Filters
total: 1306
filtered: 1071
displaying 1000 best results Help
Search results for: LUBRICATING OILS
-
Water-Lubricated Journal Bearings Marine Applications, Design, and Operational Problems and Solutions
PublicationWater-Lubricated Journal Bearings: Marine Applications, Design, and Operational Problems and Solutions provides cutting-edge design solutions, common problems and methods for avoiding them, and material selection considerations for the use of water-lubricated journal bearings in marine environments. These bearings have many advantages, including the absence of the potential for oil contamination. They are also sensitive, and their...
-
Effect of alkyl sulfate on the phase behavior of microemulsions stabilized with monoacylglycerols
PublicationIn this study the effect of an anionic surfactant (sodium dodecyl sulfate SDS) and oils (hydrocarbons: C12-C16) on the formation and phase behavior of the systems of oil/monoacylglycerols (MAG):SDS/propylene glycol/water has been investigated. The effects of the surfactant mixture on the phase behavior and the concentrationof water or oil in the systems were studied at three temperatures (50, 55, 60 C). Electrical conductivity...
-
Understanding the early-stage release of volatile organic compounds from rapeseed oil during deep-frying of tubers by targeted and omics-inspired approaches using PTR-MS and gas chromatography
PublicationDuring deep-frying, a plethora of volatile products is emitted with the fumes. These compounds could act as oil quality indicators and change the indoor air composition leading to health risks for occupants. The presented experiments focus on deep-frying of different tubers in rapeseed oil at different frying temperatures. Here, two scenarios for real-time monitoring of volatile organic compounds (VOCs) using proton transfer reaction...
-
Probabilistic analysis of settlements under a pile foundation of a road bridge pylon
PublicationThe paper addresses the reliability change of a road bridge pile foundation due to the unpredictable increase of settlements in time. The analysis is based on the Rędziński Bridge in Wrocław, Poland, its design assumptions, and monitoring results. The bridge foundation rests on a multi-layered subsoil assumed random. The Finite Element model of the subgrade is generated in ZSoil® software. To simplify the probabilistic approach,...
-
Incorporating installation effects into the probability analysis of controlled modulus columns
PublicationThis technical report presents the probabilistic analysis which integrates the Monte Carlo simulation (MCS) with random field theory to model the load–displacement behavior of Controlled Modulus Columns (CMCs) in overconsolidated Poznań clay. Presented study focuses on the practical aspects of statistical analysis of geotechnical data, numerical model development, and results evaluation. Variability and spatial distribution of...
-
Analysis of Ceramic Elements with Ring-Crack Defects in Lubricated Rolling Contact
PublicationThe properties of ceramics, specifically low density, high hardness, high temperature capability and low coefficient of thermal expansion are of most interest to rolling element manufacturers. Surface ring cracks on lubricating rolling contact fatigue failure has been studied using numerical fracture analysis. Such cracks are very often found on ceramic bearing balls and decrease fatigue life rapidly. The numerical calculations...
-
On the Possibilities of Decreasing Power Loss in Large Tilting Pad Thrust Bearings
PublicationJournal Menu About this Journal Abstracting and Indexing Aims and Scope Article Processing Charges Articles in Press Author Guidelines Bibliographic Information Citations to this Journal Contact Information Editorial Board Editorial Workflow Free eTOC Alerts Publication Ethics Submit a Manuscript Table of Contents Abstract Full-Text PDF Full-Text HTML...
-
Grease effect on fretting wear of mild steel
PublicationNa stanowisku laboratoryjnym przeprowadzono badania zużycia frettingowego miękkiej stali smarowanej mineralnymi i syntetycznymi smarami zawierającymi także różne dodatki: grafit dwusiarczek molibdenu ZDDP i ditiocarbamat molibdenu, w różnych stężeniach.Badania wykazały istotny wpływ konsystencji smaru i jego właściwości smarnych na zużycie frettingowe miękkiej stali oraz zróżnicowany wpływ testowanych dodatków. Obecność smaru...
-
The problems of resistance to scuffing of heavily loaded lubricated friction joints with WC/C-coated parts
Publication -
Centrifugal magnetic fluid seals
PublicationSeals perform an important and at times overlooked function in a lubricant system. They prevent or minimize the movement of the lubricant between two surfaces and also minimize the level of contamination in the system. Seals are divided into static and dynamic types. Static seals operate in systems where the mating surfaces do not move relative to each other. In contrast, dynamic seals operate under conditions where the mating surfaces...
-
A multi-analytical approach to the characterization of natural organic dyestuffs and inorganic substrates present in the 19th-century artistic oil paints manufactured by a French art materials supplier Richard Aines
PublicationThis paper presents a comprehensive analysis of artistic paints produced in the 19th century by a French art materials supplier Richard Ain`es. Improved mild extraction with hydrofluoric acid enabled the observation of intact organic dyes. Reversed-phase liquid chromatography with diode-array and mass spectrometry detection was utilised for the identification of 35 dyes present in yellow and red paint samples, and in selected plant...
-
WATER LUBRICATED MAIN SHAFT BEARINGS - MODERN SOLUTION FOR HYDROPOWER INDUSTRY - Experimental and theoretical studies
PublicationWater-lubricated bearings are finding increasingly wide use in various branches of industry. As such, they may also be encountered in hydro power industry. They are also increasingly frequently employed in bearing systems of marine shaft propulsions and water pumps [1]. This rising popularity is due to a number of reasons [2]. First of all, their simple construction has direct impact on the level of pricing which is usually quite...
-
Accumulation of volatile constituents in agar and bioreactor shoot cultures of Verbena officinalis L.
PublicationIn vitro shoot cultures of common vervain (Verbena officinalis L., Verbenaceae) were established and evaluated for essential oil content. The shoots were maintained as stationary microshoot culture, grown on Schenk–Hildebrandt medium supplemented with 9.84 µM of 2-isopentenyladenine and 1.0 µM of thidiazuron. The shoots were further adapted to grow in two temporary immersion bioreactors (RITA and Plantform), using Schenk–Hildebrandt...
-
On the existence of homoclinic type solutions of inhomogenous Lagrangian systems
PublicationWe study the existence of homoclinic type solutions for a class of inhomogenous Lagrangian systems with a potential satisfying the Ambrosetti-Rabinowitz superquadratic growth condition and a square integrable forcing term. A homoclinic type solution is obtained as a limit of periodic solutions of an approximative sequence of second order differential equations.
-
Homoclinics for singular strong force Lagrangian systems in R^N
PublicationWe will be concerned with the existence of homoclinics for second order Hamiltonian systems in R^N (N>2) given by Hamiltonians of the form H(t,q,p)=Φ(p)+V(t,q), where Φ is a G-function in the sense of Trudinger, V is C^2-smooth, periodic in the time variable, has a single well of infinite depth at a point ξ and a unique strict global maximum 0 at the origin. Under a strong force type condition aroud the singular point ξ, we prove...
-
The equivariant spectral flow and bifurcation of periodic solutions of Hamiltonian systems
PublicationWe define a spectral flow for paths of selfadjoint Fredholm operators that are equivariant under the orthogonal action of a compact Lie group as an element of the representation ring of the latter. This G-equivariant spectral flow shares all common properties of the integer valued classical spectral flow, and it can be non-trivial even if the classical spectral flow vanishes. Our main theorem uses the G-equivariant spectral flow...
-
The Maslov index and the spectral flow—revisited
PublicationWe give an elementary proof of a celebrated theorem of Cappell, Lee and Miller which relates the Maslov index of a pair of paths of Lagrangian subspaces to the spectral flow of an associated path of self-adjoint first-order operators. We particularly pay attention to the continuity of the latter path of operators, where we consider the gap-metric on the set of all closed operators on a Hilbert space. Finally, we obtain from Cappell,...
-
On the Existence of Homoclinic Type Solutions of a Class of Inhomogenous Second Order Hamiltonian Systems
PublicationWe show the existence of homoclinic type solutions of a class of inhomogenous second order Hamiltonian systems, where a C1-smooth potential satisfies a relaxed superquadratic growth condition, its gradient is bounded in the time variable, and a forcing term is sufficiently small in the space of square integrable functions. The idea of our proof is to approximate the original system by time-periodic ones, with larger and larger...
-
Anomalous Behavior of Hyaluronan Crosslinking Due to the Presence of Excess Phospholipids in the Articular Cartilage System of Osteoarthritis
PublicationLubrication of articular cartilage is a complex multiscale phenomenon in synovial joint organ systems. In these systems, synovial fluid properties result from synergistic interactions between a variety of molecular constituent. Two molecular classes in particular are of importance in understanding lubrication mechanisms: hyaluronic acid and phospholipids. The purpose of this study is to evaluate interactions between hyaluronic acid...
-
Can matrix solid phase dispersion (MSPD) be more simplified? Application of solventless MSPD sample preparation method for GC–MS and GC–FID analysis of plant essential oil components
Publication -
Uwodornienie oleju sojowego i rzepakowego na katalizatorach miedziowych promotorowanych niklem i tlenkiem glinu. Hydrogenation of soybean and rapeseed oil with copper catalysts activated with nickel and aluminium oxide
PublicationBadano nowy typ katalizatorów miedziowych promotorowanych niklem, o stosunku Cu do Ni w granicach od 1:0,0036 do 1:0,018 w?w, osadzonych na Al2O3, przeznaczonych do selektywnego uwodornienia kwasu linolenowego w olejach roślinnych. Uwodornienie prowadzono w laboratoryjnym reaktorze typu "dead end" na oleju sojowym i rzepakowym, a kontakty mieszane - w stęż. 0,5% i 1% Cu. Na podstawie badań stwierdzono, że promotorowanie znacząco...
-
Porównanie przebiegu enzymatycznej hydrolizy oleju rzepakowego i strukturyzowanych lipidów zawierających kwas behenowy. The comparision on the course of enzymatic hydrolysis of rapeseed oil and structured lipids containing behenoic acid.
PublicationPorównywano przebieg enzymatycznej hydrolizy oleju rzepakowego i strukturyzowanych lipidów zawierających kwas behenowy (C22:0). Hydroliza prowadzona była w obecności lipazy trzustkowej, w warunkach stymulujących proces trawienia. Stwierdzono, że olej rzepakowy hydrolizowany jest znacznie szybciej niż strukturyzowane lipidy z kwasem behenowym.
-
Analiza i ocena smarności olejów w ujęciu energetycznym i działania układu tribologicznego = Analysis and evaluation of oil lubricity from the viewpoint of energy apects and of the tribological system action
PublicationBased on measurement results, an interpretation is presented of the tribological system boundary layer action in the form of a four-ball tester friction node. The evaluation was performed of the boundary layer action understood as transfer of energy Ep resulting from loading the tribological system in a determined time t with work Lp, which may lead to breaking the boundary layer. That energy and time are the values unequivocally...
-
Fluctuation-enhanced scent sensing using a single gas sensor
PublicationScent or aroma sensing during aromatherapy can be carried out by applying only a single resistance gas sensor (TGS - Taguchi Gas Sensors). This paper considers the efficiency of detection of essential oils by DC resistance and its fluctuations observed in TGS sensors. A detailed study has been conducted for scents emitted by five popular essential oils using three sensor types (TGS 2600, TGS 2602, TGS 823). The research was focused...
-
High resolution liquid chromatography and time of flight mass spectrometry in perfume analysis
PublicationPerfumes consist of a wide range of natural and synthetic compounds that belongs to different chemical classes. Most of these compounds are generally determined by GC. However, in this study RP-HPLC-Q-TOF-MS and HILIC-Q-TOF-MS technique was applied for the determination of ingredients of original perfumes and their imitations. Antioxidants and compounds specific to fragrances of animal \origin were found in original...
-
Water-lubricated stern tube bearing - experimental and theoretical investigations of thermal effects
PublicationThe paper presents research results of thermal phenomena accompanying operation of a water-lubricated stern tube bearing with axial grooves. Experimental tests revealed, that intensity of forced axial flow has strong influence on bush temperature. Numerical simulations focused on investigation of the thermal phenomena under operation of water-lubricated journal bearing showed, that restricted axial flow promotes backflow of the...
-
Comments on Identification and Determination of Volatile Chloroorganic Compounds in Crude Oil at Trace Level = Komentarz na temat identyfikowania i oznaczania śladowych ilości lotnych związków chloroorganicznych w ropie naftowej
PublicationW pracy przedstawiono możliwości i ograniczenia w stosowaniu techniki GC-ECD i GC-MS do identyfikacji i oznaczania śladowych stężeń związków chloroorganicznych w destylatach z ropy naftowej (frakcjach wrzących do 200oC). Przedyskutowano także procedury rutynowo stosowane w rafineriach do oznaczania zawartości chloru organicznego. Należą do nich metodyki oparte na spalaniu próbki i oznaczaniu wybranych produktów mineralizacji za...
-
What should we know when choosing feather, blood, egg or preen oil as biological samples for contaminants detection? A non-lethal approach to bird sampling for PCBs, OCPs, PBDEs and PFASs
PublicationBirds are considered as good bio-monitors and they can provide highly valuable data about the level of contamination in their habitat. During the design of biomonitoring studies one of the first issues after choosing species is the choice of biological material. Non-lethally collected samples have recently been gaining greater attention as they offer several ethical and practical advantages. However, not all sample matrices are...
-
Technologie stosowane do otrzymywania tłuszczów smażalniczych.
PublicationPodano technologie, które mają lub mogą mieć zastosowanie do otrzymywania tłuszczów smażalniczych. Są to: heterogeniczne uwodornienie na katalizatorach metalicznych, głównie niklowych, frakcjonowana krystalizacja, mieszanie tłuszczów lub ich przeestryfikowanie. Przedstawiono wybrane oleje pozyskiwane z roślin oleistych poddanych modyfikacji genetycznej składu kwasów tłuszczowych. Omówiono zalety i wady każdej z metod modyfikacji...
-
Floe-size distributions in laboratory ice broken by waves
Publication -
Floe-size distributions in laboratory ice broken by waves
Publication -
Floe-size distributions in laboratory ice broken by waves
Publication -
GRAPHENE IN GAS CHEMIRESISTORS
PublicationGraphene has a range of unique physical properties which could be exploited in gas sensing. Every atom of graphene may be considered as a surface atom, able to interact even with single molecule of the target gas or vapour species resulting in the ultrasensitive sensor response. In this paper the potential of graphene as a nanomaterial for fabricating chemiresistors was described. Recent development in graphene sensors was considered...
-
The effect of the exposure-in-oil on the contact of the polymers forming sliding layers in hydrodynamic bearings. Wpływ ekspozycji w oleju na kąt zwilżania polimerów stosowanych na warstwy ślizgowe w łożyskach hydrodynamicznych.
PublicationPolimery stosowane jako warstwy ślizgowe w hydrodynamicznych łożyskach wzdłużnych to zazwyczaj tworzywa termoplastyczne charakteryzujące się relatywnie wysokimi wartościami kątów zwilżania w porównaniu z metalami. Metale, w tym również Babbitt czy inne stopy łożyskowe, cechują niskie wartości kątów zwilżania. Im niższy kąt, tym powierzchnia lepiej się zwilża. Tworzywa sztuczne wykorzystywane w węzłach tribologicznych mających zapewnić...
-
Microemulsion Delivery Systems with Low Surfactant Concentrations: Optimization of Structure and Properties by Glycol Cosurfactants
PublicationExtensive use of microemulsions as delivery systems raises interest in the safe ingredients that can form such systems. Here, we assessed the use of two glycols, i.e., propylene glycol and pentylene glycol, and their mixtures to manipulate the properties and structure of microemulsions. Obtained systems with glycols were extensively characterized in terms of capacity to incorporate water phase, droplet size, polydispersity, structure...
-
Multivariate evaluation by quality indicators of no-tillage system in Argiudolls of rolling pampa (Argentina)
Publication -
Assessment of the potential for dredged material dispersal from dumping sites in the Gulf of Gdańsk
Publication -
Long-term changes and distribution of mercury concentrations in surface sediments of the Gdansk Basin (Southern Baltic Sea)
Publication -
Seasonal changes of mercury speciation in the coastal sediments
PublicationPurpose Mercury speciation in sediments is linked to environmental conditions and processes. Domination of particular mercury species depends on its source, displays considerable seasonal behavior, and may be further modified due to oxygen levels, icing conditions, or the input of fresh organic matter. The purpose of this study was to examine the coastal area of the Gulf of Gdańsk in terms of mercury contamination and the influence...
-
Wysokociśnieniowe uszczelnienia ruchu obrotowego wału hydraulicznych maszyn wyporowych
PublicationW artykule przedstawiono wyniki badań mające na celu wytypowanie węzła uszczelniającego wał silnika hydraulicznego zapewniającego najwyższą trwałość przy smarowaniu wodą. Parametry pracy: ciśnienie 2 MPa i minimalna prędkość poślizgu uszczelek 2 m/s. Opisano również nowatorski przyrząd, na którym przeprowadzono pomiary wszystkich parametrów węzła uszczelniającego.
-
Nitrogen dioxide sensing properties of PEDOT polymer films
PublicationThis work presents a simple and fully electrochemical route for the polymerization of poly(3,4-ethylenedioxytiophene) (PEDOT) films for fabricating a NO2 gas sensor prepared by electropolymerization of 3,4-Ethylenedioxythiophene (EDOT) monomer in lithium perchlorate/acetonitrile solution. The main aim of this study is to determine the sensing properties of conductive polymer at elevated temperatures. The effects of the humidity,...
-
Albumin–Hyaluronan Interactions: Influence of Ionic Composition Probed by Molecular Dynamics
PublicationThe lubrication mechanism in synovial fluid and joints is not yet fully understood. Nevertheless, intermolecular interactions between various neutral and ionic species including large macromolecular systems and simple inorganic ions are the key to understanding the excellent lubrication performance. An important tool for characterizing the intermolecular forces and their structural consequences is molecular dynamics. Albumin...
-
Investigating lubricants behaviour in microgravity for vibration damping purposes
PublicationVibration is one of the harshest environments an object is exposed to during and after launch into space on a launch vehicle. Such vibrations should be damped to avoid destruction of the spacecraft or its elements. Currently, active and material damping is used. A possibility of using lubrication as the damping factor is suggested by some research. MoS2 is a typical solid lubricant used in space applications. Its properties vary...
-
Bifurcation of equilibrium forms of an elastic rod on a two-parameter Winkler foundation
PublicationWe consider two-parameter bifurcation of equilibrium states of an elastic rod on a deformable foundation. Our main theorem shows that bifurcation occurs if and only if the linearization of our problem has nontrivial solutions. In fact our proof, based on the concept of the Brouwer degree, gives more, namely that from each bifurcation point there branches off a continuum of solutions.
-
Structure, morphology and mechanical behaviour of novel bio-based polyurethane composites with microcrystalline cellulose
PublicationThe aim of this work was to obtain bio-based polyurethane composites using biocomponents such as, bio-glycol, modified natural oil-based polyol, and microcrystalline cellulose (MCC). The prepolymer method was used to prepare the bio-based polyurethane matrix. Prepolymer synthesised from 4,4’-diphenylmethane diisocyanate (MDI) and a polyol mixture containing 75% wt. commercial polyether and 25% wt. hydroxylated soybean oils (H3)...
-
Intelligent microbearing project with memory of stress-strain history
PublicationTaking into account the increasing need of intelligent micro-bearing with memory, this paper presents the optimization, simulation and practical application of operating parameters(load carrying capacity, friction forces, friction coefficient, wear), simulation for hydrodynamic HDD micro-bearing with curvilinear nano-grooved journal profile. One of the reason of such journal profile is that this journal profile contributes to the...
-
Tribological performance of PTFE-metal binary coatings in rolling/sliding contact
PublicationTribological performance of surface coatings with embedded PTFE reservoirs in rolling/sliding contact is reported. Using two different coating materials and two shapes and patterns of PTFE reservoirs test samples in the form of discs were prepared and tested in a four-ball contact configuration under loads corresponding to nominal contact pressure of 0.5 and 1.0 GPa. It was found that one coating, namely aluminium-bronze with embedded...
-
APPLICATION OF THE THEORY OF SEMI-MARKOV PROCESSES TO DETERMINE A LIMITING DISTRIBUTION OF THE PROCESS OF CHANGES OF ABILITY AND INABILITY STATES OF FUEL SUPPLY SYSTEMS IN HEAVY FUEL DIESEL ENGINES
PublicationThe paper presents applicability of the theory of semi-Markov processes to determine a limiting distribution of the process of changes of technical states of fuel systems for marine engines running on heavy fuel oils. The proposed study of this process includes the components of such fuel systems like: 1 - injectors, 2 - high pressure hoses, 3 - injection pumps, 4 - low pressure hoses, 5 – fine filters, 6 - coarse filters, 7 – fuel-feed...
-
Fatigue resistance investigation of the IC engine MB11 bearings, working under conditions of dynamic unidirectional loadings
PublicationThe slide bearing material MB11 fatigue resistance has been investigated with the application of SMOK - test stand in which dynamic unidirectional loadings to the test bearing is generated. Slide bearing layer consists of the bronze MB11 ( Cu Pb22 Sn 3 ) sintered to the steel shell. Each of the tested bearing has been subject to the standard 20-hour test, under conditions of the full fluid lubrication. Methodology of the experiments,...
-
ANALYSIS OF THE LOAD-CARRYING CAPACITY OF A HYDRODYNAMIC WATER-LUBRICATED BEARING IN A HYDROELECTRIC POwER PLANT
PublicationThe paper presents an analysis of the load-carrying capacity of a historic hydrodynamic water-lubricated radial bearing of an unconventional segment design installed in the Braniewo Hydroelectric Power Plant. The aim of the calculations was to determine whether the bearing operates in the conditions of hydrodynamic or mixed lubrication, as well as to establish the optimal geometry of the axial grooves allowing for the highest load-carrying...