displaying 1000 best results Help
Search results for: POLLUTANTS IN ATMOSPHERIC AIR
-
Influence of drying mode and feed per tooth rate on the fine dust creation in pine and beech sawing on a mini sash gang saw
PublicationThe experimental results of the study focused on the effect of drying processes of modified air drying and warm air steam mixture drying of pine and beech wood on the size of sawdust particles created in cutting using PRW-15M sash gang saw, are presented in the paper. Particle size analysis of dry sawdust was performed using two methods—sieving method and laser diffraction analysis. The results showed that the drying process did...
-
Electrical and noise responses of graphene/AlGaN/GaN field-effect transistor for nitrogen dioxide, teatrahydrofuran, and acetone sensing
Open Research DataThis data set consists of raw and modified data concerning current-voltage characteristics and low-frequency noise spectra measured for graphene/AlGaN/GaN field-effect transistor in the ambiance of selected gases (laboratory air, dry and wet synthetic air, nitrogen dioxide, tetrahydrofuran, and acetone). The data show that sensor responses are enhanced...
-
Changes in heat of vanadium xerogel powder under different atmosphere
Open Research DataThe DataSet contains the DSC curves of the vanadium xerogel powder. The information about xerogel powder synthesis is described in the Journal of Nanomaterials.
-
The influence of drying parameters on wood properties
PublicationThe influence of drying conditions on wood properties is presented. The classical approach was used to determine energetic effects (cutting forces and cutting power) of wood sawing process on the basis of the wood specific cutting resistance, material constant. Before mashining wood material (soft and hard) was dryied at various conditions using air at 25oC, air-steam meaxture at 80oC and steam at 110oC.
-
Zaliczenia w terminach niestandardowych
e-Learning CoursesI stopień studiów EiT/IBM/AiR
-
Application of Nanomaterials for Cadmium Adsorption for Sustainable Treatment of Wastewater: a Review
PublicationMany heavy metals, particularly cadmium, are detrimental to both people and the environment when present in large quantities. In wastewater treatment plants, several conventional approaches are employed for cadmium abatement to restore the ecosystem, food supplies, and health of people and animals. Ion exchange, coagulation, membrane filtration, and chemical precipitation are a few examples of ways for removing heavy metals from...
-
The Influence of Weather Anomalies on Mercury Cycling in the Marine Coastal Zone of the Southern Baltic—Future Perspective
Publication -
Mercury in the Diatoms of Various Ecological Formations
Publication -
Mercury and Chlorinated Pesticides on the Highest Level of the Food Web as Exemplified by Herring from the Southern Baltic and African Penguins from the Zoo
Publication -
Mercury in marine fish, mammals, seabirds, and human hair in the coastal zone of the southern Baltic
Publication -
Decolorisation of Methylene Blue with Sodium Persulfate Activated with Visible Light in the Presence of Glucose and Sucrose
PublicationThe paper presents the results of research on the methylene blue (MB) degradation with sodium persulfate (PDS) activated with visible light (Vis) in the presence of glucose and sucrose. The following test were examined: absence and presence of sugars in concentrations of 50–300 mM, presence and absence of Vis radiation, pH of the model solution (6.0–12.0), identification of free radicals, kinetics of the pseudo-first-order reaction....
-
Comparison of Photocatalytic and Photosensitized Oxidation of Paraben Aqueous Solutions Under Sunlight
Publication -
Odour Samples Degradation During Detention in Tedlar® Bags
Publication -
Screening of Microorganisms for Biodegradation of Simazine Pollution (Obsolete Pesticide Azotop 50 WP)
Publication -
Toxicity Assessment by Microtox® in Sediments, Pore Waters and Sediment Saline Elutriates in the Gulf of Gdansk (Baltic Sea)
Publication -
The Impact of Dredging Deep Pits on Organic Matter Decomposition in Sediments
Publication -
Zinc Removal from the Aqueous Solutions by the Chemically Modified Biosorbents
Publication -
Stimulation of Heavy Metal Adsorption Process by Using a Strong Magnetic Field
Publication -
Remediation of Polycyclic Aromatic Hydrocarbons Contaminated Soil Using Combined Ozonation and Peroxy-Acid Treatment in the Site of Abadan Oil Refinery
Publication -
Investigating the Interaction Between Streptomyces sp. and Titania/Silica Nanospheres
Publication -
Adsorption Kinetics of Acid Dye Acid Red 88 onto Magnetic Multi‐Walled Carbon Nanotubes‐Fe3C Nanocomposite
Publication -
Visible Light–Driven Advanced Oxidation Processes to Remove Emerging Contaminants from Water and Wastewater: a Review
Publication -
Evaluation of specific capacity of poultry litter in heavy metal sorption
Publication -
Substance Flow Analysis of Mercury Affecting Water Quality in the European Union
PublicationW pracy zastosowano metodę SFA (Substance Flow Analysis) do oceny źródeł transportu i składowania rtęci w wodzie na terenie UE. W wyniku analizy stopnia zanieczyszczenia środowiska w przeszłości jak i scenariuszy zmian tego zanieczyszczenia w przyszłości stwierdzono, że spalanie paliw zawierających rtęć, takich jak węgiel i olej stanowi główne źródło zanieczyszczenia wody rtęcią.
-
Pesticides in precipitation from an urban region in Poland (Gdańsk-Sopot-Gdynia Tricity) between 1998 and 2000.
PublicationOznaczano wybrane pestycydy chloro-, azoto- i fosforoorganiczne w próbkach opadów zbieranych w 10 punktach w rejonie Gdańska w latach 1998-2000. Do najczęściej wykrywanych pestycydów należy zaliczyć symazynę, atrazynę, propazynę, fenitrotion, chlorofenwinfos, p,p`-DDT, o,p`-DDE, o,p`-DDD. Największe stężenia występowały w okresach aplikacji preparatów. Znaczący wpływ na stężenie pestycydów miała wielkość obszarów zielonych...
-
Interaction of Novel Ionic Liquids with Soils
PublicationWith the constant development of new ionic liquids, the understanding of the chemical fate of these compounds also needs to be updated. To this effect, in this contribution, the interaction of a number of novel ionic liquids with soils was determined. Therefore, three novel headgroups (ammonium, phosphonium or pyrrolidinium) with single or quaternary substitution were tested on a variety of soils with high to low organic matter...
-
Isolation and Characterization of Phenol-Degrading Psychrotolerant Yeasts
PublicationIn this study, the potential of selected psychrotolerant yeast strains for phenol biodegradation was studied. From 39 strains isolated from soil and water samples from Rucianka peat bog, three psychrotolerant yeast strains: A011, B021 and L012 showed the ability to phenol degradation. The result shows that all three yeast strains could degrade phenol at 500 mg l-1 and 750 mg l-1 concentration, whereas strains A011 and L012 could...
-
Numeryczna symulacja pracy gazowego kotła wodnego oraz ocena jego wpływu na środowisko
PublicationIlość dostarczanego powietrza oraz rozkład jego koncentracji w komorze paleniskowej mają istotny wpływ na prawidłowość przebiegu procesu spalania. Uzyskanie jednorodnego rozkładu jest praktycznie niemożliwe, dlatego powietrze dostarczane jest w nadmiarze. Konieczne jest jednak dobranie takiej wartości współczynnika nadmiaru powietrza, która pozwoli ograniczyć stratę wylotową, utrzymując przy tym wartości emisji na możliwie niskim...
-
"Numeryczna symulacja pracy gazowego kotła wodnego raz ocena jego wpływu na środowisko"
PublicationIlość dostarczanego powietrza oraz rozkład jego koncentracji w komorze paleniskowej mają istotny wpływ na prawidłowość przebiegu procesu spalania. Uzyskanie jednorodnego rozkładu jest praktycznie niemożliwe, dlatego powietrze dostarczane jest w nadmiarze. Konieczne jest jednak dobranie takiej wartości współczynnika nadmiaru powietrza, która pozwoli ograniczyć stratę wylotową, utrzymując przy tym wartości emisji na możliwie niskim...
-
"Numeryczna symulacja pracy gazowego kotła wodnego oraz ocena jego wpływu na środowisko"
PublicationIlość dostarczanego powietrza oraz rozkład jego koncentracji w komorze paleniskowej mają istotny wpływ na prawidłowość przebiegu procesu spalania. Uzyskanie jednorodnego rozkładu jest praktycznie niemożliwe, dlatego powietrze dostarczane jest w nadmiarze. Konieczne jest jednak dobranie takiej wartości współczynnika nadmiaru powietrza, która pozwoli ograniczyć stratę wylotową, utrzymując przy tym wartości emisji na możliwie niskim...
-
The effect of cable duct diameter on the ampacity of high-voltage power cables
PublicationThe ampacity of power cables depends, among others, on the conditions of heat dissipation from the cable to the environment. Cables are usually laid directly in the ground, but in some sections, they may be placed in ducts, which adversely affects the ampacity of the cable line. The paper presents heat transfer phenomena for cables installed in pipe-type ducts filled with air. The effect of cable duct diameter on this ampacity...
-
Modelowanie i identyfikacja [2020/21]
e-Learning CoursesStudia stacjonarne II st. AiR, semestr 1
-
Natural ventilation performance of family building in cold climate during windless time
PublicationIn this paper, the field measurements results are presented on the stack ventilation effect. The paper presents the results of performance (air change rate ACH) natural ventilation for building with inlet gap measured for the transitional season (between heating and summer season). The measurements were performed during a windless time. The house was located in northern Poland, in a cold climate region. The measurement system...
-
ASSESSMENT OF NATURAL VENTILATION SYSTEM FOR A TYPICAL RESIDENTIAL HOUSE IN POLAND
PublicationThe paper presents the research results of field measurements campaign of natural ventilation performance and effectiveness in a residential building. The building is located in the microclimate whose parameters differ significantly in relation to a representative weather station. The measurement system recorded climate parameters and the physical variables characterizing the air flow in the rooms within 14 days of the winter season....
-
Determination of flow properties of a pneumatic hose from changes in air pressure in a tank being emptied or filled by a differently configured pneumatic line
Open Research DataThe aim of the study was to determine the flow properties of various pneumatic hoses. The experiments were to measure the pressure changes in a being filled or emptied tank for a differently configured pneumatic line, including pneumatic hoses of different length and diameter. Three test configurations were used: (1) pressure source -> pneumatic...
-
Chip suction system in circular sawing machine: empirical research and computational fluid dynamics numerical simulations
PublicationThe experimental analysis of the wood chip removing system during its redesigning in the existing sliding table circular saw and computational fluid dynamic (CFD) numerical simulations of the air flow process is presented in the paper. The attention was focused on the extraction hood and the bottom shelter of the actual existing system. The main aim was to perform experimental research on the pressure distribution inside the...
-
Mitigation effect of face shield to reduce SARS-CoV-2 airborne transmission risk: Preliminary simulations based on computed tomography
PublicationWe aimed to develop a model to quantitatively assess the potential effectiveness of face shield (visor) in reducing airborne transmission risk of the novel coronavirus SARS-CoV-2 during the current COVID-19 pandemic using the computational fluid dynamics (CFD) method. The studies with and without face shield in both an infected and healthy person have been considered in indoor environment simulation. In addition to the influence...
-
Measured and predicted freeze-thaw days frequencies in climate change conditions in central Poland
PublicationThe rate of progression of geomorphological phenomena is greatly influenced by freeze-thaw processes. In the face of air temperature increasing over the past few decades, a question of the future impact of these processes arises, notably in the temperate and cold climate zones. Using the mean, maximum and minimum daily air temperature data in the period 1951–2018 obtained from three weather stations located in the vicinity of Jeziorsko...
-
Mitigation effect of face shield to reduce SARS-CoV-2 airborne transmission risk: Preliminary simulations based on computed tomography
PublicationWe aimed to develop a model to quantitatively assess the potential effectiveness of face shield (visor) in reducing airborne transmission risk of the novel coronavirus SARS-CoV-2 during the current COVID-19 pandemic using the computational fluid dynamics (CFD) method. The studies with and without face shield in both an infected and healthy person have been considered in indoor environment simulation. In addition to the influence...
-
High temperature corrosion and corrosion protection of porous Ni22Cr alloys
PublicationIn this work corrosion kinetics of the porous IN625 alloy is studied in the temperature range of 700 °C – 800 °C in air and humidified hydrogen for up to 1000 hours. Moreover, an effective and simple method of reducing corrosion rates of porous alloys by the infiltration of the rare earths elements is shown. Modification by the yttrium containing precursor reduces the corrosion rate by a factor of 50 in air at 700 °C so that the...
-
Measurement techniques for assessing the olfactory impact of municipal sewage treatment plants
PublicationThe study presents information about the measurement techniques used for the assessment of air quality in terms of the olfactory intensity resulting from the operation of municipal sewage treatment plants. Advantages and disadvantages of the measurement techniques used are presented. Sources of malodourous substance emission from sewage treatment plants were described, and the malodourous substances emitted were characterised....
-
Determination of selected chemical parameters in surface water samples collected from the Revelva catchment (Hornsund fjord, Svalbard)
PublicationSurface water samples (river and lake) were collected from the Revelva catchment every summer from 2010 to 2013. This study concerns importance of the use of some analytical techniques for pollutants and parameters deter- mination in Arctic environmental samples based on the example of total organic carbon, phenols, and formaldehyde determination and measurement of pH and electrical conductivity parameters. Significant...
-
30 years of treatment wetland application in poland- progress and reserch
PublicationThe experiences with design and operation of constructed wetlands in the Pommerania region during last 30 years followed by carried out investigations of treatment processes lead to the following conclusions:First applications of constructed wetlands for biological sewage treatment were made in 1984-92. The later implementations of multi-stage constructed wetlands in the individual household and local scale enable wastewater treatment...
-
The Specific Nature of Chemical Composition of Water from Volcanic Lakes Based on Bali Case Study
PublicationThe research area was localized in the Indonesian Archipelago, at the latitude of eight and nine degrees S on the one of the Lesser Sunda group island provinces, Bali (563,3 km2). Two massive calderas (Mount Batur 1717 m above sea level.; Mount Sangiyang 2093 m above sea level) are one of the most prominent landforms in the chain of volcanic mountain ranges of the Bali Island. Lake Batur (17,18 km2) and Batur Spring (which are...
-
Modelowanie i identyfikacja [st. niestacjonarne][2017/18]
e-Learning CoursesStudia IIgo stopnia, niestacjonarne, magisterskie, AiR sem. 1
-
Cyfrowe układy wbudowane i programowalne [2023/24]
e-Learning CoursesCyfrowe układy wbudowane i programowalne, AiR,
-
Modelowanie i podstawy identyfikacji [2020/21]
e-Learning CoursesStudia Igo stopnia, stacjonarne, inżynierskie, AiR sem. 5
-
Metrologia - Wykład ACiR/IBM
e-Learning CoursesWykład dla AiR/IBM sem. 2 st. inż.
-
New technologies using Trace Metals of Concern
PublicationThis chapter discusses the occurrence, material flows, technical applications of and pollution by platinum, palladium, thallium, rare earth elements, gold , silver, and antimony, all of which are essential for global economic growth. Modern technology relies on theses chemicals for the production of various industrial goods. however, their use releases pollutants into the environment, thus posing a threat to human health.
-
Underwater Local Cavity Welding of S460N Steel
PublicationIn this paper, a comparison of the mechanical properties of high-strength low-alloy S460Nsteel welded joints is presented. The welded joints were made by the gas metal arc welding (GMAW)process in the air environment and water, by the local cavity welding method. Welded joints were testedfollowing the EN ISO 15614-1:2017 standard. After welding, the non-destructive—visual, penetrant,radiographic, and ultrasonic (phased array) tests...