Filters
total: 4757
-
Catalog
- Publications 3220 available results
- Journals 12 available results
- Publishing Houses 1 available results
- People 42 available results
- Inventions 14 available results
- Projects 5 available results
- Laboratories 3 available results
- Research Teams 1 available results
- Research Equipment 3 available results
- e-Learning Courses 25 available results
- Events 2 available results
- Open Research Data 1429 available results
displaying 1000 best results Help
Search results for: UJEMNE TEMPERATURY
-
The influence of solution annealing temperature on the properties of Lean Duplex 2101 welded joints in tubes
PublicationThe article presents a technology of TIG longitudinal welding without filler material (142) of heat exchanger tubes made of Lean Duplex 2101. The results of studies on the effect of heat treatment (solution annealing) on tensile strength, plasticity, delta ferrite and the structure of smooth tubes are shown. It was found, that the change in solution annealing temperature across the tested range has an impact on mechanical properties...
-
High-temperature heat pumps – potential technology for heat recovery and production of process heat
PublicationIn the paper, the high temperature vapour compressor based heat pump with a selection of working fluids, both perspective and ecological ones, is considered. Such system is not yet commercially available on the market and in author’s opinion it has significant potential for various applications. In the presented analysis it was assumed that the heat source has a temperature of 50oC and the temperature lift is 60, 80 and 100K respectively....
-
High-temperature heat pumps – new devices for heat recovery and production of technological steam
PublicationIn the paper, the original high temperature compressor based heat pump with a dry working fluid, i.e. the one in which the slope of saturated vapour line is positive, was presented. The objective of the paper is to investigate the possibility of preparation of technological steam with tempperature 120 C from the waste heat resource at temperature of 50 C. Single comppression cycles as well as cascade systems have been considered...
-
The hydration of selected biologically relevant molecules – the temperature effect on apparent molar volume and compression
PublicationThe densities and sound velocities at T = (288.15, 293.15, 298.15, 303.15 and 308.15) K were measured for aqueous solutions of glycine, trimethylamine-N-oxide, taurine and N-methylacetamide. From these data, the apparent molar volumes, V the apparent molar isentropic compressions, KS,, and the Passynski hydration numbers of solutes were determined. The concentration dependencies of the calculated quantities, their limiting values...
-
(Vapour + liquid) equilibrium in (n,n-dimethylacetamide + ethanol + water) at the temperature 313.15 K
PublicationW pracy prezentowane są pomiary całkowitej prężności pary dla tytułowego układu trójskładnikowego oraz dla składowych układów binarnych. Uzyskane w pracy wyniki porównane zostały z wcześniejszymi danymi dla podobnych układów. Znaleziono w przybliżeniu liniową zależność pomiędzy wartościami nadmiarowej entalpii swobodnej Gibbsa a objętością molową amidu, spełnianą w układach dwuskładnikowych: amid + alkohol alifatyczny.
-
Exchange of radiation in high temperature air combustion furnaces by application of the transfer configuration factors
PublicationW artykule przedstawiono metodę obliczeń pasmowej radiacyjnej wymiany ciepła w układzie otwartym z gazem iztermicznym za pomocą uogólnionych współczynników konfiguracji. Metoda może być użyta do obliczeń wymiany ciepła w piecach z technologią High Temperature Air Combustion gdzie występuje prawie jednorodna temperatura. Podano przykład obliczeniowy.
-
Influence of high temperature air-steam mixture application on time wood drying process
PublicationThe results of influence gas-steam mixture drying process on time wood drying process are presented. Wood species, namely oak (Quercus L.), beech (Fagus L.), pine (Pinus L.) and spruce (Picea K.) from the northern part of Pomerania region in Poland, were subject of air-steam mixture drying process. Main focus of those tests was to shorten the time of drying process and afterward to check properties of wood.
-
The effect of calcination temperature on structure and photocatalytic properties of Au/Pd nanoparticles supported on TiO2
PublicationBimetallic nanoparticles, composed of two different metal elements, can exhibit peculiar electronic, optical, and catalytic or photocatalytic properties that are absent in the corresponding monometallic nanoparticles. We show the effect of calcination temperature (from 350 to 700°C) on the structure and the photocatalytic properties of Au/Pd-modified TiO2. The composition of the bimetallic Au/Pd nanoparticles in relation to their...
-
Diagnostic tolerances' evaluation method of the start-up exhaust temperature of a naval gas turbine
PublicationThe conducted investigations aimed to elaborate the method of marking diagnostic tolerances of the exhaust temperature of a gas turbine observed during engine's start-up process. The diagnostic tolerances were determined by means of statistical inference by creating the hypothesis about a normal distribution of the start-up exhaust temperature's dispersion in the initial operation moment, which was subsequently verified applying...
-
A new procedure for the determination of distillation temperature distribution of high-boiling petroleum products and fractions
PublicationThe distribution of distillation temperatures of liquid and semi-fluid products, including petroleum fractions and products, is an important process and practical parameter. It provides information on properties of crude oil and content of particular fractions, classified on the basis of their boiling points, as well as the optimum conditions of atmospheric or vacuum distillation. At present, the distribution of distillation temperatures...
-
Combustion of low calorific fuel at room and high temperature and at different oxygen content in the oxidizer
PublicationPraca przedstawia wyniki badań spalania paliwa niskokalorycznego powstałego w wyniku gazyfikacji biomasy. Badania prowadzono w temperaturze pokojowej oraz w warunkach typowych dla technologii HiTAC, tj. w temperaturze powyżej samozapłonu paliwa i przy różnej zawartości tlenu w utleniaczu. Wykazano możliwość wykorzystania technologii HiTAC do spalania takich paliw.
-
Multimodal analysis of traction forces and the temperature dynamics of living cells with a diamond-embedded substrate
PublicationCells and tissues are constantly exposed to chemical and physical signals that regulate physiological and pathological processes. This study explores the integration of two biophysical methods: traction force microscopy (TFM) and optically detected magnetic resonance (ODMR) to concurrently assess cellular traction forces and the local relative temperature. We present a novel elastic substrate with embedded nitrogen-vacancy microdiamonds...
-
Circumferential temperature distribution during pool boiling of R 141b onhorizontal modified tubes.
PublicationZaproponowano własną bierną, metodę intensyfikacji przejmowania ciepła w obszarze górnej tworzącej rurki w celu zminimalizowania obwodowego rozkładu temperatury. Metoda polega na naniesieniu aluminiowej warstwy porowatej tylko na części powierzchni rurki - właśnie w obszarze górnej tworzącej.
-
Modeling of low calorific gas burning in a deficient oxygen environment and high-temperature oxidizer
PublicationThe experimental research will be performed using the experimental facility with a combustion chamber. The oxygen concentration in combustion oxidizers will be varied from 21% by volume (normal) air to 2%. The test combustion chamber will be fed with propane or methane as the reference fuel, then with low calorific fuels as test gases obtained by mixing various combustible components, e.g. H2, CH4, CO, and neutral gases, e.g. N2,...
-
Effect of austempering temperature on microstructure and cyclic deformation behaviour of multiphase low-carbon steel
PublicationThis paper examined the cyclic deformation behaviour of multiphase low-carbon steel that was subjected to austempering heat treatments at four temperatures (190 °C, 230 °C, 275 °C, and 315 °C) below the martensite start temperature (Ms = 353 °C). The tests were conducted at room temperature, under fully reversed strain-controlled conditions, with strain amplitudes in the range 0.5–1.0%. The microstructure was observed by transmission...
-
Measurement of temperature-dependent viscosity and thermal conductivity of alumina and titania thermal oil nanofluids
PublicationThe results of simultaneous measurements of dynamic viscosity, thermal conductivity, electrical conductivity and pH of two nanofluids, i.e. thermal oil/Al2O3 and thermal oil/TiO2 are presented. Thermal oil was selected as a base liquid because of possible application in ORC systems as an intermediate heating agent. Nanoparticles were tested at the concentration of 0.1%, 1% and 5% by weight within temperature range from 20°C to...
-
Identification of Bodner-Partom Viscoplastic Model Parameters for Some Aluminum Alloys at Elevated Temperature
PublicationThe paper presents the identification process of inelastic (viscoplastic) properties for two aluminum alloys at a temperature of 120°C. The material parameters are calculated on the basis of uniaxial tension tests. Twelve tests at elevated temperature for each alloy have been performed—three tests for four different strain rates. The main purpose of the paper is to identify the Bodner-Partom viscoplastic model parameters for two...
-
A new viscoelastic method of calculation of low-temperature thermal stresses in asphalt layers of pavements
PublicationThe paper presents a new method of calculation of thermal stresses in asphalt layers of pavements induced by cooling or heating. The method, developed by the author, is based on the analytical solution for the linear viscoelastic Burgers model extended numerically for the case of asphalt layers whose rheological parameters are strongly dependent on temperature. The coefficient of thermal expansion and Poisson’s ratio may optionally...
-
Analytical method for calculation of heat source temperature drop for the Organic Rankine Cycle application
PublicationIn the paper presented are considerations on the cooperation of the limited capacity heat source with the Organic Rankine Cycle unit. Usually the heat source providing thermal energy to the Organic Rankine Cycle (ORC) may have twofold characteristics. It can be in the form of a single phase fluid, i.e. as hot exhaust gas or hot liquid, or in some cases it may be available as a phase changing fluid, as for example, technological...
-
Parameters’ Identification of Perzyna and Chaboche Viscoplastic Models for Aluminum Alloy at Temperature of 120◦C
PublicationThe main purpose of this paper is the parameters identification of the Perzyna and the Chaboche models for the aluminum alloy at elevated temperature. The additional purpose is comparison of the results for these viscoplastic models. The results have been verified by the numerical simulation of the laboratory tests. The material parameters have been calculated on the basis of the uniaxial tension test. The determination of the...
-
Numerical Investigation of Nuclear Reactor Kinetic and Heat Transfer Fractional Model with Temperature Feedback
PublicationAbstract—In the paper, the numerical results concerning the kinetics and proposed heat exchange models in nuclear reactor based on fractional calculus are presented for typical inputs. Two fractional models are proposed and compared with the model based on ordinary derivative. The first fractional model is based on one of the generalized Cattaneo equations. The second one is based on replacing the ordinary to fractional order of...
-
High temperature monoclinic-to-tetragonal phase transition in magnesium doped lanthanum ortho-niobate
PublicationMagnesium doped lanthanum ortho-niobate (La0.98Mg0.02NbO4) was prepared by the molten salt synthesis method. X-ray diffraction and dilatometry methods were used to study high temperature behavior of the ceramic material. Special attention was paid to the phase transition between the monoclinic and tetragonal phases. The values of spontaneous strain on the basis of unit cell parameter, obtained by Rietveld refinement, have been...
-
MEASUREMENT OF TEMPERATURE-DEPENDENT VISCOSITY AND THERMAL CONDUCTIVITY OF ALUMINA AND TITANIA THERMAL OIL NANOFLUIDS
PublicationIn this study results of simultaneous measurements of dynamic viscosity, thermal conductivity, electrical conductivity and pH of two nanofluids, i.e. thermal oil/Al2O3 and thermal oil/TiO2 are presented. Thermal oil is selected as a base liquid because of possible application in ORC systems as an intermediate heating agent. Nanoparticles were tested at the concentration of 0.1%, 1% and 5% by weight within temperature range from...
-
Improving the CPX method by specifying reference tyres and including corrections for rubber hardnes and temperature
PublicationRecently completed work in the EU project ROSANNE and in working group ISO/TC43/SC1/WG33 has allowed substantial improvements to measurements made by the Close-Proximity (CPX) method, intended for measurement of noise properties of road surfaces.The paper summarizes the experimental work and describes the conclusions and implementation in ISO/FDIS 11819-2 (CPX method) and in the supporting ISO (draft) Technical Specifications 11819-3...
-
Influence of electropolymerization temperature on corrosion, morphological and electrical properties of PPy doped with salicylate on iron
PublicationIn this work, the influence of the electropolymerization temperature on corrosion, morphological and electrical properties of polypyrrole (PPy) film is studied. Polypyrrole is electrochemically synthesized on iron in the presence of sodium salicylate. The X-ray diffraction and scanning electron microscopy are performed in order to study the structure and morphology of electrodeposited PPy. The electroactive surface area, corrosion...
-
Temperature influence on tyre/road noise on poroelastic road surface based on laboratory measurements
PublicationThe temperature effect on measured tyre/road noise is very important phenomena as it may lead to significant errors in measurement results due to substantial influence of this parameter on the obtained values. It depends mainly on the particular tyre-road combination. It is different for dense and porous as well as for bituminous and cement concrete pavements. It differs also depending on tested tyre. The correction procedure for...
-
Mechanism of Reduced Sintering Temperature of Al2O3–ZrO2 Nanocomposites Obtained by Microwave Hydrothermal Synthesis
PublicationA novel method to obtain Al2O3–ZrO2 nanocomposites is presented. It consists of the co-precipitation step of boehmite (AlO(OH)) and ZrO2, followed by microwave hydrothermal treatment at 270 ◦ C and 60 MPa, and by calcination at 600 ◦ C. Using this method, we obtained two nanocomposites: Al2O3–20 wt % ZrO2 and Al2O3–40 wt % ZrO2. Nanocomposites were characterized by Fourier transformed infrared spectroscopy, Raman spectroscopy,...
-
High temperature air/steam gasification of biomass in view of hydrogen rich gas production.
PublicationArtykuł przedstawia opis nowej i zaawansowanej metody konwersji termochemicznej biomasy i miejskich odpadów stałych w paliwo gazowe, bogate w wodór. W porównaniu z tradycyjnym procesem gazyfikacji, w metodzie tej wykorzystuje się powietrze/parę wodną przegrzane do wysokiej temperatury (powyżej 1300 st. C). Przegrzanie powietrza lub pary wodnej odbywa się z zastosowaniem ceramicznego przegrzewacza wysokotemperaturowego. W celu...
-
(Vapour and liquid) equilibrium in (N,N-dimethylacetamide+methanol+water) at the temperature 313.15 K.
PublicationPraca zawiera wyniki pomiarów całkowitej prężności pary dla tytułowego układu trójskładnikowego oraz dla ''składowych'' układów binarnych. Wyniki obliczeń nadmiarowej energii swobodnej mieszania dla układów (N,N-dimetyloaceta-mid+woda) i (N,N-dimetyloacetamid+metanol) porównane zostały z rezultatami uzyskanymi wcześniej dla innych układów (amid+metanol) oraz (amid+woda). Znaleziono interesującą zależność wartości nadmiaru...
-
Hydrogen rich gas production from high temperature air/steam gasification of biomass
PublicationW pracy przedstawiono nowoczesną technikę konwersji biomasy oraz stałych odpadów komunalnych w celu produkcji paliwa gazowego bogatego w wodór. Opisany proces gazyfikacji przebiega w wysokiej temperaturze przy obniżonej koncentracji tlenu i udziale pary wodnej. Dzięki temu możliwa jest produkcja gazów palnych, w szczególności H2, który można wykorzystać do produkcji energii elektrycznej i cieplnej.
-
Wstępna ocena wpływu niektórych parametrów docierania na wzrost temperatury elementów układu wykonawczego docierarki jednotarczowej
PublicationPrzedstawiono wyniki badań rozpoznawczych procesu docierania w aspekcie wzrostu temperatury elementów układu wykonawczego docierarki jednotarczowej. Temperaturę mierzono zdalnie, wykorzystując kamerę termograficzną serii V-20 II firmy VIGO Sytem SA. Obróbkę prowadzono na docierarce Abralap 380. Analizowano wpływ podstawowych parametrów docierania: czasu, prędkości i nacisków jednostkowych. Docierano stal w stanie miękkim mikroziarnami...
-
Analiza temperatury ekwiwalentnej do projektowania nawierzchni asfaltowych w Polsce z wykorzystaniem metody AASHTO 2004
PublicationW artykule przedstawiono analizę temperatury ekwiwalentnej obliczanej w oparciu o kryterium spękań zmęczeniowych warstw asfaltowych z metody AASHTO 2004 oraz kryterium deformacji strukturalnych Instytutu Asfaltowego. Do obliczeń przyjęto konstrukcję nawierzchni KR5 oraz wykorzystano dane temperaturowe z 50 stacji meteorologicznych z okresu 30 lat od roku 1989 do roku 2019 włącznie udostępnione przez Instytut Meteorologii i Gospodarki...
-
Analiza lepkosprężysta zachowania się konstrukcji nawierzchni drogowej w zależności od temperatury i warunków obciążenia
PublicationPrzedmiotem artykułu jest analiza lepkosprężysta podatnej konstrukcji nawierzchni drogowej w warunkach wysokich temperatur. W analizie wykorzystano model lepkosprężystości Burgersa warstw asfaltowych. Parametry modelu wyznaczono w oparciu o wyniki badań mieszanek mineralno-asfaltowych pod obciążeniem powtarzalnym. Analizowano wpływ rozkładu temperatury, ciężaru koła i prędkości ruchu na ugięcia powierzchni jezdni i odkształcenia...
-
Wpływ temperatury przesycania na właściwości złączy spawanych rur ze stali typu Lean Duplex 2101
PublicationW artykule przedstawiono wpływ temperatury przesycania w powiązaniu z technologią spawania wzdłużnego metodą TIG (142) rurek stosowanych w budowie wy-mienników ciepła ze stali Lean Duplex 2101. Przedstawiono wyniki badań wytrzymałości na rozciąganie, prób technologicznych określających właściwości plastyczne, makro- i mikro-skopowe oraz pomiaru zawartości ferrytu delta metodą magnetyczną. Ustalono, że zmiana temperatury przesycania...
-
Ocena wpływu temperatury powietrza atmosferycznego na efekty pracy zespołu turbiny gazowej w sezonie letnim.
PublicationPrzeprowadzono analizę wpływu zmiany temperatury powietrza atmosferycznego na pracę zespołu turbiny gazowej, tzn. na zmianę mocy sprężarki oraz wzrost zużycia paliwa gazowego.
-
Hydroliza materiału lignocelulozowego w warunkach podwyższonego ciśnienia i temperatury połączona z gwałtownym rozprężaniem wody
PublicationWykorzystanie biomasy na cele energetyczne jako alternatywy dla paliw kopalnych jest atrakcyjne zarówno z powodów ekonomicznych jak i ekologicznych. Jedną z metod umożliwiających przygotowanie materiału lignocelulozowego do produkcji paliw takich jak etanol bądź metan, w procesie fermentacji, jest hydroliza.
-
Wpływ temperatury na bilans węgla, wodoru oraz azotu w produktach pirolizy odpadowych zrębek brzozowych
Publicationiroliza jest beztlenowym endotermicznym procesem rozkładu pod wpływem wysokiej temperatury. Proces ten stosuje się w celu otrzymania substancji chemicznych lub konwersji paliw. W wyniku beztlenowego rozkładu drewna otrzymuje się produkty zgrupowane w trzech stanach skupienia: stałym, ciekłym oraz gazowym [Kardaś i in., 2014]. Udziały poszczególnych produktów pirolizy mogą być modyfikowane poprzez zmianę parametrów prowadzenia procesu....
-
Dark current characteristics of single crystalline silicon solar cells.
PublicationW pracy przedstawiono wpływ szkodliwych rezystancji na parametry pracy krzemowych ogniw fotowoltaicznych. W tym celu wyznaczono ciemne charakterystyki prądowo-napięciowe. W celu opisu własności elektrycznych ogniw zastosowano model jedno- i dwu-diodowy. Wyznaczono współczynniki nieidealności charakterystyki i rezystancję szeregową w całym zakresie temperatur pracy ogniw fotowoltaicznych dla zastosowań naziemnych. Wyznaczona za...
-
Theoretical prediction of enthalpies and temperatures of sublimation of organochlorine compounds including pesticides
Publication -
Evaluation of porous 430L stainless steel for SOFC operation at intermediate temperatures
PublicationW pracy przedstawiono badania porowatej stali nierdzewnej typu 430L do zastosowań w tlenkowych ogniwach paliwowych jako podłoża. Podłoża były poddawane utlenianiu w powietrzu oraz w wodorze i analizowane z wykorzystaniem mikroskopu elektronowego, dyfrakcji rentgenowskiej i termograwimetrii cyklicznej.
-
Achieving Efficient and Stable Deammonification at Low Temperatures—Experimental and Modeling Studies
PublicationThe short-term effects of temperature on deammonification sludge were evaluated in a laboratory-scale sequencing batch reactor (SBR). Mathematical modeling was used for further evaluations of different intermittent aeration strategies for achieving high and stable deammonification performance at decreasing temperatures. As for the biomass cultivated at high temperatures (e.g., 30 C), a higher temperature dependency (the adjusted...
-
Assessment of reformer tubes degradation during longterm service at elevated temperatures
Publication -
Modelling of Asphalt Mixes under Long Time Creep at Low Temperatures
PublicationProper description of asphalt mixtures behavior under long time load is one of the most important factors in analyses of strain and stress relations at low temperatures both from traffic and environmental loads. For example different models of thermal stress accumulation require different approaches of description of asphalt concrete. But in all cases it is required to describe its behavior under long time loading, which in some...
-
RESEARCH OF HYDRAULIC PISTON PUMPS’ START-UP IN LOW AMBIENT TEMPERATURES
PublicationStarting hydraulic pumps in low ambient temperatures may cause: decreased hydraulic-mechanical efficiency, larger vibration of hydraulic installation, faster wear and more frequent damage to the elements of pumps, change of material properties of elements, increase of pressure drop. As a result of increase of resistance of cold oil flow in the suction pipe, large underpressure may be experienced, causing incomplete filling of pump...
-
Michał Ryms dr inż.
PeopleMichał Ryms, PhD, Eng. is the physicist, graduate of the Gdańsk University of Technology. PhD thesis defended at the Chemical Faculty. Since 2011 an employee at the Department of Chemical Apparatus and Theory of Machines, Chemical Faculty, Gdansk University of Technology, POLAND – now as an assistant professor. His research interests includes: improvement of energy efficiency and possibilities of new application of phase change...
-
On the critical temperature discontinuity at the theoretical bcc-fcc phase transition in compressed selenium and tellurium superconductors
Publication -
Modeling of the L and M x-ray line structures for tungsten in high-temperature tokamak plasmas
Publication -
The Influence of Ambient Temperature Changes on the Indicators of Inflammation and Oxidative Damage in Blood after Submaximal Exercise
Publication -
Spectroscopic properties of high-temperature sintered SrS:0.05%Ce3+ under high hydrostatic pressure
Publication -
Aluminide Thermal Barrier Coating for High Temperature Performance of MAR 247 Nickel Based Superalloy
Publication