Search
Filters
total: 3753
filtered: 3149
displaying 1000 best results Help
Search results for: FRICTION RESISTANCES
-
Methods of Tire Rolling Resistance Measurements
PublicationTire rolling resistance is one of the factors related to tire/road interaction that has important influence on road vehicles performance. Raising fuel price and increased concern related to the environmental changes result in growing interest in reduction of tire rolling resistance that influences fuel consumption, especially in free-flowing highway traffic with moderate speeds. There are several methods of tire rolling resistance measurements....
-
Type of surface and tire rolling resistance
Publication...
-
The resistance of S235JR steel to cavitation erosion
PublicationThe erosion resistance of S235JR steel to flow cavitation was investigated. In order to understand an influence of steel properties and cavitation intensities on the degradation mechanisms, low-carbon S235JR steel was tested in the as-received state and after thermal treatment (annealing) under four different flow velocities. Annealing decreased steel hardness, which made S235JR steel less resistant to cavitation erosion. The performed...
-
Estimation of cavitation erosion resistance of materials
PublicationW pracy przedstawiono ocenę odporności kawitacyjnej 17 materiałów. Do opisu odporności kawitacyjnej zaproponowano nowy wskaźnik liczbowy uwzględniający długość okresu inkubacji, maksymalną prędkość niszczenia oraz czas po którym wystąpi maksymalna prędkość niszczenia materiału. Zaproponowany wskaźnik porównano ze wskaźnikiem δcav, który reprezentuje całą krzywą erozji kawitacyjnej materiału.
-
INFLUENCE OF TEMPERATURE ON THE TYRE ROLLING RESISTANCE
PublicationTemperature is a very important factor controlling rolling resistance of road vehicle tyres. There are at least three different temperatures that may be considered as important factors controlling thermal conditions of the rolling tyre. The most common measure of the thermal conditions during tyre rolling is ambient air temperature. The other two are: pavement temperature and “tyre” temperature. Tyre temperature is the most difficult...
-
Approaches to experiment based friction modeling: polynomial approximation versus ann approximation
PublicationBadano warunki (poziom wymuszeń), przy których następowało wzbudzenie drgań mechanicznych przy tarciu ślizgowym konforemnego skojarzenia próbek wykonanych z Al2O3 (płaskie czoło tulei obracającej się względem swojej osi - powierzchnia płaska). Uzyskane dane eksperymentalne wykorzystano następnie do zbudowania modeli - stosując aproksymację wielomianami albo sztuczną siecią neuronową (ANN).
-
Effects of surface texturing and kind of lubricant on the coefficient of friction at ambient and elevated temperatures
Publication -
Experimental Study of the Rolling Friction Coefficient in Highly Loaded Supports of Rotary Kilns
Publication -
Heat transfer enhancement, flow visualization and friction characteristics in rib-roughened channels
PublicationW pracy przedstawiono wyniki badań eksperymentalnych związanych z intensyfikacją wymiany ciepła w kanałach wyposażonych w żebra, które poprawiają warunki przejmowania ciepła od ścianki do przepływającego medium. W badaniach wykorzystano system PIV oraz termografię ciekłokrystaliczną.
-
Thermo-Mechanical Simulation of Underwater Friction Stir Welding of Low Carbon Steel
PublicationThis article investigates the flow of materials and weld formation during underwater friction stir welding (UFSW) of low carbon steel. A thermo-mechanical model is used to understand the relation between frictional heat phenomena during the welding and weld properties. To better understand the effects of the water environment, the simulation and experimental results were compared with the sample prepared by the traditional friction...
-
Tribological and nanoscale research on model friction couples intended for hip joint prostheses
Publication -
A Study on Emission of Airborne Wear Particles from Car Brake Friction Pairs
PublicationThe emission of airborne wear particles from friction material / cast iron pairs used in car brakes was investigated, paying special attention to the influence of temperature. Five low-metallic materials and one non-asbestos organic material were tested using a pin-on-disc machine. The machine was placed in a sealed chamber to allow airborne particle collection. The concentration and size distribution of 0.0056 to 10 μm particles...
-
Friction-Induced Oscillations of a Non-Asbestos Organic Pin Sliding on a Steel Disc
PublicationFriction-induced oscillations result in deterioration of performance of disc brakes and are generally undesired. We conduct experimental study of friction-induced oscillations in a non-asbestos organic material / steel pair used in disc brakes of motor vehicles. The tests are done by use of a pin-on-disc machine which has the pin sample supported on a deformable beam. The adjustable friction parameters are the disc velocity, contact...
-
A chemo-mechano-thermodynamical contact theory for adhesion, friction, and (de)bonding reactions
PublicationThis work presents a self-contained continuum formulation for coupled chemical, mechanical, and thermal contact interactions. The formulation is very general and, hence, admits arbitrary geometry, deformation, and material behavior. All model equations are derived rigorously from the balance laws of mass, momentum, energy, and entropy in the framework of irreversible thermodynamics, thus exposing all the coupling present in the...
-
Spleen: Consequences of Lack of Function
Publication -
The smoothness test for a density function
PublicationThe problem of testing hypothesis that a density function has no more than μ derivatives versus it has more than μ derivatives is considered. For a solution, the L2 norms of wavelet orthogonal projections on some orthogonal ‘‘differences’’ of spaces from a multiresolution analysis is used. For the construction of the smoothness test an asymptotic distribution of a smoothness estimator is used. To analyze that asymptotic distribution,...
-
A parametric method for evaluation of resistance of swath ships
PublicationArtykuł zawiera sformułowania metody parametrycznej służącej do wyznaczania oporu kadłuba statku o konfiguracji swath. Metodę opracowano opierając się na rezultatach obliczeń numerycznych, uzyskanych metodami strukturalnymi, wywiedzionymi ze sformułowań teoretycznej hydromechaniki okrętu, wykonanych na dostatecznie licznej serii kształtów kadłuba, o systematycznie uzmiennianych parametrach kształtu. Następnie przedstawiono rezultaty...
-
Tire rolling resistance measurements on the road and in the laboratory
PublicationW pracy przedstawiono stanowisko bębnowe do badania oporu toczenia opon samochdowych w warunkach laboratoryjnych. Zaprezentowano także przyczepę dynamometryczną do badania oporu toczenia opon samochodowych w warunkach drogowych. Stanowisko bębnowe i przyczepa zosały zbudowane w Katedrze Pojazdów i Maszyn Roboczych Politechniki Gdańskiej. Omówiono wpływ wzdłużnego pochylenia drogi i naporu powietrza na badane koło na dokładność...
-
Ship Resistance Prediction with Artificial Neural Networks
PublicationThe paper is dedicated to a new method of ship’s resistance prediction using Artificial Neural Network (ANN). In the initial stage selected ships parameters are prepared to be used as a training and validation sets. Next step is to verify several network structures and to determine parameters with the highest influence on the result resistance. Finally, other parameters expected to impact the resistance are proposed. The research utilizes...
-
Elctrochemical oxidation and corrosion resistance of the Ti13Nb13Zr alloy
PublicationThis paper presents the results of oxidation and corrosion tests carried out on titanium alloy Ti13Nb13Zr. The oxide film was prepared by electrochemical environment 2M H3PO4 for 30 min and 1 h, at a constant voltage 40V. The tests of corrosion resistance were performed by potentiostatic method in Ringer's solution at different pH values: 7, 5 and 3. The change in an appearance of surface and the increase in corrosion resistance...
-
Static puncture resistance of non-woven geotextiles
PublicationBadania cech fizycznych i wytrzymałościowych geowóknin separcyjnych i osłonowych. Analiza wyników badań oporu na przebicie statycze metodą CBR, dla różnych rodzajów geowłóknin, próbek pozyskanych z terenu (po wbudowaniu w nasyp)i kontrolnych.
-
Determination of the transverse resistance characteristics in railway track
PublicationW pracy przedstawiono problem oporów poprzecznych podsypki z punktu widzenia budowy, utrzymania oraz bezpieczeństwa w eksploatacji toru kolejowego. Zaprezentowano różne sposoby analitycznego podejścia do badanego zjawiska na przykładzie modeli matematycznych spotykanych w literaturze. Scharakteryzowano aktualny stan badań doświadczalnych związanych z oporami poprzecznymi. Omówiono różne sposoby prowadzenia takich badań w eksploatowanych...
-
Improvement of the resistance to oxidation of the ecological greases by the additives
Publication -
Road texture influence on tire rolling resistance
PublicationTire rolling resistance is one of the most important resistive forces acting on road vehicles. It depends on tire and surface characteristics as well as vehicle operating parameters. This paper deals with the influence of road surface texture on rolling resistance of passenger car tires. Results of road measurements performed on variety of road surfaces are presented.
-
Road texture influence on tyre rolling resistance
PublicationTyre performance, one of the critical factors for vehicle users, is strongly related to theroad surface characteristics, most notably to the pavement texture. Phenomena that occur at the tyre/road interface affect tyre friction (skid resistance), rolling resistance, tyre wear and tyre/road noise. This article deals with relationship between surface texture and rolling resistance of light and heavy vehicle tyres. Mean profile depth...
-
Engineering method of tire rolling resistance evaluation
PublicationTire rolling resistance is one of the most difficult tire parameters to measure. The reason is that for modern tires the force of rolling resistance corresponds to 0.5–1% of tire load, thus measurements of very small forces must be performed in a heavily loaded system. This constitutes great problems, especially in road conditions. Laboratory measurements are easier to perform, as the environment may be better controlled, but roadwheel...
-
Antimicrobial resistance of fecal indicators in disinfected wastewater
PublicationThe main objective of the study was to assess the potential of three systems (UV irradiation, ozonation, and micro/ultrafiltration) operated in a pilot scale in removal of antimicrobial-resistant fecal bacteria from secondary effluent of the local wastewater treatment plant (700,000 population equivalent). The effectiveness of the processes was analysed using the removal ratio of fecal indicators (Escherichia coli and Enterococcus...
-
Cavitation Erosion Resistance Influence of Material Properties
PublicationThe cavitation erosion is the phenomena that causes degradation of fluid flow machinery components due to repetitive implosion of cavitation bubbles adjacent to the solid surface. Cavitation erosion is a complex phenomenon, which includes not only hydrodynamic factors of liquid, but also properties of erodible material e.g. microstructure, hardness or Young modulus. In order to reduce the negative impact of erosion on machine components,...
-
The Resistance of Polyethersulfone Membranes on the Alkaline Cleaning Solutions
Publication -
Impact of probability distribution on the uncertainty of resistance measurement
PublicationThe paper presents studies on the influence of probability distributions on the expanded uncertainty of the resistance measurement. Choosing the correct probability distribution is very important to estimate of measurement uncertainty. The paper presents the results of analysis of the resistance measurement uncertainty using the technical method of resistance: 100 G. The analysis of the uncertainty...
-
Examination of the epoxy coating system's resistance to Corrobill
PublicationThe tests of the influence of the surface cleaning agent on the epoxy coating were carried out. Electrochemical and corrosion tests were carried out. The effect of the preparation on the adhesion and hardness of the tested coating was tested.
-
“The Guardians of the Truth”: Journalists’ Resistance to the Algorithmization of Journalism
PublicationRegardless of the term used, be it “robot journalism,” “automated journalism,” “algorithmic journalism” or “machine-written journalism,” the process of automatic content creation and distribution is progressing in the newsrooms. Meanwhile, exercising control over the creation and distribution of news is considered a fundamental element of journalists’ professional identity. The article presents the results of research on the perception...
-
FDTD-Compatible Green's function based on scalar discrete Green's function and multidimensional Z-transform
PublicationIn this contribution, a new formulation of the discrete Green's function (DGF) is presented for the finitedifference time-domain (FDTD) grid. Recently, dyadic DGF has been derived from the impulse response of the discretized scalar wave equation (i.e., scalar DGF) with the use of the multidimensional Z-transform. Its software implementation is straightforward because only elementary functions are involved and a single function...
-
SiC-Based Power Electronic Traction Transformer (PETT) for 3 kV DC Rail Traction
PublicationThe design of rolling stock plays a key role in the attractiveness of the rail transport. Train design must strictly meet the requirements of rail operators to ensure high quality and cost-eective services. Semiconductor power devices made from silicon carbide (SiC) have reached a level of technology enabling their widespread use in traction power converters. SiC transistors oering energy savings, quieter operation, improved reliability...
-
Torque Transmitted by Multi-plate Wet Clutches in Relation to Number of Friction Plates and Their Dimensions
PublicationIn the paper results of experimental tests on multi-plate wet clutch torque capacity for various diameters and numbers of friction plates are presented. Construction of an apparatus for laboratory tests of wet clutch engagement, drag torque and maximum torque is shown. Methodology of maximum torque capacity experiment and hydraulic circuit diagram, which supplies a motor and an actuator for the experiment are described. Analytically...
-
Manufacturing Parameters, Materials, and Welds Properties of Butt Friction Stir Welded Joints–Overview
PublicationThe modern and eco-friendly friction stir welding (FSW) method allows the combination of even such materials that are considered to be non-weldable. The development of FSW technology in recent years has allowed a rapid increase in the understanding of the mechanism of this process and made it possible to perform the first welding trials of modern polymeric and composite materials, the joining of which was previously a challenge....
-
Torque capacity of multidisc wet clutch with reference to friction occurrence on its spline connections
PublicationIn this article developed mathematical model that includes friction occurrence on spline connections is presented. The work also contains results of experimental research on torque capacity of multidisc wet clutch. These results are expressed as a function of contact pressure for different number of friction surfaces. Due to increased interest in research concerning multidisc wet clutches it is essential to determine impact of...
-
Friction Stir Welding of Aluminum in the Aerospace Industry: The Current Progress and State-of-the-Art Review
PublicationThe use of the friction stir welding (FSW) process as a relatively new solid-state welding technology in the aerospace industry has pushed forward several developments in different related aspects of this strategic industry. In terms of the FSW process itself, due to the geometric limitations involved in the conventional FSW process, many variants have been required over time to suit the different types of geometries and structures,...
-
Partition of friction heat between sliding semispaces due to adhesion-deformational heat generation
PublicationAnalytical expressions of heat-partition coefficient and contact temperatures for two sliding semispaces with account for adhesion-deformational heat generation and contact heat exchange have been obtained. The rate of deformational heat generation is assumed to decay exponentially with increase of distance from the interface. It has been shown that heat-generation configuration and the intensity of contact heat exchange have impact...
-
Correlations between the wear of car brake friction materials and airborne wear particle emissions
PublicationAirborne wear particles emitted from transport vehicle brakes are one of the main sources of toxic metals in inhalable particulate matter. Prediction of wear particle emissions may become more accurate if the relationship between the wear and particle emission characteristics is known. An experimental study was performed to investigate proportional correlations between the mass wear, 0.01–0.42 μm particle emission measured by a NanoScan...
-
Effects of Noncontact Shoulder Tool Velocities on Friction Stir Joining of Polyamide 6 (PA6)
PublicationIn this study, the effects of the traverse and rotational velocities of the noncontact shoulder tool on the heat generation and heated flux during the friction stir joining of high-density polyamide 6 (PA6) polymer were investigated. The computational fluid dynamics (CFD) method was employed to simulate the thermomechanical phenomena during the friction stir joining (FSJ) process of PA6. A developed model was used to consider the...
-
Study on Dry Sliding Wear and Friction Behaviour of Al7068/Si3N4/BN Hybrid Composites
PublicationHybrid aluminium metal matrix composites have the potential to replace single reinforced aluminium metal matrix composites due to improved properties. Moreover, tribological performance is critical for these composites, as they have extensive application areas, such as the automotive, aerospace, marine and defence industries. The present work aims to establish the tribological characteristics of Al7068/Si3N4/BN hybrid metal matrix...
-
Influence of friction stir welding technological parameters on the properties of the joints of selected aluminum alloys
PublicationThe purpose of this dissertation was to determine the effect of friction stir welding technological parameters on the properties of selected aluminum alloy joints, with consideration of the residual stresses and dislocation density in the joints. The goal of the present work was also to produce defect-free joints with high mechanical and electrochemical properties. In the dissertation, similar welds of AA6082 alloy and dissimilar...
-
Continuum contact model for friction between graphene sheets that accounts for surface anisotropy and curvature
PublicationUnderstanding the interaction mechanics between graphene layers and co-axial carbon nanotubes (CNTs) is essential for modeling graphene and CNT-based nanoelectromechanical systems. This work proposes a new continuum contact model to study interlayer interactions between curved graphene sheets. The continuum model is calibrated and validated using molecular dynamics (MD) simulations. These are carried out employing the reactive...
-
Effect of underwater friction stir welding parameters on AA5754 alloy joints: experimental studies
PublicationThe water as a welding environment may generate serious technological and metallurgical problems but in certain cases, the physicochemical properties of water can be used effectively, e.g., to impart the specific properties of welded materials. The purpose of the work was verification of effectiveness of the water cooling of aluminium alloy AA5754 for various sets of technological parameters of underwater friction stir welding...
-
Estimation of Screw Displacement Pile-Bearing Capacity Based on Drilling Resistances
PublicationThis article presents an engineering, empiricalmethod of estimating the bearing capacity and settlementcharacteristics Q-s of screw displacement piles andcolumns, based on soil resistance encountered during thedrilling to form piles/columns in the ground. The methodwas developed on the basis of correlation analyses of thetest results of 24 piles made during the “DPDT-Auger”research project (Krasiński et al., 2022a). In the proposedmethod,...
-
Bound on Bell inequalities by fraction of determinism and reverse triangle inequality
PublicationIt is an established fact that entanglement is a resource. Sharing an entangled state leads to nonlocal correlations and to violations of Bell inequalities. Such nonlocal correlations illustrate the advantage of quantum resources over classical resources. In this paper, we quantitatively study Bell inequalities with 2 × n inputs. As found in Gisin et al. [Int. J. Quantum. Inform. 05, 525 (2007)], quantum mechanical correlations...
-
Effective Drug Concentration and Selectivity Depends on Fraction of Primitive Cells
PublicationPoor efficiency of chemotherapeutics in the eradication of Cancer Stem Cells (CSCs) has been driving the search for more active and specific compounds. In this work, we show how cell density-dependent stage culture profiles can be used in drug development workflows to achieve more robust drug activity (IC50 and EC50) results. Using flow cytometry and light microscopy, we characterized the cytological stage profiles of the HL-60-,...
-
Pre-treatment of bio fraction waste prior to fermentation processes
PublicationCurrent efforts are taken to increase resource efficiency, close material loops, and improve sustainable waste and by-products management. Thus, networking agro-food by-products and converting them into valuable products completely exhausting the potential of the raw material becomes significant. Model lignocellulosic and starch based biomass were subjected to pre-treatment with the application of acidic compounds, i.e. sulphuric...
-
Closed forms of the Green's function and the generalized Green's function for the Helmholtz operator on the N-dimensional unit sphere
PublicationPokazano, że funkcję Greena dla operatora Helmholtza na N-wymiarowej sferze jednostkowej można wyrazić przez funcję Gegenbauera pierwszego rodzaju. W tych przypadkach, w których funkcja Greena nie istnieje, skonstruowano uogólnioną funkcję Greena.