Search
displaying 1000 best results Help
Search results for: CYCLONE SEPARATOR
-
Identification of damages in the inlet air duct of a diesel engine based on exhaust gas temperature measurements
PublicationThe temperature of the exhaust gas of a diesel piston engine, measured in the characteristic control sections of its thermo-flow system, can be a valuable source of diagnostic information about the technical condition of the elements limiting the working spaces thus separated, including the turbocharging system, but also its fuel supply system and replacement of the medium. In standard marine engine measurement systems equipped...
-
Nicole Nawrot dr inż.
PeopleDr. Eng. Nicole Nawrot has been employed at the Department of Sanitary Engineering since 2016. In 2021, she obtained a PhD in the field of engineering and technical sciences in the discipline of environmental engineering, mining and energy. Doctoral thesis entitled "Heavy metals in urban retention tanks bottom sediments: distribution, source tracking, and evaluation of phytostabilization adaptability and performance of P. australis...
-
Bearing Capacity of aluminum bars with built-up cross section and glued or welded connections
PublicationThe paper is focused on numerical analysis and experimental test of aluminum bars with glued and welded connections between separate members. The connection properties were tested experimentally. The numerical analysis were conducted for the beam and shell model of the structure. The shape and magnitude of initial geometric imperfection was taken into account
-
Wykorzystanie badań geosyntetyków w projektowaniu warstw filtracyjnych i drenażowych
PublicationW pracy przedstawiono zasady pozwalające na dokonywanie oceny przydatności materiałów geosyntetycznych w projektowaniu warstw separacyjnych i filtracyjno-drenażowych. Najbezpieczniej jest przyjmować za podstawę projektowania podstawowe parametry mechaniczne geosyntetyków (odporność na przebicie, wytrzymałość na rozciąganie, odkształcalność) oraz hydrauliczne (wodoprzepuszczalność, charakterystyczna wielkość porów), pod warunkiem...
-
Subcritical Thermodynamic Cycles with Organic Medium and Isothermal Expansion
PublicationThe efffciencies of the Organic Rankine Cycle (ORC) are not very high and only very seldom do they exceed 20%. The increase and optimization of initial parameters and certain modifications of the thermodynamic cycle make it possible to overcome these drawbacks. A new modified cycle has been described and analyzed in detail in the paper. Similarly to the Ericsson cycle for gas turbines, isothermal expansion in the turbine is suggested...
-
Energy, water detailed usage. Living lab testing for sustainable urban food-water-energy cycle. Jan. 2022
Open Research DataData set contains detailed, continuous measurements of the usage of water and electrical energy (AC power) in an experimental facility set up in a scientific laboratory (Laboratorium im. B.Niemkiewicza) at the Faculty of Mechanical Engineering and Ocean Technology of the Gdansk University of Technology. The test bed was established in co-operation...
-
Energy, water detailed usage. Living lab testing for sustainable urban food-water-energy cycle. Dec. 2021
Open Research DataData set contains detailed, continuous measurements of the usage of water and electrical energy (AC power) in an experimental facility set up in a scientific laboratory (Laboratorium im. B.Niemkiewicza) at the Faculty of Mechanical Engineering and Ocean Technology of the Gdansk University of Technology. The test bed was established in co-operation...
-
Sprzętowa implementacja transformacji Hougha w czasie rzeczywistym
PublicationW artykule przedstawiono implementację sprzętową w FPGA algorytmu do wykrywania kształtów aproksymowanych zbiorem linii prostych podczas przetwarzania obrazu cyfrowego w czasie rzeczywistym. W opracowanej strukturze sprzętowej podniesiono efektywność przetwarzania poprzez zastosowanie przetwarzania przepływowego, lookup table, wykorzystanie wyłącznie arytmetyki liczb całkowitych oraz rozproszenie pamięci głosowania. Eksperymentalnie...
-
Extending loophole-free nonlocal correlations to arbitrarily large distances
PublicationQuantum theory allows spatially separated observers to share nonlocal correlations, which enable them to accomplish classically inconceivable information processing and cryptographic feats. However, the distances over which nonlocal correlations can be realized remain severely limited due to their high fragility to noise and high threshold detection efficiencies. To enable loophole- free nonlocality across large distances, we introduce...
-
Entangled rendezvous: a possible application of Bell non-locality for mobile agents on networks
PublicationRendezvous is an old problem of assuring that two or more parties, initially separated, not knowing the position of each other, and not allowed to communicate, are striving to meet without pre-agreement on the meeting point. This problem has been extensively studied in classical computer science and has vivid importance to modern and future applications. Quantum non-locality, like Bell inequality violation, has shown that in many...
-
Robert Jankowski prof. dr hab. inż.
PeopleHe was born on December 26, 1968 in Gdynia. A graduate of the High School at the Consulate of Poland in Benghazi, Libya (1987), a student at the Gdańsk University of Technology (MSc studies, 1987-1991 and 1992-1993), University of Sheffield, England (BSc studies, 1991-1992), University of Roskilde, Denmark (MSc course, 1993) and University of Tokyo, Japan (PhD studies, 1994-1997). From the beginning of his professional career associated...
-
Determination of trace levels of eleven bisphenol A analogues in human blood serum by high performance liquid chromatography–tandem mass spectrometry
PublicationChemicals showing structural or functional similarity to bisphenol A (BPA), commonly called BPA analogues, have recently drawn scientific attention due to their common industrial and commercial application as a substitute for BPA. In the European Union, the use of BPA has been severely restricted by law due to its endocrine disrupting properties. Unfortunately, it seems that all BPA analogues show comparable biological activity,...
-
Multifrequency Wideband Sonar Array
PublicationThis paper describes of new approach to Multifrequency Wideband Arrays (MWA),applied piezocomposite technologies of the array elements. MWA operating in transmitting(Tx) and receiving (Rx) mode on two or three bands, requires state-of-the-art technology andefficient array designing than conventional array in which separate arrays for every band oreven separate Tx and Rx transducers/arrays are used. The new piezocomposite elements...
-
Przeliczanie jednostek miar - proste, a jednak kłopotliwe
PublicationPoprawność pisowni separatora dziesiętnego, jednostek miary oraz wartości mianowanych w układzie metrycznym jednostek miar (SI). Dwa słynne przykłady katastrof spowodowanych błędami przeliczania wartości pomiędzy układami jednostek miar: anglosaskim i metrycznym (SI). Wyjaśnienie przyczyny błędnego wzoru Minikina znanego szeroko w inżynierii morskiej, portowej i brzegowej. Proste zadanie rachunkowe z tematu rurociągu podmorskiego,...
-
On Accuracy Modeling of Gas Turbine Cycles by the In-house COM-GAS Code
PublicationIn this paper, a comparison of accuracy modeling of gas turbine cycles between the basic (classical) model and the in-house COM-GAS code has been presented. The basic model uses a semi-perfect gas and well known projecting assumption. On the other hand, the computational flow mechanics (CFM) basis on a real gas by using thermodynamic tables. The thermodynamic analysis of thermal cycles, simply gas cycle GT8C and gas turbine cycle...
-
Alternative cogeneration thermodynamic cycles for domestic ORC
PublicationThe Organic Flash Cycle (OFC) is suggested as a vapor power cycle that could potentially improve the efficiency of utilization of the heat source. Low and medium temperature finite thermal sources are considered in the cycle. Additionally the OFC’s aim is to reduce temperature difference during heat addition. The study examines 2 different fluids. Comparisons are drawn between the OFC and an optimized basic Organic Rankine Cycle...
-
Methods of Cyclist Training in Europe
PublicationThe following study aims to address the issue of cyclist training methodologies. Recent European bicycle accident statistics reveal a troubling upward trend. A potential solution to mitigate such incidents involves providing cyclists with comprehensive training encompassing traffic regulations and interactions with fellow road users. We conducted a comparative analysis of the cycling education approaches and cyclist training systems...
-
Galvanostatic cycling with potential limitation (GCPL) of WS2/userGOx (composites of tungsten disulfide and ultrafast self-expanded and reduced graphene oxide) and ex-WS2 (exfoliated tungsten disulfide)
Open Research DataThese data contain results of galvanostatic cycling with potential limitation (GCPL) of WS2/userGOx (composites of tungsten disulfide and ultrafast self-expanded and reduced graphene oxide) and ex-WS2 (exfoliated tungsten disulfide). The data were collected for samples obtained from three ex-WS2:GO dispersions - with 1:1, 1:2, and 2:1 weight ratios.
-
Thermographic imaging of electrochemical double layer capacitors during cycling charging - discharging 0 - 2,7 V at 64 mA. Sample 91. Image period: 5 sec.
Open Research DataDataset contains thermal images of prototype electrochemical double layer capacitor taken during cyclic charging - discharging. The sample was charged to 2,7 V and discharged to 10 mV by constant current 64 mA. Sample 91. Pictures were taken relatively fast, with period of 5 sec in order to examine the fast fluctuations of sample temperature during...
-
Thermographic imaging of electrochemical double layer capacitors during cycling charging - discharging 0 - 2,7 V at 120 mA. Sample 103. Image period: 0,5 sec.
Open Research DataDataset contains thermal images of prototype electrochemical double layer capacitor taken during cyclic charging - discharging. The sample was charged to 2,7 V and discharged to 10 mV by constant current 120 mA. Sample 103. Thermographic pictures were taken relatively fast, with period of 0,5 sec in order to examine the fast fluctuations of sample...
-
Thermographic imaging of electrochemical double layer capacitors during cycling charging - discharging 0 - 3,6 V at 420 mA. Sample 103. Image period: 0,5 sec.
Open Research DataDataset contains thermal images of prototype electrochemical double layer capacitor taken during cyclic charging - discharging. The sample was charged to 3,6 V and discharged to 10 mV by constant current 420 mA. Sample 103. Pictures were taken with period of 0,5 sec (2 Hz) in order to examine the fast fluctuations of sample temperature during charging...
-
Thermographic imaging of electrochemical double layer capacitors during cycling charging - discharging 0 - 3,4 V at 420 mA. Sample 103. Image period: 0,5 sec.
Open Research DataDataset contains thermal images of prototype electrochemical double layer capacitor taken during cyclic charging - discharging. The sample was charged to 3,4 V and discharged to 10 mV by constant current 420 mA. Sample 103. Pictures were taken with period of 0,5 sec (2 Hz) in order to examine the fast fluctuations of sample temperature during charging...
-
Thermographic imaging of electrochemical double layer capacitors during cycling charging - discharging 0 - 3,3 V at 420 mA. Sample 103. Image period: 2 sec.
Open Research DataDataset contains thermal images of prototype electrochemical double layer capacitor taken during cyclic charging - discharging. The sample was charged to 3,3 V and discharged to 10 mV by constant current 420 mA. Sample 103. Pictures were taken relatively fast, with period of 2 sec in order to examine the fast fluctuations of sample temperature during...
-
Thermographic imaging of electrochemical double layer capacitors during cycling charging - discharging 0 - 3,6 V at 420 mA. Sample 103. Image period: 0,5 sec.
Open Research DataDataset contains thermal images of prototype electrochemical double layer capacitor taken during cyclic charging - discharging. The sample was charged to 3,6 V and discharged to 10 mV by constant current 420 mA. Sample 103. Pictures were taken with period of 0,5 sec (2 Hz) in order to examine the fast fluctuations of sample temperature during charging...
-
Thermographic imaging of electrochemical double layer capacitors during cycling charging - discharging 0 - 3,5 V at 420 mA. Sample 103. Image period: 0,5 sec.
Open Research DataDataset contains thermal images of prototype electrochemical double layer capacitor taken during cyclic charging - discharging. The sample was charged to 3,5 V and discharged to 10 mV by constant current 420 mA. Sample 103. Pictures were taken with period of 0,5 sec (2 Hz) in order to examine the fast fluctuations of sample temperature during charging...
-
Thermographic imaging of electrochemical double layer capacitors during cycling charging - discharging 0 - 3,6 V at 420 mA. Sample 103. Image period: 1 sec.
Open Research DataDataset contains thermal images of prototype electrochemical double layer capacitor taken during cyclic charging - discharging. The sample was charged to 3,6 V and discharged to 10 mV by constant current 420 mA. Sample 103. Pictures were taken with period of 1 sec (1 Hz) in order to examine the fast fluctuations of sample temperature during charging...
-
Thermographic imaging of electrochemical double layer capacitors during cycling charging - discharging 0 - 3,6 V at 420 mA. Sample 103. Image period: 1 sec.
Open Research DataDataset contains thermal images of prototype electrochemical double layer capacitor taken during cyclic charging - discharging. The sample was charged to 3,6 V and discharged to 10 mV by constant current 420 mA. Sample 103. Pictures were taken with period of 1 sec (1 Hz) in order to examine the fast fluctuations of sample temperature during charging...
-
Thermographic imaging of electrochemical double layer capacitors during cycling charging - discharging 0 - 3,4 V at 420 mA. Sample 103. Image period: 1 sec.
Open Research DataDataset contains thermal images of prototype electrochemical double layer capacitor taken during cyclic charging - discharging. The sample was charged to 3,4 V and discharged to 10 mV by constant current 420 mA. Sample 103. Pictures were taken with period of 1 sec in order to examine the fast fluctuations of sample temperature during charging - discharging...
-
Separability Assessment of Selected Types of Vehicle-Associated Noise
PublicationMusic Information Retrieval (MIR) area as well as development of speech and environmental information recognition techniques brought various tools in-tended for recognizing low-level features of acoustic signals based on a set of calculated parameters. In this study, the MIRtoolbox MATLAB tool, designed for music parameter extraction, is used to obtain a vector of parameters to check whether they are suitable for separation of...
-
A green route for high-performance bio-based polyurethanes synthesized from modified bio-based isocyanates
PublicationThe need for sustainability and a circular economy leads to the development of innovative greener materials and technologies. This paper is focused on a novel class of bio-based polyurethanes (PUs) synthesized with the use of bio-monomers including bio-based isocyanates. The novelty of this work is related to the usage of bio-based modified isocyanate via a two-step solvent-free synthesis of novel cast bio-based poly(ester-urethanes)...
-
Chemical composition of shells from red (Strongylocentrotus franciscanum) and green (Strongylocentrotus droeba-chiensis) sea urchin
PublicationThe shells from red and green sea urchins accounted for 47.9 and 40.7% of their body weights, respectively. The red and green sea urchin shells contained 91.08 and 90.77% minerals and 4.06 and 4.99% proteins, respectively. The shells did not contain any chitin. Sea urchin shells had a relatively large amount of naphthoquinone pigments, 121 mg per 100 g in red and 163 mg per 100 g in green species. The small quantities of glucosamine...
-
Monitorowanie temperatury elementów wykonawczych docierarki jednotarczowej
PublicationW rozdziale przedstawiono badania monitorowania temperatury elementów układu kinematycznego docierarki jednotarczowej przy użyciu metody termowizyjnej. Badano temperaturę tarczy docierającej podczas jej wyrównywania, temperaturę pierścieni i rolek prowadzących, separatorów oraz przedmiotów obrabianych z miedzi i żeliwa. W badaniach stosowano różne wartości prędkości obrotowych tarcz docierających oraz ziarnistości ścierniw.
-
Development of a vortex-assisted switchable-hydrophilicity solvent-based liquid phase microextraction for fast and reliable extraction of Zn (II), Fe (II), Pb (II), and Cd (II) from various baby food products
PublicationThis manuscript describes the development of a novel liquid phase microextraction (LPME) method for the extraction and determination of Zn (II), Fe (II), Pb (II), and Cd (II) in various infant/baby food and supplements products. The method is based on vortex-assisted extraction combined with a switchable-hydrophilicity solvent (SHS) sample preparation. The SHS, which undergoes reversible phase changes triggered by pH change, enables...
-
Review on the quality of sediments from the stormwater drainage system in the urban area
PublicationThe main task of the stormwater drainage system is a safe drainage of rainwater and snowmelt from the urban area to the receiver. The flow of rain water in the drainage pipes is directly related with the formation of sediments in the whole stormwater system. In addition, pollutants from land runoff get adsorbed to the sediments. The sludge is mainly formed in those elements of stormwater drainage system, wherein the flow conditions...
-
Sieć wielodomenowa wykorzystująca MPLS i SDN
PublicationTechnologia Wieloprotokołowej Komutacji Etykietowej (MPLS – MultiProtocol Label Switching) dostarcza odpowiednie mechanizmy wspierające proces zachowania jakości usług, jednak wymaga nadrzędnego elementu sterującego. Takim elementem może być kontroler zrealizowany w koncepcji Sieci Definiowanych Programowo (SDN – Software Defined Networking), wprowadzający abstrakcję, rozdzielającą płaszczyznę przekazywania od płaszczyzny sterowania....
-
Assessment of the Environmental Impact of a Car Tire throughout Its Lifecycle Using the LCA Method
PublicationThere are numerous threats to the natural environment that pose a significant risk both to the environment and to human health, including car tires. Thus, there is a need to determine the impact of the life cycle of car tires on the environment, starting with the processes of raw materials acquisition, production, and ending with end-of-life management. Therefore, the authors of this study chose to do research on passenger car...
-
Aleksandra Parteka dr hab. inż.
PeopleAbout me: I am an associate professor and head of doctoral studies at the Faculty of Management and Economics, Gdansk University of Technology (GdanskTech, Poland). I got my MSc degree in Economics from Gdansk University of Technology (2003) and Universita’ Politecnica delle Marche (2005), as well as MA degree in Contemporary European Studies from Sussex University (2006, with distinction). I received my PhD in Economics...
-
Evaluation the P-Delta Effect on Collapse Capacity of Adjacent Structures Subjected to Far-field Ground Motions
PublicationIn urban areas, adjacent structures can be seen in any insufficient distance from each other, because of economic reasons and refusal of acquired minimum separation distance according to seismic previsions. Collapse capacity assessment of structures is one of the important objectives of performance-based seismic engineering. The purpose of this study is to consider the pounding phenomenon and P-Delta effect in seismic collapse...
-
The Design of Cavity Resonators and Microwave Filters Applying Shape Deformation Techniques
PublicationThis article introduces shape deformation as a new approach to the computer-aided design (CAD) of high-frequency components. We show that geometry deformation opens up new design possibilities and offers additional degrees of freedom in the 3-D modeling of microwave structures. Such design flexibility is highly desirable if the full potential of additive manufacturing (AM) is to be exploited in the fabrication of RF and microwave...
-
Wielopoziomowe przekształtniki średniego napięcia (SN) o budowie modułowej
PublicationW artykule omówiono wybrane zagadnienia dotyczące zastosowań wielopoziomowych przekształtników średniego napięcia (SN) w układach napędowych o regulowanej prędkości, zwłaszcza w układach z izolacją od sieci zasilającej. W opracowanym przekształtniku zastosowano izolację galwaniczną od sieci zrealizowaną za pomocą izolowanych przetwornic dc-dc z transformatorami wysokiej częstotliwości (> 5 kHz). Przedstawiono zarejestrowane przebiegi...
-
An advanced thermal-FSI approach of an evaporation of air heat pump
PublicationThe paper presents selected problems of numerical modeling of an advanced thermal-FSI approach of evaporator of air heat pomp. The example of a fin-tube evaporator has been studied, focusing on obtaining of heat exchanger characteristics applying two-phase flow model for the in-tube refrigerant flow. Special attention is given to heat transfer between separated medium for different air velocity and changed refrigerant mass flow...
-
Experimental Extraction of Secure Correlations from a Noisy Private State
PublicationWe report experimental generation of a noisy entangled four-photon state that exhibits a separation between the secure key contents and distillable entanglement, a hallmark feature of the recently established quantum theory of private states. The privacy analysis, based on the full tomographic reconstruction of the prepared state, is utilized in a proof-of-principle key generation. The inferiority of distillation-based strategies...
-
Study of the effect of adiabatic heating on the operation of the electrodynamic actuator
PublicationElectrodynamic actuators are used in hybrid switching systems where a very quick contact separation as well as operation repeatability and long-term reliability are required. The article presents selected results of thermal studies in the electrodynamic drive system. Study was carried out on the basis of the 3D electromagneto-thermal model implemented in the Ansys_Maxwell environment. The present model allows to determine the critical...
-
MODEL FOR MEASUREMENT OF FLOW INSTALLATION TIME IN SDN SWITCH
PublicationSDN is the approach in telecommunication networks that separates control plane from data forwarding plane by specifying a single network entity as a controller that defines rules (called flows) of traffic forwarding for the switches connected to it. The time that is required for installation of these rules might be a hindrance for the overall performance of SDN network. In the paper, a model for testing and evaluating the influence...
-
Macromodels for efficient FEM simulations of waveguides and resonators
PublicationThis paper introduces a novel technique for enhancing the efficiency of the finite element method (FEM) by incorporating special modules, called macromodels, into the standard eigenvalue formulation. The number of unknowns in the separated macromodel subdomain can be significantly reduced by orthogonal projection, using the efficient nodal order reduction algorithm. The idea of macromodels implementation is demonstrated on a simple...
-
Energochłonność docierania powierzchni płaskich elementów ceramicznych.
PublicationPrzedstawiono wyniki badań docierania jednotarczowego powierzchni płaskich elementów ceramicznych. Badano wpływ nacisku jednostkowego, prędkości i czasu docierania na wydajność procesu, moc i energochłonność. W badaniach stosowano mikroziarna węglika boru i docieraki żeliwne aktywizowane w sposób swobodny. Minimalizacja energochłonności docierania jest możliwa przez zmniejszenie czasu obróbki, przy zachowaniu maksymalnego...
-
Integrated production technology of cylindrical surfaces by turning and burnishing
PublicationThe method is based on a combination of previously used two separate operations namely machining and burnishing in a one complex operation implemented on a lathe.In the case of machining shafts and hydraulic cylinders of steel C45 is possible to obtain a surface roughness Ra=0,16 - 0,32 micrometers, dimensional accuracy class 7-8 according to ISO standards, and increase in the hardness of the surface up to 40%.
-
N-doped carbon materials as electrodes for highly stable supercapacitors
PublicationThis article reports a strategy to use nitrogen-doped carbon materials as electrodes for supercapacitors. Depending on the carbon precursor, the porous structure is changed with specific surface area reached up to 2270 m2 g−1. The capacitance of carbon materials used as electrodes is related strictly to pore size. The microstructure and nitrogen functionalities enable a high capacitance (327 F g−1) and cycle durability. The nanoporous...
-
NMR dispersion studies of poly(ethylene oxide)/sodium montmorillonitenanocomposites
PublicationPraca prezentuje wyniki badań dotyczące struktury nanokompozytów opartych na matrycy poli(tlenku etylenu) zawierającej montmorylonit sodowy. Układy zawierające PEO/MMT scharakteryzowano metodami NMR (Fast Field Cycling NMR), DSC oraz XRD.
-
A study of the photoelectron spectra of α-tetrahydrofurfuryl alcohol over the outer valence energy region (9–25 eV)
PublicationPhotoelectron spectra of α-tetrahydrofurfuryl alcohol (THFA) molecules, the threshold spectrum and spectra for constant photoelectron energies, have been measured over the photon energy range 9–25 eV. Analysis of the photoelectron spectra has allowed overlapping photoionization bands to be separated, tentatively assigned and their vertical photoionization energies to be determined. These energies are compared with existing theoretical...