Filtry
wszystkich: 2369
wybranych: 1977
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: moisture resistance factor
-
Corrosion and Cavitation Resistances of Low Alloy Steel After Frictional-Mechanical Treatment
PublikacjaPaper presents the results of the studies of wear, corrosion and cavitation resistances of the S355J2 low alloy medium carbon steel subjected to surface modification by friction-mechanical treatment, as tested in sea water simulated solution. To evaluate the effect of the surface treatment, the comparative studies of the corrosive properties of the steel before and after treatment have been considered. The treatment due to a severe...
-
Study of the NO2 sensing mechanism of PEDOT-RGO film using in situ Raman Spectroscopy
PublikacjaIn this work, the mechanism of the NO2 reaction with PEDOT-RGO composite film has been investigated via in situ Raman spectroscopy. Reduced graphene oxide (RGO), poly(3,4-ethylenedioxytiophene)-reduced graphene oxide (PEDOT-RGO) and poly(3,4-ethylenedioxytiophene)/ClO4− (PEDOT/ClO4−) films were fabricated using an electrodeposition method and used as resistance sensors of gaseous nitrogen dioxide. The experimental results indicate...
-
Evaluation of Low Temperature Properties of Rubberized Asphalt Mixtures
PublikacjaThe paper presents low-temperature test results of asphalt mixtures designed with use of bitumen modified by crumb rubber and also SBS polymer. Laboratory tests were conducted on two types of asphalt mixtures for wearing course – stone matrix asphalt (SMA 8) and porous asphalt (PA 8). This paper presents results of the following laboratory tests at low temperatures: TSRST test, three point bending creep test, fracture toughness...
-
Novel Cast Polyurethanes Obtained by Using Reactive Phosphorus-Containing Polyol: Synthesis, Thermal Analysis and Combustion Behaviors
PublikacjaPhosphorus-containing polyol applications in polyurethane synthesis can prevent volatilization of flame retardants and their migration on the surface of a material. In this work, novel cast polyurethanes were prepared by a one-step method with the use of different amounts of phosphorus-containing polyol, 4,4′–diphenylmethane diisocyanate and 1,4-butanediol. The chemical structure, thermal, physicochemical and mechanical properties...
-
Resistive gas sensors – Perspectives on selectivity and sensitivity improvement
PublikacjaResistive gas sensors are very popular and relatively inexpensive; they can operate at elevated or room temperature for years on end. The main disadvantage of resistive gas sensors is their limited selectivity and sensitivity, but various methods have been applied to improve their behavior. The composition of the porous gas sensing layer, or changes in the sensor’s operating temperature, can enhance the gas detection ability. Furthermore, emerging...
-
Modelling of the Baumann turbine stage operation Part II. Free and kinetic vibrations
PublikacjaIn this paper has been presented a methodology of validation a novel mathematical model dedicated to evaluation and prediction of material degradation and demage of steam turbine elements such as blades, valves and pipes due to three mechanisms: stress-corosion, high-temperature creep and low-cyclic fatigue. The validation concept is based on an experimental setup manufactured in the Laboratory of Faculty of Mechanical and Power...
-
Determining and verifying the safety integrity level of the safety instrumented systems with the uncertainty and security aspects
PublikacjaSafety and security aspects consist of two different group of functional requirements for the control and protection systems. In the paper it is proposed that the security analysis results can be used as a factor increasing or decreasing the risk level. It concerns a process of determining required safety integrity level of given safety functions. The authors propose a new approach for functional safety risk analysis. In this case...
-
Importance of Conjugation of the Bile Salt on the Mechanism of Lipolysis
PublikacjaWe aim to advance the discussion on the significance of the conjugation of bile salts (BS) in our organism. We hypothesize that conjugation influences the rate of lipolysis. Since the rate of lipolysis is a compound parameter, we compare the effect of conjugation on four surface parameters, which contribute to the rate. Since deconjugation is due to gut microbiota, we hypothesize that microbiota may affect the rate of lipolysis....
-
Endothelial Dysfunction Driven by Hypoxia—The Influence of Oxygen Deficiency on NO Bioavailability
PublikacjaCardiovascular diseases (CVDs) are the leading cause of death worldwide. The initial stage of CVDs is characterized by endothelial dysfunction, defined as the limited bioavailability of nitric oxide (NO). Thus, any factors that interfere with the synthesis or metabolism of NO in endothelial cells are involved in CVD pathogenesis. It is well established that hypoxia is both the triggering factor as well as the accompanying factor...
-
Ultrasound assisted dispersive solid phase microextraction using polystyrene-polyoleic acid graft copolymer for determination of Sb(III) in various bottled beverages by HGAAS
PublikacjaA new polyoleic acid-polystyrene (PoleS) block/graft copolymer was synthesized and applied as adsorbent for ultrasound assisted dispersive solid phase microextraction (UA-DSPME) of Sb(III) in different bottled beverages and analysis using hydride generation atomic absorption spectrometry (HGAAS). Adsorption capacity of the PoleS was 150 mg g−1. Several sample preparation parameters such as sorbent amount, solvent type, pH, sample...
-
Theory versus experiment for vacuum Rabi oscillations in lossy cavities
PublikacjaThe 1996 experiment by Brune et al. [Phys. Rev. Lett. 76, 1800 (1996)] on vacuum Rabi oscillation is analyzed by means of alternative models of atom-reservoir interaction. Agreement with experimental Rabi oscillation data can be obtained if one defines jump operators in the dressed-state basis and takes into account thermal fluctuations between dressed states belonging to the same manifold. Such low-frequency transitions could...
-
Sensitive simultaneous determination of 19 fluorobenzoic acids in saline waters by solid-phase extraction and liquid chromatography–tandem mass spectrometry
PublikacjaA solid-phase extraction (SPE) procedure using C18 stationary phase was optimized for the preconcentration of 19 fluorinated derivatives of benzoic acid (FBA): mono-, di-, tri-, and tetrafluorosubstituted in the ring, trifluoromethylbenzoic acid and 3,5-bistrifluoromethyl benzoic acid from undiluted salt-rich (>20%) reservoir waters. Quantitative (>90%) retention/elution of 16 out of 19 analyte compounds was achieved allowing a...
-
A new assay for simultaneous identification and differentiation of Klebsiella oxytoca strains
PublikacjaBacterial strain typing, or identifying bacteria at the strain level, is particularly important for diagnosis, treatment, and epidemiological surveillance of bacterial infections. This is especially the case for bacteria exhibiting high levels of antibiotic resistance or virulence, and those involved in nosocomial or pandemic infections. Strain typing also has applications in studying bacterial population dynamics.
-
Titanium Scaffolds – Hopes and Limitations
PublikacjaThe state-of-art on titanium scaffolds is briefly reviewed. The real hopes from medicine associated with scaffolds are indicated. The limitations of different scaffolds associated with their mechanical, chemical and biological properties are discussed. The great importance of titanium scaffolds is demonstrated as the materials of high biocompatibility and corrosion resistance, fair mechanical properties and important biological...
-
High temperature corrosion and corrosion protection of porous Ni22Cr alloys
PublikacjaIn this work corrosion kinetics of the porous IN625 alloy is studied in the temperature range of 700 °C – 800 °C in air and humidified hydrogen for up to 1000 hours. Moreover, an effective and simple method of reducing corrosion rates of porous alloys by the infiltration of the rare earths elements is shown. Modification by the yttrium containing precursor reduces the corrosion rate by a factor of 50 in air at 700 °C so that the...
-
Modeling of Passive and Forced Convection Heat Transfer in Channels with Rib Turbulators
PublikacjaThe main goal of the research presented in this paper was the experimental and numerical analysis of heat enhancement and aerodynamic phenomena during air flow in a channel equipped with flow turbulators in the form of properly configured ribs. The use of ribs intensifies the heat transfer and at the same time increases not only the flow resistance but also the energy costs. Therefore, designing modern heat exchangers with optimal...
-
PRZYCZEPY DO BADANIA OPORU TOCZENIA OPON DO SAMOCHODÓW OSOBOWYCH
PublikacjaPrzedstawiono doświadczenia Zespołu Pojazdów Katedry Konstrukcji Maszyn i Pojazdów Wydziału Mechanicznego Politechniki Gdańskiej dotyczące urządzeń badawczych (przyczep) do pomiaru oporu toczenia opon do samochodów osobowych i nawierzchni drogowych. Opisano przyczepy pomiarowe tego typu. Pomiary oporu toczenia opon samochodowych wymuszane są koniecznością osiągania przez pojazd jak największej swojej sprawności...
-
Effect of illumination on noise of silicon solar cells
PublikacjaTransport and noise properties of silicon solar cells in darkness and under illumination have been studied. The measurements were carried out for both reverse and forward bias of the device. The changes in the sample behaviour are due to the variation of PN junction dynamic resistance and, also, the occurence of both 1/f and generation-recombination noise components
-
Cutting model parameters from frame sawing of natural and impregnated Scots pine (Pinus sylvestris L.)
PublikacjaIn this paper, absolute and density normalized cutting model parameters of natural and impregnated Scots pine (Pinus sylvestris L.) are shown and a method for the calculation of their corresponding material properties in the principal material directions of wood is presented. The parameters were determined from measurements of cutting power on a sash gang saw, and are in detail the fracture toughness and the shear yield strength...
-
Pilot installation for thermal utilization of meat-and-bone meal using the rotary kiln pyrolyzer and the fluidised bed boiler
PublikacjaThe technology of thermal utilization of meat-and-bone meal (MBM) is still at the research state. However, there are already a number of existing pilot-scale installations that provide the complete, effective and environmentally safe process conducting. The universal technology was developed that allows to combust various types of waste, including animal waste, municipal waste and sludge, mixed at any ratio with different types...
-
3D Buckling Analysis of a Truss with Horizontal Braces
PublikacjaThe present research is devoted to the study of out–of–plane buckling of a truss with horizontal braces. The truss is a model of real roof truss scaled by factor 1=4. A linear buckling and a non–linear analysis with geometric and material non–linearity were carried out. The truss buckling and limit load for different stiffnesses and number of braces are found. Numerical analysis are verified by experiment. Threshold bracing stiffness condition...
-
Comparison of soil models in the thermodynamic analysis of a submarine pipeline buried in seabed sediments
PublikacjaThis paper deals with mathematical modelling of a seabed layer in the thermodynamic analysis of a submarine pipeline buried in seabed sediments. The existing seabed soil models: a “soil ring” and a semi-infinite soil layer are discussed in a comparative analysis of the shape factor of a surrounding soil layer. The meaning of differences in the heat transfer coefficient of a soil layer is illustrated based on a computational example...
-
Analiza porównawcza metod obliczania przebicia
PublikacjaW artykule przedstawiono analizę porównawczą wybranych normowych metod wyznaczania nośności na przebicie konstrukcji płytowo-słupowej. Przeanalizowano trzy normowe sposoby wyznaczania nośności na przebicie.Wykonane obliczenia pozwoliły na wskazanie różnic w wyznaczonych wartościach nośności płyty na przebicie w konstrukcji płytowo-słupowej.
-
Experimental investigation of Steel–Concrete–Polymer composite barrier for the ship internal tank construction
PublikacjaTransportation of dangerous cargo by ships demands ensuring an appropriate protection level in case of an accident. Two of the most dangerous accident types resulting in an oil spill are grounding and ship to ship collision. The article presents results of research on a new composite construction for a ship hull that increases structural safety during collision. The concept of semi-elastic Steel–Concrete–Polymer structure is presented....
-
Effect of TiO2 Concentration on Microstructure and Properties of Composite Cu–Sn–TiO2 Coatings Obtained by Electrodeposition
PublikacjaIn this work, Cu–Sn–TiO2 composite coatings were electrochemically obtained from a sulfate bath containing 0–10 g/L of TiO2 nanoparticles. The effect of TiO2 particles on kinetics of cathodic electrodeposition has been studied by linear sweep voltammetry and chronopotentiometry. As compared to the Cu–Sn alloy, the Cu–Sn–TiO2 composite coatings show rougher surfaces with TiO2 agglomerates embedded in the metal matrix. The highest...
-
Verification of punching shear outside the shear cap by the direct method
PublikacjaThe proposition of a method to verify the punching resistance for very large supports based on the EN 1992-1-1 standard is described in this paper. The present standard guidelines for the calculation of the punching resistance for large supports are also summarised. The proposed direct method is compared with other standard methods using an example taken from design practice. This method consists of a direct check of the shear...
-
Electric transport in organic system with planar DBP/F16ZnPc junction on the basis of direct current and small signal admittance spectra analysis
PublikacjaThe objective of this work was to determine electric transport in the organic device based on a planar junction of electron donor and electron acceptor materials, namely ITO/MoO3/DBP/F16ZnPc/BCP/Ag. The analysis reported herein was based on direct current-voltage measurements and small-signal admittance spectra in the dark and under illumination. Such analysis may provide information on potential barriers, parasitic resistances...
-
The effect of pre-hydrogen charging on corrosion behaviour of superduplex stainless steel welded joints
PublikacjaThe paper presents results of research undertaken to determine the influence of hydrogen on passivity and corrosion resistance of 2507 super duplex stainless steel welded joints. Butt welded joints were made with low heat input using flux corded arc welding (FCAW) method. Coupons of 5.0 x 5.0 mm were cut from the welded joints containing weld metal (WM), heat affected zone (HAZ) and parent metal (PM). Hydrogen was introduced...
-
Improvement of ships seakeeping performance by application of the Full-scale CFD simulations – case study
PublikacjaThe ship’s fuel economy is increasingly important. The paper presents the effect of redesigning a case study ship for increasing seakeeping performance. Selected wave parameters reflects very difficult operational con-ditions existing on the North Sea and the Baltic Sea. The analyzed variants of a case study ship represent the latest developments of modern hull forms. The concepts similar to V-shaped bulbous bow, X-bow, X-aft,...
-
Mn-Co spinel coatings on Crofer 22 APU by electrophoretic deposition: Up scaling, performance in SOFC stack at 850 °C and compositional modifications
PublikacjaCeramic coatings for metallic interconnects play a key role in limiting corrosion and chromium evaporation in solid oxide cells. This study presents the upscaling of the electrophoretic deposition (EPD) technique to process Mn-Co spinels on real-dimension Crofer 22 APU interconnects and the test in a SOFC stack. Area specific resistance of long-term test conducted for 5000 h at 850 °C demonstrated that two-steps sintering has a...
-
Effect of double thermal and electrochemical oxidation on titanium alloys for medical applications
PublikacjaThe research focuses on the development and characterization of innovative thin hybrid oxide coatings obtained in subsequent processes of thermal (TO) and electrochemical (EO) oxidation. Four different surface modifications were investigated and the microstructure was determined, the mechanical, chemical and biological properties of the Ti-13Nb-13Zr alloy were assessed using scanning electron microscopy, X-ray dispersion analysis,...
-
Effect of sintering temperature on electrochemical performance of porous SrTi1-xFexO3-δ (x = 0.35, 0.5, 0.7) oxygen electrodes for solid oxide cells
PublikacjaThis work evaluates the effects of the sintering temperature (800 °C, 900 °C, 1000 °C) of SrTi1-xFexO3-δ (x = 0.35, 0.5, 0.7) porous electrodes on their electrochemical performance as potential oxygen electrode materials of solid oxide cells. The materials were prepared by a solid-state reaction method and revealed the expected cubic perovskite structure. After milling, the powders were characterised by a sub-micrometre particle...
-
Nitric Oxide-Dependent Pathways as Critical Factors in the Consequences and Recovery after Brain Ischemic Hypoxia
PublikacjaBrain ischemia is one of the leading causes of disability and mortality worldwide. Nitric oxide (NO), a molecule that is involved in the regulation of proper blood flow, vasodilation, neuronal and glial activity constitutes the crucial factor that contributes to the development of pathological changes after stroke. One of the early consequences of a sudden interruption in the cerebral blood flow is the massive production of reactive...
-
Transformational leadership for researcher’s innovativeness in the context of tacit knowledge and change adaptability
PublikacjaThis study explores how a learning culture supported by transformational leadership influences tacit knowledge sharing and change adaptability in higher education and how these relations impact this sector’s internal and external innovativeness. The empirical model was tested on a sample of 368 Polish scientific staff using the structural equation modeling (SEM) method. Then results were expanded by applying OLS regression using...
-
Designing a high-sensitivity dual-band nano-biosensor based on petahertz MTMs to provide a perfect absorber for early-stage non-melanoma skin cancer diagnostic
PublikacjaThe purpose of this study is development of a novel high-performance low-Petahertz (PHz) biosensor for non-melanoma skin cancer (NMSC) diagnosis. The presented device is designed to work within a microwave imaging regime, which is a promising alternative to conventional diagnostic methods such as visual examination, dermoscopy, and biopsy. The suggested biosensor incorporates a dual-band perfect absorber (operating bands at 0.909...
-
Optimization of vortex-assisted hydrophobic magnetic deep eutectic solvent-based dispersive liquid phase microextraction for quantification of niclosamide in real samples
PublikacjaIn this manuscript, a green and fast vortex-assisted hydrophobic magnetic deep eutectic solvent-based dispersive liquid phase microextraction (VA-HMDES-DLPME) method was developed for the selective extraction and determination of niclosamide in read samples, including rice, medicine tablets, and water samples. Here, hydrophobic magnetic deep eutectic solvents were used as the extracting solvent without requiring any centrifugation...
-
Reactive imines: Addition of 2-aminopyrimidine to the imine bond and isolation of the aminal from the equilibrium mixture aminal/imine
PublikacjaThe reaction between o-vanillin and 2-aminopyrimidine leads to the formation of a single crystalline product: aminal, 1, which results from the reaction of the initially formed imine with 2-aminopyrimidine. The reaction was followed by the NMR spectroscopy. VT NMR studies prove that in solution two major species are observed: aminal and imine and their ratio depends on the time or/and temperature with the imine content increasing...
-
Pharmaceuticals and other contaminants of emerging concern in Admiralty Bay as a result of untreated wastewater discharge: Status and possible environmental consequences
PublikacjaConsidering how the impact of human activity in Antarctica is growing, the aim of this study was to conduct the first assessment of pharmaceuticals and personal care products (PPCPs), other emerging contaminants (ECs), and antibiotic resistance genes present in the western shore of the Admiralty Bay region of King George Island. In total, more than 170 substances were evaluated to assess the potential environmental risks they pose...
-
Experimental study on the seepage flow through the ice jam
PublikacjaIn light of the observed climate change, there is a need for better understanding of river ice processes for managing water resources in the cold regions. Ice jams produce significant resistance which may cause rise of water level and flooding. The jam resistance is only referred to the roughness of its underside, and this approach lead to exceptional roughness coefficients which has no physical explanation. Number of evidences...
-
Emerging anticancer activity of candidal glucoseamine-6-phosphate synthase inhibitors upon nanoparticle-mediated delivery
PublikacjaNumerous glutamine analogues have been reported as irreversible inhibitors of the glucosamine-6-phosphate (GlcN-6-P) synthase in pathogenic Candida albicans in the last 3.5 decades. Among the reported inhibitors, the most effective N3-(4-methoxyfumaroyl)-L-2,3- diaminopropanoic acid (FMDP) has been extensively studied in order to develop its more active analogues. Several peptide−FMDP conjugates were tested to deliver FMDP to its...
-
A newly-developed model for predicting cutting power during wood sawing with circular saw blades
PublikacjaIn the classical approach, cutting forces and cutting power in sawing processes of orthotropic materials such as wood are generally calculated on the basis of the specific cutting resistance kc (cutting force per unit area of cut). For every type of sawing kinematics (frame saws, band saws and circular sawing machines) different empirical values of specific cutting resistance kc have to be applied. It should be emphasised that...
-
Analysis of features of stainless steels in dissimilar welded joints in chloride inducted corrosion
PublikacjaStainless steels of femtic-austenitic microstructure that means the duplex Cr-Ni-Mo steels, in comparison with austenitic steel includes less expensive nickel and has much better mechanical properties with good formability and corrosion resistance, even in environments containing chloride ions. Similar share of high chromium ferrite and austenite, which is characterized by high ductility, determines that the duplex steels have...
-
Design and characterization of apatite La9.8Si5.7Mg0.3O26±δ-based micro-tubular solid oxide fuel cells
PublikacjaIn this study, electrolyte-supported (Cell A) and anode-supported (Cell B) micro-tubular solid oxide fuel cells (SOFCs) based on the La9.8Si5.7Mg0.3O26±δ (LSMO) electrolyte is built through an extrusion and dip-coating processes. The formulations and process conditions for these cells are established and optimized. Both cell configurations show no visible delamination or cracking, and reaction zones and inter-diffusion of any species...
-
Wpływ strat mechanicznych w siłowniku teleskopowym zespołu zagęszczającego w pojeździe do usuwania odpadów z pojemników na skuteczność prasowania odpadów
PublikacjaHydraulic telescopic cylinders are used to power the moving wall of rear loader garbage trucks equipped with the traditional "sweep and slide" system. As the garbage compression force is directly dependent on the resistance force of the moving wall, losses in the hydraulic telescopic cylinder influence the compaction process. Taking them into account in the control system may improve the operation of the compaction...
-
Prebiotics and probiotics in food
PublikacjaNowadays, food is not only used to satisfy hunger and is a source of nutrients, but is also considered a factor that directly affects human health. Consumers are looking for high-quality products that contain bioactive ingredients that affect the proper functioning of the body and good mood. Functional foods, which must exhibit health benefits when consumed as part of a balanced diet, are becoming increasingly popular among health-conscious...
-
The concept of anti-collision system of autonomous surface vehicle
PublikacjaThe use of unmanned vehicles in various fields of science and the economy is becoming more common. An extremely important aspect of creating this type of solution is to provide autonomous vehicle navigation, which does not require interference of the human factor or in which it is limited to a minimum. This article discusses the concept of autonomous anti-collision system of unmanned surface vehicle. It proposed a sensor system...
-
Charakterystyka areodynamiczna membranowego przekrycia wiszącego.
PublikacjaArtykuł przedstawia charakterystykę aerodynamiczną membranowego przekrycia wiszącego. Prezentowane są dwie koncepcje przyjmowania wartości współczynnika aerodynamicznego. Pierwsza z koncepcji bazuje bezpośrednio na testach laboratoryjnych druga zaś wykorzystuje uproszczone podejście normowe.This paper presents the aerodynamic characteristics of membrane hanging roof. The two concepts of taking the value of the aerodynamic factor...
-
Determinanty kreowania wartości marki poprzez media społecznościowe w gospodarce sieciowej
PublikacjaGłównym problemem badawczym podejmowanym w pracy, jest określenie struktury czynników determinujących kreowanie wartości marki w mediach społecznościowych. Dla rozwiązania tego problemu wykonano dwa badania. Pierwsze z nich dotyczyło określenia relacji pomiędzy wartością marki a jej pozycją w sieciach społecznościowych (model BV). Badanie to zrealizowano w oparciu o metody ilościowe: analizę statystyczną danych wtórnych i danych...
-
The influence of drying parameters on wood properties
PublikacjaThe influence of drying conditions on wood properties is presented. The classical approach was used to determine energetic effects (cutting forces and cutting power) of wood sawing process on the basis of the wood specific cutting resistance, material constant. Before mashining wood material (soft and hard) was dryied at various conditions using air at 25oC, air-steam meaxture at 80oC and steam at 110oC.
-
Wear of Ultra-thin DLC or Tungsten-modified DLC Coatings under Reciprocating Sliding
PublikacjaIn the paper results are presented from tests in reciprocating sliding of self mated specimens of DLC and tungsten modified DLC coatings on stainless steel substrate. The contact geometry chosen for the research task was ball on flat. The contacts were lubricated either with distilled water or medical saline solution. Results are presented with regard to wear resistance as a function of material type and lubricant used.