Wyszukiwarka
Filtry
wszystkich: 2638
wybranych: 2393
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: THERMAL ANALYSIS,NUMERICAL SIMULATIONS,AMPACITY,POWER CABLES
-
A new viscoelastic method of calculation of low-temperature thermal stresses in asphalt layers of pavements
PublikacjaThe paper presents a new method of calculation of thermal stresses in asphalt layers of pavements induced by cooling or heating. The method, developed by the author, is based on the analytical solution for the linear viscoelastic Burgers model extended numerically for the case of asphalt layers whose rheological parameters are strongly dependent on temperature. The coefficient of thermal expansion and Poisson’s ratio may optionally...
-
The effect of fishing basin construction on the behaviour of a footbrdge over the port channel
PublikacjaThe paper analyses possible causes of failure of the rotating footbridge over the Ustka port channel. In July, 2015, strange behaviour of this object was observed in the form of excessive vibrations of bridge platform suspension rods, with the accompanying acoustic effects. A preliminary geotechnical analysis has revealed that this destructive effect was caused by the nearby construction works, namely construction of a fishing...
-
Looking for a minimum exergy destruction in hierarchical cycle
PublikacjaThe paper presents results of energy analysis, complemented with an exergy balance, of hierarchical thermodynamic cycle. Proposed cycle is a binary vapour cycle based on a model of real supercritical steam power plant. Energy analysis is used to preliminary optimization of the cycle and the exergy losses analysis is proposed to perform optimization of heat transfer processes, which are essential for hierarchical cycles. Proposed...
-
Formation of intermetallic compounds in the solid-liquid composites of the Ga-Ni system
PublikacjaThe processes of formation of intermetallic compounds in the composite system of liquid gallium-nickel powder by the methods of x-ray diffraction, scanning electron microscopy and differential thermal analysis have been studied. A change in the phase composition was discovered and the influence of thermal treatment of the composites under investigation on the phase formation processes was analyzed. The mechanism of gallium enriched...
-
Expedited Optimization of Passive Microwave Devices Using Gradient Search and Principal Directions
PublikacjaOver the recent years, utilization of numerical optimization techniques has become ubiquitous in the design of high-frequency systems, including microwave passive components. The primary reason is that the circuits become increasingly complex to meet ever growing performance demands concerning their electrical performance, additional functionalities, as well as miniaturization. Nonetheless, as reliable evaluation of microwave device...
-
Comparison of experimental and numerical results on metallic plates subjected to explosions
PublikacjaA comparative study of dynamic response including damage and rupture processes of thin metallic plates subjected to shockwave impulses - explosions is presented. The results of the finite element numerical analysis are related to experiments. Due to high strain rate during explosions the elasto-viscoplastic Chaboches constitutive law including damage effects has been applied. For the assumed model proper material parameters identification...
-
Modelowanie kratownicy z kształtowników giętych na zimno z mimośrodami dodatnimi w węźle = Modelling of truss with cold-formed section and positive eccentricyty in the node.
PublikacjaThe topic of this research is establishing load-carrying capacity of compressed and tensed chords of trusses made of cold-formed open cross-sections. Occurrence of bending in the truss’ chord is the result of specific production technology assumed by the designer and producer of lattice girder’s systems. The aim of this research is to present methodology of conduct while creating numerical models that best depict the behaviour...
-
The interaction of the pulsed laser irradiation with titania nanotubes - Theoretical studies on the thermal effect
PublikacjaThis paper reports temperature dispersion simulations of titania nanotubes irradiated by the 355 nm, pulsed, nanosecond laser. The modelling with the use of Finite Elements Method concerns titania nanotubes of the length and the wall thickness in the range of 0.5–2 μm and 5–20 nm, respectively. The uniqueness of the morphology was preserved by ensuring the wall thickness variation along the height of the tube, which was determined...
-
EFFECT OF WORKING FLUID SELECTION ON THERMAL PERFORMANCE OF HEAT EXCHANGER FILLED BY THE POROUS MATERIAL
PublikacjaThermal management of electronics semiconductor technologies that are located i.e. in a novel marine power plants or computer server rooms become very important issue for designers of such systems. Motivation and need for research in development of novel cooling strategies for modern electronics is of paramount importance. Heat exchangers filled by the porous material are a novel research topic in current heat pipe science. The...
-
Towards high quality ITO coatings: the impact of nitrogen admixture in HiPIMS discharges
PublikacjaThe paper reports controlled deposition of optically transparent and electrically conductive ITO films prepared by a combination of rf (13.56 MHz) and High Power Impulse Magnetron Sputtering (HiPIMS) systems without any post deposition thermal treatment/annealing. It is shown that (i) reactive admixture of N2 gas to the process and (ii) pressure in the deposition chamber enable to optimize optical properties of ITO films. Furthermore,...
-
Large deformation finite element analysis of undrained pile installation
PublikacjaIn this paper, a numerical undrained analysis of pile jacking into the subsoil using Abaqus software suit has been presented. Two different approaches, including traditional Finite Element Method (FEM) and Arbitrary Lagrangian–Eulerian (ALE) formulation, were tested. In the first method, the soil was modelled as a two-phase medium and effective stress analysis was performed. In the second one (ALE), a single-phase medium was assumed...
-
Portico Farmhouses of the Vistula Delta: Architecture, Current State and Finite Element Modelling of Timber Roof Truss under Material and Cross-section Uncertainty
PublikacjaThe article focuses on the oldest surviving I-type portico houses located in the Vistula Delta, which were built in the 17th and 18th centuries. The study describes the houses’ origins, structure, details of roof structures and technical condition, and it also includes numerical modelling of a roof truss and its mechanical analysis. Numerical models of the roof trusses are defined and analysed by means of the finite element method....
-
Design Evolution of the Ultrasonic Piezoelectric Motor Using Three Rotating Mode Actuators
PublikacjaThe development process and experimental investigation of the multicell piezoelectric motor is presented in this paper. The proposed design consists of three individual cells integrated into the stator, double rotor, and a preload system. Those elements are combined into a symmetrical structure of the motor. The two new prototypes have been designed, simulated and tested. Finite element numerical analysis is carried out to obtain...
-
Human factors in nuclear power engineering in Polish conditions
PublikacjaThe paper “Human factors in nuclear power engineering in polish conditions” focuses on analysis of dynamics of preparing polish society to build first nuclear power plant in XXI century in Poland. Authors compare experience from constructing nuclear power plant Sizewell B (Great Britain) and Sizewell C, which is in preparation phase with polish nuclear power program. Paper includes aspects e.g. of creating nuclear safety culture...
-
Feasibility Study GaN Transistors Application in the Novel Split-Coils Inductive Power Transfer System with T-Type Inverter
PublikacjaA promising solution for inductive power transfer and wireless charging is presented on the basis of a single-phase three-level T-type Neutral Point Clamped GaN-based inverter with two coupled transmitting coils. The article focuses on the feasibility study of GaN transistor application in the wireless power transfer system based on the T-type inverter on the primary side. An analysis of power losses in the main components of the...
-
Human Factors in Nuclear Power Engineering in Polish Conditions
PublikacjaThe paper “Human factors in nuclear power engineering in polish conditions” focuses on analysis of dynamics of preparing polish society to build fi rst nuclear power plant in XXI century in Poland. Authors compare experience from constructing nuclear power plant Sizewell B (Great Britain) and Sizewell C, which is in preparation phase with polish nuclear power program. Paper includes aspects e.g. of creating nuclear safety culture and...
-
Thermal boundary conditions to simulate friction layers and coatings at sliding contacts
PublikacjaA brief review of the thermal boundary conditions specified at sliding interfaces was performed. New thermal boundary conditions were derived aimed at solving problems of sliding with account of surface layers representing friction layers and tribological coatings. Based on the assumption of linear temperature distributions in the surface layers, the proposed conditions enable one to simplify simulations by eliminating the surface...
-
Dynamic analysis of the railway bridge span under moving loads
PublikacjaThe first part of this paper provides a review of the state of knowledge of the dynamic behaviour of railway bridges under moving loads. Particular attention is paid to developments in modelling railway bridge loading and dynamic vehicle-span (structure) interaction. The most important aspects determining the advancements in this area of knowledge are identified. The contemporary techniques for defining bridge span finite element...
-
Infiltration in a double-porosity medium: Experiments and comparison with a theoretical model
PublikacjaThis paper presents experimental verification of the mathematical model of unsaturated flow in double‐porosity soils developed by the asymptotic homogenization method. A series of one‐dimensional infiltration experiments was carried out in a column filled with a double‐porosity medium composed of a mixture of sand and sintered clayey spheres arranged in a periodic manner. The unsaturated hydraulic properties of each porous material...
-
New synthesis route of highly porous InxCo4Sb12 with strongly reduced thermal conductivity
PublikacjaHighly porous, In-filled CoSb3 skutterudite materials with an attractive thermoelectric figure of merit (ZT * 1) and corresponding dense samples were fabricated through the cost-effective method of reduction in oxides in dry hydrogen and the pulsed electric current sintering (PECS) method, respectively. The reduction process was described in detail using in situ thermogravimetric analysis of Co2O3, Sb2O3 and In(NO3)35H2O separately...
-
Preliminary Investigation on Auto-Thermal Extrusion of Ground Tire Rubber
PublikacjaGround tire rubber (GTR) was processed using an auto-thermal extrusion as a prerequisite to green reclaiming of waste rubbers. The reclaimed GTR underwent a series of tests: thermogravimetric analysis combined with Fourier-transform infrared spectroscopy (TGA-FTIR), scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR), and static headspace and gas chromatography-mass spectrometry (SHS-GC-MS) in order...
-
Oddziaływania taboru na mosty kolejowe przy zmiennych parametrach ruchu
PublikacjaW pracy poruszono zagadnienia związane z identyfikacją oraz modelowaniem układu dynamicznego most-pojazd ruchomy. Za element szczególnie istotny uznano czynnik obciążający. Opracowano i wdrożono metodykę identyfikacji cech dynamicznych rzeczywistego pojazdu szynowego. Eksperyment badawczy przeprowadzono dla jednostki trakcyjnej EN57, jednak nie ma żadnych ograniczeń w stosowaniu metody dla innego, konwencjonalnego taboru szynowego....
-
A high-accuracy complex-phase method of simulating X-ray propagation through a multi-lens system
PublikacjaThe propagation of X-ray waves through an optical system consisting of many X-ray refractive lenses is considered. For solving the problem for an electromagnetic wave, a finite-difference method is applied. The error of simulation is analytically estimated and investigated. It was found that a very detailed difference grid is required for reliable and accurate calculations of the propagation of X-ray waves through a multi-lens...
-
Estimation of Conservative Contaminant Travel Time through Vadose Zone Based on Transient and Steady Flow Approaches
PublikacjaEstimation of contaminant travel time through the vadose zone is needed for assessing groundwater vulnerability to pollution, planning monitoring and remediation activities or predicting the effect of land use change or climate change on groundwater quality. The travel time can be obtained from numerical simulations of transient flow and transport in the unsaturated soil profile, which typically require a large amount of data and...
-
Full-scale CFD simulations for the determination of ship resistance as a rational, alternative method to towing tank experiments
PublikacjaResults of ship resistance predictions obtained from towing tank experiments are affected by the method used to extrapolate from a model scale to a ship scale. Selection of method to determine a form factor is subjective and the extrapolation method is accurate for typical hull forms. For innovative hull forms the proper method for calculating the form factor is questionable. Moreover, the influence of the extrapolation method...
-
Evaluati on of long-term start up costs impact on short-term price based operational optimization of a CCGT using MILP
PublikacjaAn increasing share of the weather-dependent RES generation in the power system leads to the growing importance of flexibility of conventional power plants. They were usually designed for base load operation and it is a challenge to determine the actual long-term cycling costs, which account for an increase in maintenance and overhaul expenditures, increased forced outage rates and shortened life expectancy of the plant and components....
-
LDFEM analysis of pore water pressure development in cohesive soil due to FDP auger drilling
PublikacjaThis paper presents the preliminary modelling of FDP auger drilling in soft soil with emphasis on excess pore water pressure (EPWP) development using CEL formulation and Abaqus software suit. The EPWP generation in single points is investigated and the results of a numerical analysis are compared with the field measurements. It is found that numerical model qualitatively reflects the field measurements. However,...
-
Investigations of Energy Conversion and Surface Effect for Laser-Illuminated Gold Nanorod Platforms
PublikacjaAchieving a quick temperature increase is a burning issue for biophysical applications, like germ inactivation and tumor ablation, and for energy performances, like solar collectors and steam generators. Based on the plasmon resonance phenomenon, noble metallic nanoparticles have emerged as promising weapons due to their very high biocompatibility, optical properties, and high surface-to-volume ratio, increasing energy conversion...
-
Status report on high temperature fuel cells in Poland – Recent advances and achievements
PublikacjaThe paper presents recent advances in Poland in the field of high temperature fuel cells. The achievements in the materials development, manufacturing of advanced cells, new fabrication techniques, modified electrodes and electrolytes and applications are presented. The work of the Polish teams active in the field of solid oxide fuel cells (SOFC) and molten carbonate fuel cell (MCFC) is presented and discussed. The review is oriented...
-
The Influence of a Photovoltaic Micro-Installation on the Low-Frequency Parameters of Electricity at PCC and Its Impact on the Thermal Characteristics of Selected Devices
PublikacjaThis manuscript illustrates the measurement results of parameters describing the quality of energy at the PCC (point of common coupling) of a photovoltaic micro-installation that can significantly affect devices in the same power grid. The analyses reflecting heating of selected devices used in domestic installations, which were performed in an isolated laboratory environment, are also indicated. The conducted study aimed at checking...
-
Comparative study of operation of condensing and traditional boilers equipped with the ORC module for electricity generation
PublikacjaCondensing technology applied to boilers is to make full use of thermal energy contained in the fuel. That means that additionaly the heat from condensation of exhaust gases can be used for the purposes of heating the domestic hot water and to cover the demand for central heating. The study analyzed the operation of the "traditional" boiler equipped with the ORC module as the similar arrangement but with the condensing boiler....
-
Modelling of dielectric properties of BiNbO4-based microwave ceramics
PublikacjaIn the present paper results of the studies devoted to computer simulations of dielectric response of electroceramics in a frequency domain as well as analysis of the experimental data are given. As an object of investigations BiNbO4-based microwave ceramics was taken. Simulations of the hypothetical impedance response of the ceramic system were performed under assumption of the brick-layer model. A strategy for analysis and modelling...
-
Earthquake-induced pounding between asymmetric steel buildings
PublikacjaEarthquake-induced pounding between buildings has been the subject of numerous numerical and experimental studies in the resent years. The phe-nomenon may cause severe damage to structural elements as well as may also lead to the total collapse of colliding structures. A major reason leading to pounding between adjacent, insufficiently separated buildings results from the differences in their dynamic properties. The aim of this...
-
TRAVELLING WAVES FOR LOW–GRADE GLIOMA GROWTH AND RESPONSE TO A CHEMOTHERAPY MODEL
PublikacjaLow-grade gliomas (LGGs) are primary brain tumours which evolve very slowly in time, but inevitably cause patient death. In this paper, we consider a PDE version of the previously proposed ODE model that describes the changes in the densities of functionally alive LGGs cells and cells that are irreversibly damaged by chemotherapy treatment. Besides the basic mathematical properties of the model, we study the possibility of the...
-
Flow Analysis of a Kaplan Turbine
PublikacjaThis monograph is a guide to a method of experimental and numerical flow investigations for Kaplan - type turbines. The numerical calculations were compared with the test results of the model Kaplan turbine. The tests were carried out on the model test rig in the Gdańsk University of Technology. The turbine has been thoroughly experimentally investigated, resulting in the identification of optimum setting combination of the stator...
-
Optimal Rotating Receiver Angles Estimation for Multicoil Dynamic Wireless Power Transfer
PublikacjaThis study proposed an approach to dynamic wireless charging that uses a rotating receiver coil. Our simulation study focused on the verification of a novel way of increasing the coupling coefficient and power transfer stability by following the flux of the transmitting coils. To obtain the highest possible coupling by means of the FEM analysis, we studied the optimization of the trajectory of the angular velocity of the rotating...
-
The Methodology of identifying the place to install shunt compensators in the transmission network
PublikacjaThis methodology of selection and localization of static com- paper presents pensators in wide network. Proposed method is based on analysis of voltage area power profiles in the nodes of the power grid, and designating locations, In Which Voltages ex- cessively tend to change in time. Practical way of modeling the SVC device in PLANS program you Presented, as well as some example results of research.
-
THE INFLUENCE OF PHASE SHIFTERS ON THE VOLTAGE STABILITY OF CONNECTED POWER SYSTEMS
PublikacjaThe paper presents the results of simulation tests of connected power systems in which phase shifters were installed on cross-border links. The analysis was carried out in terms of assessing the impact of shifters on node voltage stability. Individual systems were characterized by different balance of active power: deficit or excess. The evaluation of voltage stability was based on the dU/dQ and dU/dP criteria.
-
Stirling engines - the state of technology development and computational models
PublikacjaStirling engines represent a technologically important solution in combined heat and power systems. Their use enables the achievement of over 90 percent efficiency in the management of the primary energy source with a very high durability of the device, mainly due to the lack of contact of the working gas with external factors and a very small number of mechanical components. The use of a Stirling engine may be equally important...
-
Building damage due to structural pounding during earthquakes
PublikacjaEarthquake-induced pounding between adjacent buildings has been identified as one of the reasons for substantial damage or even total collapse of colliding structures. A major reason leading to interactions in buildings results from the differences in their dynamic parameters and also from insufficient distance between the structures. Although the research on structural pounding has been much advanced, the studies have mainly been...
-
Study on the Structure-Property Dependences of Rigid PUR-PIR Foams Obtained from Marine Biomass-Based Biopolyol
PublikacjaThe paper describes the preparation and characterization of rigid polyurethane-polyisocyanurate (PUR-PIR) foams obtained with biopolyol synthesized in the process of liquefaction of biomass from the Baltic Sea. The obtained foams differed in the content of biopolyol in polyol mixture (0–30 wt%) and the isocyanate index (IISO = 200, 250, and 300). The prepared foams were characterized in terms of processing parameters (processing...
-
Prospects in elongation of railway transition curves
PublikacjaThe paper presents an analysis of the elongation of transition curves in relation to railway track alignment correction and modernisation. The analysis is based on numerical computations for a wide range of parameters describing a typical railway geometrical layout with transition curves. The differences between the horizontal ordinates of the existing layout and the layout with the elongated transition curves are evaluated and...
-
Analytical ‘Steady-State’-Based Derivation and Clarification of the Courant-Friedrichs-Lewy Condition for Pipe Flow
PublikacjaThis article addresses the problem of choosing the optimal discretization grid for emulating fluid flow through a pipeline. The aggregated basic flow model is linearized near the operating point obtained from the steady state analytic solution of the differential equations under consideration. Based on this model, the relationship between the Courant number (μ) and the stability margin is examined. The numerically set coefficient...
-
AN EXPERIMENTAL AND NUMERICAL STUDY ON THE PERFORMANCE OF AN INNOVATIVE VERTICAL-AXIS WIND TURBINE
PublikacjaThis paper introduces the innovative modification of the Savonius wind turbine being able to significantly increase efficiency in comparison with the classic design. This innovative design is equipped with a stator directing the flow. The presence of the stator increases the active surface area and generates higher torques acting on a shaft. Additionally, it makes it possible to take better advantage of wind energy and compensate...
-
Block Conjugate Gradient Method with Multilevel Preconditioning and GPU Acceleration for FEM Problems in Electromagnetics
PublikacjaIn this paper a GPU-accelerated block conjugate gradient solver with multilevel preconditioning is presented for solving large system of sparse equations with multiple right hand-sides (RHSs) which arise in the finite-element analysis of electromagnetic problems. We demonstrate that blocking reduces the time to solution significantly and allows for better utilization of the computing power of GPUs, especially when the system matrix...
-
The Application of a Multi-Criteria Decision-Making for Indication of Directions of the Development of Renewable Energy Sources in the Context of Energy Policy
PublikacjaThis paper presents the application of multi-criteria decision-making (MCDM) for evaluating what technologies using renewable energy sources (RES) for electricity production have the chance to develop in Poland under the current socio-economic conditions. First, the Analytical Hierarchy Process (AHP) method was used to determine the weights of the optimization criteria. Five main criteria and 30 sub-criteria were identified. Next,...
-
Thermo-elastic non-linear analysis of multilayered plates and shells
PublikacjaGeometrically nonlinear FEM analysis of multilayered composite plates and shells is performed in order to resolve the stability problem of the structures being under the influence of temperature field. The Riks-Wempner-Ramm algorithm with a specially modified multi-choice unloading condition has been implemented in authors’ numerical code. As the representation of multilayered medium the Equivalent Single Layer approach with the...
-
Przygotowanie, realizacja i ocena pomiarów terenowych do identyfikacji oporności hydraulicznej sieci wodociągowej
PublikacjaW procesie tworzenia komputerowego modelu przepływów (KMP) jednym z wiodących zadań jest przygotowanie i realizacja pomiarów terenowych w celu identyfikacji oporności hydraulicznej czynnej sieci wodociągowej. Motywacją autora do przedstawienia zasad postępowania w tym zakresie jest narastająca niefrasobliwość twórców KMP, którzy w nieuprawniony sposób używają paramodeli do rozwiązywania problemów inżynierskich. W pracy zdefiniowano...
-
The Finite Elements Method application to assesment the impact of turbulence generated by wind turbines on their lacation inclose proximity of overhead high voltage power transmissionlines
PublikacjaThe paper presents selected aspects of construction of wind turbines location concerning aerodynamic impact on power lines. Reaserch is based on the source data concerning the aerodynamic impact of a wind farm consisting of 8 turbines and 400 kV power line, an analysis of the possibility of wind farm locating in the immediate vicinity of the line was carried out. There are serious problems with locating higher capacity wind farms...
-
Optimization of Nuclear Power Share in the Structure of Electricity Production in Poland in Time Perspective by 2060
PublikacjaThe author of this paper presented the results of a system analysis using MARKAL model, aiming at the optimization of nuclear power share in power generation structure in Poland in time perspective by 2060. Optimization criterion is the minimization of the objective function, i.e. the total cost of energy system, taking into account constraints related to CO2, SOx and NOx emissions and obligatory shares of electricity from renewable...