Search
Search results for: evaporation
-
Evaporation and condensation
PublicationW pracy przedstawiono encyklopedyczne ujęcie wrzenia i kondensacji.
-
ENHANCED EVAPORATION OF THE DROPLETS OF CONDENSATE IN THE ASYMMETRICAL SHOCK WAVE ZONE
PublicationIn the low-pressure part of steam turbine, the state path usually crosses the saturation line in penultimate stages [4,5]. The formation and evolution of these droplets lower the performance of the wet stages of the turbines, and their effects on the efficiency are collectively known as wetness losses [4]. Nowadays, due to work of steam turbines at partial load, process of homogeneous and heterogeneous condensation still is current....
-
An advanced thermal-FSI approach of an evaporation of air heat pump
PublicationThe paper presents selected problems of numerical modeling of an advanced thermal-FSI approach of evaporator of air heat pomp. The example of a fin-tube evaporator has been studied, focusing on obtaining of heat exchanger characteristics applying two-phase flow model for the in-tube refrigerant flow. Special attention is given to heat transfer between separated medium for different air velocity and changed refrigerant mass flow...
-
Metal Oxides and Low Temperature SWCNT Synthesis via Laser Evaporation
Publication -
Osmotic membrane distillation with continuous regeneration of stripping solution by natural evaporation
Publication -
Comparison of Ozonation and Evaporation as Treatment Methods of Recycled Water for Bioethanol Fermentation Process
PublicationThe paper compared the performance of the ethanol yield after alcoholic fermentation with samples of rejected (RW) and permeate water (PW), RW and PW treated by oxidation with ozone (O3) (5 and 15 min) and evaporation, aiming the recirculation back to the bioethanol process. RW and PW were collected after an anaerobic bioreactor (AnBR) used for stillage treatment. Nine types of fermentations were made, where one used 100% tap...
-
Organic semiconductor rubrene thin films deposited by pulsed laser evaporation of solidified solutions
PublicationOrganic semiconductor rubrene (C42H28) belongs to most preferred spintronic materials because of the high charge carrier mobility up to 40 cm2(V·s)-1. However, the fabrication of a defect-free, polycrystalline rubrene for spintronic applications represents a difficult task. We report preparation and properties of rubrene thin films deposited by pulsed laser evaporation of solidified solutions. Samples of rubrene dissolved in aromatic...
-
On the origin of surface imposed anisotropic growth of salicylic and acetylsalicylic acids crystals during droplet evaporation
PublicationIn this paper droplet evaporative crystallization of salicylic acid (SA) and acetylsalicylic acid (ASA) crystals on different surfaces, such as glass, polyvinyl alcohol (PVA), and paraffin was studied. The obtained crystals were analyzed using powder X-ray diffraction (PXRD) technique. In order to better understand the effect of the surface on evaporative crystallization, crystals deposited on glass were scraped off. Moreover,...
-
On the origin of surfaces-dependent growth of benzoic acid crystal inferred through the droplet evaporation method
PublicationCrystal growth behavior of benzoic acid crystals on different surfaces was examined. The performed experiments documented the existence of very strong influence introduced by polar surfaces as glass, gelatin, and polyvinyl alcohol (PVA) on the growth of benzoic acid crystals. These surfaces impose strong orientation effect resulting in a dramatic reduction of number of faces seen with x-ray powder diffractions (XPRD). However,...
-
On the origin of surfaces-dependent growth of benzoic acid crystal inferred through the droplet evaporation method
PublicationCrystal growth behavior of benzoic acid crystals on different surfaces was examined. The performed experiments documented the existence of very strong influence introduced by polar surfaces as glass, gelatin, and polyvinyl alcohol (PVA) on the growth of benzoic acid crystals. These surfaces impose strong orientation effect resulting in a dramatic reduction of number of faces seen with x-ray powder diffractions (XPRD). However,...
-
On the origin of surfaces-dependent growth of benzoic acid crystal inferred through the droplet evaporation method
PublicationCrystal growth behavior of benzoic acid crystals on different surfaces was examined. The performed experiments documented the existence of very strong influence introduced by polar surfaces as glass, gelatin, and polyvinyl alcohol (PVA) on the growth of benzoic acid crystals. These surfaces impose strong orientation effect resulting in a dramatic reduction of number of faces seen with x-ray powder diffractions (XPRD). However,...
-
Numerical model for thin liquid film with evaporation and condensation on solid surfaces in systems with conjugated heat transfer
PublicationCondensation and evaporation processes from wetted surfaces are of utmost importance in many technological or industrial applications. In many devices such as home-appliances and air conditioning systems just to name a few, condensation and evaporation processes greatly impact their performance and energy efficiency; The physics of these processes is quite complex, involving conjugate heat transfer among solid–liquid film-gaseous...
-
Changes in evaporation patterns and their impact on Climatic Water Balance and river discharges in central Poland, 1961–2020
PublicationThis study investigates the changes in precipitation and evaporation patterns and their impact on Climatic Water Balance and river discharges in central Poland from 1961 to 2020. The analysis focuses on two “normal” periods, 1961–1990 and 1991–2020 (according to the World Meteorological Organization). Bartlett’s test and the Kruskal–Wallis rank sum test were used to assess the homogeneity of variances and compare distributions...
-
Rubrene Thin Films with Viably Enhanced Charge Transport Fabricated by Cryo-Matrix-Assisted Laser Evaporation
PublicationAmong organic semiconductors, rubrene (RB; C42H28) is of rapidly growing interest for the development of organic and hybrid electronics due to exceptionally long spin diffusion length and carrier mobility up to 20 cm2V−1s−1 in single crystals. However, the fabrication of RB thin films resembling properties of the bulk remains challenging, mainly because of the RB molecule’s twisted conformation. This hinders the formation of orthorhombic...
-
A Systematic and Comparative Study of Binary Metal Catalysts for Carbon Nanotube Fabrication Using CVD and Laser Evaporation
Publication -
SAXS examination of the water evaporation process from silica materials coated with a polysaccharide–polyimine copolymer layer
Publication -
Functional phase bistability in a nanocrystalline RbMn[Fe(CN)6] thin film fabricated by matrix-assisted laser evaporation
PublicationOne of the main barriers hindering applications of Prussian blue metal assemblies is their poor processability, which makes the fabrication of intact thin films very difficult. In this work, a nanocrystalline RbMn[Fe(CN)6]·xH2O film on silicon substrate was obtained for the first time via laser-stimulated deposition and investigated. Temperature-induced phase transition and bistability within broad hysteresis loop (120 K), along...
-
Nanocrystalline Polymer Impregnated [Fe(pz)Pt(CN)4] Thin Films Prepared by Matrix-Assisted Pulsed Laser Evaporation
PublicationIn this work, the fabrication of [Fe(pz)Pt(CN)4] (pz = pyrazine) thin films by means of matrix-assisted pulsed laser evaporation (MAPLE) was investigated. As starting material, a cryogenically cooled suspension of anocrystalline [Fe(pz)Pt- (CN)4] (0.35wt.-%) in a mixture of 1,1-dichloroethane and polyethylene glycol (PEG) was used. Films of a thickness up to 150–200 nm were deposited on Si substrates by laser ablation at λ = 1064...
-
The ability of children aged 6 and 9 years, respectively, to detect errors in a narrative based on incorrect information about evaporation in the water cycle
Publication -
Preparation of Hydrogen Electrodes of Solid Oxide Cells by Infiltration: Effects of the Preparation Procedure on the Resulting Microstructure
PublicationIn this work, the infiltration technique was used to produce hydrogen electrodes for solid oxide cells. Different infiltration methodologies were tested in order to try to shorten the infiltration cycle time. The porous scaffolds used for infiltration were based on highly porous yttria-stabilized zirconia (YSZ) obtained by etching the reduced nickel from the Ni-YSZ cermet in HNO3 acid. The support had a complex structure which...
-
Possibilities of Increasing the Overall Efficiency of Gas-steam CHP Microplant
PublicationThe paper presents ways to increase the efficiency of a gas-steam micro power plant by modifying the cycle combination. The modification consists in partial release of the fluid downstream of the gas turbine and using it for ORC fluid overheating and evaporation. Advantages of this solution over the simplest gas and steam cycles’ combination are demonstrated.
-
Dariusz Mikielewicz prof. dr hab. inż.
PeopleProfessor Dariusz Mikielewicz – born on February 6, 1967. in Gdansk. Here in 1974 he enrolled first to the Elementary School No. 17, and then in the Grammar School No. 5, named after Stefan Żeromski in Gdansk-Oliwa. After graduating from the Secondary School, with honors, in 1985 he successfully passed the entrance exams to the Faculty of Mechanical Engineering of Technical University of Gdansk, where he graduated with a very good...
-
Self-assembled concentric stripes of diamond particles by a pinning-depinning mechanism
PublicationWe describe the novel mechanism of spontaneous formation of the concentric stripe patterns of microdiamonds via gradual solvent evaporation from a suspension confined in a teardrop well. The self-organized patterns exhibit a series of arcs with regular spacings varying between hundreds of micrometers and millimeters. They result from an interplay between the directional forced circulation of the solvent and a stick-slip movement...
-
Pre-oxidation of porous ferritic Fe22Cr alloys for lifespan extension at high-temperature
PublicationPre-oxidation of porous ferritic Fe22Cr alloys was extensively studied in this paper. Weight gain measurements and SEM analysis revealed that pre-oxidation performed at 900◦C for 40 min increased the lifespan of the alloy. A Cr evaporation study did not disclose any significant influence of the pre-oxidation process on the Cr content in the alloy. For a more detailed assessment, TEM imaging and X-ray tomography measurements of...
-
Synthesis, structural characterization, and thermal properties of Ca‐ and La‐doped soda‐lime glasses by laser melting
PublicationLaser melting techniques have been used in the preparation of unconventional glass compositions with high melting temperatures. Thus, we wanted to test the feasibility of using a CO2 laser in the preparation of nitrogen-rich oxynitride glasses and nitride silicate glasses. Melting from oxides and metallic raw materials, we wanted to study first glass formation and possible evaporation losses of the glass components. Two glass series...
-
NEW ORGANIC MATERIALS FOR PHOTOVOLTAICS
PublicationThis report presents the results of investigations carried out for polymer- and low-weightmolecular materials prepared in the form of thin films by various methods, namely the thermalvacuum evaporation and chemical vapour deposition. The influence of the technologicalconditions on the structure, surface morphology, and electronic properties of selected organic thinfilms, including polyazomethines, phthalocyanines, and perylene...
-
Effects of La Content on the Densification, Microstructure, and Conductivity of Doped La10−x Ge6 O26±δ Electrolytes
PublicationIn this study, the influence of La content on the characteristics of Nb-, Mo-, and W-doped LaxGe6O26±δ electrolytes was investigated through sintering study, X-ray diffraction, scanning electron microscopy, and conductivity measurement. The densification of LaxGe5.5Nb0.5O26±δ and LaxGe5.5W0.5O26±δ was retarded as the x reached 9.75, while that of LaxGe5.5Mo0.5O26±δ improved with increasing La content. The average grain size slightly...
-
SAFE - technika izolacji związków zapachowych z próbek żywności
PublicationOznaczanie składników odpowiedzialnych za zapach produktów żywnościowych dokonywane za pomocą technik chromatograficznych obejmuje dwa zasadnicze etapy: przygotowanie próbki i identyfikację (rozdzielenie połączone z odpowiednią metodą detekcji). Ze względu na skomplikowaną matrycę, specyfikę związków zapachowych - samoistne ich uwalnianie z matrycy, jak i możliwość zachodzenia przemian, kluczowym elementem analizy żywności jest...
-
Interplay of hydrogen bonding and aryl-perfluoroaryl interactions in construction of supramolecular aggregates
PublicationThe stacking between aryl and perfluoroaryl units is an important class of the aromatic – aromatic interactions that has attracted rapidly growing interest in recent years. Continuing interest of our group in this subject it had been prepared three new complexes of pentafluorobenzoic acid with benzyl alcohol, 4-methylbenzyl alcohol and 4-tert-butylbenzyl alcohol and in the next step investigated their self-assembly modes by...
-
Alternative cogeneration thermodynamic cycles for domestic ORC
PublicationThe Organic Flash Cycle (OFC) is suggested as a vapor power cycle that could potentially improve the efficiency of utilization of the heat source. Low and medium temperature finite thermal sources are considered in the cycle. Additionally the OFC’s aim is to reduce temperature difference during heat addition. The study examines 2 different fluids. Comparisons are drawn between the OFC and an optimized basic Organic Rankine Cycle...
-
Water Resources Management - Winter Semester 2021-2022
e-Learning CoursesWater Resources Management as defined for purpose of this course includes both water use and water excess management. The fundamental water resources engineering processes are the hydrologic processes and the hydraulic processes. The common threads that relate to the explanation of these processes are the fundamentals of fluid mechanics. The hydrologic processes include rainfall, evaporation, infiltration, rainfall-runoff and routing,...
-
WATER RESOURCES MANAGEMENT 2024
e-Learning CoursesWater Resources Management as defined for purpose of this course includes both water use and water excess management. The fundamental water resources engineering processes are the hydrologic processes and the hydraulic processes. The common threads that relate to the explanation of these processes are the fundamentals of fluid mechanics. The hydrologic processes include rainfall, evaporation, infiltration, rainfall-runoff and routing,...
-
A study of a reduction of a micro- and nanometric bismuth oxide in hydrogen atmosphere
PublicationA reduction of bismuth oxide in hydrogen atmosphere was investigated. The reaction was performed with a material in various structural forms: powder: with micrometric grains, powder with nanometric grains and powder pressed into pellets. The process was performed in both isothermal and non-isothermal conditions. An activation energy of the reaction calculated with Friedman method was found to be about 85 kJ/mol for the reduction...
-
Water Resources Management 2022/2023
e-Learning CoursesWater Resources Management as defined for purpose of this course includes both water use and water excess management. The fundamental water resources engineering processes are the hydrologic processes and the hydraulic processes. The common threads that relate to the explanation of these processes are the fundamentals of fluid mechanics. The hydrologic processes include rainfall, evaporation, infiltration, rainfall-runoff and routing,...
-
Determination of dryout localization using a five-equation model of annular flow for boiling in minichannels
PublicationDetailed studies have suggested that the critical heat flux in the form of dryout in minichannels occurs when the combined effects of entrainment, deposition, and evaporation of the film make the film flow rate go gradually and smoothly to zero. Most approaches so far used the mass balance equation for the liquid film with appropriate formulations for the rate of deposition and entrainment respectively. It must be acknowledged...
-
Ceramic composites for single-layer fuel cells
PublicationComposite materials consisting of acceptor doped lanthanum orthoniobate electrolyte phase (La0.98Ca0.02NbO4) and Li2O:NiO:ZnO semiconducting phase were synthesized. The precursor powder of La0.98Ca0.02NbO4 was prepared in nanocrystalline (mechanosynthesis) and microcrystalline (solid-state synthesis) form. The composite can be applied in a single-layer fuel cell, because of the presence of two phases acting as an anode and a cathode...
-
Novel Cold Crucible Ultrasonic Atomization Powder Production Method for 3D Printing
Publication: A new powder production method has been developed to speed up the search for novel alloys for additive manufacturing. The technique involves an ultrasonically agitated cold crucible installed at the top of a 20 kHz ultrasonic sonotrode. The material is melted with an electric arc and undergoes pulverization with standing wave vibrations. Several different alloys in various forms, including noble and metallic glass alloys, were...
-
EXAMINATION OF SOL-GEL DERIVED HYDROXYAPATITE ENHANCED WITH SILVER NANOPARTICLES USING OCT AND RAMAN SPECTROSCOPY
PublicationHydroxyapatite (HAp) has been attracting widespread interest in medical applications. In a form of coating, it enables to create a durable bond between an implant and surrounding bone tissues. With addition of silver nanoparticles HAp should also provide antibacterial activity. The aim of this research was to evaluate the composition of hydroxyapatite with silver nanoparticles in a non-destructive and non-contact way. For control measurements...
-
Prediction of coking dynamics for wet coal charge
PublicationA one-dimensional transient mathematical model describing thermal and flow phenomena during coal coking in an oven chamber was studied in the paper. It also accounts for heat conduction in the ceramic oven wall when assuming a constant temperature at the heating channel side. The model was solved numerically using partly implicit methods for gas flow and heat transfer problems. The histories of temperature, gas evolution and internal...
-
Influence of Gd deposition on the oxidation behavior and electrical properties of a layered system consisting of Crofer 22 APU and MnCo2O4 spinel
PublicationIn the study, the surface of the Crofer 22APU ferritic steel was modified with gadolinium oxide nanoparticles and a protective-conducting layer consisting of the MnCo2O4 spinel. This system was studied in the context of application in IT-SOFC interconnects. Four types of samples were studied: unmodified steel, steel coated with a manganese-cobalt spinel layer, steel modified with gadolinium oxide nanoparticles, and a system consisting...
-
Mn-Co spinel coatings on Crofer 22 APU by electrophoretic deposition: Up scaling, performance in SOFC stack at 850 °C and compositional modifications
PublicationCeramic coatings for metallic interconnects play a key role in limiting corrosion and chromium evaporation in solid oxide cells. This study presents the upscaling of the electrophoretic deposition (EPD) technique to process Mn-Co spinels on real-dimension Crofer 22 APU interconnects and the test in a SOFC stack. Area specific resistance of long-term test conducted for 5000 h at 850 °C demonstrated that two-steps sintering has a...
-
Comment on "Measurements without probabilities in the final state proposal"
PublicationThe final state proposal [G.T. Horowitz and J.M. Maldacena, J. High Energy Phys.2004(2),8 (2004)] is an attempt to relax the apparent tension betweenstring theory and semiclassicalarguments regarding the unitarity of black hole evaporation. The authors of [R. Bousso and D.Stanford, Phys. Rev. D89, 044038 (2014)] analyze thought experiments where an infalling observerfirst verifies the entanglement between early and late Hawking...
-
EFFECT OF NANOFLUID CONCENTRATION ON TWO-PHASE THERMOSYPHON HEAT EXCHANGER PERFORMANCE
PublicationAn approach – relaying on application of nanofluid as a working fluid, to improve performance of the two-phase thermosyphon heat exchanger (TPTHEx) has been proposed. The prototype heat exchanger consists of two horizontal cylindrical vessels connected by two risers and a downcomer. Tube bundles placed in the lower and upper cylinders work as an evaporator and a condenser, respectively. Distilled water and nanofluid water-Al2O3...
-
A simplified energy dissipation based model of heat transfer for subcooled flow boiling
PublicationIn the paper a model is presented based on energetic considerations for subcooled flow boiling heat transfer. The model is the extension of authors own model developed earlier for saturated flow boiling and condensation. In the former version of the model we used the heat transfer coefficient for the liquid single-phase as a reference level, due to the lack of the appropriate model for heat transfer coefficient for the subcooled...
-
Experimental validation of pressure drop models during flow boiling of R134a – effect of flow acceleration and entrainment
PublicationA crucial step to assure proficient work of power and process apparatus is their proper design. A wide array of those devices operates within boiling or condensation of the working fluid to benefit from high heat transfer rates. Two-phase flows are associated with high heat transfer coefficients because of the latent heat of evaporation and high turbulence level between the liquid and the solid surface. Predicting heat transfer...
-
Experimental review of the performances of protective coatings for interconnects in solid oxide fuel cells
PublicationFerritic stainless steel interconnects are used in solid oxide fuel cells; however, coatings are required to improve their performance. Although several types of coatings have been proposed, they have been scarcely investigated under similar conditions. This study compares the characteristics of uncoated Crofer 22 APU and eight different coatings on Crofer 22 APU for up to 3000 h at 800 ◦C. The coatings were deposited at various...
-
Effect of interconnect coating procedure on solid oxide fuel cell performance
PublicationChromium (Cr) species vaporizing from chromia-forming alloy interconnects is known as a source of degradation in solid oxide fuel cell (SOFC) stacks called “cathode poisoning”. (Mn,Co)3O4 spinel coatings offer good protection against Cr evaporation during operation. In this study, Crofer 22 APU steel interconnects were electrophoretically deposited in different mediums to obtain high packing of green coating layer. The optimized...
-
Investigation and operation problems of metal tanks in Poland
PublicationThe paper consists of three parts concerned with steel cylindrical, vertical tank for liquid fuel. In the first part the present trends in tank design and building in Poland are described. The main are: · reduction of environment contamination danger caused by tank leakage and hydrocarbons evaporation, · increasing capacity of new tanks (100000 m3 and more) due to economic factor - reduction of steel amount per m3 of storage capacity....
-
In-situ Cu-doped MnCo-spinel coatings for solid oxide cell interconnects processed by electrophoretic deposition
PublicationThe Cu doping of the Mn–Co spinel is obtained “in-situ” by electrophoretic co-deposition of CuO and Mn1.5Co1.5O4 powders and subsequent two-step reactive sintering. Cu-doped Mn1.5Co1.5O4 coatings on Crofer22APU processed by electrophoretic co-deposition method are tested in terms of long term oxidation resistance and area specific resistance tests up to 3600 h. The introduction of Cu in the spinel lead to higher level of densification...
-
The influence of the fuel spray nozzle geometry on the exhaust gas composition from the marine 4-stroke diesel engine
PublicationThe paper presents experimental research on a 4-stroke, 3-cylinder, turbocharged AL25/30 Diesel engine. Research consisted in investigating the effect of the geometry of the fuel injectors on the exhaust gas composition from the engine. During measurements, the engine was operated with a regulator characteristic of a load range from 40 kW to 280 kW, made by electric water resistance. The engine was mechanically coupled to the electric...