Search
Faculty of Mechanical Engineering and Ship Technology
Publications
Filters
total: 2544
displaying 1000 best results Help
Catalog Publications
Year 2024
-
Research of chitosan coatings deposited by electrophoretic deposition method at various voltage and time parameters
PublicationThe aim of this research is to estimate the electrophoretic deposition main parameters, such as voltage and time duration, that will provide optimal characteristics of the surface layer. Chitosan coatings were synthesized on biomedical Ti13Zr13Nb alloys at 20 V and 30 V and with deposit times of 2min, 5 min, 10 min, and 15 min. Evaluation of the coating was performed by using Scanning Electron Microscope (SEM), Energy-Dispersive...
-
Risk Assessment at Unsignalized Intersections Based on Human-Road-Environment-Vehicle System Applying Fuzzy Logic
PublicationThe constant increase in motorization level and traffic density increases risks due to dangerous situations for road participants. Therefore, assessing the accident level of road network elements has been an urgent task over the past decades. However, existing approaches mainly rely on traffic flow parameters and account for dynamic vehicle characteristics. The research aims to design a model accounting for uncertain factors (weather...
-
Risk Assessment Due To Customs Delays In Supply Chains By Fuzzy Logic
PublicationDue to violations of existing trade relations, cargo flows between the European Union and Ukraine have been redistributed. As a result, new supply chains have been created that have increased the tension on ground transport, including road and rail. Unfortunately, this has caused significant delays when crossing the border, which has led to a greater increase in the total delivery time of goods. Therefore, to plan for effective...
-
Risk factor assessment in agricultural supply chain by fuzzy logic
PublicationSignificant uncertainty characterizes the harvest period. This aspect is due to various risks impacting agrifood supply chains. The occurrence of risks is due to hazards: technological failures, technical breakdowns, or adverse weather conditions. Hence, the operational time of the agricultural supply chain during the harvest period increases due to such risk factors. In essence, some hazards are fuzzy, and the nature of most threats...
-
Role of buttering layer composition on microstructural heterogeneity and mechanical properties of Alloy 617 and P92 steel dissimilar welded joints for future Indian AUSC program
PublicationRestrictive operating conditions (even exceeding 700 °C) of materials in advanced ultra super critical (AUSC) power plants and the need to minimize manufacturing and maintenance costs require the production of dissimilar metal welded joints (DMW). Significant differences in the physical and chemical properties of welded materials lead to phenomena that reduce the weldability of the metals used and force the search for solutions...
-
Saint-Venant torsion based on strain gradient theory
PublicationIn this study, the Saint-Venant torsion problem based on strain gradient theory is developed. A total form of Mindlin's strain gradient theory is used to acquire a general Saint-Venant torsion problem of micro-bars formulation. A new Finite Element formulation based on strain gradient elasticity theory is presented to solve the Saint-Venant torsion problem of micro-bars. Moreover, the problem is solved for both micro and macro...
-
Selected aspects of performance of organic Rankine cycles incorporated into bioenergy with carbon capture and storage using gasification of sewage sludge
PublicationThe study aims to investigate the application of the Organic Rankine Cycle (ORC) in the bioenergy with carbon capture and storage (BECCS) using gasification of sewage sludge. The tool used in the investigation is the Aspen Plus software with REFPROP property methods for calculating fluid properties. The reason for this study is that a detailed analysis of the proposed BECCS process flow diagram indicates that a certain amount of...
-
Selecting a transport and forwarding company for meeting a customer’s needs when organizing international road cargo transportation
PublicationThe object of this study is the process of planning the work of a manufacturing enterprise that needs transport and forwarding services when exporting goods to counterparties in different countries of the world. The problem being solved is predetermined by the need to devise recommendations for choosing a transport and forwarding company when serving an individual customer, based on its individual needs and conditions of cooperation. A...
-
Simulation-Based Approach to a More Efficient Handling Strategy for a Container Terminal Storage Yard: Case Study of the Baltic Hub Container Terminal
PublicationThe primary objective of this research was to implement a more efficient handling strategy in the container terminal storage yard at the Baltic Hub Container Terminal (BHCT). Following an analysis of the current logistics system associated with starboard-side mooring, an attempt was made to shift the mooring to the port side. Two routing strategies corresponding to the analysed mooring operations were tested using a developed...
-
Simulation-Based Approach to a More Efficient Handling Strategy for a Container Terminal Storage Yard: Case Study of the Baltic Hub Container Terminal
PublicationThe primary objective of this research was to implement a more efficient handling strategy in the container terminal storage yard at the Baltic Hub Container Terminal (BHCT). Following an analysis of the current logistics system associated with starboard-side mooring, an attempt was made to shift the mooring to the port side. Two routing strategies corresponding to the analysed mooring operations were tested using a developed model....
-
Sintering Parameter Investigation for Bimetallic Stainless Steel 316L/Inconel 718 Composite Printed by Dual-Nozzle Fused Deposition Modeling
PublicationFused deposition modeling (FDM) nowadays offers promising future applications for fabricating not only thermoplastic-based polymers but also composite PLA/Metal alloy materials, this capability bridges the need for metallic components in complex manufacturing processes. The research is to explore the manufacturability of multi-metal parts by printing green bodies of PLA/multi-metal objects, carrying these objects to the debinding...
-
Soft Tissue Retraction Maneuver in Cone Beam Computed Tomography Prior to Crown-Lengthening Procedure—A Technical Note
PublicationBackground: An accurate determination of the biological width and the relationship of the cemento-enamel junction with the border of the alveolar bone is crucial during a clinical crown-lengthening (CCL) procedure. The aim of this study was to present a technical note about the retraction techniques in cone beam computed tomography (CBCT) prior to CCL, highlighting the significant enhancement in procedural accuracy and predictability...
-
Storage of High-Strength Steel Flux-Cored Welding Wires in Urbanized Areas
PublicationThe condition of the consumables is a key factor determining the waste reduction in the welding processes and the quality of the welded joint. The paper presents the results of tests of four types of fux-cored wires dedicated for welding high-strength steels, stored for 1 month and 6 months in Poland in two urbanized areas: in a large seaside city (Gdańsk) and in Warsaw, located in the center of the country. The wires were subjected...
-
Strain energy density and entire fracture surface parameters relationship for LCF life prediction of additively manufactured 18Ni300 steel
PublicationIn this study, the connection between total strain energy density and fracture surface topography is investigated in additively manufactured maraging steel exposed to low-cycle fatigue loading. The specimens were fabricated using laser beam powder bed fusion (LB-PBF) and examined under fully-reversed strain-controlled setup at strain amplitudes scale from 0.3% to 1.0%. The post-mortem fracture surfaces were explored using a non-contact...
-
Study of Nanohydroxyapatite Coatings Prepared by the Electrophoretic Deposition Method at Various Voltage and Time Parameters
PublicationThe aim of the work is to compare the properties of nanohydroxyapatite coatings obtained using the electrophoretic deposition method (EDP) at 10 V, 20 V, and 30 V, and with deposit times of 2 and 5 min. The primary sedimentation was used to minimize the risk of the formation of particle agglomerates on the sample surface. Evaluation of the coating was performed by using a Scanning Electron Microscope (SEM), Energy-Dispersive Spectroscopy...
-
Study on the wear characteristics of a 3D printed tool in flat lapping of Al2O3 ceramic materials
PublicationWidespread and popular use of ceramic products in various industry sectors necessitates the search for methods of their efficient processing. Lapping technology, which enables obtaining high dimensional and shape accuracy and high surface flatness, is one of the basic methods of finishing hard and brittle technical ceramics with a porous structure. This study analyzed the characteristics and wear value of an SLS-printed abrasive...
-
Symbolic multibody models for digital-twin applications
PublicationSymbolic generation of multibody systems equations of motion appeared in the 1980s. In addition to their computational advantage over their numerical counterparts, symbolic models can be very easily and straightforwardly interfaced with a wide range of software environments and hardware devices. These two features place this approach in a pole position to participate and intervene in the design of digital twins for systems such...
-
Szlifowanie na docierarkach sposobem zmniejszenia skażenia powierzchni ziarnami ściernymi w obróbce wykończeniowej
PublicationW artykule przedstawiono szkodliwość skażenia powierzchni mikroziarnami ściernymi w procesach docierania luźnym ścierniwem żeliwa szarego oraz sferoidalnego. Omówiono technologie szlifowania powierzchni płasko-równoległych z kinematyką docierania obiegowego, jako sposób zmniejszenia skażenia powierzchni ścierniwem po obróbce wykończeniowej.
-
Szlifowanie powierzchni płasko-równoległych z kinematyką docierania
PublicationPrzedstawiono charakterystykę szlifowania powierzchni płasko-równoległych z kinematyką docierania obiegowego. Analizowano obróbkę materiałów konstrukcyjnych na docierarkach dwutarczowych. Porównano warunki i wyniki szlifowania z tradycyjnym docieraniem luźnym ścierniwem. Scharakteryzowano sposób wyrównywania powierzchni roboczych narzędzi oraz omówiono główne zalety szlifowania na docierarkach.
-
Teaching of Robot Arm Programming - Tasks with Increasing Difficulty
PublicationThe article describes education techniques using robotics. For example, educational exercises on programming the Nachi MZ04 robotic arm are presented. The exercises use a wooden railroad toy model and elements printed in additive manufacturing technology. The exercises have increasing difficulty and can be used to educate young people in high school and specialized higher engineering studies (both bachelor's and master's).
-
Techno-economic analysis of a hybrid energy system for electrification using an off-grid solar/biogas/battery system employing HOMER: A case study in Vietnam
PublicationThe electrification of off-grid /island villages is a critical step towards improving the techno-economic circumstances of rural regions and the overall general growth of the country. However, consistent supply from a single source is not possible in these areas. Thus, a hybrid renewable energy system performs better in these conditions. The research challenge now is to identify the optimal combinations of HRES from the available...
-
Temperature Measurements at Tyre Tread Rubber on Sandpaper Oscillatory Sliding Contacts Using Acicular Grindable Thermocouples
PublicationThe tribological performance of tyre–road contacts depends crucially on the contact temperature. This study investigates the reliability and accuracy of acicular grindable thermocouples possessing an original needle-shaped wearable part as applied to measuring temperature at the oscillatory sliding contact between a rubber tyre tread sample and a sandpaper. A linear oscillatory tribometer is used to imitate the sliding phase of...
-
The clamping selection method to reduce the vibration of large-size workpieces during the face milling process
PublicationThe article introduces a method for selecting the best clamping conditions to obtain vibration reduction during milling of large-size workpiece. It is based on experimental modal analysis performed for a set of assumed, fixing conditions of a considered workpiece to identify Frequency Response Functions (FRFs) for each tightening torque of the mounting screws. Simulated plots of periodically changing nominal cutting forces are...
-
The degradation mechanisms of a nanobainitic steel under cavitation erosion conditions
Publication -
The effect of elevated temperature on LCF damage growth in 2024AA – Experiment and modeling
PublicationThis paper presents the results of experimental low-cycle fatigue (LCF) tests conducted on EN-AW 2024 alloy in T3511 temper at 100 ◦C, 200 ◦C and 300 ◦C. The material’s basic fatigue characteristics were determined, such as fatigue life curve and cyclic strain curve. Both the hysteresis loop and nature of fracture surfaces obtained in macro- and microscopic observations (scanning electron microscope, SEM) were accounted for. The...
-
The Effect of Marginal Zn2+ Excess Released from Titanium Coating on Differentiation of Human Osteoblastic Cells
PublicationComposite coatings based on chitosan and zinc nanoparticles (ZnNPs) were successfully produced on Ti13Zr13Nb substrates by cathodic electrophoretic deposition (EPD). The unfavorable phenomenon of water electrolysis-induced nonuniformity was reduced by applying a low voltage (20 V) and a short deposition time (1 min). Surface analysis (roughness and hydrophilicity) reveals the potential of these coatings for enhancing cell attachment...
-
The effect of preliminary creep-strain on material behavior under LCF tension/compression and pure torsion regimes
PublicationThis paper presents the results of experimental tests of monotonic tension and torsion, creep-rupture and preliminary creep at 200C and 300C, as well as low-cycle fatigue of 2024 T3511 aluminum alloy. The fatigue process was conducted at room temperature for uniaxial tension/compression and torsion. The as-received material and pre-deformed material were also investigated during creep at elevated temperature. Basic monotonic,...
-
The Effect of Steaming Beech, Birch and Maple Woods on Qualitative Indicators of the Surface
PublicationThis work presents the effect of steaming beech, birch and maple woods on the resulting quality of the milled wood surface. The steaming process of the studied woods results in a targeted change in the color of the wood, which changes from the original light white-gray color to fine reddishbrown to dark brown color shades that are more or less saturated depending on the temperature of the saturated water steam. The color changes...
-
The experimental and numerical investigation of fracture behaviour in PMMA notched specimens under biaxial loading conditions – Tension with torsion
PublicationThis paper presents the results of experimental fracture test of flat PMMA specimens under biaxial loading condition tension with torsion (proportional). The specimens were made in two thicknesses: 5 and 15 mm and were weakened with V-type edge notches with different root radii: 0.5; 2 and 10 mm. Thanks to the ARAMIS 3D 4 M non-contact vision system, measurement of the elongation and twist angle were recorded. During experimental...
-
The Impact of Drying Conditions on the Surface Color Changes of Pine Wood
PublicationThe article presents the impact of drying process and selected parameters on the color changes on the surface of pine wood (Pinus sylvestris L.). Three predetermined process conditions (modes), mild, normal, and intensive, were investigated. The experiments were conducted using a semi-industrial scale dryer designed at the Gdańsk University of Technology with a loading capacity of 0.55 m3. The drying process was applied to pine...
-
The Influence of Global Corrosion Degradation on Localized Damage Detection Using Guided Waves
PublicationThis paper presents the results of a numerical analysis of the influence of corrosion degradation of metal plates on the wave propagation phenomenon. There are several different corrosion types, but general and pitting corrosion are the most common. General corrosion is more or less uniformly distributed over the entire exposed surface of the metal while pitting corrosion takes the form of localized cracks. Because the general...
-
The Influence of Impact Velocity on Stresses and Failure of S355j2 Steel Under Slurry Erosion Conditions
Publication -
The Influence of Impact Velocity on Stresses and Failure of S355j2 Steel Under Slurry Erosion Conditions
PublicationThe purpose of this work was to determine the essence of the influence of the impact velocity (5, 7, and 9 m/s) on Hertzian stresses and the erosion mechanism of ferritic-pearlitic S355J2 steel. The investigations were carried out using a slurry pot tester. S355J2 steel showed a strong sensitivity to changes in impact velocity. A significant increase in erosion rate was observed at a velocity of 9 m/s. This increase was 5-fold...
-
The Smith-Watson-Topper parameter and fracture surface topography relationship for additively manufactured 18Ni300 steel subjected to uniaxial variable-amplitude loading
PublicationIn this paper, the association between Smith-Watson-Topper (SWT) parameter and fracture surface topography is studied in additively manufactured maraging steel exposed to variable-amplitude fatigue loading. The post-failure fracture surfaces were examined using a non-contact 3D surface topography measuring system and the entire fracture surface method. The focal point is on the correspondence between fatigue characteristics, articulate...
-
The study on the appearance of deformation defects in the yacht lamination process using an AI algorithm and expert knowledge
PublicationThis article describes the application of the A-priori algorithm for defining the rule-based relationships between individual defects caused during the lamination process, affecting the deformation defect of the yacht shell. The data from 542 yachts were collected and evaluated. For the proper development of the algorithm, a technological process of the yacht lamination supported by expert decisions was described. The laminating...
-
The Use of Cluster Analysis to Assess the Wear Resistance of Cermet Coatings Sprayed by High Velocity Oxy-Fuel on Magnesium Alloy Substrate
PublicationCermet coatings are one of the best surface protection of machine elements against wear. On the other hand, the most universal and economically justified method of applying such coatings is high velocity oxy-fuel (HVOF) spraying. This method makes it possible to produce coatings characterized by compact structure, low porosity and very good adhesion to the substrate. All these fundamental properties contribute to the high wear...
-
Therapeutic biomaterials – application in neurology and cardiology
PublicationBiomaterials are of interest in most medical fields. It's hard to imagine life without them. And due to the ever-increasing demand, scientists are developing new materials. Diseases of the nervous and cardiovascular systems are still a big problem, which are associated with a limited ability to regenerate brain or heart tissues. Therefore, this review discusses the advancement in biomaterial engineering for the treatment of neurological...
-
Timed rolling and rising tests in Duchenne muscular dystrophy ambulant boys: a feasibility study
PublicationBACKGROUND: Functional activities are extensively used in motor assessments of patients with Duchenne muscular dystrophy. The role of timed items has been reported as an early prognostic factor for disease progression. However, there are two functional activities that are not widely assessed in clinical practice among Duchenne muscular dystrophy patients: rolling and bed rising. This study aimed to investigate whether the 360-degree...
-
Towards an analysis framework for operational risk coupling mode: A case from MASS navigating in restricted waters
PublicationMaritime Autonomous Surface Ships (MASSs) constitute highly interconnected and tightly coupled multistate systems. Incorporating the coupling effects of both interactions and dependencies is centrally important to ensure navigation safety of MASSs. This paper proposes a framework for examining the coupling effects in the operational modes (OM) of MASSs. Failure Modes (FMs) of MASSs related to interactions with the environment and...
-
Towards hand grip force assessment by using EMG estimators
PublicationThe purpose of this study was to propose a method to assess individual regression (calibration) curves to establish a relationship between an isometric grip force and surface electromyography (EMG) estimator. In this study 18 healthy volunteers (12 male (23.0 ± 2.0 years) and 6 female (23.2 ± 0.7 years)) had been examined. Ten EMG estimators (mean absolute value, root mean square, entropy, energy, turns per second, mean of zero...
-
Treatment of Odontogenic Maxillary Sinusitis with the Use of Growth Factors in Advanced Platelet-Rich Fibrin for Immediate Closure of Oro-Antral Communication: A Case Report
PublicationChronic odontogenic maxillary sinusitis (COMS), a prolonged inflammation of the maxillary sinus lasting over 12 weeks, is often a result of periapical lesions, marginal periodontitis, and complications like oro-antral communication (OAC) and fistula (OAF). OAC, commonly emerging post-teeth extraction in the lateral maxilla, lacks documented treatments using advanced platelet-rich fibrin (A-PRF). This study evaluates A-PRF’s efficacy...
-
Uniwersalne uchwyty obróbkowe wykorzystujące siły magnetyczne
PublicationPrzedstawiono współczesne konstrukcje uniwersalnych uchwytów przedmiotowych wykorzystujące do zamocowania przedmiotów obrabianych siły magnetyczne. Analizowano uchwyty magnetyczne i elektromagnetyczne w technologia obróbki wiórowej i ściernej oraz w technikach spawalniczych.
-
Walther H. Nernst - noblista z Wąbrzeźna
PublicationPrzedstawiono życiorys i osiągnięcia naukowe prof. Walthera Hermanna Nernsta, urodzonego 25 czerwca 1864 r. w Wąbrzeźnie, laureata Nagrody Nobla z dziedziny chemii z roku 1921. W. Nernst jest autorem m.in. III zasady termodynamiki oraz konstruktorem tzw. lampy Nernsta. Była to jedna z pierwszych lamp elektrycznych, oświetlająca wieżę Eiffla i pawilon niemiecki na Światowej Wystawie w Paryżu w 1890 r. W roku 1914 zostaje honorowym...
-
Window frame integrable air recuperation minichannel/minigap heat exchanger
PublicationThis article describes an evaluation of mini heat exchangers operation as a decentralized mechanical ventilation system with recuperative heat recovery that can be integrated into the window frame. The relatively small yet efficient air recuperation system allows for retrofitting existing buildings by reducing the overall energy consumption and thus the CO2 emissions. The proposed design, unlike existing systems, is easy to scale...
-
Wpływ dawkowania pasty ściernej na intensywność docierania próbek płaskich
PublicationPrzedstawiono wyniki badań intensywności docierania próbek płaskich ze stopu aluminium, brązu aluminiowego i żeliwa sferoidalnego na docierarce jednotarczowej. Analizowano wpływ okresowego dawkowania elektrokorundowej pasty ściernej na wydajność obróbki w funkcji czasu, w zależności od położenia próbek w separatorach oraz liczby próbek docieranych jednocześnie i wywieranego nacisku jednostkowego.
-
Wpływ parametrów strugi paliwa wtryskiwanego do cylindra silnika okrętowego na początkową fazę rozpylania
PublicationPrzedmiotem rozprawy jest analiza procesu wtrysku oleju napędowego do cylindra silnika okrętowego z zapłonem samoczynnym i bezpośrednim wtryskiem paliwa. Analiza tego zagadnienia została przeprowadzona w aspekcie wpływu makro parametrów strugi na początkową fazę rozpylania oleju napędowego. Celem niniejszej pracy jest określenie wpływu współczynnika L/D (długość otworu/średnica) otworu wylotowego wtryskiwacza na zmianę charakterystyki...
-
WPŁYW SKŁADU ANODY NA WYDAJNOŚĆ I STABILNOŚĆ TLENKOWYCH OGNIW PALIWOWYCH NIO+YSZ/YSZ/LACOFEO3-Δ
PublicationBadano wpływ proporcji składników anody na mikrostrukturę, widma impedancyjne i charakterystyki prądowo napięciowe testowych ogniw paliwowych z elektrolitem stałym na bazie tlenku cyrkonu stabilizowanego tlenkiem itru (YSZ), anodą NiO+YSZ i katodą LaCoFeO3-δ. Pomiary przeprowadzono dla różnej zawartości pary wodnej, ciśnienia parcjalnego wodoru, a także po starzeniu pod obciążeniem 300 mA/cm2. Najlepszą wydajność i stabilność...
-
Wpływ wysokiej osteotomii piszczelowej na mechanikę stawu kolanowego
PublicationW rozprawie podjęto próbę weryfikacji wpływu zabiegu chirurgicznego wysokiej osteotomii piszczelowej na mechanikę stawu kolanowego. Po wykonanym przeglądzie literatury, postawiono trzy hipotezy, które poddano weryfikacji na drodze badań numerycznych. Otrzymane wyniki zwalidowano poprzez badania nacisków powierzchniowych występujących w stawach kolanowych świni domowej, prowadzonych na maszynie do jednoosiowego ściskania. Praca...
-
Wpływ zawartości grafitu na właściwości mechaniczne warstw hybrydowych Ni-P/Si3N4/grafit osadzonych na stopie AW-7075 metodą redukcji chemicznej.
PublicationPrzedstawiono wpływ obecności grafitu jako fazy dyspersyjnej na właściwości mechaniczne warstw hybrydowych Ni-P/Si3N4/grafit, które osadzono metodą redukcji chemicznej na stopie glinu AW-7075. Wykonano badania morfologii powierzchni warstw metodą mikroskopii świetlnej i skaningowej. Dalszą część pracy stanowiły badania mechaniczne, czyli pomiary mikrotwardości warstw oraz ich adhezji do aluminiowego podłoża, a także analizy wpływu...
-
Wytwarzanie i modyfikacja powierzchni porowatych struktur tytanowych przeznaczonych na implanty
PublicationCelem pracy było wytworzenie stopu Ti-13Nb-13Zr z wykorzystaniem technologii selektywnego topienia laserowego (SLM) oraz jego biofunkcjonalizacja za pomocą utleniania mikrołukowego (MAO), a następnie określenie wpływu parametrów procesowych na właściwości otrzymanych materiałów pod kątem ich zastosowania na implanty. Oceniono wpływ napięcia, natężenia i czasu procesu MAO przeprowadzanego w elektrolicie zawierającym wapń i fosfor...