Filters
total: 642
Search results for: OPÓR STOŻKA
-
Laboratoryjne badania oporu toczenia i temperatury opon do pojazdów specjalnych
PublicationW pracy przedstawiono wyniki laboratoryjnych badań oporu toczenia i temperatury opon do pojazdów specjalnych. Współczynnik oporu toczenia tych opon jest silnie uzależniony od ciśnienia pompowania. Po utracie nadciśnienia w oponie, gdy następuje styk wewnętrznej powierzchni bieżnika z wkładką Run-Flat, opór toczenia wzrasta około 7-8 razy w stosunku do sytuacji gdy ciśnienie pompowania jest wyregulowane do jazdy po drogach utwardzonych...
-
Influence of boundary conditions in calibration chamber
PublicationPrzedstawiono wyniki badań modelowych penetracji w komorze kalibracyjnej z zastosowaniem modeli o różnej średnicy. Badania przeprowadzono w piasku średnio zagęszczonym i zagęszczonym przy stałej składowej poziomej naprężenia i przy składowej pionowej naprężenia w gruncie do 400 kPa. Określono wpływ warunków brzegowych na uzyskane wyniki oporu podstawy/oporu stożka lub ostrza dylatometru. Wyznaczono współczynniki korekcyjne oraz...
-
The assessment of load-settlement curve for Atlas piles correlated with CPT tests
PublicationRacjonalne stosowanie pali przemieszczeniowych typu Atlas wymaga analitycznej oceny pełnej krzywej obciążenie - osiadanie. W pracy przedstawiono możliwości wykorzystania metody funkcji transformacyjnych t-z (dla pobocznicy) oraz q-z (dla podstawy) dla oceny krzywej osiadania. Jednostkowe graniczne opory na pobocznicy, tmax, oraz pod podstawą, gf, określono na podstawie metody bezpośredniej, wykorzystując opory stożka sondy, qc....
-
Badania modelowe w komorze kalibracyjnej
PublicationKrótki przegląd istniejących komór kalibracyjnych i przeprowadzanych w nich badań modelowych. Opis badań realizowanych w komorze kalibracyjnej skonstruowanej na Politechnice Gdańskiej wraz z przedstawieniem stosowanych modeli. Dyskusja na temat wpływu warunków brzegowych na wyniki badań penetracyjnych w piasku modelowym. Propozycja interpretacji oporu stożka z uwzględnieniem poprawki na wpływ warunków brzegowych. Opis modelowania...
-
Ryszard F. Sadowski dr hab. prof. uczelni
PeoplePLACE OF EMPLOYMENT: Since 2004 prof. Ryszard F. Sadowski is employed at the Faculty of Christian Philosophy (WFCh) at the Cardinal Stefan Wyszyński University in Warsaw. He is a member of the research team of the Center for Ecology and Ecophilosophy (former Institute of Ecology and Ecophilosophy) UKSW. Since 2020 prof. Sadowski is Chair of Ecophilosophy in the Institut of Philosophy at Cardinal Stefan Wyszyński University in Warsaw....
-
Tomasz Wąsowicz dr hab.
PeopleTomasz Wąsowicz's research was first related to high-resolution atomic spectroscopy and focused on measurements and analysis of the transition probabilities of the forbidden lines, the hyperfine and isotopic structure of spectral lines of heavy elements, Stark effect in the helium atom. Tomasz Wąsowicz currently studies physicochemical processes occurring during interactions of various forms of radiation with atoms and molecules...
-
Kryteria kontroli jakości zagęszczania wgłębnego gruntów niespoistych
PublicationEtapy kontroli jakości procesu zagęszczania wgłębnego gruntów niespoistych. Ocena przydatności danego gruntu do zagęszczania, wstępny dobór parametrów zagęszczania oraz ich weryfikacja na poletkach doświadczalnych, obserwacja osiadań i badania sprawdzające w postaci sondowań statycznych metodą CPTU, badań dylatometrycznych DMT, badań presjometrycznych PMT oraz sondowań dynamicznych DPT. Dyskusja kryteriów kontroli jakości zagęszczania...
-
Olgun Aydin dr
PeopleOlgun Aydin finished his PhD by publishing a thesis about Deep Neural Networks. He works as a Principal Machine Learning Engineer in Nike, and works as Assistant Professor in Gdansk University of Technology in Poland. Dr. Aydin is part of editorial board of "Journal of Artificial Intelligence and Data Science" Dr. Aydin served as Vice-Chairman of Why R? Foundation and is member of Polish Artificial Intelligence Society. Olgun is...
-
Modelowanie oporu poprzecznego w torze kolejowym przy wykorzystaniu badań doświadczalnych
PublicationOpór poprzeczny w torze kolejowym jest jednym z najważniejszych czynników decydujących o jego stateczności w płaszczyźnie poziomej. Utrata tej stateczności, zwana wyboczeniem toru, może stanowić bezpośrednią przyczynę katastrofy kolejowej, zwłaszcza, gdy proces ten nastąpi pod jadącym pojazdem szynowym. Celem referatu jest przedstawienie przeprowadzonych badań nad oporem poprzecznym oraz omówienie sposobu modelowania toru bezstykowego...
-
Hydrodynamical loads on a floating dock towed in sea conditions
PublicationPrzedstawiono i analizowano charakterystyki amplitudowe (RAO) oraz prognozy krótko i długoterminowe hydrodynamicznych reakcji doku pływającego holowanego w warunkach morskich na akwenach Bałtyku i Morza Północnego. Przedmiotem badań były: nurzania i kołysania wzdłużne, ciśnienia dynamiczne indukowane w różnych częściach dna doku, pionowy moment gnący i opór doku holowanego na falach czołowych. Charakterystyki RAO rozpatrywanych...
-
Influence of ozonation and biodegradation on toxicity of industrial textile wastewater
Publication -
Storia della storiografia-Histoire de l'Historiographie-History of Historiography-Geschichte der Geschichtsschreibung
Journals -
Annali della Scuola Normale Superiore di Pisa. Lettere, storia e filosofia
Journals -
PHYSIS. Rivista internazionale di storia della scienza/International Journal for the History of Science
Journals -
Patryk Topór
People -
FE-calculations of stress distribution under prismatic and conical sandpiles within hypoplasticity.
PublicationW artykule przedstawiono wyniki numerycznej rozkładu naprężeń pod pryzmatycznymi i stożkowymi stosami piasku w ramach mikropolarnej hipoplastyczności. Wyniki pokazują, że rozkład naprężeń zależy od sposobu napełnienia stożku piaskiem. W niektórych przypadkach, maksymalne naprężenie nie występuje w środku stosu piasku.
-
FE-calculations of stress distribution under prismatic and conical sandpiles within hypoplasticity
PublicationW artykule przedstawiono wyniki numerycznej rozkładu naprężeń pod pryzmatycznymi i stożkowymi stosami piasku w ramach mikropolarnej hipoplastyczności. Wyniki pokazują, że rozkład naprężeń zależy od sposobu napełnienia stożku piaskiem. W niektórych przypadkach, maksymalne naprężenie nie występuje w środku stosu piasku.
-
Information based integration for complex systems. W: Knowledge and infor-mation technology management in the 21st century organizations. Ed. A. Gu- nasekaran, O. Khalil, M.R. Syed. London: Idea**2002 s. 89-104 Informacyjna integracja systemów złożonych.
PublicationW rozdziale zaproponowano strukturę inteligentnego systemu wspomagania pro-cesu integracji dla złożonych systemów wytwarzania. System wspomagania opar-to na bazie wiedzy, w której wiedza modelowana jest regulami produkcji. Zbu-dowano również iteracyjny algorytm integracji. Samą ideę integracji opartona przepływach informacyjnych.
-
Green aspects of techniques for the determination of currently used pesticides in environmental samples
PublicationPesticides are among the most dangerous environmental pollutants because of their stability, mobility and long-term effects on living organisms. Their presence in the environment is a particular danger. It is therefore crucial to monitor pesticide residues using all available analytical methods. The analysis of environmental samples for the presence of pesticides is very difficult: the processes involved in sample preparation are...
-
The balanced scorecard method applying in small and medium enterprise management
PublicationAutorzy podejmują dyskusję z poglądem, że Strategiczna Karta Wyników jako metoda zarządzania strategicznego przedsiębiorstwem powinna raczej być stosowana w sektorze dużych przedsiębiorstw, niż małych i średnich. Wskazują na istotne trudności związane z wdrażaniem BSC w aspektach: kosztów, czasochłonności, nadzwyczajnego wysiłku organizacji, nowego spojrzenia na komunikację w dół struktury, dalekiego horyzontu planowania, sceptycyzmu...
-
Towards evaluation of the Second Generation Intact Stability Criteria - examination of a fishing vessel vulnerability to surf-riding, based on historical capsizing
PublicationThe Second Generation Intact Stability Criteria (SGISC) are the latest achievements in the field of intact ship stability assessment. The criteria are the result of massive international cooperative efforts and extensive research that lasted more than 15 years. Even though they are based on a solid scientific foundation, the trial period has commenced to collect user experience and further validation. One of possible approaches...
-
A note on mixed tree coloring
PublicationZaproponowano liniowy algorytm dla problemu kolorowania mieszanego w drzewach, uzyskując tym samym poprawę w stosunku do algorytmu o złożoności O(n^2) podanego w pracy [P. Hansen, J. Kuplinsky, D. de Werra, Mixed graph colorings, Math. Methods Oper. Res. 45 (1997) 145-160].
-
Wyznaczanie położenia trójwymiarowego sita w przestrzeni roboczej robota
PublicationSystemy wizyjne są coraz częściej stosowane w różnego rodzaju zrobotyzowanych stanowiskach produkcyjnych do sterowania, nadzorowania oraz kontroli pracy robotów spawających. Niniejsza praca opisuje dalszy rozwój systemu wizyjnego powstałego w firmie AIC w Gdyni, którego zadaniem jest integracja danych otrzymywanych z obrazu uzyskanego z kamery oraz pochodzących z laserowego czujnika odległości. Przedstawiono sposób dopasowania...
-
Ionophores in polymeric membranes for selective ion recognition:impedance studies
PublicationW pracy badano dwa typy elektrod: membranowe elektrody jonoselektywne (ISE) oraz elektrody nowego typu all-solid-state (AAS). Elektrody AAS zawierają przewodzącą warstwę polimerową na węglu szklistym lub platynie, na który nałożona jest membrana zawierająca jonofor. Do badań użyto dwa jonofory: p-tert-butylokaliks[4]aren-korona-4 (L1) selektywnie kompleksująca jony Na+ oraz kaliks[4]aren-korona-6 (L2) selektywnie kompleksująca...
-
Podstawy teoretyczne zjawisk wibroakustycznych występujących na przejazdach kolejowo - drogowych
PublicationPoziom zjawisk wibroakustycznych generowanych przez pojazdy samochodowe i kolejowe do środowiska jest zależny od wielu czynników. Są nimi np.: typ/rodzaj opon i nawierzchni, opór aerodynamiczny, konstrukcja pojazdu i jego stan techniczny. Dodatkowo impulsy dźwiękowe mogą pochodzić od uderzeń opon w znajdujące się na drodze przeszkody i infrastrukturę drogową. Do infrastruktury drogowej mającej wpływ na poziom emitowanych zjawisk...
-
Nośność graniczna pali Vibro obciążonych osiowo na podstawie próbnych obciążeń statycznych i wyników sondowania CPT.
PublicationW odniesieniu od obecnych trendów optymalizacji w projektowaniu obiektów inżynierskich, dąży się do określania rzeczywistych wartości współoddziaływać podłoża gruntowego i konstrukcji. Pale Vibro, należą do grupy pali przemieszczeniowych z poszerzoną podstawą, charakteryzują się bardzo dużą nośnością, szczególnie w gruntach niespoistych. Wyniki próbnych obciążeń statycznych wskazują, że nośność pali Vibro jest znacznie większa...
-
Notizie da Palazzo Albani: rivista annuale di storia e teoria delle arti
Journals -
Determination of the bearing capacity of pile foundations based on CPT test results
PublicationAnalityczne określanie pełnej krzywej obciążenie - osiadanie na podstawie parametrów geotechnicznych wciąż stanowi bardzo trudne zadanie naukowe i inżynierskie. W pracy przedstawiono metodę bezpośredniego wykorzystania oporów na stożku sondy statycznej do określania pełnej krzywej osiadania dla pali Vibro-Fundex. W sumie jako materiał weryfikacyjny wykorzystano 94 próbne obciążenia statyczne pali.
-
Teoria punktów stałych [2022/2023] (Matematyka, WFTiMS)
e-Learning CoursesTeoria punktów stałych WFTIMS, Matematyka
-
Compaction control at Gdynia Port with CPTU and DMT
PublicationOpis realizacji zagęszczenia wgłębnego nawodnionych piasków. Kontrola wykonanych prac z zastosowaniem sondowań statycznych i badań dylatometrycznych. Porównanie wyników przed i po wykonaniu vibroflotacji. Stwierdzono wyraźny przyrost oporu na stożku sondy statycznej oraz wartości modułu odkształcenia w zagęszczanej warstwie.Badanie dylatometryczne było bardziej wrażliwe na zmianę stanu gruntu po zagęszczeniu niż sondowanie statyczne.
-
Industry-level analysis of COVID-19’s impact in emerging markets – evidence from Pakistan
PublicationPurpose – The main purpose of this study is to evaluate COVID-19’s impact on the emerging stock markets. Design/methodology/approach – To evaluate the influence of COVID-19, this study uses a novel method of event study methodology to measure the impact of COVID-19 on emerging stock markets. The research’s sample includes a total of 79 firms from 26 industries that are included in the KSE-100 Index from the Pakistan Stock Exchange....
-
Wewnętrzne trudności strategicznej karty wyników
PublicationAutorzy podejmują w artykule dyskusję z powszechnie wyznawanym poglądem, że Strategiczna Karta Wyników jako metoda zarządzania strategicznego przedsiębiorstwem powinna raczej być stosowana w sektorze dużych przedsiębiorstw, niż małych i średnich. Aby to uczynić, w pierwszej części poniższego tekstu, wskazują na istotne trudności związane z wdrażaniem BSC w aspektach: kosztów, czasochłonności, nadzwyczajnego wysiłku organizacji,...
-
Wybrane zagadnienia projektowania mikrostrugowych wymienników ciepła
PublicationW monografii omówiono wybrane zagadnienia intensyfikacji wymiany ciepła przy zastosowaniu oryginalnej technologii mikrostrugowej. Technologia ta jest pozytywnie postrzegana w aspekcie wysokowydajnych wymienników typu rekuperator, ponieważ odpowiednio uformowana struga płynu może lokalnie rozbić warstwę przyścienną na powierzchni przegrody w wymienniku, redukując opór cieplny przejmowania ciepła między płynem a powierzchnią tej...
-
PROGNOZOWANIE MAKSYMALNYCH GRANICZNYCH WARTOŚCI PRĘDKOŚCI POSUWU DLA PROCESU PRZECINANIA DREWNA NA PILARKACH RAMOWYCH
PublicationDo szacowania efektów energetycznych (moc skrawania, siła skrawania), w klasycznym podejściu, przy przecinaniu drewna piłami wykorzystuje się w obliczeniach opór właciwy skrawania, który w przypadku drewna jest funkcją wielu mniej lub bardziej istotnych czynników. Innym podejściem jest zastosowanie modelu bazującego na mechanice pękania, w którym bierze się pod uwagę oprócz wytrzymałości drewna, warunki tarcia, a także właciwość...
-
Protokoły drzewa opinającego - ataki i metody obrony
PublicationW pracy przedstawiono sposoby ataków na sieci wykorzystujące realizacje drzewa opinającego STP (IEEE 802.1d i IEEE 802.1w a także modyfikacji STP wprowadzonych przez Cisco) oraz znane metody obrony przed atakami na STP. Zaproponowano także nową koncepcje obrony przed atakami mechanizmu STP wykorzystującą pole flags ramek BPDU.
-
Współtworzenie tekstu narracyjnego przez dziecko i osobę dorosłą w zespole Pradera-Williego i zespole Downa. Studia dwóch przypadków
Publication -
Port knocking - alternatywne rozwiązania
PublicationOmówiono techniki pukania w porty (ang. Port Knocking). Zaproponowano nowe wersje mechanizmu oparte o wykonanie sekwencji puknięć wieloma pakietami w jeden port: pukanie pakietami o różnej długości, przy czym długości te stanowiłyby sekwencję kodową, oraz pukanie, w którym sekwencją kodową są odcinki czasu pomiędzy pojawianiem się na porcie kolejnych pakietów. Rozważono możliwości zastosowania tego typu port knockingu i zaproponowano...
-
One Year Evaluation of Material Properties Changes of Polylactide Parts in Various Hydrolytic Degradation Conditions
PublicationBiodegradable biocompatible materials are widely used in medical applications. Determining the possibility of using biodegradable materials depends on determining the changes in their parameters over time due to degradation. The current scientific research on biodegradable materials has presented results based on research methods characterized by the different geometry and cross-section size of the specimen, type of degradation...
-
Biomechanical properties of 3D-printed bone models
PublicationBone lesions resulting from large traumas or cancer resections can be successfully treated by directly using synthetic materials or in combination with tissue engineering methods (hybrid). Synthetic or hybrid materials combined with bone tissue’s natural ability for regeneration and biological adaptation to the directions of loading, allow for full recovery of its biological functions. Increasing interest in new production methods...
-
Three-Dimensional Printing of Bone Models
PublicationThe trabecular bone occurs, for example, in the femoral heads. Understanding the phenomenon of bone tissue degeneration can be the basis for the possibility of looking for alternative methods of surgical treatment of bone loss. The paper presents the results of the trabecular bone model, which was produced in additive manufacturing method with fused filament fabrication technology. The verification of the mechanical behavior of...
-
Mechanical Properties of 3D Printed Parts and Their Injection Molded Alternatives Subjected to Environmental Aging
PublicationAdditive manufacturing is the technology used in medical, industrial, or lifestyle applications. The scientific literature include works reporting various manufacturing parameters’ influence on changes in additive manufacturing components’ mechanical behavior, especially with fused filament fabrication (FFF). The changes in mechanical strength and toughness of FFF compared to injection molding parts were studied. In the study,...
-
A note on the affective computing systems and machines: a classification and appraisal
PublicationAffective computing (AfC) is a continuously growing multidisciplinary field, spanning areas from artificial intelligence, throughout engineering, psychology, education, cognitive science, to sociology. Therefore, many studies have been devoted to the aim of addressing numerous issues, regarding different facets of AfC solutions. However, there is a lack of classification of the AfC systems. This study aims to fill this gap by reviewing...
-
Experimental study on the effect of selected sterilization methods on mechanical properties of polylactide FFF specimens
PublicationPurpose: Biodegradable polymers are widely used in personalized medical devices or scaffolds for tissue engineering. The manufacturing process should be finished with sterilization procedure. However, it is not clear how the different sterilization methods have an impact on the mechanical strength of the three-dimensional (3D)-printed parts, such as bone models or personalized mechanical devices. This paper aims to present the...
-
Percepcja jakości usług noclegowych w uwarunkowaniach regionalnych Pomorza i Lubelszczyzny
PublicationW niniejszym rozdziale podjęto próbę przedstawienia podstawowych kryteriów postrzegania jakości usług hotelarskich i parahotelarskich, w konsekwencji determinujących decyzję wyboru i zakupu konkretnej usługi z uwzględniniem specyfki regionalnej.
-
Kryteria jakości usług turystycznych z uwzględnieiem specyfiki regionalnej
PublicationW niniejszym rozdziale zaprezentowano podstawowe aspekty jakości usług turystycznych. Autorzy zdefiniowali kluczowe obszary tego typu usług oraz na podstawie przeprowadzonych badań zaprezentowali kluczowe czynniki wpływające na postrzeganie jakości usług turystycznych przez klientów. Wszelkie analizy zawarte w niniejszym rozdziale wiążą się z identyfikacją kryteriów jakości usługi turystycznej z uwzględnieniem specyfiki regionalnej.
-
Bridge Ergonomic Design: A Review
PublicationHuman error remains the most common cause of marine incidents and it is worth emphasizing that navigator’s performance is directly affected by ergonomic factors on the bridge. Studies regarding influence of bridge design and work environment on the operator are rare, thus the main purpose of this paper is to fill in this gap. Documents issued by recognized organizations, research publications and additional sources were reviewed...
-
Application of Ion Exchangers in Speciation and Fractionation of Elements in Food and Beverages
Publication -
Interference-Free Determination of Trace Copper in Freshly Ripened Honeys by Flame Atomic Absorption Spectrometry Following a Preconcentration by Solid-Phase Extraction and a Two-Step Elution Process
Publication -
Solid phase extraction and sequential elution for pre-concentration of traces of Mn and Zn in analysis of honey by flame atomic absorption spectrometry
Publication -
OVERALL SET OF BANDSAW TEETH VERSUS METHODS OF MEASUREMENTS
PublicationThis article deals with the impact of the manual methods of measurement on the overall set measurement results. It describes the results of the measurement of bandsaw teeth kerf with the use of a micrometer and a digital calliper. It is commonly known that the cutting process causes the wear of cutting tools. The wear of the cutting edge depends on the cutting conditions as well as on the mechanical properties of the processed...