Filters
total: 176
filtered: 160
Search results for: MW-PACVD
-
Neural Modelling of Steam Turbine Control Stage
PublicationThe paper describes possibility of steam turbine control stage neural model creation. It is of great importance because wider application of green energy causes severe conditions for control of energy generation systems operation Results of chosen steam turbine of 200 MW power measurements are applied as an example showing way of neural model creation. They serve as training and testing data of such neural model. Relatively simple...
-
Induced-fit binding of laccase to gold and carbon electrodes for the biological fuel cell applications
PublicationAnalogues of laccase natural substrates (syringic, veratric, ferulic, vanillic, isovanillic, 3,5-dimethoxybenzoic aldehydes) were employed to bind and orient laccase molecules in a way which facilitates adsorption of the catalyst molecules and their electrical connection with the conductive support. Laccase was bound efficiently to these substrates both on gold and carbon electrodes forming, respectively, 2D and 3D films sensitive...
-
Comparison analysis of selected nuclear power plants supplied with helium from high-temperature gas-cooled reactor
PublicationThe article presents results of efficiency calculations for two 560 MW nuclear cycles with high-temperature gas-cooled reactor (HTGR). An assumption was made that systems of this type can be used in so-called marine nuclear power plants. The first analysed system is the nuclear steam power plant. For the steam cycle, the efficiency calculations were performed with the code DIAGAR, which is dedicated for analysing this type of systems....
-
Electricity generation from rapeseed straw hydrolysates using microbial fuel cells
PublicationRapeseed straw is an attractive fuel material for microbial fuel cells (MFCs) due to its high content of carbohydrates (more than 60% carbohydrates). This study has demonstrated that reducing sugars can be efficiently extracted from raw rapeseed straw by combination of hydrothermal pretreatment and enzymatic hydrolysis followed by utilization as a fuel in two-chamber MFCs for electrical power generation. The most efficient method...
-
Produkcja energii elektrycznej w ujęciu ekonomicznym
PublicationW pracy przedstawiono podstawowe zależności dotyczące przeprowadzania analizy techniczno - ekonomicznej związanych z projektami inwestycyjnymi. Ukazano układ kombinowany silnik o zapłonie samoczynnym – turbina parowa, którego zadaniem jest dzięki posadowieniu na platformie pływającej produkcja energii elektrycznej w tzw. systemie rozproszonym. Składa się on z silnika spalinowego tłokowego i skojarzonym z nim układem turbiny parowej,...
-
Femtosecond Er-doped fiber laser source tunable from 872 to 1075 nm for two-photon vision studies in humans
PublicationWe report the development of a widely-tunable femtosecond fiber laser system and its application for two-photon vision studies. The source is based on an Er-doped fiber laser with spectral shift up to 2150 nm, followed by a second harmonic generation module to generate a frequency-doubled beam tunable from 872 to 1075 nm. The source delivers sub-230 fs pulses with nearly-constant duration over the entire tuning range, with output...
-
Nanocrystalline diamond sheets as protective coatings for fiber-optic measurement head
PublicationFiber-optic sensors find numerous applications in science and industry, but their full potential is limited because of the risk of damaging the measurement head, in particular, due to the vulnerability of unprotected tips of the fiber to mechanical damage and aggressive chemical agents. In this paper, we report the first use of a new nanocrystalline diamond structure in a fiber-optic measurement head as a protective coating of...
-
Model fizykalny czy neuronowy? - Narzędzia do predykcji mocy wytwarzanej przez elektrownie wiatrowe
PublicationUstawowy obowiązek prognozowania mocy dotyczy właścicieli elektrowni wiatrowych o mocy znamionowej powyżej 50 MW. Ze względu na coraz większą ilość przyłączonych elektrowni wiatrowych do krajowej sieci elektroenergetycznej, zapis ten może ulec zmianie, obejmując źródła wiatrowe mniejszej mocy. Obecnie największa pojedyncza turbina wiatrowa w Polsce ma generator o mocy 3MW, natomiast największy zespół elektrowni wiatrowych (farma...
-
Analiza czynników wpływających na ekonomiczną efektywność elektrowni jądrowej
PublicationW artykule omówiono podstawowe czynniki, które mają wpływ na opłacalność elektrowni jądrowej. Jej efektywność ekonomiczną badano za pomocą wskaźników w postaci zaktualizowanej wartości netto inwestycji (NPV) i uśrednionego jednostkowego kosztu energii elektrycznej (LCOE). Obliczono także jednostkowy koszt wytwarzania energii elektrycznej w trakcie spłaty zobowiązań kredytowych (COE1) i po okresie spłaty (COE2). Przeprowadzono analizę...
-
Application of BDD thin film electrode for electrochemical decomposition of heterogeneous aromatic compounds
PublicationThe aim of the presented study is to investigate the applicability of electrochemical oxidation of aromatic compounds containing heteroatoms, e.g. waste from production of pesticides or pharmaceutics, at a borondoped diamond (BDD) electrode. The BDD electrodes were synthesized by microwave plasma enhanced chemical vapour deposition (MW PE CVD). Investigation of the electrode surface by optical microscopy and scanning electron microscopy...
-
SrCe0.9In0.1O3-δ-based reversible symmetrical Protonic Ceramic Cell
PublicationIn-doped SrCe0.9In0.1O3-δ (SCI) perovskite-type oxide is utilized as the solid electrolyte, as well as a component, together with SrFe0.75Mo0.25O3-δ (SFM) compound, in the composite-type electrodes to construct symmetrical Protonic Ceramic Fuel Cells (PCFC). With good mutual stability of SCI and SFM at high temperatures in water vapor-containing reducing and oxidizing conditions, as well as sufficient ionic conductivity with high...
-
Application of Thermo-chemical Technologies for Conversion of Associated Gas in Diesel-Gas Turbine Installations for Oil and Gas Floating Units
PublicationThe paper considers the issue of thermo-chemical recovery of engine’s waste heat and its further use for steam conversion of the associated gas for oil and gas floating units. The characteristics of the associated gas are presented, and problems of its application in dual-fuel medium-speed internal combustion engines are discussed. Various variants of combined diesel-gas turbine power plant with thermo-chemical heat recovery are...
-
INVESTIGATION OF THE CHARACTERISTICS OF A LOWEMISSION GAS TURBINE COMBUSTION CHAMBER OPERATING ON A MIXTURE OF NATURAL GAS AND HYDROGEN
PublicationT his article is devoted to the investigation of the characteristics of a low-emission gas turbine combustion chamber, which can be used in Floating Production, Storage and Offloading (FPSO) vessels and operates on a mixture of natural gas and hydrogen. A new approach is proposed for modelling the processes of burning out a mixture of natural gas with hydrogen under preliminary mixing conditions in gaseous fuel with an oxidizer...
-
On the possible increasing of efficiency of ship power plant with the system combined of marine diesel engine, gas turbine and steam turbine in case of main engine cooperation with the gas turbine fed in parallel and the steam turbine
PublicationW pracy przedstawiono koncepcję układu kombinowanego okrętowego dużej mocy złożonego z wiodącego silnika głównego spalinowego silnika tłokowego i skojarzonych z nim turbiny gazowej mocy i układu turbiny parowej, wykorzystujących energię zawartą w spalinach wylotowych głównego silnika spalinowego. Rozpatrzono wariant układu kombinowanego, w którym główny jest silnik tłokowy skojarzony z turbiną gazową mocy i układem turbiny parowej,...
-
Possibility to use engine compression ignition engines in floating power plants marine
PublicationCompression-ignition engines used in ship technology as main propulsion engines are large units reaching even to 50-60 MW. The engines can be used in power industry for electricity generation in a simple or combined steam turbine system in combined heat and power plants. The leading engine in such an arrangement is an internal-combustion piston engine. The main propulsion engines are used in large piston internal-combustion engines...
-
Feasibility of combined diesel engine - steam turbine in power station operating in the maritime
PublicationCompression-ignition engines used in ship technology as main propulsion engines are large units reaching even to 50-60 MW. Currently, the efficiency of such engines amounts to 45-50%. With such a large power unit, exhaust gases leaving the engine contain very large quantities of heat available for further treatment. Exhaust gases from the piston engine contain about 25% of the heat supplied to the engine in the fuel. Using the...
-
Równowagowy przepływ pary mokrej w części niskoprężnej turbiny parowej
PublicationW części niskoprężnej (NP) kondensacyjnej turbiny parowej przedostatni stopień ( zwany stopniem Baumanna) stwarza możliwość zwiększenia mocy wyjściowej turbiny, bez zwiększenia długości łopatek ostatniego stopnia. Stopień Baumanna pracuje w obszarze, w którym zachodzi zjawisko tzw. spontanicznej kondensacji, która jest nierównowagowym przejściem fazowym. Początek obszaru występowania pary mokrej jest związany z położeniem tzw....
-
Reaktory jądrowe małej i średniej mocy
PublicationOstatnie lata przyniosły wzrost zainteresowaniareaktorami jądrowymi małej i średniej mocy (SMR - ang.Small and Medium Reactors), których moce nie przekraczają700 MW, jako rozwiązania alternatywnego dladużych skomercjalizowanych bloków jądrowych. Obecnierozwijane reaktory małych i średnich mocy mogą konkurowaćz dużymi reaktorami z uwagi na zalety w postaci:1) mniejszej konstrukcji pozwalającej na produkcjęelementów reaktora w nadzorowanych...
-
Thermal utilization of meat-and-bone meal using the rotary kiln pyrolyzer and the fluidized bed boiler – The performance of pilot-scale installation
PublicationThermal utilization of meat-and-bone meal (MBM) is subject to stringent regulations that are meant to provide elimination of any potential pathogens. Incineration as well as other possible routes for thermal conversion of MBM are still at the research state. The universal technology was developed that allows to combust various types of waste organic materials, including animal waste, municipal solid waste and sludge, mixed at any...
-
Game-based Sprint retrospectives: multiple action research
PublicationIn today’s fast-paced world of rapid technological change, software development teams need to constantly revise their work practices. Not surprisingly, regular reflection on how to become more effective is perceived as one of the most important principles of Agile Software Development. Nevertheless, running an effective and enjoyable retrospective meeting is still a challenge in real environments. As reported by several studies,...
-
Characteristics of La 0.8 Sr 0.2 Ga 0.8 Mg 0.2 O 3-δ -supported micro-tubular solid oxide fuel cells with LaCo 0.4 Ni 0.6-x Cu x O 3-δ cathodes
PublicationIn this study, micro-tubular solid oxide fuel cells (T-SOFCs) with extruded La0.8Sr0.2Ga0.8Mg0.2O3-δ (LSGM) electrolyte as the mechanical support and LaCo0.4Ni0.6O3-δ (LCNO) or LaCo0.4Ni0.4Cu0.2O3-δ (LCNCO) as cathodes were prepared and characterized. Partial substitution of Cu for the Ni-ion positions in the LCNO lattices was found to significantly enhance the densification and accelerate the grain growth. The porosity-corrected...
-
Wytwarzanie i charakterystyka cienkich warstw diamentowych na podłożach ze szkła kwarcowego, w szczególności na światłowodach włóknistych, dla zastosowań w sensorach optoelektronicznych
PublicationGłównym celem naukowym prac badawczych przeprowadzonych w rozprawie było wytwarzanie i modyfikacja funkcjonalności cienkich, przewodzących warstw diamentowych syntezowanych na podłożach optycznych. W ramach przeprowadzonych badań wytworzono szereg warstw diamentowych o specyficznych właściwościach optycznych i elektrycznych, mających na celu wykazanie możliwości wykorzystania takich struktur dla celów sensorycznych. Do poprawy...
-
Analiza kosztów wytwarzania energii elektrycznej w elektrowni jądrowej
PublicationW niniejszym referacie omówiono problematykę obliczania kosztów wytwarzania energii elektrycznej w elektrowni jądrowej. Posłużono się, znaną metodyką kalkulacji kosztów rocznych w elektroenergetyce oraz metodą uśrednionego jednostkowego kosztu energii elektrycznej (LCOGE). Podstawowymi czynnikami wpływającymi na poziom kosztów rocznych w elektrowni jądrowej są nakłady inwestycyjne, stopa dyskontowa oraz koszty eksploatacyjne stałe....
-
DESIGN ANALYSIS OF HYBRID GAS TURBINE - FUEL CELL POWER PLANT IN STATIONARY AND MARINE APPLICATIONS
PublicationThe paper concerns design analysis of a hybrid gas turbine power plant with a fuel cell (stack). The aim of this work was to find the most favorable variant of the medium capacity (approximately 50 MW) hybrid system. In the article, computational analysis of two variants of such a system was carried out. The analysis let to calculate capacity, efficiency of both variants and other parameters like flu gas temperature. The paper...
-
The Influent Effects of Flow Rate Profile on thePerformance of Microbial Fuel Cells Model
PublicationThe energy contained in wastewaters has been identified as a promising sustainableenergy resource that could be harvested by using microbial fuel cells (MFC). When dealing with realwastewaters, the MFCs should be able to manage high flow rates and flow rates fluctuations. In thiswork, the short-term effects of the influent flow rate variations on the performance of a microbialfuel cell has been studied. With this aim, the influent...
-
Hybrid geothermal-fossil power cycle analysis in a Polish setting with a focus on off-design performance and CO2 emissions reductions
PublicationGrowing demand for electricity due to economic development contributes to increased greenhouse gas production, especially CO2. However, emissions can be limited by enhancing the efficiency of primary energy conversion, such as integrating geothermal energy into coal-fired power plants. Therefore, this paper proposes replacing conventional feed-water heaters with geothermal preheaters to create a hybridized system. This study was...
-
Badania nad wykorzystaniem fotokatalizatorów WO3/TiO2 do degradacji wybranych zanieczyszczeń organicznych
PublicationW dysertacji skupiono się na: preparatyce fotokatalizatorów WO3/TiO2, weryfikacji efektywności działania kompozytów w kierunku fotokatalitycznego usuwania zanieczyszczeń oraz analizie wyników pod kątem zaprojektowania i skonstruowania fotoreaktora wyposażonego w sterowane źródło światła LED do fotokatalitycznej degradacji zanieczyszczeń. Fotokatalizatory otrzymano łącząc dwie metody preparatyki – zol-żel i hydrotermalną. Otrzymano...
-
Optical and electrical properties of ultrathin transparent nanocrystalline boron-doped diamond electrodes
PublicationThe optical properties of ultrathin (less than 100 nm) boron-doped nanocrystalline diamond (B-NCD) film were investigated in a wavelength range of 200 ÷ 20000 nm. The B-NCD refractive index showed values close to that of monocrystalline diamond (n = 2.45) in a broad wavelength range (450 ÷ 4000 nm). A transmittance up to 70% and the average film thickness of 70 nm were achieved. A special cone-shaped shim was used in the deposition...
-
Pomiar i prognozowanie przemieszczeń elektrowni wiatrowych metodami geodezyjnymi
PublicationW pracy analizowano pomiar przemieszczeń dwóch elektrowni wiatrowych o mocy 2 MW i wysokości wieży 78 m, wykonanych jako konstrukcja rurowa ze stali. Elektrownie posadowione zostały na fundamencie żelbetowym, bezpośrednim o wymiarach 16 m x 16 m x 2 m. Badane elektrownie zlokalizowane są w rejonie Wybrzeża Gdańskiego. Pomiary przemieszczeń wykonywane były metodami geodezyjnymi w warunkach budowy i sześciu lat ich eksploatacji....
-
Impact of steel grade on a ship colliding with an offshore wind turbine monopile supporting structure
PublicationOffshore wind power is experiencing rapid development around the world. The number of installations and their size is growing. Thousands of monopile support structures with diameters of 10 m and weights of 2000 tons will be installed in the coming years. Offshore wind power installations, often located close to the shore and shipping routes, pose a new challenge to ship safety. The study analyses the damages from an accidental...
-
Thermodynamic and economic analysis of nuclear power unit operating in partial cogeneration mode to produce electricity and district heat
PublicationThis paper presents the methodology of techno-economic analysis for a nuclear unit operating in partial cogeneration mode and its application for the case study: a nuclear power plant planned in Poland. The research objectives were: to propose EPR, AP1000 and ESBWR nuclear condensing-extraction turbine systems modifications required for operation in cogeneration, to determine optimal heat production and heat transport line (HTL)...
-
Fully Isohexide-Based Polyesters: Synthesis, Characterization, and Structure-Properties Relations
PublicationHere we present a novel series of biobasedpolyesters solely based on renewable isohexide building blocks,synthesized via melt polymerization. The recently developedisoidide dicarboxylic acid (IIDCA) was polymerized with rigidrenewable diols such as isosorbide (IS), isomannide (IM),isoidide (II), and the novel 2,5-methylene-extended isoididedimethanol (IIDML). Both IIDCA and IIDML weredeveloped to increase the reactivity of the...
-
High Frequency Harmonics Emission in Smart Grids
PublicationPulse-width modulated rectifiers are nowadays commonly used for AC to DC power conversion. PWM rectification technology is very effective and allows for bidirectional power flow with the possibility of power factor improvement and low-order harmonic emission limitation. Unfortunately, employed PWM boost topology results with generation of input current harmonic distortions in a frequency range tightly correlated to modulation frequency....
-
Low Frequency Conducted Emissions of Grid Connected Static Converters
PublicationPulse-width modulated rectifiers are nowadays commonly used for AC to DC power conversion. PWM rectification technology is very effective and allows for bidirectional power flow with the possibility of power factor improvement and low-order harmonic emission limitation. Unfortunately, employed PWM boost topology results with generation of input current harmonic distortions in a frequency range tightly correlated to modulation frequency....
-
Technical and economic conditions of supplying residential consumers with heat from nuclear power plant
PublicationThe reduction of CO2 emission requires technological shift towards carbon-free options. Cogeneration of electricity and heat based on coal and natural gas will experience generation cost increase, if the costs of emissions are imposed on the plant operators. Therefore, nuclear and renewable options should be considered. In this paper, we present the concept of electricity and heat supply system with nuclear condensing turbine adapted...
-
Assessment of the Current Potential of Hydropower for Water Damming in Poland in the Context of Energy Transformation
PublicationThe present paper indicates that hydropower, including small hydropower plants (SHPs), may play a very important role in Poland’s energy transformation in the near future. The development of SHPs may also increase water resources in the steppe Poland. Additionally, the aim of the present research is to conduct the PEST analysis of SHPs in Poland, taking into account the SHP potential. For the first time, maps showing the power...
-
Hybrid Multi-Criteria Method of Analyzing the Location of Distributed Renewable Energy Sources
PublicationThis paper presents the development and the application of a hybrid multi-criteria method, the combination of the Analytic Hierarchy Process (AHP), and numerical taxonomy (NT),to support the decision making on the location of distributed renewable energy sources meetingvarious types of assessment criteria. Finding criteria weights, using the AHP method, eliminates thedisadvantage of NT—which, in current form, is defined by its...
-
The influence of crude glycerol and castor oil-based polyol on the structure and performance of rigid polyurethane-polyisocyanurate foams
PublicationIn this work, biopolyol obtained from two types of industrial crops’ processing products: crude glycerol and castor oil was used for preparation or rigid polyurethane-polyisocyanurate foams. Bio-based polyol was obtained via crude glycerol polymerization and further condensation of resulting polyglycerol with castor oil. Rigid polyurethane-polyisocyanurate foams were prepared at partial substitution (0–70 wt.%) of petrochemical...
-
Enhanced capacitance of composite TiO2 nanotube / boron-doped diamond electrodes studied by impedance spectroscopy
PublicationWe report on the novel composite nanostructures based on boron-doped diamond thin film grown on top of TiO2 nanotubes. The nanostructures made of BDD-modified titania nanotubes showed an increase in activity and performance when used as electrodes in electrochemical environments. The BDD thin films (~200-500 nm) were deposited using microwave plasma assisted chemical vapor deposition (MW PA CVD) onto anodically fabricated TiO2...
-
Microwave radiation in the synthesis of urethane prepolymers
PublicationThis paper describes the use of microwave radiation in the synthesis of urethane prepolymers in bulk (without solvent). The prepolymers were synthesized using 1,6-hexamethylene diisocyanate (HDI) and poly (ε-caprolactone) diol (PCL) at a molar ratio of 4:1. The reaction was carried out without a catalyst in the reactor with a conventional heating system (oil bath) or in the microwave reactor (MW Reactor NOVA 09) at temperatures...
-
Opto-Electrochemical Sensing Device Based on Long-Period Grating Coated with Boron-Doped Diamond Thin Film
PublicationThe fabrication process of thin boron-doped nanocrystalline diamond (B-NCD) microelectrodes on fused silica single mode optical fiber cladding has been investigated. The B-NCD films were deposited on the fibers using Microwave Plasma Assisted Chemical Vapor Deposition (MW PA CVD) at glass substrate temperature of 475 ºC. We have obtained homogenous, continuous and polycrystalline surface morphology with high sp3 content in B-NCD...
-
Diamond-based protective layer for optical biosensors
PublicationOptical biosensors have become a powerful alternative to the conventional ways of measurement owing to their great properties, such as high sensitivity, high dynamic range, cost effectiveness and small size. Choice of an optical biosensor's materials is an important factor and impacts the quality of the obtained spectra. Examined biological objects are placed on a cover layer which may react with samples in a chemical, biological...
-
Nanocrystalline diamond microelectrode on fused silica optical fibers for electrochemical and optical sensing
PublicationFabrication process of thin boron-doped nanocrystalline diamond (B-NCD) microelectrode on fused silica single mode optical fiber has been investigated. The B-NCD films were deposited on the fibers using Microwave Plasma Assisted Chemical Vapor Deposition (MW PA CVD) at glass substrate temperature of 475 ºC. We have obtained homogenous, continuous and polycrystalline surface morphology with the mean grain size in the range of 100-250...
-
Advanced Turbine Cycles with Organic Media
PublicationOrganic Rankine Cycle (ORC) power plants have become very popular and have found their applications in systems with renewable sources of energy. So far their overall efficiencies are not very impressive and only for the upper temperature of about 300 °C do they exceed 20%. A drawback of these cycles is the limitation of the cycle upper temperature due to the heat exchanger technology and the materials used. However, it is possible...
-
Conditions for increasing the recognition of degradation in thermal-flow diagnostics, taking into account environmental legal aspects
PublicationThe ever-increasing demand for electricity and the need for conventional sources to cooperate with renewable ones generates the need to increase the efficiency and safety of the generation sources. Therefore, it is necessary to find a way to operate existing facilities more efficiently with full detection of emerging faults. These are the requirements of Polish, European and International law, which demands that energy facilities...
-
Using LSTM networks to predict engine condition on large scale data processing framework
PublicationAs the Internet of Things technology is developing rapidly, companies have an ability to observe the health of engine components and constructed systems through collecting signals from sensors. According to output of IoT sensors, companies can build systems to predict the conditions of components. Practically the components are required to be maintained or replaced before the end of life in performing their assigned task. Predicting...
-
Tuning Electrochemical Performance by Microstructural Optimization of the Nanocrystalline Functional Oxygen Electrode Layer for Solid Oxide Cells
PublicationFurther development of solid oxide fuel cell (SOFC) oxygen electrodes can be achieved through improvements in oxygen electrode design by microstructure miniaturisation alongside nanomaterials implementation. In this work, improved electrochemical performance of an La0.6Sr0.4Co0.2Fe0.8O3-d (LSCF) cathode was achieved by the controlled modification of the La0.6Sr0.4CoO3-d (LSC) nanocrystalline interlayer introduced between a porous...
-
Influence of the boron doping level on the electrochemical oxidation of the azo dyes at Si/BDD thin film electrodes
PublicationIn this study the efficiency of electrochemical oxidation of aromatic pollutants, such as reactive dyes, at boron-doped diamond on silicon (Si/BDD) electrodes was investigated. The level of [B]/[C] ratio which is effective for the degradation and mineralization of selected aromatic pollutants, and the impact of [B]/[C] ratio on the crystalline structure, layer conductivity and relative sp3/sp2 coefficient of a BDD electrode were...
-
Improved surface coverage of an optical fibre with nanocrystalline diamond by the application of dip-coating seeding
PublicationGrowth processes of diamond thin films on the fused silica optical fibres (10 cm in length) were investigated at various temperatures. Fused silica pre-treatment by dip-coating in a dispersion consisting of detonation nanodiamond (DND) in dimethyl sulfoxide (DMSO) with polyvinyl alcohol (PVA) was applied. Nanocrystalline diamond (NCD) films were deposited on the fibres using the microwave plasma assisted chemical vapour deposition...
-
CO2 capture using steam ejector condenser under electro hydrodynamic actuator with non-condensable gas and cyclone separator: A numerical study
PublicationThe concept for condensation of steam and CO2 separation in a negative CO2 emission gas power plant involves the utilization of a steam ejector condenser (SEC) for direct-contact condensation of vapor with inert gas (CO2) on a spray of subcooled liquid, integrated with a separator to produce pure CO2. Due to the increasing diffusion resistance and reduced convective heat transfer between the steam and subcooled water phases...