Search
Filters
total: 3514
-
Catalog
displaying 1000 best results Help
Search results for: ROTOR ANGLE CONTROL
-
IPMSM rotor position estimator based on analysis of phase current derivatives
PublicationThis paper describes an algorithm for estimation of IPMSM angular rotor position. The algorithm uses derivatives of motor phase currents resulting from PWM modulation to obtain the rotor position. The presented method is designed for medium- and high-speed range, since it is based on determination of the EMF vector. Algorithm is characterised by a very simple formulae. The calculation of rotor position is performed in every PWM...
-
Determination of binder-aggregate adhesion by contact angle measurement
PublicationThe key factor in asphalt pavement durability, especially in the presence of water, is adhesion of the bituminous binder to mineral aggregates. There are currently no standard laboratory test procedures that can quickly and accurately measure the strength of the interaction (bond) between the binder and aggregate. In this regard, to evaluate the adhesion force measurements based on the contact angle between the binder and the aggregate...
-
An Innovative Floating System with a Savonius Rotor as a Horizontal-Axis Wind Turbine
PublicationIn this project, an innovative wind turbine was designed for a floating plant. A large Savonius rotor was replaced with a double-rotor wind turbine implemented as a horizontal-axis turbine. This double rotor was positioned on the tip of a thrust plate and fixed to the deck of a catamaran. Simple 2D numerical simulations were performed to confirm the effectiveness of the concept. An analysis of the floating system configuration...
-
Noninvasive method for rotor fault diagnosis in inverter fed induction motor drive
PublicationThis article presents a proposal, simulation and experimental results of a noninvasive rotor fault diagnosis method for the inverter fed induction motor drive. Comparing to reported methods the proposed one does not require any load, rotor brake, slip, mechanical or electrical system physical modification e.g. machine disassembly and can be applied regardless the rotor speed measurement or estimation method.
-
Effective Friction Angle Of Deltaic Soils In The Vistula Marshlands
PublicationThis article presents the results of laboratory tests on soft, normally consolidated soils from the Vistula Marshlands. Samples of high-plasticity organic soils (muds) taken from 3.2–4.0 m and 9.5–10.0 m depth, as well as peat deposit at 14.0 m, are analysed. Presented case study confirms the applicability of the Norwegian Institute of Technology (NTH) method based on Cone Penetration Tests (CPTU) and allows for a conservative...
-
Euler tour lock-in problem in the rotor-router model
PublicationW pracy rozważano model eksploracji grafu nieskierowanego przez pojedynczego agenta, w którym sterowanie agentem odbywa się zgodnie z zasadą ''rotor-router'' (inaczej: ''Propp machine''). Porównano czas stabilizacji agenta do trajektorii w postaci cyklu Eulera dla różnych klas grafów, prowadząc rozważania w kontekście teorii gier. Przydział początkowych portów i wskaźników w modelu jest traktowany jako rozgrywka pomiędzy graczem...
-
Bounds on the cover time of parallel rotor walks
PublicationThe rotor-router mechanism was introduced as a deterministic alternative to the random walk in undirected graphs. In this model, a set of k identical walkers is deployed in parallel, starting from a chosen subset of nodes, and moving around the graph in synchronous steps. During the process, each node successively propagates walkers visiting it along its outgoing arcs in round-robin fashion, according to a fixed ordering. We consider...
-
INFLUENCE OF SURFACE CURVATURE ON SESSILE DROPLET CONTACT ANGLE OF NANOFLUIDS
PublicationThis paper deals with change in contact angle of droplets of three nanofluids, i.e. water-Al2O3, water-TiO2 and water-Cu. Nanoparticles were tested at the concentration of 0.01%, 0.1%, and 1% by weight. Although dispersants were not used to stabilize the suspension, the solutions tested exhibited satisfactory stability. Ultrasonic vibration was used in order to stabilise the dispersion of the nanoparticles. Experimental measurements...
-
Magdalena Gajewska prof. dr hab. inż.
PeopleMagdalena Gajewska (born June 1th 1968 in Gdańsk) in 1993 graduated Hydro-Engineering Faculty at Gdańsk University of Technology. At present she is an assistant professor in the Department of Water and Wastewater Technology at the Faculty of Civil and Environmental Engineering GUT. PhD (2001) and habilitation (2013) in the discipline of environmental engineering. In the 2016-2020 term, serves as Vice -dean for science. She...
-
Nonadaptive estimation of the rotor speed in an adaptive full order observer of induction machine
PublicationThe article proposes a new method of reproducing the angular speed of the rotor of a cage induction machine designed for speed observers based on the adaptive method. In the proposed solution, the value of the angular speed of the rotor is not determined by the classical law of adaptation using the integrator only by an algebraic relationship. Theoretical considerations were confirmed by simulation and experimental tests.
-
The dynamic performance analysis of the Micro-turbine's rotor supparted on slide and roling element bearings
PublicationThis article presents the results of investigations of dynamic characteristics of a small-dimension rotor with slide and rolling element bearings. The object of investigations was the rotor-bearing system designed for the ORC based low-power steam micro-turbine. The investigations were performed using MESWIR series programs, as well as commercial FEA software ABAQUS and MADYN 2000. The results of modal analysis of the micro-rotor...
-
Sylwester Kaczmarek dr hab. inż.
PeopleSylwester Kaczmarek received his M.Sc in electronics engineering, Ph.D. and D.Sc. in switching and teletraffic science from the Gdansk University of Technology, Gdansk, Poland, in 1972, 1981 and 1994, respectively. His research interests include: IP QoS and GMPLS and SDN networks, switching, QoS routing, teletraffic, multimedia services and quality of services. Currently, his research is focused on developing and applicability...
-
RANS-based design optimization of dual-rotor wind turbines
PublicationPurpose An improvement in the energy efficiency of wind turbines can be achieved using dual rotors. Because of complex flow physics, the design of dual-rotor wind turbines (DRWTs) requires repetitive evaluations of computationally expensive partial differential equation (PDE) simulation models. Approaches for solving design optimization of DRWTs constrained by PDE simulations are investigated. The purpose of this study is to determine...
-
Anna Witkowska dr hab.
PeopleAnnaWitkowska holds an M.Sc. in mathematics and computer science from the University of Gdańsk, Poland in 2001. She received her Ph.D. degree from the Technical University of Warsaw in 2011, and the D.Sc. (habilitation) degree in automation, electronic and electrical engineering from the Technical University of Gdańsk, in 2020. Currently she is a professor of the Gdańsk University of Technology, Faculty of Electrical and Control...
-
FOOD CONTROL
Journals -
Optimum Control of Gyroscopic Systems
PublicationThe problem of optimum control of transverse rotor vibrations with gyroscopic interactions has been described and solved in the paper. An integral performance index has been defined for such system in order to minimize vibration level of a chosen rotor point. For this reason, an efficient way of finding the weight coefficients of integral performance index for multi-degrees-of-freedom system with gyroscopic interactions has been...
-
Modeling the impact of discretizing rotor angular position on computation of field-oriented current components in high speed electric drives
PublicationModern drives consist of alternating current electric motors, and the field-oriented control (FOC) of such motors enables fast, precise, and robust regulation of a drive's mechanical variables such as torque, speed, and position. The control algorithm, implemented in a microprocessor, requires feedback from motor currents, and the quality of this feedback is essential to a drive's control properties. Motor phase currents are sampled...
-
Variable-fidelity shape optimization of dual-rotor wind turbines
PublicationPurpose Dual-rotor wind turbines (DRWTs) are a novel type of wind turbines that can capture more power than their single-rotor counterparts. Because their surrounding flow fields are complex, evaluating a DRWT design requires accurate predictive simulations, which incur high computational costs. Currently, there does not exist a design optimization framework for DRWTs. Since the design optimization of DRWTs requires numerous model...
-
SESSILE DROPLET CONTACT ANGLE OF WATER-Al2O3, WATER-TiO2 AND WATER-Cu NANOFLUIDS
PublicationThe goal of the present work was the experimental determination of the contact angle of droplets of three nanofluids on various substrates. Of particular interest was effect of nanoparticle concentration on droplet contact angle.
-
Sensorless IPMSM drive with rotor position estimator based on analysis of phase current derivatives
PublicationThis paper describes a sensorless Interior Permanent Magnet Synchronous Motor (IPMSM) drive designed for traction applications. Wide-speed sensorless operation is provided with the use of three methods of rotor position estimation designed for: a standstill, low- and high-speed range. The paper focuses on the high-speed estimation algorithm. The estimator uses the derivatives of motor phase currentsresulting from PWM modulation...
-
Cooperative control in production and logistics
PublicationClassical applications of control engineering and information and communication technology (ICT) in production and logistics are often done in a rigid, centralized and hierarchical way. These inflexible approaches are typically not able to cope with the complexities of the manufacturing environment, such as the instabilities, uncertainties and abrupt changes caused by internal and external disturbances, or a large number and variety...
-
Sessile droplet contact angle of water–Al2O3, water–TiO2 and water–Cu nanofluids
PublicationThis work presents measurements of the contact angle of sessile droplets for three nanofluids, i.e. water–Al2O3, water–TiO2 and water–Cu. The plates made of glass, anodized aluminium and stainless steel of different roughness served as substrates. Ultrasonic vibration was used for 30–60 min in order to stabilise the dispersion of the nanoparticles. Nanoparticles were tested at the concentration of 0.01%, 0.1%, and 1% by weight....
-
Modeling the impact of rotor movement on non-linearity of motor currents waveforms in high-speed PMSM drives
PublicationMotor current measurement techniques as well as predictive control algorithms for electric drives rely on an assumption of linear motor currents changes resulting from constant inverter output voltages. Recent research has reported that this assumption does not hold in motors with short electrical time constant, and in drives whose rotor position advances substantially during a control period. This paper proposes a simulation model...
-
Improving Output Performance of the Ultrasonic Multicell Piezoelectric Motor by Development the Multi-Rotor Structure
PublicationIn recent years, many researches have been carried out on piezoelectric multi-rotor structures. This paper describes the analysis, development and experimental process of an ultrasonic multi-cell piezoelectric motor using a multi-rotor structure. In this design, three independent cells have been integrated into a mechatronic system. Analytical model and finite element method are used for modal and dynamic analysis of the proposed...
-
Chapter 2: Modelling and analysis of rotor with magnetic bearing system
PublicationThe paper is concerned with rotor magnetic bearing system modelling. Such system is a relatively complex electromechanical system and can be considered as typical mechatronic one. The port-based modelling of physical systems has been used to obtain discrete-continuous model of considered system. Proposed approach enables to obtain reduced low-order lumped parameter representation of the system including gyroscopic interactions....
-
Effect of the inclination angle of the condenser on the heat transfer coefficient value – experimental study
PublicationWhen considering problem of the condensation of the refrigerant in a flow inside channel, one needs to pay attention to the shape of its cross-section, the hydraulic diameter, the channel length as well as the orientation of the channel axis in space (horizontal, vertical, inclined). This paper presents an experimental study concerning the effect of the inclination angle of the condenser with a single coil pipe on the heat transfer...
-
Influence of concentration on contact angle of water-Cu nanofluid on glass substrate
PublicationIn the paper the results of an experimental investigation of influence of nanoparticle concentration on contact angle of water-Cu nanofluid on glass substrate have been presented. Nanoparticles were tested at the concentration of 0.01%, 0.1%, and 1% by weight. In the present study copper was applied as nanoparticle while distilled, deionized water was used as a base fluid. The mean diameter of nanoparticle is estimated to be 50...
-
Novel hierarchical nonlinear control algorithm to improve dissolved oxygen control in biological WWTP
PublicationWastewater treatment is a problem known to humankind for centuries. The quality of treated sewage determines the condition of reservoirs around the world. Control of such a complex and nonlinear system as a wastewater treatment plant requires thorough knowledge of the process. The paper presents a hierarchical control system of a Sequencing Batch Reactor (SBR) in Wastewater Treatment Plant (WWTP) taking into account a model based...
-
Automatics and control of technical processes 2023
e-Learning CoursesAutomatics and control of technical processes for Green Technologies 2023
-
Control of the wind turbine generator
PublicationWind power system consists of two main parts: wind turbine and electrical generator. Wind turbine converts the energy of the flowing air into mechanical energy, next generator converts this energy into electrical energy that is sent to the power system. These two processes should be realized with maximum efficiency and the following requirements for the control system can be formulated: opti-mal wind power conversion, compensation...
-
Sensorless Control of Polyphase Induction Machines
PublicationThe basics of transformations of polyphase systems into orthogonal systems are explained. Vector models of induction machines in orthogonal planes are analysed and multiscalar models for rotor flux and main flux together with stator current are presented. A speed observer based on an extended model of the induction machine for selected variables is applied in the control system for the induction machine. On the basis of the model...
-
Robustified estimators of radar elevation angle using a specular multipath model
PublicationWe consider the problem of estimating the elevation angle in the presence of multipath. The proposed method belongs to the class of maximum likelihood-like estimators and employs a modified specular reflection model that accounts for the uncertainty of the steering vector by assuming that they are subject to unknown deterministic perturbations with bounded norms. The analysis, performed using convex optimization methods, allows...
-
Robert Piotrowski dr hab. inż.
PeopleRobert Piotrowski jest absolwentem Wydziału Elektrotechniki i Automatyki (2001r., kierunek: Automatyka i Robotyka) oraz Wydziału Zarządzania i Ekonomii (2002r., kierunek: Organizacja Systemów Produkcyjnych) Politechniki Gdańskiej. Od 2005 roku jest zatrudniony na Wydziale Elektrotechniki i Automatyki, aktualnie w Katedrze Inteligentnych Systemów Sterowania i Wspomagania Decyzji. W 2005 roku obronił rozprawę doktorską (Automatyka...
-
Estimation of interior-permanent-magnet-synchronous-motor rotor position by analysis of phase-current derivatives
PublicationThis paper describes an algorithm for estimation of IPMSM rotor angular position. The algorithm uses derivatives of motor phase currents resulting from PWM modulation to obtain the rotor position. The presented method is designed for medium- and high-speed range, since it is based on determination of the EMF vector. Calculation of the motor position is performed in every PWM cycle. The standard SV-PWM method is used to determine...
-
UHF ESPAR antenna for simple Angle of Arrival estimation in UHF RFID applications
PublicationAn electronically switched beam antenna for localization of passive UHF RFID tags based on a simple Angle of Arrival (AoA) technique is proposed‥ Detailed antenna design and realization are presented together with corresponding simulations and measurement results. Experimental tests with passive UHF RFID tag show the validity of theoretical assumptions for application of the antenna in UHF RFID based localization systems.
-
Hierarchical predictive control of integrated wastewater treatment systems
PublicationThe paper proposes an approach to designing the control structure and algorithms for optimising control of integrated wastewater treatment plant-sewer systems (IWWTS) under a full range of disturbance inputs. The optimised control of IWWTS allows for significant cost savings, fulfilling the effluent discharge limits over a long period and maintaining the system in sustainable operation. Due to the specific features of a wastewater...
-
Mieczysław Brdyś prof. dr hab. inż.
People -
Digital Control
e-Learning CoursesII st (ang), sem. AiR
-
Impact of the inclination angle of the condenser with refrigerant R410A on heat transfer coefficient – experimental study
PublicationIn the paper the authors present results of a laboratory test of the condenser with refrigerant R410A. The effect of the inclination of this condenser on the heat transfer coefficient value has been considered. The test has proved that there is an optimal inclination angle of the condenser which gives maximal value of this coefficient.
-
Static and Dynamic Mechanical Properties of 3D Printed ABS as a Function of Raster Angle
PublicationDue to the rapid growth of 3D printing popularity, including fused deposition modeling (FDM), as one of the most common technologies, the proper understanding of the process and influence of its parameters on resulting products is crucial for its development. One of the most crucial parameters of FDM printing is the raster angle and mutual arrangement of the following filament layers. Presented research work aims to evaluate different...
-
Integrated monitoring, control and security of Critical Infrastructure Systems
PublicationModern societies have reached a point where everyday life relies heavily on desired operation of critical infrastructures, in spite of accidental failures and/or deliberate attacks. The issue of desired performance operation of CIS at high security level receives considerable attention worldwide. The pioneering generic methodologies and methods are presented in the paper project for designing systems capable of achieving these...
-
Sensorless Control of Induction Machine Supplied by Current Source Inverter
PublicationThe paper describes the voltage control technique of induction machines supplied by a current source inverter. The control system is based on proposed new multi-scalar variables, which are named “r.” The control system contains the output filter capacitor's model. In the sensorless control system the Z type backstepping speed observer was applied. The mathematical dependences are confirmed by simulation and experimental research.
-
Feedback Control of Multiphase Induction Machines with Backstepping Technique
PublicationThe paper presents the control possibility of five phase induction machines. In the proposed solution the machine model vector form is not transformed to the (dq)-coordinate system, that is connected to rotor flux vector, but utilizes the stationary system ( αβ ). Moreover, the nonlinear model linearization is based on demonstrated nonlinear variables transformation for i-orthogonal ( αβ )(n) planes. By introducing the backstepping...
-
Measurements of droplet contact angle of nanofluids
PublicationPrzedstawiono wyniki pomiarów kąta zwilżania trzech nanocieczy: woda-Al2O3, woda-TiO2 oraz woda-Cu. Koncentracja nanocząstek wynosiła: 0.01%, 0.1% oraz 1%. Pomiary przeprowadzono dla podłoża szklanego, aluminiowego i ze stali nierdzewnej. Kąt zwilżania mierzono za pomocą goniometru, a także na podstawie zdjęć wykonanych za pomocą kamery cyfrowej.
-
Axial-Flux Permanent-Magnet Dual-Rotor Generator for a Counter-Rotating Wind Turbine
PublicationCoaxial counter-rotating propellers have been widely applied in ships and helicopters for improving the propulsion efficiency and offsetting system reactive torques. Lately, the counter-rotating concept has been introduced into the wind turbine design. Distributed wind power generation systems often require a novel approach in generator design. In this paper, prototype development of axial-flux generator with a counter-rotating...
-
VSC converters control for offshore wind farms HVDC grid connection
PublicationThe paper proposes a voltage sourced converter (VSC) new control method. A well-known in the electric power systems correlation between voltage angle and active power and correlation between voltage and reactive power is used instead of feedforward control. This allows for a fast and almost independent control of active and reactive power flow.
-
Sensorless Field Oriented Control of Five Phase Induction Motor with Third Harmonic Injection
PublicationIn this paper, a sensorless field oriented control system of five-phase induction machine with the 3rd harmonic rotor flux is presented. Two vector models, α1-β1 and α3-β3, were transformed into d1-q1, d3-q3 models oriented in rotating frames, which correspond to the 1st and 3rd harmonic plane respectively. The authors proposed the linearization of the model in d-q coordinate frames by introducing a new variable “x” which is proportional...
-
Voltage Control of a Stand-Alone Multiphase Doubly Fed Induction Generator
PublicationThis article presents a multiphase doubly fed induction generator (MDFIG) with a dedicated and unique control algorithm in a stand-alone wind energy conversion system. The algorithm has been developed and elaborated in the case of different emergency modes. Compared with the traditional double-fed induction generator, the MDFIG has increased reliability, reduced current level per phase, and low rotor harmonic currents. The control...
-
Thermal failure of a second rotor stage in heavy duty gas turbine
PublicationThe impulse mode of operation and the supply of various types of fuels causes frequent failures even in the heavy duty gas turbines. The paper presents the ravages of second rotor stage failure in a gas turbine. The excessive thermal elongation rise caused by fuel change was indicated as the main cause. We applied nonlinear numerical analysis, preceded by thermodynamic calculations of the turbine and visual inspection of the effects...
-
Archives of Control Sciences
Journals