Filters
total: 1755
filtered: 1627
displaying 1000 best results Help
Search results for: SELECTIVE SUBSTITUTION
-
The effect of Sr and Mg substitutions on structure, mechanical properties and solubility of fluorapatite ceramics for biomedical applications
PublicationIonic substitutions play important role in the modifications of biological apatites. Recently, attention has been focused on the co-doping effects on the functional properties of apatite-based biomaterials. In this research work, the dense samples of fluorapatites, Ca10(PO4)6F2 and Ca8MgSr(PO4)6F2, were produced after sintering at 1250 °C for 6 h in air. Structural characterization carried out with XRD, IR, Raman and SEM, confirmed...
-
Effect of isovalent substitution on microstructure and phase transition of LaNb1−xMxO4 (M=Sb, V or Ta; x=0.05–0.3)
PublicationLaNb1−xMxO4 oxides with pentavalent elements of different ionic sizes (M=Sb, Ta and V, x=0.05–0.3) were synthesized by the solid state reaction method. Special interest was devoted to the antimony substituted lanthanum niobate which is a new material in this group. Rietveld analysis of the X-ray diffraction patterns was used to determine the influence of the material composition on unit cell parameters. On the basis of dilatometric...
-
Phthalocyanines functionalized with 2-methyl-5-nitro-1H-imidazolylethoxy and 1,4,7-trioxanonyl moieties and the effect of metronidazole substitution on photocytotoxicity
Publication -
Tuning of eg electron occupancy of MnCo2O4 spinel for oxygen evolution reaction by partial substitution of Co by Fe at octahedral sites
PublicationTo study the effect of partial Co substitution by Fe in the B site of MnCo2O4 spinel on its physicochemical and electrochemical properties, a series of MnCo2-xFexO4 powders (x=0.125; 0.250; 0.500; 0.750; 1.000) were synthesized by means of the sol-gel method. The produced powders were characterized by powder X ray diffraction (pXRD), scanning and transmission electron microscopy (SEM & TEM) coupled with energy dispersive spectroscopy...
-
Information and communication technologies versus diffusion and substitution of financial innovations. The case of exchange-traded funds in Japan and South Korea
PublicationThe substitution between financial innovations, exchange-traded funds (ETFs), and stock index derivatives (i.e. index financial instruments) is one of the relatively understudied topics of the financial sciences. The current study aims to verify empirically the diffusion and substitution of ETFs in the market for index financial instruments. It presents in-depth analysis of the development of index financial instruments traded...
-
Exchange-traded products in Germany: development and substitution of exchange-traded funds, exchange-traded commodities and exchange-traded notes.
PublicationResearch background: Exchange-traded products (ETPs) are one of the most rapidly growing categories of financial products. Their fast development has been boosted by innovative features. Three main categories of ETPs are exchange-traded funds (ETFs), exchange-traded commodities (ETCs) and exchange-traded notes (ETNs). ETCs and ETNs remain least known, even though their number on some stock exchanges is high. In Europe, Germany...
-
Solid-Contact Ion-Selective Electrodes with Highly Selective Thioamide Derivatives of p-tert-Butylcalix[4]arene for the Determination of Lead(II) in Environmental Samples
Publication -
Selecting Features with SVM
PublicationA common problem with feature selection is to establish how many features should be retained at least so that important information is not lost. We describe a method for choosing this number that makes use of Support Vector Machines. The method is based on controlling an angle by which the decision hyperplane is tilt due to feature selection. Experiments were performed on three text datasets generated from a Wikipedia dump. Amount...
-
3-Substituted phenylalanines as selective AMPA- and kainate receptor ligands
Publication -
Selective Harmonic Elimination PWM For a Cascaded Multi-level Inverter
PublicationThis paper deals with the selective harmonic elimination pulse width modulation (SHE-PWM) technique. This technique is used for the elimination of selected dominant low order harmonics in the multi-level inverter output voltage. The presence of these harmonics is the essential drawback of such kind of inverters; especially when it is used for the control of different AC drivers. The SHE-PWM is based...
-
Kinetic Description of the Membrane–Solution Interface for Ion-Selective Electrodes
Publication -
Selective Protection for All-Optical Physical Impairment Constrained Routing
PublicationW przypadku sieci optycznych, zauważalna jest obecnie tendencja dążenia do transmisji całowicie optycznej (tz. bez konwersji O/E/O w węzłach tranzytowych). Jednakże w niedalekiej przyszłości, z uwagi na techniczne ograniczenia, niemożliwa będzie obsługa całości ruchu wyłącznie w dziedzinie optycznej. Operatorzy będą więc zainteresowani oferowaniem rozwiązań przejściowych implikujących przełączanie w dziedzinie optycznej jedynie...
-
Human Obesity Is Characterized by a Selective Potentiation of Central Chemoreflex Sensitivity
Publication -
Selective Potentiation of Peripheral Chemoreflex Sensitivity in Obstructive Sleep Apnea
Publication -
Selective jamming of OFDM transmission in NB-IoT radio interface
PublicationThe paper presents the concept of smart jamming, which involves selective interference aimed at critical components of the OFDM signal. Research verifying the feasibility of this type of electronic attack are described. A realized testbed for jamming real NB-IoT signals in a downlink is presented. The test results demonstrate the feasibility of realizing selective jamming and its greater effectiveness compared to barrage interference.
-
Selective monitoring of noise emitted by vehicles involved in road traffic
PublicationAn acoustic intensity probe was developed measures the sound intensity in three orthogonal directions, making possible to calculate the azimuth and elevation angles, describing the sound source position. The acoustic sensor is made in the form of a cube with a side of 10 mm, on the inner surfaces of which the digital MEMS microphones are mounted. The algorithm works in two stages. The first stage is based on the analysis of sound...
-
Wideband Highly-Selective Bandpass Filtering Branch-Line Coupler
PublicationThis paper presents a novel design of a wideband highly-selective bandpass filtering branch-line coupler (FBLC). By integrating a coupled microstrip line, and an open-ended stub at each port of a single-section BLC, bandpass filtering characteristics with excellent selectivity and broad operating bandwidth have been achieved. The proposed circuit has been verified through EM simulations and physical measurements of the fabricated...
-
Selective harvesting of regional digital libraries and national metadata aggregators
Publication -
Molecular Umbrellas Modulate the Selective Toxicity of Polyene Macrolide Antifungals
PublicationAntifungal polyene macrolide antibiotics Amphotericin B (AmB) and Nystatin (NYS) were conjugated through the ω-amino acid linkers with diwalled “molecular umbrellas” composed of spermidine-linked deoxycholic or cholic acids. The presence of “umbrella” substituents modulated biological properties of the antibiotics, especially their selective toxicity. Some of the AmB-umbrella conjugates demonstrated antifungal in vitro activity...
-
Optimization of purification and selective burning of single-wall carbon nanotubes
Publication -
Selective Laser Melting of Ti Alloy for Manufacturing The Prosthetic Elements
PublicationThe selective laser melting (SLM) is the additive manufacturing method of custom-designed parts. The used materials and the applications are various, including medicine. The titanium and its alloys are materials for which the dimensional quality, surface smoothness and no or extremely low porosity are difficult to reach. In this paper, the successful attempt to obtain by SLM the individually designed prosthetic bridges is described....
-
Ionophores in polymeric membranes for selective ion recognition; impedance studies
PublicationBadania impedancyjne membran zawierających jonofory selektywne na kation Na+ (L1) i Cs+(L2) wykazały, ze stala dielektryczna materiału membrany zależy od typu uzytego plastyfikatora i zmienia się w zakresie od 28 do 60. Rezystancja membran zawierających ligand L1 i L2 wynosi 0.15 -1.4 Mohm w zależności od stężenia elektrolitu zewnnetrznego. Testowona dwa typy elektrod jonoselektywnych: elektrody typu ASS z polimerem przewodzącym...
-
TOTAL CROSS SECTIONS FOR ELECTRON SCATTERING FROM SELECTED HYDROCARBONS: THE SUBSTITUTIONAL AND ADDITIVITY EFFECTS
PublicationTotal cross sections (TCS) for electron scattering from selected alkyne molecules, ethylene and its derivatives are compared. All cross sections have been measured in a wide energy range, from about 1 eV up to 370 eV, with the same electrostatic electron spectrometer. The substitutional and additivity effects are indicated and discussed.
-
Salicylaldimine-based receptor as a material for iron(III) selective optical sensing
Publicationα,α-Bis(salicylimino)-m-xylene (L) was prepared using both conventional and microwave-assisted procedure. The compound exhibits ability to colorimetric recognition of iron(III) ions in aqueous environment, what is shown by significant color change from yellow to purple. In DMSO : water (9:1 v/v) solvent system receptor creates with iron(III) cations complexes of 2:1 stoichiometry (L:Fe3+) with stability constant (log K) 7.54±0.21....
-
Discovery of the First Highly Selective Antagonist of the GluK3 Kainate Receptor Subtype
Publication -
Chinifur, a Selective Inhibitor and "Subversive Substrate" for Trypanosoma congolense Trypanothione Reductase
Publication -
Standard and Fast Selective Catalytic Reduction of NO with NH3on Zeolites Fe-BEA
Publication -
Computer-aided design and selective laser melting of porous biomimetic materials
Publication -
Porous Selective Laser Melted Ti and Ti6Al4V Materials for Medical Applications
Publication -
Multiaxial fatigue behaviour of maraging steel produced by selective laser melting
Publication -
Comparison of Vacuum Sintered and Selective Laser Melted Steel AISI 316L
Publication -
Design of selective substrates of proteinase 3 using combinatorial chemistry methods
Publication -
Studies on the separation of some transition metals using trialkylimidazole as selective extractant
Publication -
Pyrrole bearing diazocrowns: Selective chromoionophores for lead(II) optical sensing
PublicationDiazocrowns of 18-, 21- and 23-membered rings with pyrrole residue as a part of macrocycle were for the first time used as chromoionophores in lead(II) selective optodes. Sensing properties of optodes depend on the type of macrocycle, namely its size and the type of linker: oligoether or hydrocarbon chain. The best results were obtained for optode bearing 18-membered crown with oligoether linker showing linear response range of...
-
Surface engineering of graphene oxide membranes for selective separation of perfluorooctanoic acids
PublicationPerfluoroalkyl compounds (PFCs) are environmental toxicants and their widespread detection and accumulation in the environment can be detrimental to the ecosystem. In this study, surface charge of GO membranes was engineered to enhance selectivity of graphene oxide (GO) membranes and for the removal of perfluorooctanoic acid (PFOA ∼400 Da) in real concentration ranges in wastewater streams. The structure and physicochemical properties...
-
Reduced diameter distribution of single-wall carbon nanotubes by selective oxidation
Publication -
Effect of Cobalt on the Activity of CuO/CeO2 Catalyst for the Selective Oxidation of CO
Publication -
IT Project Manager Selection Review
Publication -
Selection of pointing device for elders
PublicationW artykule przedstawiono metodykę i sposób akwizycji oraz analizy danych dla doboru optymalnego urządzenia wskazującego, dostosowanego do osób starszych. Przedstawiono wyniki próbnych testów na dwóch grupach - docelowej i referencyjnej oraz skomentowano wyniki.
-
Clonal selection in discrete optimization
PublicationW rozprawie zajmujemy się efektywnymi metodami przybliżonego rozwiązywania problemów optymalizacji dyskretnej, a w szczególności algorytmami opartymi na metodzie selekcji klonalnej (SK), należącymi do kategorii sztucznych systemów immunologicznych. Techniki optymalizacji to znaczące pole badań w informatyce, a niektóre ze starszych technik, takie jak algorytmy genetyczne, symulowane wyżarzanie czy przeszukiwanie tabu, stały się...
-
Selection of descriptive geometry textbooks
PublicationW artykule przedstawiono koncepcję badania podręczników do geometrii wykreślnej bazującą na psycholingwistycznej teorii komunikatu. Zaprezentowane podejście umożliwia analizę podręczników na sześciu poziomach odnoszących się do głównych funkcji komunikacji międzyludzkiej. W artykule skupiono się na postrzeganiu językowej funkcji podręczników geometrii wykreślnej i w tym zakresie stwierdzono wiele cech zbieżnych.
-
A derivatisation agent selection guide
PublicationThe development of new tools for providing high quality information in a cost-effective and expeditious way is one of the main aims of analytical chemistry. Remarkably, the introduc- tion of the 12 principles of green chemistry paved the way forward for the development of analytical methodologies that are, ideally, inherently safe for the operator and the environ- ment, with the least possible consumption of energy and chemicals,...
-
Charge distribution and magnetic interactions in PrBa2Cu3O7 with substitutional defects and oxygen disorder: the ab initio approach
PublicationW artykule zaprezentowano rezultaty kwantowomechanicznych obliczeń ''ab initio: struktury elektronowej układu PrBa2Cu3O7 zawierającego defekty substytucyjne (Pr_Ba) w podsieci barowo-tlenowej oraz wykazującego zaburzoną stechiometrię tlenową (O5). Badane defekty są odpowiedzialne za redystrybucję ładunku w układzie. Defekty Pr_Ba generują silnie zlokalizowane momenty magnetyczne, które oddziałują głównie na płaszczyzny miedziowo-tlenowe.
-
Synthesis and application of tetrazole di and triamide derivatives in ion-selective membrane electrodes
PublicationA number of tetrazole diamides and triamides have been synthesized and applied as ion carries in ion-selective membrane electrodes. Their selectivity and sensitivity were studied towards alkali, alkaline earth, transition and heavy metal cations. it was found that membranes doped with 3 and 2-nitrophenyl octyl ether exhibit an almost theoretial Nernstian response for NH+ over relatively wide concentration range. Elestrodes with...
-
Prosthetic Elements Made of the Ti-13Zr-13Nb Alloy by Selective Laser Melting
PublicationThe fabrication of the prosthetic foundations and bridges from the Ti-13Zr-13Nb alloy is described. The process was started from CAD/CAM design of 3D models of the foundations based on scanning of patient`s mouth. Next, 3D models were transformed into *.stl files for the manufacturing stage and then the manufacturing process by means of the selective laser melting with the SLM Realizer 100 equipment was made. The intrinsic structure...
-
Potential Aluminium(III)- and Gallium(III)-selective Optical Sensors Based on Porphyrazines
Publication -
Fluorescent Molecular Cages with Sucrose and Cyclotriveratrylene Units for the Selective Recognition of Choline and Acetylcholine
Publication -
Modeling of TiO2-Based Electron-Selective Contacts for Crystalline Silicon Solar Cells
Publication -
Poly(3-octylthiophene) as solid contact for ion-selective electrodes: contradictions and possibilities
Publication -
In-Tube Molecularly Imprinted Polymer Solid-Phase Microextraction for the Selective Determination of Propranolol
Publication