Search
displaying 1000 best results Help
Search results for: SHORT JUTE FIBRES
-
Preparation, morphology and properties of natural rubber composites filled with untreated short jute fibres
PublicationGreen composites were obtained by incorporation of short jute fibres in natural rubber matrix using a laboratory two-roll mill. The influence of untreated fibre content (1, 2.5, 5, 7.5 and 10 phr) on the mechanical properties, dynamic mechanical properties, swelling properties was examined. The behaviour of prepared green composites under cyclic compression was also investigated. Fibre dispersion in rubber matrix was studied by...
-
The impact of natural fibers’ characteristics on mechanical properties of the cement composites
PublicationThe paper reviews the properties of cement composites reinforced with short fibres. The effect of natural fibres was investigated: cotton, sisal, jute, ramie, bamboo, and synthetic fibres: polymer and polypropylene. It was noticed that the fibres change the consistency of the mixture up to 15%. In the composite flexural strength tests, a change in strength by +/− 8% was observed, depending on the type of fibres used. The research...
-
The miniaturised emission chamber system and home-made passive flux sampler studies of monoaromatic hydrocarbons emissions from selected commercially-available floor coverings
PublicationThe estimation of the emission rate of organic compounds released from various types of indoor materials can be performed using stationary environmental test chambers (ETC) classified as ex-situ methods or small-scale portable analytical devices based on the use of passive technique at the stage of analytes sampling from the gaseous phase (in-situ methods). The paper presents results of emissions of selected organic compounds from...
-
Impact response of novel layered two stage fibrous composite slabs with different support type
PublicationThe performance of novel Layered Two Stage Fibrous Composite slabs (LTSFC) was pioneered under falling mass collisions using a combined experimental and numerical study. Such LTSFC slabs consist of three layers with and without the insertion of glass fibre mesh between the layers. LTSFC techniques were used to fabricate the composite slabs with three layers including 3%, 1.5%, and 3% of fibre content for the top, middle, and...
-
Comparative Analysis of Carbon, Ecological, and Water Footprints of Polypropylene-Based Composites Filled with Cotton, Jute and Kenaf Fibers
PublicationComposites containing natural fibers are considered environmentally friendly materials which is related to the reduced use of fossil fuels and the emission of carbon dioxide compared to petroleum-based polymers. Nevertheless, a complete evaluation of their environmental impact requires a broader view. This paper presents a carbon, ecological, and water footprints assessment of polypropylene-based composites filled with cotton,...
-
Impact performance of novel multi-layered prepacked aggregate fibrous composites under compression and bending
PublicationMulti-layered Prepacked aggregate fibrous composite (MLPAFC) is a new type of concrete, which is prepared in two subsequent stages of aggregate-fibre skeleton prepacking and cementitious grouting. In this study, ten MLPAFC mixtures were prepared in three subsequent layers incorporating different contents of four different types of steel fibres. Long and short hooked-end and crimped steel fibers were adopted with 3.0 and 1.5% dosages...
-
Effect of polymer fibres reinforcement on selected properties of asphalt mixtures
PublicationThe paper presents selected results of the research program concerning fibre reinforced asphalt concrete. Aramid-polyalphaolefin fibres was used in this study. Selected properties responsible for low temperature cracking and resistance to permanent deformation are presented in this paper. Low temperature cracking susceptibility was evaluated with the results obtained from bending test of rectangular beams with constant rate of...
-
The effect of macro polymer fibres length and content on the fibre reinforced concrete
PublicationThe paper presents studies of a ready-mix concrete containing polymer fibres of three different lengths: 24, 38 and 54 mm. The performed tests allowed to determine the effect of fibre volume fraction and length on the concrete strength. The basic parameters of concrete mixture (consistency, air content and bulk density) were identified. Fibre reinforced concrete belongs to a group of composite materials. The polymer fibres are...
-
The Application of Fibres from Recycled Postconsumer Tyres for Concrete Reinforcement
PublicationPoland as a Member State is obliged to implement the EU specific environmental legislation focused on the reduction, transport and treatment of waste. The Landfill Directive prohibited the landfilling of whole tyres and their by-products. Although the EU Directive of Waste limits the use of tyres as secondary fuel, Poland is still the EU leader in burning tyres in cement kilns. Post-consumer tyres are utilised in a number of...
-
approximation of photonic crystal fibres with large air holes by the step index fibre model
PublicationAn equivalent step index fibre with a silica core and air cladding is used to model photonic crystal fibres with large air holes. We model this fibre for linear polarisation (we focus on the lowest few transverse modes of the electromagnetic field). The equivalent step index radius is obtained by equating the lowest two eigenvalues of the model to those calculated numerically for the photonic crystal fibres. The step index parameters...
-
Exotic Optical Fibres
Publication -
Special Optical Fibres
Publication -
FIBRES & TEXTILES IN EASTERN EUROPE
Journals -
Polyethylene glycol-coated solid-phase microextraction fibres for the extraction of polar analytes-A review
PublicationThe article discusses the merits and limitations of commercially available solid-phase microextraction (SPME) fibres and compares them with the new type of extraction coatings, in particular those containing polyethylene glycol as sorbent, as well as the methods of the preparation of the latter. It also analyses their possible application for the extraction of a broad spectrum of analytes, with particular emphasis on the sampling...
-
Multicore Optical Fibres For Sensors
Publication -
Special Fibres For Application Environments
Publication -
New matrix-free reference material for ethene in the form of optical fibres
PublicationReference materials are indispensable in the qualitycontrol and quality assurance of analytical measurements. Onenovel approach to the generation of standard gaseous mixturesof toxic, reactive, volatile, labile, and malodorous substancesinvolves thermal decomposition or rearrangement, under definedtemperature conditions, of compounds immobilized, bychemical bonding, on the surface of an appropriate carrier torelease specific amounts...
-
Studies in Short Fiction
Journals -
EJVES Short Reports
Journals -
Short Film Studies
Journals -
Nucleation and growth of CVD diamond on fused silica optical fibres with titanium dioxide interlayer
PublicationNucleation and growth processes of thin diamond films on fused silica optical fibres have been investigated. Fibres were coated with diamond film using microwave plasma enhanced chemical vapour deposition (µPE CVD) system. Since the growth of diamond on the fused silica glass requires high seeding density, two types of glass pre-treatment were applied: titanium dioxide (TiO2) interlayer deposition and sonication in nanodiamond...
-
Mechanical Performance and Environmental Assessment of Sustainable Concrete Reinforced with Recycled End-of-Life Tyre Fibres
PublicationThe presented research’s main objective was to develop the solution to the global problem of using steel waste obtained during rubber recovery during the tire recycling. A detailed comparative analysis of mechanical and physical features of the concrete composite with the addition of recycled steel fibres (RSF) in relation to the steel fibre concrete commonly used for industrial floors was conducted. A study was carried out using...
-
Application of short-time GNSS solution geodynamical studies
PublicationThe paper presents the results of research related to the application of GNSS solutions in short observational periods in geodynamical investigations. Authors used the 3-hour solution appointed from hour-long interval of about 30 chosen stations on mountainous terrains from over 100 which were worked out. The main aim was to check the correctness of such solutions by the comparison with the daily ones. Some outliers in East component...
-
Calculations of Short-Circuit Current Flows in Earth Wires of HV Lines
PublicationThis paper presents a method which enables calculating flows of short-circuit currents in earth wires of high voltage transmission lines, and its implementation in the form of a computer programme. The algorithm enables performing calculations for a double-fed line and starconnected lines (three terminal lines). The developed programme enables verifying dimensioning of earth wires in the context of their short-circuit thermal withstand...
-
TB11 test for short w-beam road barrier
PublicationFEM (Finite Element Method) is well-suited and widely used tool for simulating a range of phenomena: from these with simple and static behaviour, up to those complicated, highly nonlinear and involving many contacts. In present paper we use one of the advantages of FEM: parametric study could be easily performed and is more economical than series of in-situ tests. If recommended practices is carefully followed, results obtained...
-
Magnetic Field Generated by Short Circuit Current in the 110 kV Power System
PublicationElectric fields within tissues induced by magnetic fields including transients or short-term peaks should not be time averaged and be regarded as instantaneous values as established in the ICNIRP (International Commission on Non - Ionizing Radiation Protection) guidelines. Measurements of power lines magnetic fields with regard to human beings exposure are carried out typically with maximum current load at current balance condition...
-
Airborne wear particle emission from train brake friction materials with different contents of steel and copper fibres
PublicationThis study investigated the influence of the amount of steel and copper fibres in a train brake friction material on the tribological performance, emission intensity and characteristics of airborne wear particles. The particles were generated on a pin-on-disc tribometer under controlled friction and environmental conditions. It was found that the steel fibre results in a more intensive emission of 0.3–10 μm particles compared to...
-
Capillary Electrophoresis in determination of short - chain carboxylic acids in aqueous samples
PublicationAnalysis of pollution is extremely important especially in areas directly adjacent tothe residential district. Studies show that short- chain carboxylic acids are a group ofcompounds widespread around sewage treatment plants, landfills, livestock farms. The mostcommon techniques for determination of short - chain carboxylic acids are chromatographictechniques, especially gas chromatography, whose main limitation is that only volatilemonocarboxylic...
-
Effective Short -term Forecasting of Wind Farms Power
PublicationForecasting a specific wind farm's generation capacity within a 24 hour perpective requires both a reliable forecast of wind, as well as supporting tools. This tool is a dedicated model of wind farm power. This model should include not only general rules of wind to mechanical energy conversion, but also the farm's specific features. This paper present analytical, statistical, and neuron models of wind farm power. The study is based...
-
Submicron inorganic particles as an additional filler in hybrid epoxy matrix composites reinforced with glass fibres
PublicationIn this study, the effect of selected submicron metal oxide (zinc oxide, titanium oxide) or non-metal oxide (silicon dioxide) particles on mechanical and thermo-mechanical properties of epoxy/glass composites was investigated. The applied epoxy resin was a diglycidyl ether of bisphenol-A cured with triethylenetetramine. As a reinforcement twill weave E-glass fabric was used. Hybrid composites (contained particulate and fibrous...
-
Broadband Buses Based On Multicore Optical Fibres
Publication -
Multiclad Monomode Optical Fibres By MZD Technology
Publication -
Single-Mode Quadruple-Core Optical Fibres
Publication -
Application of optical fibres in oxidation-reduction titrations
Publication -
Short Fiction in Theory and Practice
Journals -
Using phase of short-term Fourier transform for evaluation of spectrogram performance
PublicationThe concept of spectrogram performance evaluation which exploits information on phase of short-term Fourier transform (STFT) is presented. A spectrograph which is time-frequency analyzing tool, is compared to a filter bank that demultiplexes a signal. Local group delay (LGD) and channelized instantaneous frequency (CIF) is obtained for each filtered component signal. In presented solution the performance is evaluated using so-called...
-
Determination of short-chain monocarboksylic acids in cattle farm and dairy industry wastewater
PublicationThe paper describes application of various techniques to determine short-chain monocarboksylic acids (SCMAs) in samples from the successive steps from milk production: from wastewater from cattle farm to wastewater from dairy industry. Each technique of sample preparation is followed by gas chromatographic analysis.
-
The influence of polypropylene fibres on the properties of fresh and hardened concrete
Publication -
The effect of the concentration of steel fibres on the properties of industrial floors
Publication -
Effectiveness of Concrete Reinforcement with Recycled Tyre Steel Fibres
Publication -
Recovery of Anammox Biomass at Short Hydraulic Retention Time in a MBR Reactor
PublicationThe anammox system has been consider as an economical option for treating high concentration of nitrogen and poor in biodegradable orgaednic carbon wastewaters. This process is attractive option compared with conventional nitrogen removal because it provides a significant saving in aeration and organic addition for denitrification. The anammox technology has been applied mostly for concentrated nitrogenous wastewater containing...
-
Effect of the let-through energy of overcurrent protective devices on the temperature of conductors during short-circuits
PublicationThe scope of the verification of low-voltage systems covers the earth fault loop impedance measurement. This measurement is usually performed with the use of low-value current meters, which force a current many times lower than the one occurring during a real short-circuit. Therefore, the international standard recommends consideration of the increase of resistance of conductors with the increase of temperature, which may occur...
-
INFLUENCE OF TEMPERATURE ON THE ACTIVITY OF ANAMMOX GRANULAR BIOMASS - SHORT AND LONG-TERM ASPECT
PublicationThe aim of this study was to determine a short-term and long-term effect of temperature on the anammox process rate and determination of temperature coefficients in the Arrhenius and Ratkowski equations. The short-term effects of temperature on the anammox biomass were investigated in batch tests at ten different temperatures in the range of 10-55 ̊C. The maximum rate 1.3 gN (gVSS·d)-1 observed at 40 ̊C. The minimum rate, close...
-
Short and Long Term Measurements in Assessment of FRP Composite Footbridge Behavior
PublicationThe paper presents application of different sensors for the purpose of short and long term measurements, as well as a structural health monitoring (SHM) system to assess the behavior of a novel fiber reinforced plastics (FRP) composite footbridge. The aim is to present a thorough and concise description of these sensors networks and results gathered with their aid during in situ measurement of strains, displacements, and vibrations,...
-
Short-Term Price Reaction to Filing for Bankruptcy and Restructuring Proceedings—The Case of Poland
PublicationThis study aims to check market reaction to filing for bankruptcy and restructuring proceedings and to verify the short-term effect of a price reversal in the Polish market in the years 2004–2019. The research was conducted by dividing the analysed companies according to the procedure (bankruptcy and restructuring) and market (the main market and the NewConnect market). The research methodology used in the study is the event analysis...
-
In vivo degradation of short-term implants
PublicationStan powierzchni wywiera istotny wpływ na właściwości użytkowe implantu. Stawiane wymagania, zależą od funkcji jakie ma spełniać wszczep oraz rodzaju implantowanego materiału. W przypadku implantów krótkotrwałych wymagana jest przede wszystkim odpowiednia odporność korozyjna, nie powinno tworzyć się trwałe połączenie pomiędzy wszczepem a tkanką kostną.Wszystkie biomateriały ulegają degradacji. Ważne jest to, aby produkty tej degradacji...
-
Soil improvement by short stone columns.
PublicationW artykule przedstawiono sposób dogęszczania podłoża gruntowego wykorzystywany do renowacji istniejących nawierzchni placów składowych i dróg. Proponowany sposób polega na formowaniu w gruncie kolumny o niewielkiej średnicy. Kolumnę tą formuje się poprzez wbijanie w rozluźnione podłoże trzpienia stalowego, z jednoczesnym dosypywaniem gruntu.Sposób ten stosuje się przede wszystkim jako metodę wzmocnienia podłoża pod nawierzchniami...
-
Dielectric strenght of the ultra - short fuse
PublicationW referacie omówiono współpracę ultraszybkiego bezpiecznika z bezstykowymhybrydowym ogranicznikiem prądów. Przeanalizowano wytrzymałość kanału połukowego bezpiecznika w zależności od długości topika oraz czasu działania tranzystora IGBT. Omówiono warunki i wyniki badań eksperymentalnych.
-
Event Infrastructure - Short-lived or Forever?
Publication -
Short-fuse arc in the magnetic field
PublicationDo wymuszenia przerzutu prądu z bezpiecznika krótkotopikowego o dużym prądzie znamionowym, lecz małej zdolności wyłączania do do innego - o małym prądzie znamionowym, lecz dużej zdolności wyłączania konieczne jest wytworzenie przez bezpiecznik krótkotopikowy wysokiego napięcia łukowego. Do tego celu bezpiecznik z topikiem o długości 1 mm wyposażono w rożki łukowe i płykową komorę dejonizacyjną oraz zastosowano zewnętrzne pole...