displaying 1000 best results Help
Search results for: TEHD CALCULATION
-
Nitrogen sorption isotherm for V2CTx
Open Research DataData of points for nitrogen sorption isotherm for sample V2CTx (only sorption branch). The V2CTx was prepared via selective etching of aluminium from MAX matrice V2AlC using 50% HF for 96 h at room temperature.
-
Diffuse large B-cell lymphoma, NOS - Male, 55 - Tissue image [5040730020282601]
Open Research DataThis is the histopathological image of LYMPH NODES tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
Comparison analysis of selected nuclear power plants supplied with helium from high-temperature gas-cooled reactor
PublicationThe article presents results of efficiency calculations for two 560 MW nuclear cycles with high-temperature gas-cooled reactor (HTGR). An assumption was made that systems of this type can be used in so-called marine nuclear power plants. The first analysed system is the nuclear steam power plant. For the steam cycle, the efficiency calculations were performed with the code DIAGAR, which is dedicated for analysing this type of systems....
-
Euilibrium composition of CH4-CO2-CO-H2-H2O-C system under various compositions syngas methanation
Open Research DataThe equilibrium compositions of CH4, CO2, CO, H2, H2O and C under the methanation reaction of various syngas mixtures (different CO/H2 ratio) were supplied with this dataset
-
Euilibrium composition of CH4-CO2-CO-H2-H2O system for CO2/H2/H2O methanation
Open Research DataThe equilibrium compositions of CH4, CO2, CO, H2, H2O without C under the methanation reaction of 1:2 CO:H2 syngas mixtures were supplied with this dataset
-
Comparative Evaluation of Multicoil Inductive Power Transfer Approaches Based on Z-source Network
PublicationThis paper describes comparative evaluation between wireless power transfer topologies with utilization of Z-source network. Paper describes components calculation method. List of open-loop, close-loop simulations were conducted to compare both topologies. Spectrum of signals is also researched.
-
Determination of equivalent axle load factors with the use of strain energy of distortion
PublicationThe paper proposes a new method for calculation of equivalent axle load factors based on the analysis of strain energy of distortion induced in road pavements by traffic loads. The main advantage of the method is the more accurate calculation of the effects of multiple axles and super single versus dual tyres. The methodconsiders the location of critical points, at which strain energy of distortion reaches extreme values. When...
-
Analyzing the Geometry of the Turnouts and Their Adjustment Basing on the Tacheometer Measurements
PublicationThe article presents the results of tacheometric measurements of a station throat, as well as the method of data preparation and analysis. The calculations covered the verification of the geometry and the location of railway turnouts and crossings. The analyses were performed for the selected parameters of the turnout geometry, including their lengths and track gauge in main sections. In addition, the data were analyzed to confirm...
-
Proton transfer reactions for ionized water clusters
PublicationCalculations of formation energies of the ionized water clusters and energies of reactions between small (including less than eight water molecules) neutral and positively ionized water clusters are presented. Moreover, we discuss some reaction paths between neutral and positively charged dimers, trimers and tetramers and proton transfer reactions (PTR) between cyclic clusters and H3O+ ions which can appear in beam experiments...
-
Programmable feedforward linearized CMOS OTA for fully differential continuous-time filter design
PublicationW artykule przedstawiono metodę linearyzacji wzmacniacza transkonduktancyjnego (OTA) CMOS z zastosowaniem sprzężenia w przód. Wzmacniacz zbudowany jest z użyciem prostych par różnicowych, wzmacniacza w pętli sprzężenia zwrotnego do samoregulacji transkonduktancji wzmacniaczy oraz liniowej rezystancji odniesienia (R). W wyniku uzyskano znaczną linaryzację charakterystyk przejściowych wzmacniacza OTA. Symulacje komputerowe SPICE...
-
Continuous wave sonar with hyperbolic frequency modulation keyed by pseudo-random sequence
PublicationA CW FM type sounding signal is used in the classical solution of silent sonar. While the signal provides a relatively simple implementation of digital signal processing, and ensures good detection conditions, unfortunately, in the presence of the Doppler effect, distance measurement results tend to be wrong. This is due to the fact that the received signal’s instantaneous frequency value is dependent both on the distance to the...
-
Quality Modeling in Grid and Volunteer-Computing Systems
PublicationA model of computational quality in large-scale computing systems was presented in the previous chapter of this book. This model describes three quality attributes: performance, reliability and energy efficiency. We assumed that all processes in the system are incessantly ready to perform calculations and that communication between the processes occurs immediately. These assumptions are not true for grid and volunteer computing...
-
NUMERICAL ANALYSIS OF SPECIES DIFFUSION AND METHANOL DECOMPOSITION IN THERMOCATALYTIC REACTOR BASED ON THE INTERMETALLIC PHASE OF Ni3Al FOR LOW REYNOLDS NUMBERS
PublicationNumerical modelling of hydrogen production by means of methanol decomposition in a thermocatalytic reactor using corrugated foil made of the Ni3Al intermetallic phase is shown in the paper. Experimental results of the flow analysis of mixtures containing helium and methanol in a thermocatalytic reactor with microchannels were used for the initial calibration of the CFD calculations (calculations based on the Computational Fluid...
-
A semi-empirical model for flow boiling heat transfer with account of the reduced pressure effect
PublicationIn the present study the attention was focused on the influence of reduced pressure on the predictions of heat transfer during flow boiling at the extensive range of pressures. The results of calculations were to test the sensitivity of the in-house flow boiling model with respect to the selection of the appropriate two-phase flow multiplier, which is one of the distinctive elements of that model. For this purpose a few two-phase...
-
Some Aspects of Designing Nozzle Segments of Axial Microturbines,
PublicationIn the paper a multi-stage micro-turbine with partial admission of all the stages is described in detail and the results of the numerical calculations and experimental investigations are presented, followed by an appropriate discussion and conclusions.
-
Precise Point Positioning Method Based on Wide-lane and Narrow-lane Phase Observations and Between Satellites Single Differencing
PublicationThe issue of using PPP method in position determination was formed in 1997. In most developed methods, ionospheric-free linear combination is used in order to eliminate the impact of the ionospheric delay. However, this approach does not provide the directly determination of the total value of the ambiguities, and the ambiguities for the individual signals. Therefore, in many publications methods of avoiding these deficiencies...
-
Efficient Method for the Concentration Determination of Fmoc Groups Incorporated in the Core-Shell Materials by Fmoc–Glycine
PublicationIn this paper, we described the synthesis procedure of TiO2@SiO2 core-shell modified with 3-(aminopropyl)trimethoxysilane (APTMS). The chemical attachment of Fmoc–glycine (Fmoc–Gly–OH) at the surface of the core-shell structure was performed to determine the amount of active amino groups on the basis of the amount of Fmoc group calculation. We characterized nanostructures using various methods: transmission electron microscope...
-
The concept of improving warehouse management in the X production company
PublicationThe article aims at the presentation of a concept referring to the improvement of warehouse management in the X production plant. The authors suggest two solutions: using storage racks at the picking process site and warehouse automation. Ultimately, the authors of the article present their basic calculation of the costs, indicating the increase in efficiency after the implementation of the discussed...
-
On Algorithm Details in Multibeam Seafloor Classification
PublicationRemote sensing of the seafloor constitutes an important topic in exploration, management, protection and other investigations of the marine environment. In the paper, a combined approach to seafloor characterisation is presented. It relies on calculation of several descriptors related to seabed type using three different types of multibeam sonar data obtained during seafloor sensing, viz.: 1) the grey-level sonar images (echograms)...
-
Numerical Study of the Impinging Jets Formed by an Injector with Different Nozzle Diameters
Open Research DataThe data set contains the simulation files related to the research paper “Numerical Study of the Impinging Jets Formed by an Injector with Different Nozzle Diameters”, https://doi.org/10.4271/2022-01-1080.
-
Euilibrium composition of CH4-CO2-CO-H2-H2O-C system under various compositions syngas methanation with 10% water vapour introduced
Open Research DataThe equilibrium compositions of CH4, CO2, CO, H2, H2O and C under the methanation reaction of various syngas mixtures (different CO/H2 ratio) were supplied with this dataset
-
Euilibrium composition of CH4-CO2-CO-H2-H2O-C system under various compositions syngas methanation with 30vol.% water vapour introduced
Open Research DataThe equilibrium compositions of CH4, CO2, CO, H2, H2O and C under the methanation reaction of various syngas mixtures (different CO/H2 ratio) were supplied with this dataset
-
POWER EFFICIENCY OF POWER PLANTS ON TRAILING SUCTION HOPPER DREDGERS
PublicationThis paper presents the notion of operational power efficiency and compares it with the classical definition of power efficiency. There are presented also calculation results of power efficiency for a selected suction hopper dredger and also influence of power system type of suction hopper dredger on magnitude of power efficiency of its power plant has been highlighted.
-
Monthly mean sea surface temperature (SST) of the Baltic Sea
Open Research DataMonthly mean sea surface temperature (SST) from 2001 to 2022 calculated from data from the SatBaltic System (https://satbaltyk.iopan.gda.pl/). The spatial resolution of the maps is 1 km. The calculation of monthly mean values at each pixel was based on four SST maps on each day of the month. The primary source of SST information was satellite data collected...
-
Expert assessment of arguments: a method and its experimental evaluation
PublicationArgument structures are commonly used to develop and present cases for safety, security and other properties. Such argument structures tend to grow excessively. To deal with this problem, appropriate methods of their assessment are required. Two objectives are of particular interest: (1) systematic and explicit assessment of the compelling power of an argument, and (2) communication of the result of such an assessment to relevant...
-
Prospects of Decreasing Power Losses in a Hydrostatic Thrust Bearing
PublicationIn numerous machines, axial load is carried by tilting pad thrust bearings known since the beginning of 20th century. These bearings are commonly bath lubricated, which is simple, does not require any additional pumps, and, due to this, such systems are highly reliable. In a contemporary technology, however, minimization of friction losses became an important goal of machinery improvement. Calculations based on elementary rules...
-
FE analysis of a coupled energetic-statistical size effect in plain concrete beams with varying material properties.
PublicationThe numerical FE investigations of a coupled energetic-statistical size effect in unnotched concrete beams of similar geometry under quasi-static three point bending were performed within elasto-plasticity with non-local softening. The stochastic FE analyses were carried out with three different beam sizes. Deterministic calculations were performed with the uniform distribution of a uniaxial tensile strength. In statistical calculations...
-
Verification of baffle factor for straight pipe flow
PublicationDuring the water disinfection devices designing, it is often assumed that the baffle factor for a straight pipe reactors is equal to one. It would be possible only for the plug flow, which is a simplified model of the flow and does not appear in real situations. The paper contains an equation which enables calculation of the real value of the baffle factor for the pipe flow.
-
Experimental Study of the Influence of Noise Level on the Uncertainty Value in a Measurement System Containing an Analog-to-Digital Converter
Open Research DataFor newly developed measuring systems it is easy to estimate type B uncertainties based on the technical data of the measuring modules applied. However, it is difficult to estimate A type un-certainties due to the unknown type and level of interferences infiltrating into the measuring sys-tem. This is a particularly important problem for measurements...
-
Ring thruster - a preliminary optimisation study
PublicationThe ring thruster is a new type of propeller, for which there is no experimental data to verify analytical design calculations. A significant feature of the ring thruster is the absence of a shaft. Propeller blades are mounted to the ring rotating inside the housing, which has the shape of a nozzle. For this reason the ring thruster is closest, with respect to both the construction and principle of operation, to the Kort nozzle...
-
Euilibrium composition of CH4-CO2-CO-H2-H2O-C system under various compositions syngas methanation with 20vol.% water vapour introduced
Open Research DataThe equilibrium compositions of CH4, CO2, CO, H2, H2O and C under the methanation reaction of various syngas mixtures (different CO/H2 ratio) were supplied with this dataset
-
Deep slot effect in the squirrel-cage induction motors with scalar (V/F) control
PublicationQualitative characteristics of the electrical drive considerably depend on identification accuracy of math model parameters. In particular, it is depend on detection accuracy of stator active resistance r1 that is used in calculation of flux linkages, rotary speed in sensorless control systems. Paper provides analysis of influence of stator deep slot effect to stator active resistance value
-
Analysis of EN 1993-1-6 guidelines about determining amplitudes of equivalent imperfections of steel cylindrical shells subjected to uniform external pressure
PublicationCivil engineering structures should be designed with reference to relevant standards. One of them is a Eurocode 3 standard EN 1993-1-6:2007: Design of steel structures Part 1-6: Strength and Stability of Shell Structures. According to this standard, the value of buckling load can be determined using different approaches: classical hand calculations (stress design) and geometrical and material non-linear analysis of an imperfect...
-
Design of a 3.3V four-quadrant analog CMOS multiplier
PublicationW pracy przedstawiono dwa czterokwadrantowe mnożniki analogowe CMOS pracujące przy napięciu zasilania 3.3V. Układy wykorzystują tranzystory MOS pracujące zarówno w zakresie nasycenia jak i w zakresie triodowym. Wyniki symulacji komputerowych pokazują, że współczynnik zawartości harmonicznych (THD) sygnału wyjściowego jest mniejszy niż 0.75% dla sygnału wejściowego o amplitudzie 1V o częstotliwości 10MHz. Pasmo 3dB układu wynosi...
-
Accuracy Investigations of Turbine Blading Neural Models Applied to Thermal and Flow Diagnostics
PublicationPossibility of replacing computional fluid dynamics simulations by a neural model for fluid flow and thermal diagnostics of steam turbines is investigated. Results of calculations of velocity magnitude of steam for 3D model of the stator of steam turbine is presented.
-
Proposed method for estimating the costs of safety barrier life cycle
PublicationToday barrier types are frequently selected for their price with little regard for the total costs the structure will incur over its lifetime. One of the basic tools designed to manage road infrastructure is the life cycle cost method (LCC, Life cycle cost). It sums up the costs to plan, design, build, operate (use and maintain) and decommission a road structure. Having developed dynamically at the turn of the century the method...
-
Hedging Strategies of Derivatives Instruments for Commodity Trading Entities
PublicationHedging as an outcome of risk management arises to account several questions. Mentioned aspect of size of the hedging is one of them. Latter questioning refers to whether producer of manufacturer are willing to secure entire exposure, when the hedging should start, now or later in the future, what is the vision on market like direction of market, time of interest, magnitude of exposure, what would be the preferred instruments of...
-
Support for argument structures review and assessment
PublicationArgument structures are commonly used to develop and present cases for safety, security and for other properties of systems. Such structures tend to grow excessively, which causes problems with their review and assessment. Two issues are of particular interest: (1) systematic and explicit assessment of the compelling power of an argument, and (2) communication of the result of such an assessment to relevant recipients. The paper...
-
Solid road environment and its hazards
PublicationAccidents that involve vehicles departing the road tend to have very high severity, as they often result in the vehicle hitting a permanent obstacle (which can be a ree, a pole, facility pillar, front wall of a culvert or a barrier). In recent years, this type of accident caused approx. 19% of all road deaths in Poland. A particularly high risk can be observed on roads located in northern and western...
-
Burst loss probability for the combination of extended offset time based service differentiation scheme and PPS in optical burst switching network
PublicationIn the paper analytical model for calculating burst loss probabilities for the combination of two service differentiation schemes for OBS network namely: extended offset time based scheme and PPS (Preemption Priority Schemes) is revised. Moreover authors introduce analytical model for calculating burst loss probabilities for an optical path when OBS network employs both service differentiation schemes and JET signaling. The comparison...
-
Service and Path Discovery Extensions for Self-forming IEEE 802.11s Wireless Mesh Systems
PublicationWith the rapid growth of the quantity and capabilities of end-user electronic devices, both stationary and mobile, they are employed in increasing number of applications. In this situation, wireless network technologies begin to play a crucial role as networks access technologies, as cable-based solutions tend to be of limited utility in case of easily portable or mobile devices. Resulting development of wireless technologies reached...
-
NUMERICAL SIMULATIONS OF GAP FLOW ABOVE ROTATING DISK
PublicationA rotating disk can be considered a basic configuration for the investigati ons of the impact of various conditions on the flow through the clearance between the s hrouded turbine blade and the casing. Numerical calculations using Fine/Turbo Numeca were conducted to examine the influence of the rotational velocity and the pressure differ ence across the disk on the flow conditions, especially the mass flow through the clearance....
-
HYDROSTATIC THRUST BEARING WITH REDUCED POWER LOSSES
PublicationIn many cases in rotating machinery, axial load is carried by tilting pad thrust bearings which have been developed since the beginning of 20th century. For high reliability and simplicity, most commonly the bearings are bath lubricated. In the times of sustainable development, however, minimization of friction losses becomes an important criterion for machinery assessment, and a strategic goal of their development. Performed calculations,...
-
NOWE TRENDY I KIERUNKI BADAŃ W MARKETINGU USŁUG
PublicationOd momentu pojawienia się koncepcji marketingu usług przechodzi ona nieustającą ewolucję. Pojawiające się nowe trendy (m.in. Service-Dominant Logic, Service Logic, New Service Marketing) i obszary badań marketingu usług (np. Transformative Service Research) skłaniają do dokonywania podsumowań pewnego etapu rozwoju i stawiania pytań, w którym kierunku powinny podążać badania marketingu usług w przyszłości. Celem artykułu jest przedstawienie...
-
Variable-temperature X-ray diffraction study of structural parameters of NH---S hydrogen bonds in triethylammonium and pyridinium silanethiolates
PublicationHydrogen bonds in triethylammonium and pyridinium silanethiolate salts have been characterized by X-ray, FT–IR and NMR spectroscopies. DFT calculations reveal strongly asymmetric double-well minima at the potential energy curves of the studied compounds
-
On a Method of Efficiency Increasing in Kaplan Turbine
PublicationThis paper presents a method of increasing efficiency in Kaplan-type turbine. The method is based on blade profile optimisation together with modelling the interaction between rotor and stator blades. Loss coefficient was chosen as the optimisation criterion, which is related directly to efficiency. Global optimum was found by means of Genetic Algorithms, and Artificial Neural Networks were utilised for approximations to reduce...
-
Discrete convolution based on polynomial residue representation
PublicationThis paper presents the study of fast discrete convolution calculation with use of the Polynomial Residue Number System (PRNS). Convolution can be based the algorithm similar to polynomial multiplication. The residue arithmetic allows for fast realization of multiplication and addition, which are the most important arithmetic operations in the implementation of convolution. The practical aspects of hardware realization of PRNS...
-
Impact of Urbanization on Stormwater Runoff from a Small Urban Catchment: Gdańsk Małomiejska Basin Case Study
PublicationThis paper deals with the impact of different forms of urbanization on the basin outflow. The influence of changes in land cover/use, drainage system development, reservoirs, and alternative ways of stormwater management (green roofs, permeable pavements) on basin runoff was presented in the case of a small urban basin in Gdańsk (Poland. Seven variants of area development (in the period of 2000-2012) – three historical and four...
-
Elastic scattering of electrons from chloroform
PublicationWe present experimental and theoretical cross sections for elastic electron scattering from CHCl3. This is an important target because of its relevance to environmental chemistry and the plasma etching industry as a source of chlorine radicals. The experimental results were obtained at incident electron energies ranging from 0.5 to 800 eV in the 10deg-130deg scattering angle range. Theoretically, the scattering cross sections in...
-
Nierówności pionowe toru kolejowego
PublicationOcena jakości geometrycznej toru kolejowego wymaga od zarządców infrastruktury stosowania jednolitych metod pomiarów, obliczania i interpretacji wyników. W tym zakresie należy stosować się do norm europejskich i technicznych specyfikacje interoperacyjności. W artykule przedstawiono podstawowe zagadnienia związane z pomiarem i oceną nierówności pionowych toru kolejowego. Zapisano odchyłki dopuszczalne nierówności pionowych według...