Wyszukiwarka
Filtry
wszystkich: 1899
wybranych: 1569
-
Katalog
Filtry wybranego katalogu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: STEEL-CONCRETE SPECIMEN
-
Verification of selected calculation methods regarding shear strength in beams without web reinforcement
PublikacjaThe purpose of the article was to compare selected calculation methods regarding shear strength in reinforced concrete beams without web reinforcement. Several calculation methods were tested. This included codes: PN-EN 1992-1-1:2008, ACI 318-14 and fib Model Code for Concrete Structures 2010. The analysis also consists of authorial methods published in technical literature. Calculations of shear strengths were made based on experimental...
-
GPR investigation of the strengthening system of a historic masonry tower
PublikacjaIn this paper the condition assessment of the strengthening system of a masonry tower was carried out by the GPR method. The study provided unique experimental data acquired during measurements of the reinforced concrete frame embedded in masonry walls. Conducted numerical and experimental investigations were focused on the phenomenon of the diffraction-refraction scattering of the electromagnetic energy. A hyperbola resulting...
-
Study of displacements of a bridge abutment using FEM
PublikacjaSteel sheet piles are often used to support excavations for bridge foundations. When they are left in place in the permanent works, they have the potential to increase foundation bearing capacity and reduce displacements; but their presence is not usually taken into account in foundation design. In this article, the results of finite element analysis of a typical abutment foundation, with and without cover of sheet piles, are presented...
-
The effect of strain rate on the passive layer cracking of 304L stainless steel in chloride solutions based on the differential analysis of electrochemical parameters obtained by means of DEIS
PublikacjaOkreślono wpływ szybkości rozciągania w zakresie 10-5s-1 ÷ 16∙10-5s-1 na niestacjonarny proces elektrochemiczny pękania warstwy pasywnej. Badania przeprowadzono na stali wysokostopowej 304L w temperaturze pokojowej w środowisku chlorków za pomocą dynamicznej elektrochemicznej spektroskopii impedancyjnej (DEIS). W rezultacie uzyskano zestaw chwilowych widm impedancyjnych odzwierciedlających dynamikę badanego układu korozyjnego....
-
Ocena możliwości zastosowania stali NV2-4 w budowie statków LPG= Estimation of NV2-4 steel implementation possibilities in LPG ships construction
PublikacjaPrzedstawiono wyniki badań złączy spawanych ze stali NV2-4 przeznaczonych na konstrukcje naczyń kriogenicznych w statkach LPG. Wykazano przydatność tej stali na tego typu konstrukcje spawane.
-
Building Information Modelling as an opportunity and risk for stakeholders involved in construction investment process
PublikacjaThe requirements to apply Building Information Modelling (BIM) in public investments worldwide are currently very high. Significant interest (sometimes formulated also as a requirement) in BIM technology can be observed also among private investors. Design technology that applies BIM is supported by many private investors due to its numerous advantages. A growing group of construction designers (steel, concrete and reinforced concrete...
-
Influence of separation gap on the structural response of colliding structures under earthquake excitation
PublikacjaThe high level of urbanization in the XXIst century forces the designers to design closely-separated structures and to take into account many factors influencing their response during seismic excitation, which are the most unpredictable loads which can affect civil engineering structures. Interactions between insufficiently adjacent buildings, known as the earthquake-induced structural pounding, may cause serious damage to the structures,...
-
Stalowe panele sandwicz - nowe możliwości wynikające z zastosowania spawania laserowego = All steel sandwich panels - new possibilities introduced by laser welding techniques
PublikacjaW artykule przedstawiono podstawowe dane na temat stalowych paneli typu sandwicz i technik ich wykonywania. Złącze takie charakteryzuje się specyficznymi własnościami, zdecydowanie odmiennymi od klasycznego połączenia spoiną pachwinową, którego cechy wytrzymałościowe i technologiczne są już dobrze opanowane. W podsumowaniu wykazano, że modelowanie jego geometrii musi być prowadzone na znacznie większym poziomie szczegółowości ze...
-
Susceptibility of Cr-Ni-Mn steel to the hydrogen degradation in boiler fuel = Podatnośc stali Cr-Mn-Ni na niszczenie wodorowe w paliwie kotłowym
PublikacjaStal 34HNM poddana różnym obróbkom cieplnym wykazała skłonność do korozji naprężeniowej w pomiarach ze stałą niską szybkością rozciągania i do zmęczenia korozyjnego niskocyklowego. Mechanizmem zniszczenia była degradacja wodorowa. Możliwe źródła pochłaniania wodoru to: korozja, degradacja węglowodorów z tworzeniem się kwasów organicznych i promotorów wnikania wodoru.
-
Corrosion process monitoring by AFM higher harmonic imaging
PublikacjaThe atomic force microscope (AFM) was invented in 1986 as an alternative to the scanning tunnelling microscope, which cannot be used in studies of non-conductive materials. Today the AFM is a powerful, versatile and fundamental tool for visualizing and studying the morphology of material surfaces. Moreover, additional information for some materials can be recovered by analysing the AFM's higher cantilever modes when the cantilever...
-
Lamb wave-based monitoring of shear failure of an adhesive lap joint
PublikacjaThe paper presents a study on the elastic wave propagation in adhesive joints of steel plates subjected to tensile loading. A single lap joint was chosen for analysis because of its simplicity and plurality of applications. Experimental investigations consisted of the uniaxial extension of prepared specimens. Force and displacement values were recorded by a testing machine. Simultaneously, guided Lamb waves were excited and signals...
-
Corrosion behaviour of low carbon steel in artificial seawater using TP, LP, EIS, Harmonic Analysis (HA) and new method Dynamic Electrochemical Impedance Spectroscopy (DEIS)
PublikacjaZe względu na istotną rolę technik elektrochemicznych w badaniach procesów korozyjnych są one szeroko stosowane w monitorowaniu korozji. Celem niniejszej pracy jest zgromadzenie rezultatów wyników doświadczalnych uzyskanych różnymi technikami i znalezienie korelacji między nimi. Własności korozyjne stali stopowej (AISI 1026) w sztucznej wodzie morskiej zostały zbadane z wykorzystaniem ekstrapolacji tafelowskiej (TP), polaryzacji...
-
Badania jakości docierania stali hartowanej docierakami aktywizowanymi w sposób swobodny = Study of hardened steel lapping quality where lapping tools are activized in a free way
PublikacjaPrzedstawiono badania jakości docierania stali hartowanej docierakami zbrojonymi w sposób swobodny. Analizowano wpływ podstawowych warunków obróbki na chropowatość powierzchni obrobionej. Wyznaczono zależność parametru Ra od prędkości i czasu docierania oraz nacisku jednostkowego. Analizowano również zanieczyszczenie powierzchni ścierniwem po docieraniu.
-
Wave propagation in damage assessment of ground anchors
PublikacjaThe inspection possibilities of ground anchors are limited to destructive test such as pull-out test. Guided wave propagation gives an opportunity to develop an inspection system dedicated to determine the condition of inspected element without violation of their integrity. In this paper the experimental study on wave propagation in laboratory models of ground anchors are presented. Experiments were conducted for different bonding...
-
Non-destructive diagnostics of concrete cantilever beam and slab by impact echo method = Nieniszcząca diagnostyka konstrukcji betonowych belek wspornikowych i płyty stropowej za pomocą metody impact echo
PublikacjaPraca poświęcona jest zastosowaniu fal sprężystych na przykładzie w metody impact-echo. Metoda ta wykorzystuje zjawisko propagacji fal wzbudzanych przez mechaniczne uderzenie i ich pomiar za pomocą jednego lub dwóch akcelerometrów. Przeprowadzone testy eksperymentalne dla betonowych wsporników oraz stropu potwierdziły skuteczność metody w wykrywaniu uszkodzeń.
-
Cavitation resistance of OH18N9 steel alloyed with vaidus amount of TiC or Mn by means of laser beam. XIV International Symposium on Gas Flow, Chemical Lasers and High Power Lasers.
PublikacjaPrzedstawiono badania odporności kawitacyjnej stali OH18N9T po laserowym stopowaniu jej powierzchni węglikiem TiC oraz manganem. Wykazano, że wzbogacenie obrabianej stali manganem powoduje przemiany fazowe pod wpływem działania obciążeń kawitacyjnych, co przyczynia się do wzrostu odporności kawitacyjnej. Wzmacnianie stali węglikiem TiC powoduje natomiast zanik zdolności stali do wzmacniania odkształceniowego.
-
Tytanowa międzywarstwa w łącznikach do spawania Al i stopów AlMg ze stalą=Titanium interlayer in transition joints to welding aluminium and aluminium alloys AlMg with steel
PublikacjaPrzedstawiono idee stosowania łączników i ich wytwarzanie oraz własności i niedostatki obecnie stosowanych łączników. Zaprezentowano wyniki prób technologicznych wytwarzania oraz wyniki badań mechanicznych i strukturalnych trójwarstwowego łącznika stal-tytan-aluminium.
-
NON-LOCAL VOLUMETRIC APPROACH TO ANALYSIS DEFECT'S SHAPE INFLUENCE ON SPECIMENS DURABILITY SUBJECTED TO BENDING AND TORSION
PublikacjaThe influence of defect features on fatigue behaviour is a complex trivial issue. Although the important advances over the last decades, the dialectical relationship between the defect orientation and durability is not clearly understood. The paper aims at studying the influence of the orientation of elliptical defects on the durability of samples made of C45 steel. Three types of samples with elliptical defects were subjected...
-
Timber - material of the future. Examples of small wooden architecture structures.
PublikacjaThe aim of this article is to present various types of wood-based products, classified as engineered timber, while specifying the implications of their structural properties for their forms. Timber is used as a construction material due to its fire resistance, good structural characteristics and insulating properties. The advent of new technologies of wood processing and wood-based materials production has converted timber into...
-
Badania eksperymentalne strefy przypodporowej żelbetowych belek częściowo sprężonych
PublikacjaThis project refers to the study the shear zone, under full and partial prestressing in comparison to beams with passive reinforcement.For comparison, variable parameters have been determined:- a/d (from 1,5 to 3,5) - it's shear span to effective depth of the beam . Assuming constant geometrical quantities, "a" is variable.- 26 beams had no vertical shear reinforcement, and the other 26 had closed stirrups.- prestressing intensity...
-
Building damage due to structural pounding during earthquakes
PublikacjaEarthquake-induced pounding between adjacent buildings has been identified as one of the reasons for substantial damage or even total collapse of colliding structures. A major reason leading to interactions in buildings results from the differences in their dynamic parameters and also from insufficient distance between the structures. Although the research on structural pounding has been much advanced, the studies have mainly been...
-
Structural Reliability Assessment Of Corroded Tanker Ship Based On Experimentally Estimated Ultimate Strength
PublikacjaThis work deals with the reliability assessment of a tanker ship hull structure subjected to a vertical bending moment and corrosion degradation. The progressive collapse and ultimate load carrying capacity are estimated based on experimentally tested scaled box-shaped-specimens. The translation of the strength estimate of the scaled specimen to the real tanker ship hull structure is performed based on the dimensional theory developing...
-
Mechanical Properties of Aluminium Bracket Strengthening
PublikacjaThe aim of the research is laboratory investigation of aluminium brackets employed to fasten lightweight curtain walls to building facilities. Tensile loads perpendicular to end plates (vertical) were applied here. The author focused on the solutions intended to increase the load-carrying capacity of aluminium brackets applying the plain washer form A (DIN 125; ISO 7089), plain washer with an outer diameter about 3d (DIN 9021;...
-
CFFT columns in road through railroad crossings
PublikacjaThere were 12801 road through railroad one-level crossings in Poland in 2018. 215 accidents happened at them in 2018. In order to increase safety in rail and road traffic two-level crossings should be used. They are definitely safer and make the traffic more smooth. In the design and construction of two-level intersections of railway and road or path columns of circular cross-section are often used. They can be successfully replaced...
-
Role of bead sequence in underwater welding
PublikacjaThis paper presents examinations of the role of the bead sequence in underwater welding. Two specimens of wet welded layers made by covered electrodes with the use of normalized S355G10+N steel were welded by a reasonable bead sequence. For each specimen, metallographic macro- and micro-scopic tests were done. Then, Vickers HV10 hardness measurements were conducted for each pad weld in the welded layer. The results show that welding...
-
Accelerated large scale test set-up design in natural corrosion marine environment
PublikacjaThe standards for conducting small-scale specimen tests are well developed, but there is a lack of direct guidelines for conducting corrosion tests for large-scale specimens. The objective here is to develop a methodology which may be used in designing an accelerated corrosion test of large-scale structural components subjected to a natural corrosion marine environment. Different factors influencing corrosion degradation of steel...
-
Screw displacement pile shaft deformations measured by vibrating wire and fiber optic systems during a static load test
PublikacjaThis paper describes a full scale static load test performed on a 400 mm diameter screw displacement pile equipped with four different strain measuring systems. Three types of vibrating wire strain gauges (VWSG) were used: global - retrievable, local attached to steel pipe and local concrete embedded. The fourth system was distributed fiber optic sensors based on Rayleigh back scattering (DFOS) - three in the pile cross section....
-
Introducing a Computational Method to Retrofit Damaged Buildings under Seismic Mainshock-Aftershock Sequence
PublikacjaRetrofitting damaged buildings is a challenge for engineers, since commercial software does not have the ability to consider the local damages and deformed shape of a building resulting from the mainshock record of an earthquake before applying the aftershock record. In this research, a computational method for retrofitting of damaged buildings under seismic mainshock-aftershock sequences is proposed, and proposed computational...
-
Load Tests of the Movable Footbridge Over the Port Canal in Ustka
PublikacjaThe paper presents the acceptance tests carried out on the open footbridge over the port canal in the Port of Ustka. The steel footbridge construction is created by a single pylon to which a movable truss span is suspended with a theoretical span of 52.3 m. The studies about load test of the object included static and dynamic extortion and measurements. In static tests the ballast was of pallets with concrete blocks. Dynamic studies...
-
LNG TANK IN ŚWINOUJŚCIE: NONLINEAR ANALYSIS OF THE TANK DOME ELEMENTS BEHAVIOUR
PublikacjaIn this paper, the dome of a tank in the Świnoujście LNG terminal is analysed. Some of the rafter ribs at the connection with hangers were not mounted during construction of the tank dome. Therefore, it has become necessary to estimate its response, which has been done with the aid of some computational models of the dome, that have been created in the finite element method environment. Different local models are studied, aiming...
-
Effects of Xanthan Gum Biopolymer on the Permeability, Odometer, Unconfined Compressive and Triaxial Shear Behavior of a Sand
PublikacjaBiopolymers, which are microbially induced polymers, can be used as an alternative material to improve engineering performance of soils. In this paper, a laboratory study of 0.075-1.0 mm size sand and biopolymer (i.e., xanthan gum) mixtures with various mix ratios (0%, 0.5%, 1.0%, and 1.5%) was performed. The materials, specimen preparation, and test methods are described, as are the results of a suite of permeability, odometer, unconfined...
-
Retrofitted vibro-pressed pavement bricks and their impregnation in modern architecture.
PublikacjaRecent construction projects require new properties of concrete building materials. The paper describes the technological methods of retrofitting of vibro-pressed concrete pavement brick and shows the results of improving physical properties of concrete by application of different impregnation agents.
-
Impact performance of novel multi-layered prepacked aggregate fibrous composites under compression and bending
PublikacjaMulti-layered Prepacked aggregate fibrous composite (MLPAFC) is a new type of concrete, which is prepared in two subsequent stages of aggregate-fibre skeleton prepacking and cementitious grouting. In this study, ten MLPAFC mixtures were prepared in three subsequent layers incorporating different contents of four different types of steel fibres. Long and short hooked-end and crimped steel fibers were adopted with 3.0 and 1.5% dosages...
-
Experiments and numerical analyses for composite RC-EPS slabs
PublikacjaW artykule przedstawiono wyniki doświadczalne i numeryczne dla kompozytowych płyt złożonych z żelbetu i styropianu. Wykonano doświadczenia dla płyt w skali 1:1 podczas zginania. Wyniki doświadczalne zostały modelowane stosując 2 różne modele: sprężysto-plastyczny i połączony sprężysto-plastyczny z degradacja sztywności. Oba model zostały wyposażone w długość charakterystyczna mikrostruktury. Osiągnięto dobra zgodność miedzy...
-
Damage Analysis of Tensioning Cable Anchorage Zone of a Bridge Superstructure, Using CDP Abaqus Material Model
PublikacjaNumerical analysis of the tensioning cables anchorage zone of a bridge superstructure is presented in this paper. It aims to identify why severe concrete cracking occurs during the tensioning process in the vicinity of anchor heads. In order to simulate the tensioning, among others, a so-called local numerical model of a section of the bridge superstructure was created in the Abaqus Finite Element Method (FEM) environment. The...
-
Wave Frequency Effects on Damage Imaging in Adhesive Joints Using Lamb Waves and RMS
PublikacjaStructural adhesive joints have numerous applications in many fields of industry. The gradual deterioration of adhesive material over time causes a possibility of unexpected failure and the need for non-destructive testing of existing joints. The Lamb wave propagation method is one of the most promising techniques for the damage identification of such connections. The aim of this study was experimental and numerical research on...
-
Influence of Rock Dust Additives as Fine Aggregate Replacement on Properties of Cement Composites—A Review
PublikacjaConcrete production consumes enormous amounts of fossil fuels, raw materials, and is energy intensive. Therefore, scientific research is being conducted worldwide regarding the possibility of using by-products in the production of concrete. The objective is not only to identify substitutes for cement clinker, but also to identify materials that can be used as aggregate in mortar and concrete productions. Among the potential alternative...
-
Pomiary naprężeń w warstwie wierzchniej stali duplex metodą dyfrakcji promieniowania rentgenowskiego g-sin2Ψ = Residual stress measurements in duplex steel surface layers by g-sin2Ψ x-ray diffraction method
PublikacjaPrzedstawiono wyniki pomiarów naprężeń w warstwie wierzchniej z wykorzystaniem metody dyfrakcji promieniowania rentgenowskiego g-sin2. Wyjaśniono zasady przeprowadzania pomiarów naprężeń na próbkach walcowych o małej średnicy. Badania prowadzono na próbkach okrągłych ze stali duplex, poddanych procesom nagniatania. Stwierdzono występowanie naprężeń ściskających w warstwach powierzchniowych wszystkich badanych próbek oraz istotne...
-
The geodetic monitoring of the engineering structure – a practical solution of the problem in 3D space
PublikacjaThe study raises the issues concerning the automatic system designed for the monitoring of movement of controlled points, located on the roof covering of the Forest Opera in Sopot. It presents the calculation algorithm proposed by authors. It takes into account the specific design and location of the test object. High forest stand makes it difficult to use distant reference points. Hence the reference points used to study the stability...
-
Application of lightweight cement composite with foamed glass aggregate in shell structures
PublikacjaThe purpose of the paper is to investigate the abilities of applying Granulated Expanded Glass Aggregate (GEGA) as a natural volume substitute of aggregate as a component of lightweight concrete. The GEGA aggregates used in the experiments were made of confused glass waste. In order to achieve satisfactory strength of concrete Granulated Ash Aggregate (GAA) was added as well. To produce specimens three grain sizes of aggregates...
-
Models of Structures in Didactics
PublikacjaThe final aim of teaching students subjects, such as structural mechanics, reinforced concrete, and steel structures is to teach them how structures work in a given building as well as to provide them with skills enabling them to calculate and design structures. The behavioral model of the structure, contrary to the architectural model, which focuses mainly on the external form of the building, shows workings from both the static...
-
The use of fibre-reinforced polymers (FRP) in bridges as a favourable solution for the environment
PublikacjaThe purpose of this article is to show the modern engineering, in which sustainability and taking care of ecology play a significant role. The authors are focused on FRP composite materials and their applications in civil engineering. Case studies showing renovation and design of new bridges with the use of FRP are presented and discussed to clarify benefits, which this solution provides. Main advantages of FRP materials in comparison...
-
A HISTORICAL BUILDING'S RESTORATION IN THE CONSTRUCTIONAL ASPECT ON THE EXAMPLE OF A BUILDING LOCATED IN POLAND
PublikacjaObjects of cultural heritage are an extremely important element in the proper functioning of the social life. They provide information on our ancestors' actions, as well as shape our culture and social awareness. It is important for the historical objects to provide those information accurately, that is without any unnecessary human intervention over the years of the monument's existence. However, it is not always possible due...
-
Influence of Gd deposition on the oxidation behavior and electrical properties of a layered system consisting of Crofer 22 APU and MnCo2O4 spinel
PublikacjaIn the study, the surface of the Crofer 22APU ferritic steel was modified with gadolinium oxide nanoparticles and a protective-conducting layer consisting of the MnCo2O4 spinel. This system was studied in the context of application in IT-SOFC interconnects. Four types of samples were studied: unmodified steel, steel coated with a manganese-cobalt spinel layer, steel modified with gadolinium oxide nanoparticles, and a system consisting...
-
The effect of road restraint systems on the level of road safety - Polish experience
PublikacjaRoadside accidents happen when a vehicle runs off the road. The majority of these accidents are very severe because leaving the road is usually followed by hitting a solid obstacle (tree, pole, support, culvert front wall, barrier). Roadsides are some of the most important issues of road safety. They have been studied for years to identify roadside hazards and the effectiveness of road safety measures such as restraint systems....
-
Optimization of Hydrogen Utilization and Process Efficiency in the Direct Reduction of Iron Oxide Pellets: A Comprehensive Analysis of Processing Parameters and Pellet Composition
PublikacjaThe article deals with the H2 consumption for different processing conditions and the composition of the processed pellets during the direct reduction process. The experiments are carried out at 600–1300 °C, with gas pressures of 1–5 bar, gas flow rates of 1–5 L min−1, and basicity indices of 0 to 2.15. Pellets with different compositions of TiO2, Al2O3, CaO, and SiO2 are analyzed. The gas flow rate is crucial, with 0–10 L min−1...
-
Application of advanced spectroscopic methods in the assessment of the leachability degree of hazardous elements from the matrix of cellular concretea
PublikacjaDue to its structure, autoclaved cellular concrete exhibits good insulating properties with relatively high compressive strength values. It is increasingly used in construction because of its economic attractiveness. Autoclaved cellular concrete is mainly used in interior structure layers, and therefore its potential exposure to heavy metal leaching from the matrix may be related to the presence of a high pH medium from other materials...
-
DEFORMATIONS OF INNOVATIVE COLD-FORMED GEB SECTIONS
PublikacjaPermanent urban growth of the world of today world implies demanding challenges for the steel construction industry. Nowadays, one of the most important issues is the cost optimization of steel structures. Since the weight of building materials is a major component of the total cost, engineers and designers try to reduce structural weight, without compromising durability and sustainability of a steel structure. Therefore, light...
-
CFGFRPT Piles with a Circular Cross-Section and their Application in Offshore Structures
PublikacjaThe possibilities of using concrete piles in a polymer composite reinforced with glass fibres in offshore facilities were shown. Laboratory tests of CFGFRPT type piles compressed axially and in eccentric compression for the analysis of CFGFRPT piles were used. Methods of analysis of dynamic systems for mathematical modelling of the displacement of the hammer in the pile driving process were applied. The possibilities of combining...
-
Assessment of the application of CEM III with exposed aggregate as an alternative to CEM I for road pavements
PublikacjaThe article presents a results of study on the impact of replacing CEM I SR3/NA by CEMIII/A LH/HSR/NAon the mechanical properties and durability of pavement concrete with exposed aggregate. Was used granite aggregate and washed sand. Water/cement () ratio in the tested concretes constituted 0.35 and 0.4 and part of the cement was replaced with a 5% addition of natural pozzolana – zeolite. Compressive strength tests were performed...