on the interface. Application of hyperelastic models provides more insights into the nature and the situation of interaction between the elastomeric matrix and nanofillers. The current work seeks to address the effect of interphase strength on tensile properties of the elastomer nanocomposites under large deformations....
-
Fate and significance of phthalates and bisphenol A in liquid by-products generated during municipal solid waste mechanical-biological pre-treatment and disposal
PublicationSamples of liquid by-products generated by municipal solid waste plants (MSWPs) were tested for the presence of phthalates (PAEs) and bisphenol A (BPA). The results indicated that the wastewater generated during mechanical (sorting unit - SU) and biological (composting unit - CU) pre-treatment (MBT) of residual (mixed) solid waste is a significant source of these compounds. The concentrations of PAEs (up to 32222 lg/L) and BPA...
-
Validation of odor concentration from mechanical-biological treatment piles using static chamber and wind tunnel with different wind speed values
Publication -
Mechanical Properties and Residual Stress Measurements of Grade IV Titanium and Ti-6Al-4V and Ti-13Nb-13Zr Titanium Alloys after Laser Treatment
PublicationNowadays, surface engineering focuses on research into materials for medical applications. Titanium and its alloys are prominent, especially Ti-6Al-4V and Ti-13Nb-13Zr. Samples made of pure grade IV titanium and the titanium alloys Ti-6Al-4V and Ti-13Nb-13Zr were modified via laser treatment with laser beam frequency f = 25 Hz and laser beam power P = 1000 W during a laser pulse with duration t = 1 ms. Subsequently, to analyze...
-
Alkali-activated slag (AAS) and OPC-based composites containing crumb rubber aggregate: Physico-mechanical properties, durability and oxidation of rubber upon NaOH treatment
Publication -
Heavy metals removal in the mechanical - biological wastewater treatment plant ''Wschod'' in Gdańsk. Usuwanie metali ciężkich w mechaniczno-biologicznej oczyszczalni ścieków Gdańsk ''Wschód''.
Publication.
-
The impact of filler thermomechanical modifications on static and dynamic mechanical performance of flexible foamed polyurethane/ground tire rubber/zinc borate composites
PublicationThe rapid development of the automotive industry is very beneficial to many aspects of human life, but it is also a very significant environmental burden. The most straightforward impact is related to the generation of exhaust, but the management of post-consumer car parts is also a major challenge. Among them, waste tires are very burdensome due to their enormous numbers. Therefore, it is essential to develop novel, environmentally...
-
Mechanical Properties of a Dike Formed from a Soil-ash Composite
PublicationThe paper presents the research results on application of composite soils for dike construction. The composite soil is produced by mixing bottom ash (by-product of energetics) with dredged material (sand) taken from the mouth of The Vistula river. The optimum composite for dike core was chosen with respect to mechanical parameters: high internal friction angle, good compaction and reduced hydraulic conductivity. The test dike was...
-
Experimental study on the feasibility of alternative materials for tilting pad thrust bearings operating in transition to mixed friction
PublicationIn hydrodynamic bearings traditional bearing alloys: Babbitts and bronzes are most frequently utilized. Polymer sliding layers are sometimes applied as a valuable alternative. Hard diamond-like carbon (DLC) coatings, which are also considered for certain applications may show some advantages, as well. Although material selection is of secondary importance in a full film lubrication regime it becomes important in mixed friction...
-
The Application of Vibration Recording and Analysis in Tribological Research on Sliding Friction
PublicationThe paper reports on a tribological research on the macroscopic manifestation and characteristics of sliding friction. The aim of the task was to measure friction in lubricated sliding contacts and test the interactions between the environment (the test rig) and the experimental friction contact. Friction-induced vibrations were observed and studied as a manifestation of the process. The typical set of velocity and force/torque...
-
Analytical Study of Sliding Instability due to Velocity- and Temperature-Dependent Friction
PublicationThe instability of sliding causes deterioration of performance characteristics of tribosystems and is undesired. To predict its occurrence, the motion of a body of a one-degree-of-freedom system with friction is investigated about the steady sliding equilibrium position. The motion equation is formulated with the friction coefficient dependent on the sliding velocity and contact temperature changing due to transient heat conduction...
-
Influence of friction stir welding technological parameters on the properties of the joints of selected aluminum alloys
PublicationThe purpose of this dissertation was to determine the effect of friction stir welding technological parameters on the properties of selected aluminum alloy joints, with consideration of the residual stresses and dislocation density in the joints. The goal of the present work was also to produce defect-free joints with high mechanical and electrochemical properties. In the dissertation, similar welds of AA6082 alloy and dissimilar...
-
Effect of Pin Shape on Thermal History of Aluminum-Steel Friction Stir Welded Joint: Computational Fluid Dynamic Modeling and Validation
PublicationThis article studied the effects of pin angle on heat generation and temperature distribution during friction stir welding (FSW) of AA1100 aluminum alloy and St-14 low carbon steel. A validated computational fluid dynamics (CFD) model was implemented to simulate the FSW process. Scanning electron microscopy (SEM) was employed in order to investigate internal materials’ flow. Simulation results revealed that the mechanical work...
-
Pin Angle Thermal Effects on Friction Stir Welding of AA5058 Aluminum Alloy: CFD Simulation and Experimental Validation
PublicationThe friction stir welding (FSW) of tool pin geometry plays a critical role in the final properties of the produced joint. The tool pin geometry directly affects the generation of heat and the flow of internal materials during the FSW process. The effects of the FSW tool pin angle on heat generation and internal flow have not been quantitatively investigated in detail. In this manuscript, a validated Computational Fluid Dynamic...
-
Friction-Induced Oscillations of a Non-Asbestos Organic Pin Sliding on a Steel Disc
PublicationFriction-induced oscillations result in deterioration of performance of disc brakes and are generally undesired. We conduct experimental study of friction-induced oscillations in a non-asbestos organic material / steel pair used in disc brakes of motor vehicles. The tests are done by use of a pin-on-disc machine which has the pin sample supported on a deformable beam. The adjustable friction parameters are the disc velocity, contact...
-
Corrosion Properties of Dissimilar AA6082/AA6060 Friction Stir Welded Butt Joints in Different NaCl Concentrations
PublicationA solid-state friction stir welding method which is increasingly used in the marine and shipbuilding industry, has been developed to produce welds with high mechanical properties. In seawater, the oxide layer of aluminium is attacked by Cl− ions resulting in its disruption and formation of pitting corrosion. It is particularly important to determine the electrochemical properties of the produced welds and to evaluate the efect...
-
THE DETERMINATION OF ABRASION RESISTANCE OF SELECTED BIOMATERIALS FOR THE FRICTION PAIRS IN THE HIP JOINT ENDOPROSTHESIS
PublicationThe key requirement for the modern endoprosthesis is high durability of the friction components, which results in long and trouble-free operation in the human body. The durability of currently used endoprosthesis is often limited by tribological wear processes of friction components (e.g. between the head and the acetabular component in a hip joint endoprosthesis) [8, 19, 23, 24]. In order to compare the tribological wear, tribological...
-
Method of identification of the slide tribological system top layer condition by assessment of the t-02 four-ball tester friction node operation
Publicationa method is proposed of the assessment of t-02 four-ball tester friction node operation during extreme unit loads on the tribological system for identification of the top layer condition in that system lubricated with the tested lubricating oil. by identification of the friction node with a thermodynamic system, that operation is treated as an energy generating process of the created servo-layer structure. the friction node operation...
-
Effect of processing parameters on the cyclic behaviour of aluminium friction stir welded to spark plasma sintered aluminium matrix composites with bimodal micro-and nano-sized reinforcing alumina particles
PublicationUnderstanding the cyclic behaviour of Alumina reinforced Aluminium composites (Al-A2O3) was of critical importance, for their further application in the different industrial sectors. The present study is focussing on the cyclic behaviour of the Al-Alumina nanocomposite produced through the combination of spark plasma sintering (SPS) method and friction stir welding (FSW). The added Alumina with total content of 10% is the combination...
-
Induction Assisted Hybrid Friction Stir Welding of Dissimilar Materials AA5052 Aluminium Alloy and X12Cr13 Stainless Steel
PublicationThis research aimed to study the induction in-situ heated hybrid friction stir welding (IAFSW) method to join AA5052 aluminium alloy with X12Cr13 stainless steel (SS) to enhance joint strength. The potency of this method on the mechanical properties and microstructural characterizations were also investigated. The results show that the transverse tensile strength gained was 94% of the AA5052 base metal that is 229.5 MPa. This superior...
-
One-dimensional chaos in a system with dry friction: analytical approach
PublicationWe introduce a new analytical method, which allows to find chaotic regimes in non-smooth dynamical systems. A simple mechanical system consisting of a mass and a dry friction element is considered. The corresponding mathematical model is being studied. We show that the considered dynamical system is a skew product over a piecewise smooth mapping of a segment (the so-called base map). For this base map we demonstrate existence of...
-
Torque capacity of multidisc wet clutch with reference to friction occurrence on its spline connections
PublicationIn this article developed mathematical model that includes friction occurrence on spline connections is presented. The work also contains results of experimental research on torque capacity of multidisc wet clutch. These results are expressed as a function of contact pressure for different number of friction surfaces. Due to increased interest in research concerning multidisc wet clutches it is essential to determine impact of...
-
MECHANICAL PROPERTIES OF BOTTOM ASH – DREDGED MATERIAL MIXTURES IN LABORATORY TESTS
PublicationBottom ash from EC Gdańsk and dredged material taken from the mouth of The Vistula were mixed to form an engineering material used for dike construction. Mixtures with different bottom ash content were tested in laboratory to determine its basic physical and mechanical properties. The optimum bottom ash–dredged material mixture, built in the corps of the test dike, contains 70% of ash. The optimum bottom ash content in the mixture...
-
Theoretical study of thermofrictional oscillations due to negative friction-temperature characteristic
PublicationAnalytical study on oscillations of a body on a moving counterbody has been done by assuming imperfect frictional thermal contact and friction that decreases with contact temperature. It has been shown that stick-slip oscillation occurs due to decrease of friction coefficient when the body moves in the opposite direction to the counterbody. Dynamical characteristics, such as conditions for stable sliding and limit cycles, have...
-
Assessment of Corrosive Behaviour and Microstructure Characterization of Hybrid Friction Stir Welded Martensitic Stainless Steel
PublicationThis study examined the effect of induction heating on the microstructure and corrosion characteristics of hybrid friction stir welded AISI 410 stainless steel. Five joints have been produced with different friction stir welding parameters like welding speed, spindle speed, plunge depth, and induction power. Their microstructures were evaluated using a scanning electron microscope, and chemical composition was examined using...
-
Airborne wear particle emission from train brake friction materials with different contents of steel and copper fibres
PublicationThis study investigated the influence of the amount of steel and copper fibres in a train brake friction material on the tribological performance, emission intensity and characteristics of airborne wear particles. The particles were generated on a pin-on-disc tribometer under controlled friction and environmental conditions. It was found that the steel fibre results in a more intensive emission of 0.3–10 μm particles compared to...
-
Friction Stir Welding of Aluminum in the Aerospace Industry: The Current Progress and State-of-the-Art Review
PublicationThe use of the friction stir welding (FSW) process as a relatively new solid-state welding technology in the aerospace industry has pushed forward several developments in different related aspects of this strategic industry. In terms of the FSW process itself, due to the geometric limitations involved in the conventional FSW process, many variants have been required over time to suit the different types of geometries and structures,...
-
Torque Transmitted by Multi-plate Wet Clutches in Relation to Number of Friction Plates and Their Dimensions
PublicationIn the paper results of experimental tests on multi-plate wet clutch torque capacity for various diameters and numbers of friction plates are presented. Construction of an apparatus for laboratory tests of wet clutch engagement, drag torque and maximum torque is shown. Methodology of maximum torque capacity experiment and hydraulic circuit diagram, which supplies a motor and an actuator for the experiment are described. Analytically...