Filters
total: 2166
displaying 1000 best results Help
Search results for: TRANSVERSAL SKILLS
-
On FE modelling of fully saturated soils
PublicationPrzedstawiono podstawy modelowania gruntów nasyconych w ramach metody elementów skończonych. Przedstawiono szczegółowo podstawowe równania różniczkowe problemu oraz ich słabą formę potrzebną w dyskretyzacji w metodzie elementów skończonych. Porównano dwie podstawowe metody formułowania elementów skończonych: uproszczoną u-p oraz pełną u-p-w. Omówiono podstawowe różnice i ograniczenia metody uproszczonej. Artykuł w swej rozszerzonej...
-
Fate of Ionic Liquids in Soils and Sediments
PublicationZrozumienie losu cieczy jonowych w glebach i osadach dennych jest istotnym elementem ich implementacji z zachowaniem idei zrównoważonego rozwoju. Niniejsza publikacja zawiera analizę i podsumowanie danych dotyczących oddziaływań cieczy jonowych w roztworach wodnych oraz agregacji na powierzchniach stałych. Zaobserwowano, że silnie lipofilowe ciecze jonowe zawierające długi łańcuch węglowodorowy lub duży organiczny anion wykazują...
-
Deep compaction control of sandy soils
PublicationVibroflotation, vibratory compaction, micro-blasting or heavy tamping are typical improvement methods for the cohesionless deposits of high thickness. The complex mechanism of deep soil compaction is related to void ratio decrease with grain rearrangements, lateral stress increase, prestressing effect of certain number of load cycles, water pressure dissipation, aging and other effects. Calibration chamber based interpretation...
-
Interaction of Novel Ionic Liquids with Soils
PublicationWith the constant development of new ionic liquids, the understanding of the chemical fate of these compounds also needs to be updated. To this effect, in this contribution, the interaction of a number of novel ionic liquids with soils was determined. Therefore, three novel headgroups (ammonium, phosphonium or pyrrolidinium) with single or quaternary substitution were tested on a variety of soils with high to low organic matter...
-
Liapunov instability of the hypoplastic model for soils.
PublicationWskazanie na konieczność wprowadzenia do hipoplastycznego modelu konstytutywnego tzw. sprężystego jądra. Bez niego model okazuje się być niestabilny w sensie Liapunowa.
-
SOILS AND FOUNDATIONS
Journals -
Technology of an adhesive silicone film as drug carrier in transdermal therapy I. Analytical methods used for characterization and design of the universal elastomer layers
PublicationSilicone polymers possess unique properties, which make them suitable for many different applications, for example in the pharmaceutical and medical industry. To create an adhesive silicone film, the appropriate silicone components have to be chosen first. From these components two layers were made: an adhesive elastomer applied on the skin, and a non-adhesive elastomer on the other side of the film. The aim of this study was...
-
Mangiferin and Hesperidin Transdermal Distribution and Permeability through the Skin from Solutions and Honeybush Extracts (Cyclopia sp.)—A Comparison Ex Vivo Study
Publication -
A study on fibre-reinforced concrete elements properties based on the case of habitat modules in the underwater sills
PublicationHydrotechnical constructions are mostly objects functioning in extreme conditions and requiring a custom-made construction project. In the case of using prefabricated elements, it is required to develop production, transport, assembly, conservation and repair technology. Concerning the problem of concrete cracks, modern repair systems allow positive effects to be achieved in many cases of concrete elements repair. In this work...
-
Anti-plane shear waves in an elastic strip rigidly attached to an elastic half-space
PublicationWe consider the anti-plane shear waves in a domain consisting of an infinite layer with a thin coating lying on an elastic half-space. The elastic properties of the coating, layer, and half-space are assumed to be different. On the free upper surface we assume the compatibility condition within the Gurtin–Murdoch surface elasticity, whereas at the plane interface we consider perfect contact. For this problem there exist two possible...
-
Wykorzystanie metody FMEA w kształtowaniu umiejętności projektowania technologii części maszyn = application of the FMEA method for skills development of machine parts technology desing
PublicationPrzedstawiono sposób wykorzystania metody FMEA w kształtowaniu umiejętności projektowania technologii części maszyn. Podano wytyczne ogólne i etapy analizy procesu i konstrukcji. Zamieszczono przykład analizy technologii dwustronnej dźwigni spawanej w produkcji małoseryjnej.
-
On continuity conditions at the phase interface of two-phase elastic shells
PublicationW pracy rozwinięto ogólną nieliniową teorię powłok sprężystych podlegających przejściom fazowym typu martenzytowego. Przedstawione sformułowanie oparte jest na statycznie i kinematycznie ścisłym modelu powłokowym. Uwzględniono gęstośc energii odkształcenia, jak również siły i momenty zadane wzdłuż krzywoliniowego przejścia fazowego. W szczególności otrzymano statyczne warunki ciągłości wzdłuż koherentnego połączenia oraz połączenia...
-
Numerical analysis of laminated shells under in-plane axial compression
PublicationW pracy analizowana jest stateczność powłoki warstwowej poddanej osiowemu ściskaniu. Badany jest wpływ wariantów uwarstwienia oraz warunków podparcia krawędzi obciążonej na zachowanie konstrukcji. Wyniki numeryczne porównano z eksperymentem.
-
On shear correction factors in the non-linear theory of elastic shells
PublicationW pracy wyprowadzono analitycznie wartości korekcyjnych współczynników ścinania dla ścinania poprzecznego oraz dla momentów owinięcia w ramach nieliniowej sześcioparametrowej teorii powłok. Wartości wyprowadzono poprzez odpowiednie sformułowanie komplementarnej energii sprężystej. Na drodze analizy przy pomocy MES, badano wpływ wartości współczynników na położenie punktów bifurkacji, deformacje, całkowitą energię sprężystą układu...
-
Elastoplastic nonlinear FEM analysis of FGM shells of Cosserat type
PublicationThe paper is a continuation of [1] where the formulation of the elastic constitutive law for functionally graded materials (FGM) on the grounds of nonlinear 6-parameter shell theory with the 6th parameter (the drilling degree of freedom) was presented. Here the formulation is extended to the elasto-plastic range. The material law is based on Cosserat plasticity and employs the well-known Tamura-Tomota-Ozawa (TTO) [2] mixture...
-
On refined constitutive equations in the six-field theory of elastic shells
PublicationWithin the resultant six-field shell theory, the second approximation to the complementary energy density of an isotropic elastic shell undergoing small strains is constructed. In this case, the resultant drilling couples are expressed explicitly by the stress resultants and stress couples as well as by amplitudes of the quadratic and cubic distributions of an intrinsic deviation vector. The refined 2D strain-stress and stress-strain...
-
Thermo-elastic non-linear analysis of multilayered plates and shells
PublicationGeometrically nonlinear FEM analysis of multilayered composite plates and shells is performed in order to resolve the stability problem of the structures being under the influence of temperature field. The Riks-Wempner-Ramm algorithm with a specially modified multi-choice unloading condition has been implemented in authors’ numerical code. As the representation of multilayered medium the Equivalent Single Layer approach with the...
-
Nonlinear material identification of heterogeneous isogeometric Kirchhoff–Love shells
PublicationThis work presents a Finite Element Model Updating inverse methodology for reconstructing heterogeneous materialdistributions based on an efficient isogeometric shell formulation. It uses nonlinear hyperelastic material models suitable fordescribing incompressible material behavior as well as initially curved shells. The material distribution is discretized by bilinearelements such that the nodal values...
-
On the FEM implementation of the large rotation shell theory for elasticanisotropic shells.
PublicationW pracy przedstawiono problemy implementacji MES teorii powłok o dużych obrotach w statycznej, geometrycznie nieliniowej analizie konstrukcji warstwowych. Zwrócono uwagę na właściwą interpretacje rotacyjnych stopni swobody w algorytmie MES. Omówiono wariant dużych i skończonych obrotów. Przedstawiono wyniki obliczeń dla znanego w literaturze przykładu analizy paneli kompozytowej w zakresie dużych obrotów.
-
Predicting mobility of alkylimidazolium ionic liquids in soils
PublicationCiecze jonowe są nową grupą związków chemicznych stanowiących idealne, nielotne medium reakcyjne dla wielu procesów technologicznych jak synteza organiczna i biokataliza, będące alternatywnymi elektrolitrami, fazami reakcyjnymi lub modyfikatorami faz oraz smarami. Ich implementacja na szeroką skalę pociągnie za sobą zastosowania w rozmaitych procesach przemysłowych. Biorąc pod uwagę ich dużą stabilność, mogą one przedostać się...
-
Buckling of cylindrical silos containing bulk solids.
PublicationOmówiono problem wyboczenia stalowych silosów wypełnionych materiałem sypkim. Obliczenia wykonano dla płaskiego stanu odkształcenia i dla osiowo-symetrycznego. Zachowanie materiału sypkiego było modelowane mikropolarnym hipoplastycznym prawem materiałowym, a zachowanie ścian silosu mikropolarnym sprężysto-plastycznym prawem wg von Misesa. W obliczeniach uwzględniono różne formy imperfekcji na ścianach. Wyniki porównano z silosami...
-
The influence of bulk solids on buckling strength of silos.
PublicationW artykule przedstawiono wyniki numerycznej anlizy wyboczenia ścian silosu osiowo-symetrycznego wypełnionego materiałem sypkim. Zachowanie ściany było modelowane mikropolarnym prawem sprężysto-plastycznym, natomiast zachowanie materiału sypkiego mikropolarnym prawem hipoplastycznym. Oszacowano wpływ materiału sypkiego na nośność wyboczenia silosów.
-
Design of septic tanks placed on cohesive soils
PublicationThe paper presents a short review of literature with regard to design and erection of the reinforced concrete and concrete tanks. The authors investigated the underground septic tank with of 10 m3 capacity placed on cohesive soils. The authors compared the values of internal forces for soils in drained and undrained conditions with different geotechnical parameters: loamy sand of liquidity index IL = 0.1 and IL = 0.7 and clay with...
-
Knowledge pills in Education and Training: A Literature Review
PublicationObject and purpose: Knowledge pills (KPs) are a technique for transferring knowledge through short factual batches of content. In education and vocational training, they can help learners acquire specific pieces of knowledge in a few minutes, through a “microteaching” approach where learners can be involved in active and interactive exercises, quizzes, and games. Thanks to the advancements of multimedia platforms, they can contain...
-
Modelling the time-dependent behaviour of soft soils
PublicationTime-dependence of soft soils has already been thoroughly investigated. The knowledge on creep and relaxation phenomena is generally available in the literature. However, it is still rarely applied in practice. Regarding the organic soils, geotechnical engineers mostly base their calculations on the simple assumptions. Yet, as presented within this paper, the rate-dependent behaviour of soft soils is a very special and important...
-
Loads on walls and inserts in a mass-flow silos
PublicationArtykuł przedstawia numeryczną symulację przepływu materiału sypkiego w silosach z uwzględnieniem wkładki silosowej o kształcie podwójnego stożka. Pokazany został wpływ zamontowanej wkładki na rodzaj przepływu oraz na wartość i kształt naporu na ścianę silosu.
-
Dynamic effects during emptying of large silos.
PublicationPublikacja obejmuje zagadnienie rezonansowych efektów dynamicznych występujących podczas opróżniania silosów zawierających materiały sypkie
-
Finite element models used in diagnostics of transverse cracks in bridge approach pavement
Open Research DataTransverse cracks in the asphalt pavement were observed on bridge structures next to single-module expansion joints with a 5 meter approach slab set at the depth of 1 m. The finite element (FE) models of the approach pavement were created to investigate the reasons of premature cracking and crack initiation mechanism over the back edge of the abutment...
-
Fem analysis of cosserat plates and shells based on some constitutive relations
PublicationPrzeprowadzono studium doboru mikropolarnych współczynników konstytutywnych w pewnym modelu płyty Cosseratów. Wyznaczono ograniczenia na ich wartości i przeprowadzono parametryczną analizę wpływu tych współczynników na geometrycznie nieliniowe deformacje powłok z ortogonalnymi przecięciami płatów.
-
Geometrically nonlinear finite element simulation of smart piezolaminated plates and shells
PublicationW pracy zaproponowano powłokowy element skończony pozwalający na uwzględnienie efektu piezoelektrycznego. Element został wykorzystany w podejściu Lagrange'a, które wymaga starannego dobrania definicji wielkości mechanicznych i elektrycznych. Zależności przemieszczenie-odkształcenie zbudowano na bazie teorii małych odkształceń i umiarkowanych obrotów. Założono liniowy rozkład pól odkształceń i pola elektrycznego po grubości powłoki....
-
Four-node semi-EAS element in six-field nonlineartheory of shells
PublicationW pracy sformułowano 4-węzłowy powłokowy element skończony dla konstrukcji powłokowych. Element opracowano w ramach nieliniowej 6-parametrowej teorii powłok z niesymetrycznymi miarami odkształceń membranowych. Kinematyka powłoki jest opisana przez dwa pola: translacji i obrotów, przy czym wszystkie trzy parametry obrotu traktowane są jako niezależne. W wyniku tego sformułowany element nadaje się do analizy struktur powłokowych...
-
Modelling and FE-simulation of plastic ductile damage evolution in plates and shells
Publication -
Extended non-linear relations of elastic shells undergoing phase transitions
PublicationThe non-linear theory of elastic shells undergoing phase transitions was proposed by two first authors in J. Elast. 79, 67-86 (2004). In the present paper the theory is extended by taking into account also the elastic strain energy density of the curvilinear phase interface as well as the resultant forces and couples acting along the interface surface curve itself. All shell relations are found from the variational principle of...
-
In-plane shear nonlinearity in failure behavior of angle-ply laminated shells
PublicationThe paper concerns the progressive failure analysis of laminates with the in-plane shear nonlinearity accounted for.The nonlinear shear response of the layer is described by the constitutive relation treating the stresses as a function of strains. Thus it can be easily incorporated into the displacement-based FEM codes. The brittle failure mechanisms of the fibers and the matrix of the layer are recognized with the use of the Hashin...
-
Generation of random fields to reflect material and geometric imperfections of plates and shells
PublicationThe paper covers two patterns of random field generation: conditional acceptance – rejection method and Karhunen – Loève expansion. The generation of two-dimensional random fields is essential in plates and shells analysis, allowing for a relevant limit and critical state assessment of geometrically and ma-terially imperfect structures. The features of both generation methods dedicate them to selected problems.
-
Nonlinear FEM analysis of irregular shells composed of fiber metal laminates
PublicationThe paper deals with the analysis of failure initiation in shells made of Fiber Metal Laminates (FML). The elas-tic material law for orthotropic lamina is stated accounting for asymmetric in-plane stress and strain measures. The asymmetry results from the employed general nonlinear 6-field shell theory where the generalized dis-placements involve the translation and the proper rotation field. The novelty of the presented results...
-
Arc-length Algorithm Efficiency in the Analysis of Thermally Loaded Multilayered Shells
PublicationThis paper concerns the efficiency study of the arc-length algorithm in the geometrically non-linear analysis of thermally loaded multilayered shells. The thermal loading is considered as the one-way thermo-mechanical coupling effect. Two implementations of the arc-length method are examined: the path-following technique available in NX-Nastran and the RiksWempner-Ramm algorithm adopted in the authors’ computer code SHLTH. It is...
-
On Solvability of Boundary Value Problems for Elastic Micropolar Shells with Rigid Inclusions
PublicationIn the framework of the linear theory of micropolar shells, existence and uniqueness theorems for weak solutions of boundary value problems describing small deformations of elastic micropolar shells connected to a system of absolutely rigid bodies are proved. The definition of a weak solution is based on the principle of virial movements. A feature of this problem is non-standard boundary conditions at the interface between the...
-
On the exact equilibrium conditions of irregular shells reinforced by beams along the junctions
PublicationThe exact, resultant equilibrium conditions for irregular shells reinforced by beams along the junctions are formulated. The equilibrium conditions are derived by performing direct integration of the global equilibrium conditions of continuum mechanics. New, exact resultant static continuity conditions along the singular curve modelling reinforced junction are presented. The results do not depend on shell thickness, internal through-the-thickness...
-
Analysis of material properties of technical fabric for hanging roofs andpneumatic shells.
PublicationPrzedyskutowano zastosowanie w metodzie elementów skończonych specjalnego modelu elementu do analizy tkanin technicznych. Przedstawiono specjalne postępowanie z typowym elementem w płaskim w stanie naprężenia, tak aby uwzględnić można było zjawiska charakterystyczne dla tkanin technicznych. Zaproponowany model pozwala na zastosowanie niesprężystych związków konstytutywnych a w szczególności związków lepkoplastycznych. Opisano doświadczenia...
-
Critical examination of benchmark problems for large rotation analysis of laminated shells
PublicationW pracy przedstawiono krytyczny przegląd przykładów testowych stosowanych w analizie dużych obrotów powłok warstwowych. Kilka przykładów wyselekcjonowanych z literatury zostało przeanalizowanych przy użyciu własnych programów autora bazujących na różnych poziomach nieliniowości geometrycznej. Wyniki analizy porównawczej pozwoliły na wysunięcie wniosków o przydatności badanych przykładów jako testów sprawdzających w analizie dużych...
-
Gdańsk University of Technology graduates’ self-assessment of the use of digital skills in professional work – the year 2017
Open Research DataThe dataset includes data from the survey on the Gdańsk University of Technology graduates' from the year 2017 on their self-assessment of the use of digital skills in professional work. The survey was conducted in 2019, two years after the respondents obtained graduate status. The research sample included 1594 respondents. To summarize, the vast majority...
-
Gdańsk University of Technology graduates’ assessment of acquired skills and competencies for professional work – years 2011-2013
Open Research DataThe dataset includes data from the survey on the Gdańsk University of Technology graduates' from the years 2011-2013 on their assessment of acquired skills and competencies for professional work. The survey was conducted in the period from 2013 to 2015, two years after the respondents obtained graduate status. The research sample included 3021 respondents....
-
Gdańsk University of Technology graduates’ assessment of acquired skills and competencies for professional work – years 2017-2018
Open Research DataThe dataset includes data from the survey on the Gdańsk University of Technology graduates' from the years 2017-2018 on their assessment of acquired skills and competencies for professional work. The survey was conducted in the period from 2018 to 2020, two years after the respondents obtained graduate status. The research sample included 2909 respondents....
-
Gdańsk University of Technology graduates’ self-assessment of the use of digital skills in professional work – the year 2018
Open Research DataThe dataset includes data from the survey on the Gdańsk University of Technology graduates' from the year 2018 on their self-assessment of the use of digital skills in professional work. The survey was conducted in 2020, two years after the respondents obtained graduate status. The research sample included 1315 respondents. To summarize, the vast majority...
-
Gdańsk University of Technology graduates’ assessment of acquired skills and competencies for professional work – years 2015-2016
Open Research DataThe dataset includes data from the survey on the Gdańsk University of Technology graduates' from the years 2015-2016 on their assessment of acquired skills and competencies for professional work. The survey was conducted in the period from 2017 to 2018, two years after the respondents obtained graduate status. The research sample included 4500 respondents....
-
Gdańsk University of Technology graduates’ self-assessment of the use of digital skills in professional work – the year 2016
Open Research DataThe dataset includes data from the survey on the Gdańsk University of Technology graduates' from the year 2016 on their self-assessment of the use of digital skills in professional work. The survey was conducted in 2018, two years after the respondents obtained graduate status. The research sample included 1947 respondents. To summarize, the vast majority...
-
Jakub Szulwic dr inż.
PeopleJakub Szulwic (born 23 December 1974 in Bydgoszcz, Poland) – is an experienced, licensed Land Surveyor, specialized in construction monitoring by the use of photogrammetric methods and laser scanning technology. His specialization are geomatics and geoinformatics. He is an author about 100 publications including 50 indexed in Web of Science (H-index = 15) In 1993, He graduated from Secondary School in Tuchola, Poland on physics...
-
Dynamic load tests of piles in non-cohesive soils.
PublicationThe results of investigations of various types of piles, the analysis of dynamic tests carried out recently in Poland and the correlations between the results of dynamic and static tests of piles are presented. Przedstawiono wyniki badań nośności różnych rodzajów pali, analizę badań dynamicznych wykonanych w Polsce w ostatnich latach oraz korelacje pomiędzy wynikami badań statycznych i dynamicznych.
-
Culturable bacteria from pesticides contaminated soils in Poland
Publication