Filters
total: 926
filtered: 828
Search results for: cuttings
-
Evaluation of the Cathodic Electrodeposition Effectiveness of the Hydroxyapatite Layer Used in Surface Modification of Ti6Al4V-Based Biomaterials
PublicationThe important issue associated with the design and the fabrication of the titanium and titanium alloy implants is the increase of their biointegration with bone tissue. In the presented paper, the research results concerning the conditions used in the cathodic deposition of hydroxyapatite on the surface Ti6Al4V substrates primarily modified by the production of TiO2 nanoporous coatings, TiO2 nanofibers, and titanate coatings, are...
-
Influence of yttria surface modification on high temperature corrosion of porous Ni22Cr alloy
PublicationProtective coatings for porous alloys for high temperature use are relatively new materials. Their main drawback is high temperature corrosion. In this work protective coatings based the on Y-precursor infiltrated into the sintered Ni22Cr alloys are studied at 700°C. Effects of the amount of the protective phase on the resulting corrosion properties are evaluated in air and humidified hydrogen. Weight gain of the samples, their...
-
Wpływ zawartości grafitu na właściwości mechaniczne warstw hybrydowych Ni-P/Si3N4/grafit osadzonych na stopie AW-7075 metodą redukcji chemicznej.
PublicationPrzedstawiono wpływ obecności grafitu jako fazy dyspersyjnej na właściwości mechaniczne warstw hybrydowych Ni-P/Si3N4/grafit, które osadzono metodą redukcji chemicznej na stopie glinu AW-7075. Wykonano badania morfologii powierzchni warstw metodą mikroskopii świetlnej i skaningowej. Dalszą część pracy stanowiły badania mechaniczne, czyli pomiary mikrotwardości warstw oraz ich adhezji do aluminiowego podłoża, a także analizy wpływu...
-
Carboxy derivative of dioxydiphenylpropane diglycydyl ether monomethacrylate as an addtive for composites
PublicationThe modifier of composites was used in the presence of polyetylene polyamine. Physico-mechanical properties and chemical stability of coatings thus obtained were analyzed.
-
Comprehensive Evaluation of the Biological Properties of Surface-Modified Titanium Alloy Implants
PublicationAn increasing interest in the fabrication of implants made of titanium and its alloys results from their capacity to be integrated into the bone system. This integration is facilitated by different modifications of the implant surface. Here, we assessed the bioactivity of amorphous titania nanoporous and nanotubular coatings (TNTs), produced by electrochemical oxidation of Ti6Al4V orthopedic implants’ surface. The chemical composition...
-
Recovering Evaluation of Narrow-Kerf Teeth of Mini Sash Gang Saws
PublicationSash gang saws with narrow-kerf saw blades are used in the production of glued laminate flooring elements in plants where dry technology is applied. This means that boards or friezes are sawn into top layer lamellae in dry conditions (moisture content of about 10–12%) from expensive wood species, often exotic. The object of this research was stellite-tipped teeth of narrow kerf saw blades sharpened under industrial conditions....
-
Slurry Surfacing Mixes on the Basis of Bitumen Modified with Phenol-Cresol-Formaldehyde Resin
PublicationSlow-breaking monophase cationic bitumen emulsions have been produced on the basis of bitumen modified with phenol-cresol-formaldehyde resin (PhCR-F). Bitumen emulsions were used as a binder for thin-layer coatings with slurry surfacing mixes (SSM). Physical and technical parameters of modified and unmodified emulsions were determined and analyzed. The optimal compositions of SSM were selected according to the breaking criterion....
-
Methods of solving the Atkins equation determine shear angle with taking into consideration a modern fracture mechanics
PublicationIn the paper are presented methods of solving nonlinear Atkins equation . The Atkins equation describe shear angle with taking into account properties of material cutting. To solve Atkins equation has been used iterative methods: Newton method and simplified method of simple iteration. Method of simple iteration is presented in the form of Java application.
-
MOŻLIWOŚCI IDENTYFIKACJI STANU TECHNICZNEGO WARSTW ŚLIZGOWYCH ŁOżYSK SILNIKÓW SPALINOWYCH O ZAPŁONIE SAMOCZYNNYM W PRZYPADKU WYKORZYSTANIA EMISji AKUSTYCZNEJ JAKO SYGNAŁU DIAGNOSTYCZNEGO
PublicationW artykule zaprezentowano wyniki badań wielowarstwowych panwi łożysk ślizgowych silników tłokowych. Scharakteryzowano własności obciążeń tego rodzaju panwi oraz ich zużycia szczególnie zmęczeniowego i ściernego. Wykazano przydatność emisji akustycznej jako sygnału diagnostycznego do ujawniania zużycia powłok ślizgowych i zaporowych. Przedstawiono wyniki pomiarów parametrów emisji akustycznej, wykonanych za pomocą 12- kanałowej...
-
Studies on applicability of new solid-phase microextraction fibers for the selective extraction and determination of short - chain monocarboksylic acids
PublicationShort-chain monocarobxylic acids, sometimes referred to as volatile fatty acids (VFA), are a group of low molecular weight alkyl monocarboxylic acids that are widely distributed within the environment. These molecules contain any from 2 to 8 carbon atoms and originate from the anaerobic biodegradation of organic matter such as carbohydrates, proteins, and fats. These compounds are commonly found in the effluents from animal farming,...
-
Radionuclides activity and effective doses referred to geological formations
PublicationNaturally occurring radioactive materials (NORM) are present in Earth’s crust and they caused natural background radiation, variable in different regions. Liquid, gas and solid radionuclides emit three types of radiation – alpha, beta and gamma. Fluctuations of natural radioactivity in different geological formations in the world and in Poland were compared in relation to radiological hazard. Also drilling cuttings from boreholes...
-
Assesment of (Mn,Co)3O4powders for possible coating material for SOFC/SOEC interconnects
PublicationIn this work (Mn,Co)3O4 spinel powders with different Mn:Co ratio (1:1 and 1:2) and from different commercial suppliers are evaluated for possible powder for production of interconnect coatings. Sinterability of the powders is evaluated on pressed pellets sintered in oxidizing and in reducing/oxidizing atmospheres. For selected powder, coatings are then prepared by the electrophoretic deposition method on Crofer 22 APU stainless...
-
Evaluation of adhesion strength, corrosion, and biological properties of the MWCNT/TiO2 coating intended for medical applications
PublicationMulti-wall carbon nanotube (MWCNT) coatings are gaining increasing interest because of their special properties used in many science fields. The titania coatings are known for their improvement of osteoblast adhesion, thus changing the surface architecture. Bi-layer coatings comprising 0.25 wt% of the MWCNTs and 0.30 wt% of titania (anatase structure) were synthesized in a two-stage procedure using the electrophoretic deposition...
-
Vibration Surveillance System with Variable Stiffness Holder for Milling Flexible Details
PublicationEfficient milling of the flexible details (i.e. rotor blades, thin-walled elements) using slender ball-end tools is a difficult task due to possibility of vibration occurrence. Because of the existence of certain conditions (small depths of cutting, regeneration phenomena), cutting process may lose stability and self-excited chatter vibration may appear. Frequency of the chatter vibration is close to dominant natural frequency...
-
Surface finite viscoelasticity and surface anti-plane waves
PublicationWe introduce the surface viscoelasticity under finite deformations. The theory is straightforward generalization of the Gurtin–Murdoch model to materials with fading memory. Surface viscoelasticity may reflect some surface related creep/stress relaxation phenomena observed at small scales. Discussed model could also describe thin inelastic coatings or thin interfacial layers. The constitutive equations for surface stresses are...
-
Cavitation Erosion Resistance Influence of Material Properties
PublicationThe cavitation erosion is the phenomena that causes degradation of fluid flow machinery components due to repetitive implosion of cavitation bubbles adjacent to the solid surface. Cavitation erosion is a complex phenomenon, which includes not only hydrodynamic factors of liquid, but also properties of erodible material e.g. microstructure, hardness or Young modulus. In order to reduce the negative impact of erosion on machine components,...
-
Theoretical and Actual Feed Per Tooth During Wood Sawing on an Optimizing Cross-Cut Saw
PublicationThe work presents the geometries of circular saw teeth, whose task is to divide the cross-cut of the cutting layer. For efficient machining on a cross-cut saw with high feed speed values (about 1 ms−1) maximal theoretical feeds per tooth are determined. These values were compared with the actual values determined during transverse cutting of pine wood on a special test stands in industrial conditions. In the experiment the rotational...
-
Capacity of Surface Production of Band Sawing in Manufacture of Oak Floor Upper Layers
PublicationThin lamellae, corresponding to the layer components of structural glued members, i.e., 2-ply or 3-ply glued flooring, can be manufactured in re-sawing operations of kiln-dried wood blocks or in wet technologies, which currently seem to be more common because of the shorter drying time. The re-sawing process in wet technology is conducted on dedicated thin-cutting band sawing machines with stellite-tipped band saws. The goal of...
-
Designing control strategies of aeration system in biological WWTP
PublicationThe paper presents the complete design processes of a novel aeration control systems in the SBR (Sequencing Batch Reactor) wastewater treatment plant (WWTP). Due to large energy expense and high influence on biological processes, the aeration system plays a key role in WWTP operation. The paper considers the aeration system for a biological WWTP located in the northeast of Poland. This system consists of blowers, the main collector...
-
Polyurethanes for Coating, Adhesives, and Other Applications
PublicationAn interesting group of polyurethane (PU) materials are coatings, adhesives, sealants, and thickeners. A wide base of raw materials and various methods of PU synthesis allows production of materials with a wide range of properties that can be commonly used in many industries. This chapter describes the main types of PU coatings and adhesives and special application PUs and the methods of their production. The materials described...
-
Characteristics of silver-dopped carbon nanotube coating destined for medical applications
PublicationCarbon nanotubes are materials demonstrating outstanding mechanical, chemical, and physical properties and are considered coatings of titanium implants. The present research is aimed to characterize the microstructure and properties of the multi-wall carbon nanotubes (MWCNTs) layer decorated with silver nanoparticles (Ag NPs) on the Ti13Nb13Zr alloy destined for long-term implants. The electrophoretic deposition of coatings...
-
Przydatność urządzenia zmechanizowanego do wyznaczania trwałości ściernic do przecinania ręcznego
PublicationW artykule przedstawiono porównawcze wyniki badań trwałości ściernic do przecinania ręcznego, zużywanych na dwóch urządzeniach: z całkowicie ręcznym prowadzeniem przez operatora narzędzia i na urządzeniu zautomatyzowanym symulującym warunki przecinania ręcznego ściernicą. Wykazano, że dla tych dwóch urządzeń nie ma istotnej statystycznie korelacji pomiędzy wartościami wskaźnika wydajności względnej GA, reprezentującego trwałość...
-
The Thin-Layer Microchromatography (μTLC) and TLC–FID Technique as a New Methodology in the Study of Lubricating Oils
PublicationThis paper concerns the possibility of using TLC coupled with a flame ionization detector (FID) and micro-TLC (μTLC) as precursors for microfluidized devices of analytical techniques to identify and determine the presence and content of the petroleum/vegetable oil base in the lubricating oils applied in cutting devices (chainsaws). This research is related to the problem of ensuring, in compliance with the requirements of environmental...
-
Low-dimensional bound entanglement with one-way distillable cryptographic key
PublicationIn this paper, we provide a class of bound entangled states that have positive distillable secure key rate. The smallest state of this kind is 4 circle times 4, which shows that peculiar security contained in bound entangled states does not need high-dimensional systems. We show that for these states a positive key rate can be obtained by one-way Devetak-Winter (DW) protocol. Subsequently, the volume of bound entangled key-distillable...
-
Silica-Based Ionogels: Nanoconfined Ionic Liquid-Rich Fibers for Headspace Solid-Phase Microextraction Coupled with Gas Chromatography–Barrier Discharge Ionization Detection
PublicationIn this work, hybrid silica-based materials with immobilized ionic liquids (ILs) were prepared by sol–gel technology and evaluated as solid-phase microextraction (SPME) fiber coatings. High loadings of the IL 1-methyl-3-butylimidazolium bis(trifluoromethylsulfonyl)imide ([C4MIM][TFSI]) were confined within the hybrid network. Coatings composition and morphology were evaluated using scanning electron microscopy and energy dispersive...
-
Influence of Surface Modification of Titanium and Its Alloys for Medical Implants on Their Corrosion Behavior
PublicationTitanium and its alloys are often used for long-term implants after their surface treatment. Such surface modification is usually performed to improve biological properties but seldom to increase corrosion resistance. This paper presents research results performed on such metallic materials modified by a variety of techniques: direct voltage anodic oxidation in the presence of fluorides, micro-arc oxidation (MAO), pulse laser treatment,...
-
The determinants of morphology and properties of the nanohydroxyapatite coating deposited on the Ti13Zr13Nb alloy by electrophoretic techniqe
PublicationThe titanium and its alloys belong at present to the most preferred and commonly applied biomaterials for load- bearing implants. The surfaces of biomaterials are subjected to modification, including the hydroxyapatite coatings deposited in order to ensure corrosion resistance and better joining between an implant and a bone through the possibility of ingrowth bone into the coating. In this paper, the morphology and properties...
-
Hydroxyapatite deposition on the laser modified Ti13Nb13Zr alloy
PublicationThe Ti13Nb13Zr alloy was subjected to laser modification with the Nd:YAG laser provided that such treatment would increase the surface roughness followed improved adhesion of hydroxyapatite (HAp) coatings The hydroxyapatite was deposited by electrophoretic method in suspension of 0.5 g HA powder and 100 ml ethyl alcohol. The deposition was carried out for 10 min at 10 V voltage followed by drying at room temperature for 24 h and...
-
Study of a Multicriterion Decision-Making Approach to the MQL Turning of AISI 304 Steel Using Hybrid Nanocutting Fluid
PublicationThe enormous use of cutting fluid in machining leads to an increase in machining costs, along with different health hazards. Cutting fluid can be used efficiently using the MQL (minimum quantity lubrication) method, which aids in improving the machining performance. This paper contains multiple responses, namely, force, surface roughness, and temperature, so there arises a need for a multicriteria optimization technique. Therefore,...
-
Diagnosis of Damage in a Steel Tank Model by Shaking Table Harmonic Tests
PublicationDiagnosis of damage in civil engineering structures has recently become an important issue in the safety assessment procedure. Among a number of different approaches, a method of measuring the changes in natural frequencies is one of the most effective indicators of global damage. It has been successfully applied to relatively small. structures, however, the tests on large structures are very difficult and the practical application...
-
Thermal and technological aspects of double face grinding of Al2O3 ceramic materials
PublicationDouble face grinding with planetary kinematics is a process to manufacture workpieces with plan parallel functional surfaces, such as bearing rings or sealing shims. In order to increase the economic efficiency of this process, it has to be advanced permanently. The temperature in the contact zone of most grinding processes has a huge influence on the process efficiency and the workpiece qualities. In contrast to most grinding...
-
Thermal and technological aspects of double face grinding of C45 carbon steel
PublicationIn grinding, the contact zone temperature is a decisive factor influencing the achievable surface quality and the grinding tool wear. In contrast to other grinding processes, only few information regarding double face grinding with planetary kinematics when processing steel is known up to date. Since the successive substitution of in-dustrial double-sided lapping processes by double-sided grinding, it has become necessary to the...
-
Tilting pad thrust bearing with novel material selection - experimental comparison of low and medium speed operation
PublicationThe advances in material engineering led to the development of hard carbon based coatings applied in numerous applications in order to prevent or minimize wear of the parts in contact. With Triondur® coatings, the bearing company Schaeffler has succeeded in halving the friction losses in the valve trains of passenger cars. The coatings are optimized for high abrasive wear protection and low sliding friction moments. Altogether...
-
Protective properties of Al2O3 + TiO2 coating produced by the electrostatic spray deposition method
PublicationMechanical resistance of Al2O3 + TiO2 nanocomposite ceramic coating deposited by electrostatic spray deposition method onto X10CrAlSi18 steel to thermal and slurry tests was investigated. The coating was produced from colloidal suspension of TiO2 nanoparticles dispersed in 3 wt% solution of Al2(NO3)3, as Al2O3 precursor, in ethanol. TiO2 nanoparticles of two sizes, 15 nm and 32 nm, were used in the experiments. After deposition,...
-
Distribution of roughness and waviness components of turned surface profiles
PublicationThe paper presents a spectral formulation of surface profile irregularity in a wideband frequency range for roughness, waviness and shape components along the measured length. A unique distribution of roughness and waviness components is proposed, according to the nature of their origination in the course of machining with tools of defined cutting edge, as distinct from standard filtration in measurements of surface irregularities....
-
Research on the wear evenness of the tool in flat lapping
PublicationIn this paper, the dimensionless distribution of the material removal stock and the trajectories of abrasive grains cutting in single-sided lapping process are presented. They were numerically simulated based on the tribological model and kinematics equations. It can be observed that the trajectories geometry of single abrasive as well the velocities have a great influence on the final geometrical deviation. During machining, the...
-
Representing and Managing Experiential Knowledge with Decisional DNA and its Drimos® Extension
PublicationThe Semantic Web concept is proposing a future concept of the WorldWideWeb (WWW) where both humans and man-made systems are able to interconnect and exchange knowledge. One of the challenges of Semantic Web is smart and trusted accommodation of knowledge in artificial systems so it can be unified, enhanced, reused, shared, communicated and distributed with added aptitude. Our research represents an important component of addressing...
-
Effective yttrium based coating for steel interconnects of solid oxide cells: Corrosion evaluation in steam-hydrogen atmosphere
PublicationThis work describes manufacture, analysis and test of a new well conducting corrosion-protection coating that can be applied on steel types with high chromium content. Electrolytic deposition of yttrium salts is used to form thin (<100 nm) coatings on both flat steel sheets (material: Crofer 22 APU) and its properties are proven on woven wire-meshes (materials from two different sources: SUS316 and SUS316L). The oxide scale on...
-
Non-Isocyanate-Based Waterborne Polyurethanes
PublicationNon-isocyanate polyurethanes (NIPUs) are a greener alternative for the conventional polyurethanes synthesized using toxic and moisture-sensitive di- or polyisocyanates. The most often described method of NIPU synthesis involves the reaction of five-membered cyclic carbonates with amines, and resulting polymers containing primary and secondary hydroxyl groups (so they are also known as polyhydroxyurethanes), which can be further...
-
Recent advances in electrochemically surface treated titanium and its alloys for biomedical applications: A review of anodic and plasma electrolytic oxidation methods
PublicationNowadays, titanium and its alloys are widely used materials in implantology. Nevertheless, the greatest challenge is still its appropriate surface treatment in order to induce optimal properties, which facilitates formation of a permanent bond between the implant and human tissue. The use of electrochemical treatment such as anodic oxidation or plasma electrolytic oxidation allows for the production of porous coating that mimics...
-
Diagnosis of Damage in a Steel Tank with Self-Supported Roof through Numerical Analysis
PublicationThe safety of civil engineering structures is one of the most important issues of building industry. That is why the assessment of the damage-involved structural response has recently become of major concern to engineers. Among a number of different approaches to diagnosis of damage, the method of measuring the changes in natural frequencies is considered to be one of the most effective indicators of global damage. From the practical...
-
Problemy przyłączania farm wiatrowych do systemu elektroenergetycznego z wykorzystaniem kabli WN
PublicationArtykuł prezentuje problemy, jakie rodzi przyłączanie farm wiatrowych do systemu elektroenergetycznego za pomocą kabli wysokiego napięcia. Autor wskazuje możliwe problemy z kompensacją mocy biernej, w zależności od sposobu przyłączenia dławika kompensacyjnego i nastawień układów regulacji mocy biernej oraz napięcia farmy wiatrowej. Artykuł porusza też zagadnienia zwiększenia strat mocy czynnej powodowanych instalacją dławików kompensacyjnych.
-
Analysis of Ferroresonance Mitigation Effectiveness in Auxiliary Power Systems of High-Voltage Substations
PublicationFerroresonance in power networks is a dangerous phenomenon, which may result in overcurrents and overvoltages, causing damage to power equipment and the faulty operation of protection systems. For this reason, the possibility of the occurrence of ferroresonance has to be identified, and adequate methods need to be incorporated to eliminate or reduce its effects. The aim of this paper is to evaluate the effectiveness of ferroresonance...
-
Modeling a Traffic Remapping Attack Game in a Multi-hop Ad Hoc Network
PublicationIn multi-hop ad hoc networks, selfish nodes may unduly acquire high quality of service (QoS) by assigning higher priority to source packets and lower priority to transit packets. Such traffic remapping attacks (TRAs) are cheap to launch, impossible to prevent, hard to detect, and harmful to non-selfish nodes. While studied mostly in single-hop wireless network settings, TRAs have resisted analysis in multi-hop settings. In this paper...
-
Effect of double thermal and electrochemical oxidation on titanium alloys for medical applications
PublicationThe research focuses on the development and characterization of innovative thin hybrid oxide coatings obtained in subsequent processes of thermal (TO) and electrochemical (EO) oxidation. Four different surface modifications were investigated and the microstructure was determined, the mechanical, chemical and biological properties of the Ti-13Nb-13Zr alloy were assessed using scanning electron microscopy, X-ray dispersion analysis,...
-
Influence of dispersed phase content on the mechanical properties of electroless nanocomposite Ni-P/Si3N4 and hybrid Ni-P/Si3N4/graphite layers deposited on the AW-7075 alloy.
PublicationThe article presents the results of mechanical testing of Ni-P/Si3N4 nanocomposite and hybrid Ni-P/Si3N4/graphite coatings deposited on AW-7075 aluminum alloy using the chemical reduction method. In terms of mechanical testing, microhardness was measured, and surface roughness and adhesion of the coatings to the aluminum substrate were determined using the “scratch test” method. The surface morphology of the deposited layers was...
-
System load impact on VRRP advertisements delay
PublicationThe aim of the paper is to show how system load can affect network tasks (especially VRRP advertising depending on factors such as kernel schedu-ler [3] version, kernel settings and load priority. Two versions of the Linux kernel will be used: 2.6.22 (with "O(1) scheduler) and 2.6.23 (with "CFS" scheduler). "vrrpd" version 0.4 is used as an VRRP protocol implementation.
-
Resonant Conditions in a Node with an SVC Compensator
PublicationThe primary purpose of installing static shunt compensators in power grids is to improve the voltage conditions. Additional reactive power sources increase the system’s voltage stability and enable faster system recovery after a voltage failure. This paper presents the impact of an SVC device’s structure and settings on impedance change in the supply system, and hence on the frequencies at which resonance phenomena can develop.
-
Polyethylene glycol-coated solid-phase microextraction fibres for the extraction of polar analytes-A review
PublicationThe article discusses the merits and limitations of commercially available solid-phase microextraction (SPME) fibres and compares them with the new type of extraction coatings, in particular those containing polyethylene glycol as sorbent, as well as the methods of the preparation of the latter. It also analyses their possible application for the extraction of a broad spectrum of analytes, with particular emphasis on the sampling...
-
Problems of Connecting Wind Farms to the Power System with HV Cables
PublicationThis paper presents problems caused by connecting wind farms to a power system with high voltage cables. The author highlights possible problems with reactive power compensation, depending on the arrangement of the shunt reactor connection and settings of control systems for reactive power and voltage of the wind farm. The paper also discusses issues of increasing active power losses caused by a shunt reactor installation.