Filtry
wszystkich: 1375
wybranych: 1187
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: RESIDUAL MAGNETIC FLUX
-
Low-strain sensor based on the flexible boron-doped diamond-polymer structures
PublikacjaA free-standing high boron-doped diamond nanosheet (BDDNS) has been fabricated for the development of a flexible BDDNS strain senor. High boron-doped diamond was initially grown on a tantalum substrate in a microwave plasma-assisted chemical vapor deposition method, and was then transferred to a Kapton polymer substrate to fabricate the flexible BDDNS/Kapton device. Before performing the transfer process, the thin BDDNS’s morphology...
-
Mechanical Performance and Environmental Assessment of Sustainable Concrete Reinforced with Recycled End-of-Life Tyre Fibres
PublikacjaThe presented research’s main objective was to develop the solution to the global problem of using steel waste obtained during rubber recovery during the tire recycling. A detailed comparative analysis of mechanical and physical features of the concrete composite with the addition of recycled steel fibres (RSF) in relation to the steel fibre concrete commonly used for industrial floors was conducted. A study was carried out using...
-
The Use of Direct Shear Test for Optimization of Interlayer Bonding Under a Poroelastic Layer
PublikacjaPoroelastic Road Surfaces (PERS) are characterised by porous structure with air void content of 20% or higher and stiffness almost 10 times lower than that of a standard asphalt course. Such properties enable noise reduction by up to 12 dB in comparison to SMA 11 mixture. However, the disadvantage of a poroelastic pavement is its low durability, which partially results from delamination from the lower layer. The paper aims to investigate...
-
KTaO3 a perovskite for water and air treatment
PublikacjaPerovskites are inorganic compounds that exhibit dielectric properties. These minerals belong to the crystal ceramics family. These compounds are described by the formula: ABX3 where, A and B are 2, 3 or 4 valuable metal ions, and X is an ion of oxygen or fluorine. An example of perovskite is the compound KTaO3. There are many methods for producing KTaO3, but the hydrothermal method is most commonly used. Perovskites can be characterized...
-
Noncentrosymmetric superconductor with a bulk three-dimensional Dirac cone gapped by strong spin-orbit coupling
PublikacjaThe layered, noncentrosymmetric heavy element PbTaSe2 is found to be superconducting. We report its electronic properties accompanied by electronic-structure calculations. Specific heat, electrical resistivity, and magnetic-susceptibility measurements indicate that PbTaSe2 is a moderately coupled, type-IIBCSsuperconductor (Tc = 3.72 K, Ginzburg–Landau parameter κ = 17) with an electron-phonon coupling constant of λep = 0.74. Electronic-structure...
-
Modular power converter topologies for energy storage and electric power distribution systems
PublikacjaThis paper describes selected issues concerning realization of energy storage system (ESS) designed to operate in power distribution system. In order to achieve scalability of the system a modular approach is proposed. In addition to this different configuration of the system are analyzed, where depending on requirements and application a scalability in power, in energy capacity of energy storage resource and both in power and...
-
Synthesis and properties of HoT2Al20 (T = Ti, V, Cr) intermetallic cage compounds
PublikacjaPolycrystalline samples of HoT2Al20 (T = Ti, V, Cr) intermetallics were synthesized using a step-wise arc-melting technique. All three compounds adopt the CeCr2Al20-type crystal structure with Ho atoms positioned inside oversized icosahedral cages formed by Al atoms. The structure of HoV2Al20 compound is reported. The materials properties were studied by means of electrical resistivity, magnetic susceptibility, and specific heat...
-
Two-step Conversion of Crude Glycerol Generated by Biodiesel Production into Biopolyols: Synthesis, Structural and Physical Chemical Characterization
PublikacjaIn this work biopolyols were synthesized via two-step process from crude glycerol and castor oil. For better evaluation of analyzed process, the impact of its time and temperature on the structure and properties of biopolyols was determined. Obtained results fully justified conducting of synthesis in two steps. Prepared materials were characterized by hydroxyl value and water content comparable to polyols industrially applied in...
-
Modern trends in solid phase extraction: New sorbent media
PublikacjaBased on the recently published literature, this review provides an update of the most important features and application of formats and devices employed in solid phase extraction (SPE). Special attention was paid on new trapping media proposed in SPE prior the chromatography analysis, based on the use of nanostructured materials, including carbon nanomaterials, electrospun nanofibers, dendrimes and magnetic nanoparticles, molecular...
-
Parametric versus nonparametric modelling of dynamic susceptibility contrast enhanced MRI based data
PublikacjaDynamic tracking of a bolus of a paramagnetic agent (dynamic susceptibility contract - DSC) in MRI (magnetic resonance imaging) measurements is successfully used for assessment of the tissue perfusion and the other features and functions of the brain (i.e. cerebral blood flow - CBF, cerebral blood volume - CBV, mean transit time - MTT). The parametric and nonparametric approaches to the identification of MRI models are presented...
-
Modelling of the High Speed Multi-Pole Synchronous Generator for Application in More Electric Aircraft Power Systems
PublikacjaIn this paper different models of the synchronous generator are presented. The simulation results compared with the measurements are shown. Certain physical phenomena are included in described models for the porpoise of adequate analysis of the more electric aircraft power system. For different modelling levels, such as functional level or behavioural level, different physical phenomena have been included. Simulation results for...
-
Identification and non-integer order modelling of synchronous machines operating as generator
PublikacjaThis paper presents an original mathematical model of a synchronous generator using derivatives of fractional order. In contrast to classical models composed of a large number of R-L ladders, it comprises half-order impedances, which enable the accurate description of the electromagnetic induction phenomena in a wide frequency range, while minimizing the order and number of model parameters. The proposed model takes into account...
-
Integration of Fluorescent, NV-Rich Nanodiamond Particles with AFM Cantilevers by Focused Ion Beam for Hybrid Optical and Micromechanical Devices
PublikacjaIn this paper, a novel fabrication technology of atomic force microscopy (AFM) probes integrating cantilever tips with an NV-rich diamond particle is presented. Nanomanipulation techniques combined with the focused electron beam-induced deposition (FEBID) procedure were applied to position the NV-rich diamond particle on an AFM cantilever tip. Ultrasonic treatment of nanodiamond suspension was applied to reduce the size of diamond...
-
Feasibility Study GaN Transistors Application in the Novel Split-Coils Inductive Power Transfer System with T-Type Inverter
PublikacjaA promising solution for inductive power transfer and wireless charging is presented on the basis of a single-phase three-level T-type Neutral Point Clamped GaN-based inverter with two coupled transmitting coils. The article focuses on the feasibility study of GaN transistor application in the wireless power transfer system based on the T-type inverter on the primary side. An analysis of power losses in the main components of the...
-
Modified Preisach model of hysteresis in multi air gap ferrite core medium frequency transformer
PublikacjaThis article presents the modified Preisach model of hysteresis for a 3-phase medium frequency transformer in a 100 kW dual active bridge converter. The transformer magnetic core is assembled out of ferrite I-cores, which results in multiple parasitic air gaps. For this transformer, the hysteresis loops were measured and parameters of the Preisach model were determined. The Preisach distribution function is approximated with a...
-
Pseudo-superparamagnetic behaviour of bariumhexaferrite particles
PublikacjaThe effect of hexadecyltrimethylammonium bromide (CTAB) addition on the crystal structure, morphology,and magnetic properties of co-precipitated hexagonal barium ferrite was investigated. For afixed amount ofsurfactant, different Fe3+concentrations and Fe3+/Ba2+ratios were used to optimize the formation ofsingle-phase barium ferrite particles. The results indicated that the obtained ferrite particles exhibitedcoercivity changes...
-
Recent Developments in Data-Assisted Modeling of Flexible Proteins
PublikacjaMany proteins can fold into well-defined conformations. However, intrinsically-disordered proteins (IDPs) do not possess a defined structure. Moreover, folded multi-domain proteins often digress into alternative conformations. Collectively, the conformational dynamics enables these proteins to fulfill specific functions. Thus, most experimental observables are averaged over the conformations that constitute an ensemble. In this...
-
Superconductivity in the superhard boride WB4.2
PublikacjaWe show that the superhard boride WB4.2 is a superconductor with a Tc of 2.05(5) K. Temperature-dependent magnetic susceptibility, electrical resistivity, and specific heat measurements were used to characterize the superconducting transition. The Sommerfeld constant γ for WB4.2 is 2.07(3) mJ mol−1 K−2 and the ΔC/γTc=1.56, which is somewhat higher than what is expected for weakly coupled Bardeen–Cooper–Schrieffer type superconductors....
-
Continuum wave functions for estimating the electric dipole moment: Calculation based on a multiconfiguration Dirac-Hartree-Fock approximation
PublikacjaThe multiconfiguration Dirac-Hartree-Fock method is employed to calculate the continuum electron wave functions, which are then used to estimate their contribution to the atomic electric dipole moment (EDM) of 129Xe. The EDM arises from (P,T)-odd electron-nucleon tensor-pseudotensor and pseudoscalar-scalar interactions, the nuclear Schiff moment, the interaction of the electron electric dipole moment with nuclear magnetic moments,...
-
Deposition and Electrical and Structural Properties of La0.6Sr0.4CoO3 Thin Films for Application in High-Temperature Electrochemical Cells
PublikacjaLow-temperature deposition of electroceramic thin films allows the construction of new devices and their integration with existing large-scale fabrication methods. Developing a suitable low-cost deposition method is important to further advance the development of microdevices. In this work, we deposited a 1-lm-thick La0.6Sr0.4CoO3d (LSC) perovskite with high electrical conductivity on sapphire substrates at 400C and analyzed its...
-
Satellite Image Classification Using a Hierarchical Ensemble Learning and Correlation Coefficient-Based Gravitational Search Algorithm
PublikacjaSatellite image classification is widely used in various real-time applications, such as the military, geospatial surveys, surveillance and environmental monitoring. Therefore, the effective classification of satellite images is required to improve classification accuracy. In this paper, the combination of Hierarchical Framework and Ensemble Learning (HFEL) and optimal feature selection is proposed for the precise identification...
-
The effect of shear deformations' rotary inertia on the vibrating response of multi-physic composite beam-like actuators
PublikacjaIn consecutive studies on flexomagneticity (FM), this work investigates the flexomagnetic reaction of a vibrating squared multi-physic beam in finite dimensions. It is assumed that the bending and shear deformations cause rotary inertia. In the standard type of the Timoshenko beam the rotary inertia originated from shear deformations has been typically omitted. It means the rotary inertia resulting from shear deformation is a new...
-
Trends in Locally Balanced Energy Systems without the Use of Fossil Fuels: A Review
PublikacjaIn recent years, the idea of the operation of energy systems (power systems, heating systems) has changed significantly. This paper is an overview of locally balanced energy systems without the use of fossil fuels. The paper justifies the concept of local energy balancing in a new energy system that does not use fossil fuels (coal, natural gas, and crude oil), based on European Union guidelines and formal documents as well as the...
-
Heat transfer intensification by enlarged surface roughness in the plate heat exchanger
PublikacjaIn the paper an experimental analysis of passive heat transfer intensification technique employed in the case of the plate heat exchanger is presented. The passive intensification was obtained by a modification of the heat transfer surface. The roughness of surface was increased by a use of glass micro-beads. Single-phase convective heat transfer in the water-water system was studied. The experiment was accomplished in two stages....
-
Enhanced electrochemical kinetics of highly-oriented (111)-textured boron-doped diamond electrodes induced by deuterium plasma chemistry
PublikacjaNovel highly-oriented (111)-textured boron-doped diamond electrodes (BDDD) featuring high electrochemical activity and electrode stability toward electrochemical analytics were fabricated by deuterium-rich microwave plasma CVD. The high flux deuterium plasma-induced preferential formation of (111)-faceted diamond as revealed by XRD. The highly-oriented diamond surface exhibited improved boron dopant incorporation and activation,...
-
Thermohydraulic maldistribution reduction in mini heat exchangers
PublikacjaA detailed numerical investigation has been carried out to analyze the flow maldistribution in 50 parallel 1 mm × 1 mm rectangular minichannels and 1 mm depth minigap section with rectangular, trapezoidal, triangular or concave manifolds in Z-type flow configuration. The working medium was ethanol and the mass flow rate was 5 × 10−4 kg/s. Both sections were heated from the bottom side. Heat flux of 10 000 W/m2 and 5000 W/m2 was...
-
Heat exchange enhancement of jet impingement cooling with the novel humped-cone heat sink
PublikacjaJet impingement cooling technology is applicable to control temperature of devices, where very high heat flux is generated within a small area. This paper is about the improvement of the jet impingement cooling efficiency by the heat sink geometry modification. Two reference cases were sourced from the literature – flat heat sink and modified one with cone in the jet stagnation region. Such a change improves cooling capability...
-
Effects of Noncontact Shoulder Tool Velocities on Friction Stir Joining of Polyamide 6 (PA6)
PublikacjaIn this study, the effects of the traverse and rotational velocities of the noncontact shoulder tool on the heat generation and heated flux during the friction stir joining of high-density polyamide 6 (PA6) polymer were investigated. The computational fluid dynamics (CFD) method was employed to simulate the thermomechanical phenomena during the friction stir joining (FSJ) process of PA6. A developed model was used to consider the...
-
Nonlinear model of a synchronous generator for analysis of more electric aircraft power systems
PublikacjaA nonlinear model for studying a variable-speed synchronous generator (SG) in more electric aircraft (MEA) power system has been developed. The saturation effects of the SG magnetic circuit have been considered. The model has been implemented in the Synopys/Saber simulation environment. The modelling language MAST has been used to elaborate the SG model. The model exhibit a network with the same number of external terminals/ports...
-
Application of the Mathar method to identify internal stress variation in steel as a welding process result
PublikacjaThe paper deals with the method to identify internal stresses in two-dimensional steel members. Steel members were investigated in the delivery stage and after assembly, by means of electric-arc welding. In order to perform the member assessment two methods to identify the stress variation were applied. The first is a non-destructive measurement method employing local external magnetic field and to detecting the induced voltage,...
-
A large family of filled skutterudites stabilized by electron count
PublikacjaThe Zintl concept is important in solid-state chemistry to explain how some compounds that combine electropositive and main group elements can be stable at formulas that at their simplest level do not make any sense. The electronegative elements in such compounds form a polyatomic electron-accepting molecule inside the solid, a ‘polyanion’, that fills its available energy states with electrons from the electropositive elements...
-
Charge density wave and large nonsaturating magnetoresistance in YNiC2 and LuNiC2
PublikacjaWe report a study of physical properties of two quasi-low-dimensional metals YNiC2 and LuNiC2 including the investigation of transport, magnetotransport, galvanomagnetic, and specific heat properties. In YNiC2 we reveal two subsequent transitions associated with the formation of weakly coupled charge density wave at TCDW=318K and its locking in with the lattice at T1=275K. These characteristic temperatures follow the previously...
-
Strong-coupling superconductivity of SrIr2 and SrRh2 : Phonon engineering of metallic Ir and Rh
PublikacjaExperimental and theoretical studies on superconductivity in SrIr2 and SrRh2 Laves phases are presented. The measured resistivity, heat capacity, and magnetic susceptibility confirm the superconductivity of these compounds with Tc = 6.07 and 5.41 K, respectively. Electronic structure calculations show that the Fermi surface is mostly contributed by 5d (4d) electrons of Ir (Rh), with Sr atoms playing the role of electron donors....
-
Effect of Axial Porosities on Flexomagnetic Response of In-Plane Compressed Piezomagnetic Nanobeams
PublikacjaWe investigated the stability of an axially loaded Euler–Bernoulli porous nanobeam considering the flexomagnetic material properties. The flexomagneticity relates to the magnetization with strain gradients. Here we assume both piezomagnetic and flexomagnetic phenomena are coupled simultaneously with elastic relations in an inverse magnetization. Similar to flexoelectricity, the flexomagneticity is a size-dependent property. Therefore,...
-
Opracowanie technologii spawania naprawczego szyn poddźwigowych A120 oraz badania nieniszczące jakości szyn w DCT w Porcie Północnym
PublikacjaEkspertyza dotyczy realizacji zlecenia związanego z naprawą spoin szyn poddźwigowych na terenie terminalu kontenerowego - Deep Water Terminal (DCT) w Porcie Północnym w Gdańsku. W ramach opracowania: 1. Wykonano badania ultradźwiękowe (UT) i magnetyczno-proszkowe (MT) spoin czołowych szyn poddźwigowych typu A120, według schematu dostarczonego przez firmę SKANSKA S.A. 2. Wykonano analizę wyników badań...
-
Thermal efficiency investigations on the self-ignition test engine fed with marine low sulfur diesel fuels
PublikacjaWithin the article an issues of implementing the new kinds of marine diesel fuels into ships’ operation was described taking into ac-count restrictions on the permissible sulphur content introduced by the International Maritime Organization. This is a new situation for ship owners and fuel producers, which forces the necessity to carry out laboratory research tests on especially adapted engine stands. How to elaborate the method...
-
Pedestrian detection in low-resolution thermal images
PublikacjaOver one million people die in car accidents worldwide each year. A solution that will be able to reduce situations in which pedestrian safety is at risk has been sought for a long time. One of the techniques for detecting pedestrians on the road is the use of artificial intelligence in connection with thermal imaging. The purpose of this work was to design a system to assist the safety of people and car intelligence with the use...
-
Fouling mechanisms in anoxic-aerobic sequencing batch membrane bioreactor based on adapted Hermia models and main foulant characteristics
PublikacjaVarious derivatives of Hermia models (complete pore blocking, intermediate pore blocking, cake layer formation, and standard pore blocking) and different assessments of foulant characteristics have long been used to determine the membrane fouling mechanisms. Accordingly, this study aims to adapt Hermia models and their combination according to the operating conditions of an anoxic-aerobic sequencing batch membrane bioreactor (A/O-SBMBR)....
-
Seismic performance evaluation of steel buckling-restrained braced frames including SMA materials
PublikacjaThe permanent deformation of the building after seismic excitations can be determined by the Maximum Residual Interstory Drift Ratio (MR-IDR), which may be used for measuring the damage states. Low-post yield stiffness of the steel buckling-restrained braced frame (BRBF) makes this system vulnerable to large MR-IDR after a severe earthquake event. To overcome this issue, this paper investigates the seismic limit state performances...
-
Innovative Implantable Left Ventricular Assist Device—Performance under Various Resistances and Operating Frequency Conditions
PublikacjaThis paper presents the operation of an innovative left ventricular assist device under various resistances and operating frequencies. The operating principle of the device is based on pulsatile blood flow, which is forced by a suction–discharge device pumping helium into a set of intra-cardiac balloons. In this way, the ejection fraction of the left ventricle is increased, and the mitral valve is additionally occluded. What is...
-
Comparative 3D DEM simulations of sand–structure interfaces with similarly shaped clumps versus spheres with contact moments.
PublikacjaThree-dimensional simulations of a monotonic quasi-static interface behaviour between initially dense cohesionless sand and a rigid wall of different roughness during tests in a parallelly guided direct shear test under constant normal stress are presented. Numerical modelling was carried out by the discrete element method (DEM) using clumps in the form of convex non-symmetric irregularly shaped grains. The clumps had an aspect...
-
Comparative analysis of thermodynamic cycles of selected nuclear ship power plants with high-temperature helium-cooled nuclear reactor
PublikacjaThis paper presents a comparative analysis of thermodynamic cycles of two ship power plant systems with a high-temperature helium- cooled nuclear reactor. The first of them is a gas system with recuperator , in which classical gas chamber is substituted for a HTGR reactor (High Temperature Gas-cooled Reactor) . The second of the considered cycles is a combined gas-steam system where working medium flux from gas turbine outlet...
-
Management of low-temperature heat source by ORC aided by additional heat source
PublikacjaThe presented work is aimed at utilisation of waste heat in the manner to produce electricity in ORC installation. Therefore the precondition of the study was to use the waste heat available in the form of a stream of hot water at 90°C. Such low enthalpy heat source is rather insufficient to produce a good quality vapour to feed the ORC turbine. That was the incentive to search for the ways of increasing the temperature of the...
-
Ce site dilution effects in the antiferromagnetic heavy fermion CeIn3
PublikacjaLa-doped intermetallic single crystals of Ce1−xLaxIn3 were synthesized via an In self-flux method throughout the entire range (x = 0–1). The prototypical heavy-fermion compound CeIn3 shows an antiferromagnetic phase transition at 10.1 K and becomes superconducting near a critical pressure where TN is completely suppressed. As the La concentration increases, Ce moments are diluted, and the lattice constant increases linearly, satisfying Vegard’s...
-
Core loss resistance impact on sensorless speed control of an induction motor using hybrid adaptive sliding mode observer
PublikacjaInduction motors (IMs) experience power losses when a portion of the input power is converted to heat instead of driving the load. The combined effect of copper losses, core losses, and mechanical losses results in IM power losses. Unfortunately, the core losses in the motor, which have a considerable impact on its energy efficiency, are not taken into account by the generally employed dynamic model in the majority of the studies. Due...
-
Comparison of Cadmium Cd2+ and Lead Pb2+ Binding by Fe2O3@SiO2‐EDTA Nanoparticles – Binding Stability and Kinetic Studies
PublikacjaThis study describes the synthesis and characterization of ethylenediaminetetraacetic acid (EDTA) functionalized magnetic nanoparticles of 20 nm in size – Fe3O4@SiO2‐EDTA – which were used as a novel magnetic adsorbent for Cd(II) and Pb(II) binding in aqueous medium. These nanoparticles were obtained in two‐stage synthesis: covering by tetraethyl orthosilicate and functionalization with EDTA derivatives. Nanoparticles were characterized...
-
Dynamics of fault arc traveling along busbars in high voltage switchboards = Dynamika łuku zwarciowego przemieszczającego się wzdłuż szyn rozdziel-nic wysokiego napięcia
PublikacjaThe paper presents the results of magnetic induction and electrodynamic force calculations acting on arc column during short-circuit in medium voltage air-insulated bus-bars. The gap between the bars was 120 mm and the prospective short-circuit currents ranged from 4 kA to 8 kA. The paper also shows the measurement results of average velocity fault arc depending on currents arc diameter and arc current was established and described....
-
Superconductivity in a new intermetallic structure type based on endohedral Ta@Ir7Ge4 clusters
PublikacjaWe report the observation of superconductivity at a temperature near 3.5 K for the previously unreported compound TaIr2Ge2. In addition to being a superconductor, this material displays a new crystal structure type that contains endohedral clusters, as determined by single-crystal x-ray diffraction structure refinement; the structure is more complex than those of the commonly observed tetragonal 122 intermetallic phases. Despite...
-
Efficient Usage of Dense GNSS Networks in Central Europe for the Visualization and Investigation of Ionospheric TEC Variations
PublikacjaThe technique of the orthogonal projection of ionosphere electronic content variations for mapping total electron content (TEC) allows us to visualize ionospheric irregularities. For the reconstruction of global ionospheric characteristics, numerous global navigation satellite system (GNSS) receivers located in different regions of the Earth are used as sensors. We used dense GNSS networks in central Europe to detect and investigate...
-
Phase separation in poly(butylene terephthalate)-based materials prepared by solid-state modification
PublikacjaThe morphology of a series of poly(butylene terephthalate) (PBT)/fatty acid dimer diol (FADD)-based copolyesters prepared by solid-state modi fi cation (SSM) was studied. It was shown that in copolyesters containing less than 10 wt% FADD two different phases, i.e. a PBT crystalline phase and a PBT-rich amorphous phase, are present. The FADD residues were more or less homogeneously distributed throughout the interlamellar regions....